Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Strainrange partitioning - A total strain range version

Procedures are presented for expressing the Strainrange Partitioning (SRP) method for creep fatigue life prediction in terms of total strain range. Inelastic and elastic strain-range - life relations are summed to give total strain-range - life relations. The life components due to inelastic strains are dealt with using conventional SRP procedures while the life components due to elastic strains are expressed as families of time-dependent terms for each type of SRP cycle. Cyclic constitutive material behavior plays an important role in establishing the elastic strain-range life relations as well as the partitioning of the inelastic strains. To apply the approach, however, it is not necessary to have to determine the magnitude of the inelastic strain range. The total strain SRP approach is evaluated and verified using two nickel base superalloys, AF2-1DA and Rene 95. Excellent agreement is demonstrated between observed and predicted cyclic lifetimes with 70 to 80 percent of the predicted lives falling within factors of two of the observed lives. The total strain-range SRP approach should be of considerable practical value to designers who are faced with creep-fatigue problems for which the inelastic strains cannot be calculated with sufficient accuracy to make reliable life predictions by the conventional inelastic strain range SRP approach.

Halford, G. R.↗
NASA NTRS2013

Longitudinally Jointed Edge-wise Compression Honeycomb Composite Sandwich Coupon Testing and FE Analysis: Three Methods of Strain Measurement, and Comparison

Three means (i.e., typical foil strain gages, fiber optic sensors, and a digital image correlation (DIC) system) were implemented to measure strains on the back and front surfaces of a longitudinally jointed curved test article subjected to edge-wise compression testing, at NASA Goddard Space Flight Center, according to ASTM C364. The Pre-test finite element analysis (FEA) was conducted to assess ultimate failure load and predict strain distribution pattern throughout the test coupon. The predicted strain pattern contours were then utilized as guidelines for installing the strain measurement instrumentations. The strain gages and fiber optic sensors were bonded on the specimen at locations with nearly the same strain values, as close as possible to each other, so that, comparisons between the measured strains by strain gages and fiber optic sensors, as well as the DIC system are justified. The test article was loaded to failure (at approximately 38 kips), at the strain value of approximately 10,000mu epsilon As a part of this study, the validity of the measured strains by fiber optic sensors is examined against the strain gage and DIC data, and also will be compared with FEA predictions.

Farrokh, Babak↗
DOE OSTI2018

Failure behavior of SiC/SiC composite tubes under strain rates similar to the pellet-cladding mechanical interaction phase of reactivity-initiated accidents

The mechanical response of a nuclear-grade silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite was investigated under mechanical loading conditions mimicking the pellet-cladding mechanical interaction (PCMI) phase of a reactivity-initiated accident (RIA). In a RIA, cladding deformation and failure can be induced by the rapid thermal expansion of the nuclear fuel. A pulse-controlled modified-burst test was used to investigate RIA-like PCMI scenarios on SiC/SiC composite samples at pulse widths from 12 to 100 ms.The strain-driven nature of the cladding sample deformation was due to the rapid internal pressurization and subsequent expansion of a secondary tube. A digital-image correlation technique was used to measure strains from the speckle-painted outer surface of the tubes. The failure strains of samples tested at slower rates, such as RIA event durations of 52 and 100 ms, showed good agreement with the literature-reported values for similar composites tested at slow strain rates. Additionally, the failure strain showed good agreement with reference expansion-due-to-compression tests at slow strain rate. However, a decrease in the failure strain was determined for the fast-rate (12 ms) tests. This indicated that the failure strain of these composites might be influenced by the strain rate during RIA-like events. In conclusion, the failure strains observed in the tests corresponded to local energy depositions of approximately 50 cal/g UO 2 from hot zero power, with an initial condition of pellet–cladding gap closure prior to the event. In-pile transient testing of these concepts that would result in hoop strain due to PCMI in the range of 0.5–1.0% is recommended.

36 MATERIALS SCIENCE↗
DOE OSTI2015

In Operando Strain Measurement of Bicontinuous Silicon-Coated Nickel Inverse Opal Anodes for Li-Ion Batteries

Elastic strains are measured in operando in a nanostructured silicon-coated nickel inverse opal scaffold anode, using X-ray diffraction to study the Si (de)lithiation-induced Ni strains. The volume expansion upon lithiation of the Si in the anode is constrained by the surrounding Ni scaffold, causing mismatch stresses and strains in the Si and Ni phases during cycling. The Ni strains are measured in operando during (dis)charge cycles, using diffraction peak position and peak broadness to describe the distribution of strain in the Ni. During lithiation, compressive strains in the Ni first increase linearly with charge, after which a gradually decreasing strain rate is observed as the maximum lithiation state is approached; upon delithiation a similar process occurs. In-plane average compressive strains on the order of 990 ± 40 με are measured in the Ni scaffold during lithiation, corresponding to compressive stresses of 215 ± 9 MPa. Here, the decreasing strain rates and decreasing maximum and recovered strains suggest that plasticity in Ni and/or Si, as well as delamination between Ni and Si, may occur during cycling. Rate sensitivity in capacity is correlated with strain and a maximum Ni compressive stress of 230 ± 40 MPa is measured at the maximum state of lithiation.

