SEARCH · Engineering Papers

Results for “surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Polymer–Particle Interactions and Spinnability

We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.

25 ENERGY STORAGE↗

DOE OSTI2024

Metallurgical Analysis of the High Flux Isotope Reactor (HFIR) Carrier Lifting Bails (Rev.1)

The dissolution rates of the aluminum alloys in the High Flux Isotope Reactor (HFIR) element carriers and the Material Test Reactor (MTR) L-bundles in the H-Canyon facility have been identified as the possible cause of extended dissolutions that result in significant time and financial expenditures. A study, carried out by Savannah River National Laboratory (SRNL) to determine relationships between the dissolution rates and the metallurgical properties of the aluminum alloy materials of construction of the HFIR carriers and the L-bundles, considered the dissolution rates of aluminum alloy (AA) series 1100, 6061, and 6063. The study determined that the aluminum alloy compositions played a principal role in the dissolution rate of the carrier/bundle components. Higher dissolution rates were correlated with lower concentrations of the minor element additions in the alloys and with specific element concentrations. Aluminum alloys 1100 and 6063 were found to have similar dissolution rates that were approximately two orders of magnitude (100X) greater than those of AA6061. Based on the results of the dissolution behavior study, a Technical Assistance Request (TAR) was first issued to determine if the replacement of AA6061-T6 with AA6063-T6 is feasible for the HFIR carrier lifting bails. A Technical Task Request was then issued to consider AA6063-T5 as well as other alloys to improve possible supply chain issues. The metallurgical properties of the L-bundle (specifically the end caps) were not evaluated in this report because L-Bundle drawings already allow for the use of AA6063-T6 in all structural components. The HFIR carriers are composed of thin-walled components with significant surface areas that allow for relatively quick overall dissolution times. Conversely, the carrier lifting bails and the supporting constituents are composed of solid bars and thick plate regions with relatively small surface areas that experience longer overall dissolution times. While the MTR L-bundle design includes allowances for the materials of construction to be either AA6061-T6 or AA6063-T6, the HFIR carriers are specified to be constructed fully with AA6061-T6 alloy. This report analyzes the recommendations of the dissolution behavior study to replace the materials of construction of the HFIR carrier lifting bails. The analysis considers the operational requirements of the lifting bail and its supporting structures. To decrease dissolution times, the analysis considers direct replacement of the material as well as reductions in the thicknesses of the components to decrease the mass of the elements. Material reductions are considered on options for using either AA6061 and/or AA6063. The calculations are based on specifications from the American Society of Mechanical Engineer (ASME) and The Aluminum Association, Inc. design codes. The analysis finds that direct replacement of the lifting bail material of construction with AA6063-T6, and AA6063-T5 as well as reductions in the dimensions of the lifting bail components are acceptable. Note that this study considers the structural suitability of the alloys. It does not consider their dissolution rates in the dissolvers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1981

Stabilizing platinum in phosphoric acid fuel cells

The cathode of the phosphoric acid fuel cell uses a high surface area platinum catalyst supported on a carbon substrate. During operation, the small platinum crystallites sinter, causing loss in cell performance. A support was developed that stabilizes platinum in the high surface area condition by retarding or preventing the sintering process. The approach is to form etch pits in the carbon by oxidizing the carbon in the presence of a metal oxide catalyst, remove the metal oxide by an acid wash, and then deposit platinum in these pits. Results confirm the formation of etch pits in each of the three supports chosen for investigation: Vulcan XC-72R, Vulcan XC-72 that was graphized at 2500 C, and Shawinigan Acetylene Black.

Remick, R. J.↗

DOE OSTI2023

Solvent-Treated Zirconium-Based Nanoporous UiO-66 Metal–Organic Frameworks for Enhanced CO 2 Capture

Metal–organic framework (MOF)-derived nanoscale porous materials are widely deployed in carbon capture, but the CO 2 capacity is varied by different post-treatments, and its mechanism is still unclear. In this work, we prepared UiO-66 and treated it with methanol solvent and thermal activation approaches, which showed ~3 times enhanced CO 2 capacities from 15.1 to 45.0 mg/g and excellent recyclability of 10 cycles. The methanol treatment efficiently removes the residual guest molecules, including N,N-dimethylformamide, dangling organic linkers, and their derivatives, in the micropores (~0.8 nm) of UiO-66 and improves the surface area, pore volume, and void fraction to enhance the CO 2 capacity close to the ideal UiO-66 materials. The molecular dynamics simulation also proved a good linear relationship between the surface areas, void fraction, and CO 2 capacity. This work provides a deep understanding of the MOF’s activation mechanism and its applications in CO 2 capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1987

Is regolith absorbtion the explanation for the transition from early to present Mars climate

Experimental data is presented for CO2 adsorption on palagonites (now thought to provide the most acceptable spectral match to Mars weathering products). When corrected for great differences in specific surface area, the adsorptive behavior exhibited by palogonites, nontronite, and basalt with respect to CO2 can be (approx.) described by the same generic equation. Using this relationship normalized to a Mars soil surface area, and the dependence of subsurface temperatures on latitude and depth, the current inventory of regolith absorbed CO2 was estimated.