25 ENERGY STORAGE↗
DOE OSTI2020

Predicting the proximity to macroscopic failure using local strain populations from dynamic in situ X-ray tomography triaxial compression experiments on rocks

Predicting the proximity of large-scale dynamic failure is a critical concern in the engineering and geophysical sciences. Here we use evolving contractive, dilatational, and shear strain deformation preceding failure in dynamic X-ray tomography experiments to examine which strain components best predict the proximity to failure. We develop machine learning models to predict the proximity to failure using time series of three-dimensional local incremental strain tensor fields acquired in rock deformation experiments under stress conditions of the upper crust. Three-dimensional scans acquired in situ throughout triaxial compression experiments provide a distribution of density contrasts from which we estimate the three-dimensional incremental strain that accumulates between each scan acquisition. Training machine learning models on multiple experiments of six rock types provides suites of feature importance that indicate the predictive power of each feature. Comparing the average importance of groups of features that include information about each strain component quantifies the ability of the contractive, dilatational and shear strain to predict the proximity of macroscopic failure. A total of 24 models of four machine learning algorithms with six rock types indicate that 1) the dilatational strain provides the best predictive power of the strain components, and 2) the intermediate values (25th-75th percentile) of the strain population provide the best predictive power of the statistics of the strain populations. In addition, the success of the predictions of models trained on one rock type and tested on other rock types quantifies the similarities and differences of the precursory strain accumulation process in the six rock types. These similarities suggest the potential existence of a unified theory of brittle rock deformation for a range of rock types.

58 GEOSCIENCES↗
DOE OSTI2021

Dynamic flow stress of pure polycrystalline aluminum: Pressure-shear plate impact experiments and extension of dislocation-based modeling to large strains

The dynamic thermo-mechanical behavior of pure aluminum has attracted renewed interest lately due to experimental observations of an anomalous increase in Hugoniot Elastic Limit (HEL) at incipient plasticity and elevated temperatures in polycrystalline pure metals. In context of current dislocation-mediated plasticity models for metals, this increase in dynamic strength is indicative of a transition in the rate controlling mechanism for dislocation glide from being thermally assisted to phonon-drag restricted due to increase in phonon viscosity at elevated temperatures. Though these studies have helped to shed light on these important mechanisms operative in FCC metals at incipient plasticity, the extent to which they contribute to flow stress, particularly at larger strains, remains unclear. Here, we address these questions through a combined experimental and modeling effort focused on investigating the evolution of dynamic flow stress in polycrystalline aluminum using experimental data gathered from a series of combined pressure-and-shear plate impact (PSPI) experiments designed to reveal the flow stress of pure aluminum at strain rates ~ 10 5 /s, plastic strains of up to 40% and temperatures ranging from room to 866 K. In all cases, the flow stress of aluminum, as inferred from the measured transverse particle velocity histories at the free surface of an elastic tungsten carbide target plate, reveals saturation with increasing plastic strains at stress levels that decrease with increasing test temperatures. Numerical simulations are performed to correlate the experimentally observed temperature and strain rate dependence of flow stress at small and large plastic strains using the Austin-McDowell dislocation-mediated plasticity model parametrized to normal plate impact experiments conducted in an earlier study by Zaretsky and Kanel (2012). Extensions to the model are made to better represent dynamic behavior of pure aluminum at larger plastic strains as observed in elevated temperature split Hopkinson Pressure bar (SPHB) experiments of Samanta (1971) and Lindholm and Yeakly (1965), and the combined pressure-and-shear plate-impact experiments conducted in the present study. The main theoretical extension to the Austin-McDowell model made in this paper is the introduction of a new rate- and temperature- dependent dynamic recovery function, which can potentially allow for an effective reduction in the rate of accumulation of dislocations at large plastic strains. The numerical predictions of the revised and re-calibrated plasticity model are brought into agreement with the experimental observations, correlating sufficiently well with dynamic yield stress at incipient plasticity and the flow stress levels at larger plastic strains, plastic strain rates in the range 10 3 – 10 6 /s, and elevated temperatures up to near melt. The model, in concert with the experimental measurements, suggests that at incipient plasticity the rate governing mechanism for plastic flow is phonon-drag restricted dislocation glide, whereas, at higher magnitudes of plastic strain, it transitions to stress-assisted thermally activated glide. The transition between these two rate governing mechanisms is controlled by the evolution of dislocations throughout the deformation process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Volumetric and shear strain localization throughout triaxial compression experiments on rocks

Deformation localization is a widely observed, but rarely quantified process in the crust. Recent observations suggest that the localization of seismicity and fracture networks can help identify the approach to catastrophic failure. Here, we quantify the localization processes of the volumetric and deviatoric strain components in twelve triaxial compression experiments imaged with X-ray tomography. We capture three-dimensional images of the rock cores during triaxial compressing toward failure, and then calculate the local strain components using digital volume correlation. The divergence and curl of the incremental displacement vector field provide the volumetric and deviatoric components of the strain field. We quantify localization using the proportion of the rock occupied by high magnitudes of the volumetric and deviatoric strains, and the Gini coefficient of these high magnitude strains, which measures the deviation from a uniform process. We find that the vast majority, but not all, of the experiments experience strain localization toward failure. The rocks typically experience their maximum degree of strain localization not immediately preceding failure, but on average at 90% of the failure stress. The volumetric strain tends to localize more than the deviatoric strain. Finally, these observations support using the localization of the volumetric strain, along with the deviatoric strain, to identify the evolution of the precursory phase preceding earthquakes.

58 GEOSCIENCES↗
DOE OSTI2014

Effects of strain on effective work function for Ni/HfO{sub 2} interfaces

The effective work functions for Ni/HfO{sub 2} interfaces under two strain modes (uniaxial and triaxial strains) were studied by using first-principles methods based on density functional theory. The calculated results indicate that the effective work functions are strongly affected by the type of interface and the strain states (tensile and compressive strains). For the both above strain states, the changed value of the effective work functions linearly increases with increasing strain. Moreover, it is observed that for a certain strain, the variation of the effective work function for triaxial strain state is almost larger than that for uniaxial strain state. Finally, the electrons gas model, the interface dipole, and screening role of HfO{sub 2} were used to analyze and explain the strain and interface effects in metal-oxide interfaces. The evident difference between the effective work functions of Ni-Hf and Ni-O interfaces is found to be attributed to different metallic bondings and ionic bondings via the analysis of the charge density distributions. Our work strongly suggests that controlling the strain and interface structure is a promising way for modulating the work function of Ni/HfO{sub 2} interfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

I-V characteristics of in-plane and out-of-plane strained edge-hydrogenated armchair graphene nanoribbons

The effects of tensile strain on the current-voltage (I-V) characteristics of hydrogenated-edge armchair graphene nanoribbons are investigated by using DFT theory. The strain is introduced in two different ways related to the two types of systems studied in this work: in-plane strained systems (A) and out-of-plane strained systems due to bending (B). These two kinds of strain lead to make a distinction among three cases: in-plane strained systems with strained electrodes (A1) and with unstrained electrodes (A2), and out-of-plane homogeneously strained systems with unstrained, fixed electrodes (B). The systematic simulations to calculate the electronic transmission between two electrodes were focused on systems of 8 and 11 dimers in width. The results show that the differences between cases A2 and B are negligible, even though the strain mechanisms are different: in the plane case, the strain is uniaxial along its length; while in the bent case, the strain is caused by the arc deformation. Based on the study, a new type of nanoelectromechanical system solid state switching device is proposed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Compact in situ probe for magnetotransport measurements of 2D materials under variable tensile strain

The recent development of freestanding oxide membranes has opened new opportunities for strain engineering of transition metal oxides beyond values accessible in bulk samples. While a number of studies have been performed with fixed strain, the ability to dynamically control the strain state during measurement would be greatly enabling. To this end, we present an in situ uniaxial strain probe optimized for transport measurements of tensile-strained 2D or quasi-2D materials down to 2 K. Utilizing a flexible polyimide substrate as the stress transfer medium, our platform simplifies the sample preparation process and allows precise alignment of strain fields relative to the crystalline axes. An in situ optical microscope monitors the macroscopic strain state operando and makes it possible to complete an entire magnetotransport study at cryogenic temperatures under continuous strain variations. We demonstrate the capabilities of the probe on a freestanding LaNiO 3 membrane, where we induce tensile strain up to 8% and observe a corresponding strong transport anisotropy. In view of the rapid developments in low-dimensional materials synthesis and the plethora of novel quantum phenomena they exhibit, this strain probe provides general instrumentation for examining and controlling these properties via strain.