Fanale, F. P.↗

DOE OSTI2023

Engineering catalytical electrodes for applications in energy areas

An ink formulation and electrode that enhances hydrogen production, oxygen production, carbon dioxide reduction and other electrocatalytic reactions. Embodiments include an ink formulation with polymer binders having different catalytical precursors and a 3D electrode produced by additive manufacturing from the inventor's ink formulation. Various embodiments of the inventor's apparatus, systems, and methods provide inks that that are 3D-printed into patterns that optimize surface area and flow. The catalytic materials are imbedded into the ink matrix which is then printed into a 3D structure that has architecture that optimizes surface area and flow properties.

Liang, Siwei↗

DOE OSTI2026

Highly Crystalline and Porous Borocarbonitrides as Metal‐Free Catalysts for Boosted N‐Heterocycle Dehydrogenation

Safe and efficient hydrogen storage is pivotal for enabling a clean hydrogen economy. Liquid organic hydrogen carriers (LOHCs) offer a practical solution, but their deployment is hindered by the lack of highly active and economical dehydrogenation catalysts. In this work, we report a metal‐free catalyst design that overcomes the long‐standing trade‐off between crystallinity and surface area in two‐dimensional frameworks for highly efficient dehydrogenation of LOHCs. A flux‐assisted reconstruction strategy transforms amorphous borocarbonitrides (AM‐BCN) into highly crystalline, defect‐rich BCN nanosheets (C‐BCN) with large surface area and accessible porosity, as confirmed by complementary spectroscopic, x‐ray, and neutron analyses. C‐BCN catalyzes the acceptor‐less dehydrogenation of aza‐fused LOHCs with quantitative hydrogen release under mild conditions, outperforming AM‐BCN and previously reported metal‐free scaffolds. Mechanistic insights from x‐ray, neutron scattering, and theoretical calculations identify open C‐B‐N and N‐B‐N defect motifs as the primary active sites. This work establishes a generalizable strategy to engineer crystalline, porous, defect‐rich two‐dimensional lattices and demonstrates a highly active metal‐free platform for LOHC dehydrogenation with high‐purity H 2 generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Beyond the Global Brain Differences: Intraindividual Variability Differences in 1q21.1 Distal and 15q11.2 BP1-BP2 Deletion Carriers

Carriers of the 1q21.1 distal and 15q11.2 BP1-BP2 copy number variants exhibit regional and global brain differences compared with noncarriers. However, interpreting regional differences is challenging if a global difference drives the regional brain differences. Intraindividual variability measures can be used to test for regional differences beyond global differences in brain structure. Magnetic resonance imaging data were used to obtain regional brain values for 1q21.1 distal deletion (n = 30) and duplication (n = 27) and 15q11.2 BP1-BP2 deletion (n = 170) and duplication (n = 243) carriers and matched noncarriers (n = 2350). Regional intra-deviation scores, i.e., the standardized difference between an individual’s regional difference and global difference, were used to test for regional differences that diverge from the global difference. For the 1q21.1 distal deletion carriers, cortical surface area for regions in the medial visual cortex, posterior cingulate, and temporal pole differed less and regions in the prefrontal and superior temporal cortex differed more than the global difference in cortical surface area. For the 15q11.2 BP1-BP2 deletion carriers, cortical thickness in regions in the medial visual cortex, auditory cortex, and temporal pole differed less and the prefrontal and somatosensory cortex differed more than the global difference in cortical thickness. We find evidence for regional effects beyond differences in global brain measures in 1q21.1 distal and 15q11.2 BP1-BP2 copy number variants. The results provide new insight into brain profiling of the 1q21.1 distal and 15q11.2 BP1-BP2 copy number variants, with the potential to increase understanding of the mechanisms involved in altered neurodevelopment.

15q11.2 BP1-BP2↗

DOE OSTI2021

Maximum CO 2 diffusion inside leaves is limited by the scaling of cell size and genome size

Maintaining high rates of photosynthesis in leaves requires efficient movement of CO 2 from the atmosphere to the mesophyll cells inside the leaf where CO 2 is converted into sugar. CO 2 diffusion inside the leaf depends directly on the structure of the mesophyll cells and their surrounding airspace, which have been difficult to characterize because of their inherently three-dimensional organization. Yet faster CO 2 diffusion inside the leaf was probably critical in elevating rates of photosynthesis that occurred among angiosperm lineages. Here we characterize the three-dimensional surface area of the leaf mesophyll across vascular plants. We show that genome size determines the sizes and packing densities of cells in all leaf tissues and that smaller cells enable more mesophyll surface area to be packed into the leaf volume, facilitating higher CO 2 diffusion. Measurements and modelling revealed that the spongy mesophyll layer better facilitates gaseous phase diffusion while the palisade mesophyll layer better facilitates liquid-phase diffusion. Our results demonstrate that genome downsizing among the angiosperms was critical to restructuring the entire pathway of CO 2 diffusion into and through the leaf, maintaining high rates of CO 2 supply to the leaf mesophyll despite declining atmospheric CO 2 levels during the Cretaceous.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Coupling Remote Sensing and Sonar Measurements to Estimate Availability of Suitable Backwater Nursery Habitat for Colorado Pikeminnow

13 HYDRO ENERGY↗

NASA NTRS1993

Pulmonary diffusing capacity, capillary blood volume, and cardiac output during sustained microgravity

We measured pulmonary diffusing capacity (DL), diffusing capacity per unit lung volume, pulmonary capillary blood volume (Vc), membrane diffusing capacity (Dm), pulmonary capillary blood flow or cardiac output (Qc), and cardiac stroke volume (SV) in four subjects exposed to nine days of microgravity. DL in microgravity was elevated compared with preflight standing values and was higher than preflight supine because of the elevation of both Vc and Dm. The elevation in Vc was comparable to that measured supine in 1 G, but the increase in Dm was in sharp contrast to the supine value. We postulate that, in 0 G, pulmonary capillary blood is evenly distributed throughout the lung, providing for uniform capillary filling, leading to an increase in the surface area available for diffusion. By contrast, in the supine 1-G state, the capillaries are less evenly filled, and although a similar increase in blood volume is observed, the corresponding increase in surface area does not occur. DL and its subdivisions showed no adaptive changes from the first measurement 24 h after the start of 0 G to eight days later. Similarly, there were no trends in the postflight data, suggesting that the principal mechanism of these changes was gravitational. The increase in Dm suggests that subclinical pulmonary edema did not result from exposure to 0 G. Qc was modestly increased inflight and decreased postflight compared with preflight standing. Compared with preflight standing, SV was increased 46 percent inflight and decreased 14 percent in the 1st week postflight. There were temporal changes in Qc and SV during 0 G, with the highest values recorded at the first measurement, 24 h into the flight. The lowest values of Qc and SV occurred on the day of return.

Prisk, G. K.↗

NASA NTRSDate not supplied

Polymer Aerogels for Lunar Applications and Beyond

As the Space Community endeavors to reach new heights of exploration, materials for extreme environment are on the forefront of research. One such material would include polymer aerogels; lightweight solids with nano-scale pore size, high internal surface area, low thermal conductivity, and extremely high porosities. Due to these interesting properties, aerogels are ideal as thermal insulators but are by no means limited to this application. The high porosity and surface area also make aerogels an ideal host system for particle incorporation for applications such as catalyst supports, sensor platforms, and vibro-acoustic mitigating materials. Polymer aerogels also have the potential to combat issues found in extraterrestrial environments such as dust and radiation mitigation. Herein, current research will be discussed as it pertains to Space exploration.

Stephanie Vivod↗

NASA NTRS1993

Soft x ray properties of the Geminga pulsar

The ROSAT soft x ray spectrum and pulse profile of the Geminga pulsar are analyzed and interpreted in terms of thermal emission from the surface of the neutron star. The x ray spectrum appears to consist of two blackbody components with T(sub 1) = (5.2 +/- 1.0) x 10 (exp 5) K and T(sub 2) approximately 3 x 10(exp 6) K, respectively. The inferred ratio of surface areas, A(sub 2)/A(sub 1), is approximately 3 x 10(exp -5). Both components are highly modulated at the pulsar rotation period, but the harder x ray pulse is narrower, and leads the main (soft) x ray pulse by about 105 deg of phase. The soft x ray component is interpreted as photospheric cooling of much of the neutron star's surface area, while the small, hot region could be part of the much smaller polar cap heated by energetic particles flowing inward from the magnetospheric accelerator which is responsible for the production of Geminga's gamma rays. Geminga's gamma ray emission is consistent with outer-magnetosphere accelerator models for highly inclined dipoles. These predict the beaming of energetic gamma rays close enough to the star to give copious e(+/-) production in the stellar magnetic field and a large circumstellar pair density from pair inflow toward the surface. These pairs may quench radio emission, and also reflect most of the hard polar cap x rays back to the stellar surface by cyclotron resonance scattering. They are then reemitted from that much larger area at the lower temperature T(sub 1). The single-peaked nature of the x ray pulse and its energy-dependent phase suggest an off-center dipole geometry for the surface magnetic field. Under the assumption that the soft x ray emission comes from the full surface of a neutron star of radius R = 10 km, a distance estimate of (150-400) pc is derived. This range is consistent with the fit interstellar column density of (1.5 +/- 0.5) x 10(exp 20) cm(exp -2). Distances less than 150 pc are probably ruled out both by the lower limit on the column density, and also by the requirement that the Rayleigh-Jeans extrapolation of the soft x ray spectrum not exceed the observed blue flux of the faint optical counterpart. This distance estimate implies that Geminga's efficiency for converting spindown power into gamma-rays is near unity, and that there may be significant beaming of the gamma rays as well. These results tend to bolster the prospect that most of the unidentified high-energy gamma ray sources in the Galactic plane are pulsars, some of which may be radio quiet.

Halpern, J. P.↗

DOE OSTI2021

Advanced Multi-Tube Mixer Combustion for 65% Efficiency (Final Report)

This project targeted advanced low NOx combustion for advanced gas turbines capable of 65%, or greater, efficiency in combined cycle application. This technology advancement has further potential to benefit gas turbines used in coal based IGCC applications with pre-combustion carbon capture and hydrogen as the resulting fuel. The program developed and synthesized the most advanced combustion system capable of achieving low NOX emissions up to turbine inlet temperatures of 3100F while also supporting the load-following needs of a modern grid. The combustion system contributes to the overall gas turbine efficiency goal by setting the maximum cycle temperature achievable for a given NOX level and by minimizing the through-combustor air flow pressure drop. Focus areas for this project targeted maximizing the turbine inlet temperature entitlement, as constrained by emissions considerations. The design also minimized parasitic air flow pressure drop by using advanced cooling techniques and performance materials selections and by minimizing hot surface area. These two technology objectives (maximum, emissions-compliant cycle temperature and minimum air flow pressure drop) were integrated into a prototype design. The primarily analytical project sought to identify the most promising technologies to meet these objectives. Additional critical “jugular” data were obtained from multi-tube mixer tests to realize the potential of leveraging “micro flames” for minimizing overall hot surface area. This data was used, in conjunction with an understanding of advanced material and cooling design technologies, to analytically develop multiple design concepts. Phase I focused on in-depth engineering analysis and design, with minimal supporting laboratory testing to enable a selection of the top three combustion architectures for achieving these overall objectives. Phase II of the program developed the selected design through a combination of sub-scale testing and analytical efforts. Early tests included a cold-flow cascade to establish aerodynamic performance characteristics and a sub-scale fired test at GE Global Research in Niskayuna, NY, to establish cooling and heat transfer characteristics in conjunction with combustion performance. The data from these tests validated the analytical models to ultimately design a full-scale, test article to evaluate at prototypical pressure and temperature conditions at GE Gas Power’s Gas Turbine Technology Laboratory in Greenville, SC. GE Gas Power also developed, tested, and recommended a suitable seal design to be applied to the unique features of the combustor. To assess the technology challenges from prospective future production of the combustor from a ceramic matrix composite material, screening tests of Environmental Barrier Coatings were completed.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2021

Retrospective Analysis of Backwater Habitat Availability Using Remote Sensing

Low-velocity channel-margin habitats serve as important nursery habitats for the endangered Colorado pikeminnow (Ptychocheilus lucius) in the middle Green River between Jensen and Ouray, Utah. These habitats, known as backwaters, are associated with emergent sandbars, and are shaped and reformed annually by peak flows. Our recent knowledge about backwater characteristics and dynamics that is summarized in the synthesis report (Grippo et al. 2015) was based on detailed annual survey data from a relatively small sample of backwaters that were collected from 2003 to 2014 and reach-wide evaluations of backwater surface area based on manual interpretation of aerial and satellite imagery. Methods that bridge the gap between the detailed surveys from a small number of backwaters and the reach-wide assessment of their surface area would enable an assessment of the availability of backwater habitats that meet the minimum depth requirements for suitable habitat for Colorado pikeminnow. In 2015 Argonne National Laboratory (Argonne) tested three regression models—linear, multiple, and partial least square (PLS) regression models—for estimating backwater depth using National Agriculture Imagery Program (NAIP) imagery collected in July 2006 that covered the Jensen-Ouray reach of the Green River (Hamada and LaGory 2016). The results suggested that a PLS regression model showed high correlation with the reference depth (R 2 = 0.69) and had the most unbiased and consistent estimate of backwater depth. The results also indicated that the PLS model would provide reasonable estimates of the amount of habitat providing a minimum suitable depth of 30 cm for young-of-the-year Colorado pikeminnow, even though absolute depth estimates may be uncertain for backwater areas deeper than approximately 40 cm. The study also provided insights regarding the amount and the selection of calibration and validation (cal-val) data needed for improving the accuracy of depth prediction.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1980

Volume changes in Ganymede and Callisto and the origin of grooved terrain

Internal melting and differentiation of Ganymede and Callisto may have caused an increase in the surface area of these bodies early in their histories of up to 5-7%. Subsequent refreezing of internal liquid water due to solid state convection in an ice crust should not have caused significant surface area changes. Expansion due to differentiation may have caused formation of grooved terrain in Ganymede. These calculations suggest that grooved terrain formation is essentially a replacement and/or deformation process, with no more than about 15% of grooved terrain actually being new material. The absence of grooved terrain on Callisto may be due to the effects of a thicker crust and a lower expansion rate.

Squyres, S. W.↗

DOE OSTI2022

Boosting the H 2 –D 2 Exchange Activity of Dilute Nanoporous Ti–Cu Catalysts through Oxidation–Reduction Cycle–Induced Restructuring

The use of nanoporous metals as catalysts has attracted significant interest in recent years. Their high-curvature, nanoscale ligaments provide not only high surface area but also a high density of undercoordinated step edge and kink sites. However, their long-term stability, especially at higher temperatures, is often limited by thermal coarsening and the associated loss of surface area. Herein, it is demonstrated that the nanoscale morphology of nanoporous Cu can be regenerated by applying oxidation/reduction cycles at 250 °C. Specifically, the morphological evolution and H 2 dissociation activity of hierarchical nanoporous Cu catalysts doped with Ti during structural rearrangement triggered by oxidative and reductive atmospheres at elevated temperatures are studied. In addition to coarsening of the structure at elevated temperatures, oxidation at 400 °C causes an expansion of the ligaments. Further, subsequent reduction at 400 °C leads to the formation of particles and a drop in the H 2 dissociation activity compared the fresh catalyst. However, performing the redox cycle at 250 °C reverses coarsening and boosts the H 2 dissociation activity for the hydrogen–deuterium (H 2 –D 2 ) reaction. Herein, the possibility to reverse coarsening is demonstrated, thereby mitigating the loss of activity frequently observed in nanoporous catalysts.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Hot corrosion behavior of 304 & P91 graded composite transition joint under molten sulfate salts

A novel graded composite transition joint (GCTJ) between AISI 304 stainless steel and ASTM A335 P91 steel, has been demonstrated remarkablely superior creep performance compared to the conventional dissimilar metal weldment (DMW) under equivalent conditions. However, this advance is challenged by hot corrosion under salt deposition at elevated temperatures. Here, this study investigates the hot corrosion behavior of 304&P91 GCTJ exposed to sulfate salts at 700°C. Compared to the 304 steel, corrosion attacks initiate in the P91 triangle, where the dual-phase microstructure of ferrite and tempered martensite significantly influences pitting initiation. Anodic dissolution mainly occurs within the tempered martensite due to more vulnerable sites within the tempered martensite. With prolonged exposure, corrosion propagates across both phases, and the corrosion depth within the P91 triangle is related to the exposed surface area ratio between 304 and P91. Electrochemical analysis reveals the occurrence of galvanic corrosion between the 304 and P91, with a positive linear relationship between anodic dissolution current density (I a ) and the exposed surface area ratio between 304 and P91 in molten salts, further emphasizing the critical impact of this ratio on the corrosion severity in the P91 triangle. These findings underscore the importance of transition zone design optimization in mitigating localized corrosion.

Galvanic corrosion↗