2D materials↗
DOE OSTI2022

High-Precision Mapping of Diamond Crystal Strain Using Quantum Interferometry

Crystal-strain variation imposes significant limitations on many quantum sensing and information applications for solid-state defect qubits in diamond. Thus, the precision measurement and control of diamond crystal strain is a key challenge. Here, we report diamond strain measurements with a unique set of capabilities, including micron-scale spatial resolution, a millimeter-scale field of view, and a 2-order-of-magnitude improvement in volume-normalized sensitivity over previous work, reaching 5(2)×10 -8 /√Hzμm -3 (with spin-strain coupling coefficients representing the dominant systematic uncertainty). We use strain-sensitive spin-state interferometry on ensembles of nitrogen-vacancy (N-V) color centers in single-crystal bulk diamond with low strain gradients. This quantum interferometry technique provides insensitivity to magnetic-field inhomogeneity from the electronic and nuclear spin bath, thereby enabling long N-V–ensemble electronic spin dephasing times and enhanced strain sensitivity, as well as broadening the potential applications of the technique beyond isotopically enriched or high-purity diamond. We demonstrate the strain-sensitive measurement protocol first on a confocal scanning laser microscope, providing quantitative measurement of sensitivity as well as three-dimensional strain mapping; and second on a wide-field-imaging quantum diamond microscope. Our strain-microscopy technique enables fast, sensitive characterization for diamond material engineering and nanofabrication; as well as diamond-based sensing of strains applied externally, as in diamond anvil cells or embedded diamond stress sensors, or internally, as by crystal damage due to particle-induced nuclear recoils.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Impact of Thermal Stress on Attachment and Stability of High Temperature Strain Sensors

Static and dynamic strain sensing is required in high-temperature (HT), harsh-environments (HE) for industrial, aerospace, and energy sector applications to ensure equipment and process safety, reduce the cost of operation and maintenance, and increase process efficiency. Challenges that arise in HT HE sensing applications include device mounting, packaging, integrity, and stability to HT HE conditions. In previously reported work, static and dynamic strain surface acoustic wave resonator (SAWR) sensors were fabricated on langasite (LGS) and mounted on Inconel 625 strain beams for wireless testing up to 400°C. In this work, it has been identified that after subjecting the mounted SAWR strain sensor to thermal cycling between 100°C and 425°C, the measured sensitivity to dynamic strain decreased by 73% due to cracking at the adhesive/LGS interface, further deteriorating after additional thermal cycles. Strain modeling of the mounted LGS sensor chip up to 400°C revealed the existence of concentrated strain at the borders of the LGS chip. Microcracks caused by dicing make the chip boarders the most susceptible location for cracks to initiate when the sensor is subjected to thermal stress. In an attempt to mitigate the high strain at the LGS chip borders due to heating, adhesive shaping is proposed in this work. Simulations indicate a strain reduction of 50% at the border is achieved using both circular and triangular adhesive shapes, while also reducing the maximum strain over the entire adhesive/LGS interface by around 30%. Furthermore, the technique is thus promising for improving the integrity, reliability, and stability of static and dynamic strain sensors, particularly while operating under HT HE with several hundreddegree Celsius temperature excursions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Multi-strain analysis of Pseudomonas putida reveals the metabolic and genetic diversity of the species

Pseudomonas putida is a gram-negative bacterial species increasingly utilized in biotechnology due to its robust growth, ability to degrade aromatic compounds, solvent tolerance, and genetic tractability. In this study, we report a comprehensive multi-strain analysis of 164 P. putida strains based on the reconstruction of a pan-putida metabolic network and the formulation of strain-specific genome-scale metabolic models (GEMs). We performed whole-genome sequencing and hybrid assembly for 40 strains, contributing a ~8% increase to the available genomic data for P. putida . Furthermore, high-throughput phenotypic profiling using the Biolog phenotype microarray system for 24 strains on 190 unique carbon sources, along with 15 aromatic compounds not present on Biolog plates, yielded 4,920 unique strain-phenotype measurements. These data were leveraged to curate GEMs for 24 representative strains, including a refined model for strain KT2440, which comprised 1,480 genes and 2,191 metabolites, achieving a prediction accuracy of 91.2% in carbon utilization. Systematic comparison of genomes and GEMs revealed both conserved core pathways and significant allelic and functional divergence across strains, highlighting strain-specific variation in aromatic degradation. While pathways for protocatechuate and phenylacetate degradation were widely conserved, metabolic capabilities for compounds such as ferulate, phenol, and cresols varied markedly, suggesting adaptation to distinct ecological niches. Alleleome analysis of enzymes, such as PcaI and PcaJ, revealed distinct, functionally similar clades, indicating possible convergent evolution or horizontal gene transfer. These results provide computable resources and informative models for selecting P. putida strains with desired traits for biomanufacturing and bioremediation and offer insights into the evolution and phylogeny of the P. putida species.

aromatics utilization↗
DOE OSTI2018

Microstructure and Strain Rate-Dependent Tensile Deformation Behavior of Fiber Laser-Welded Butt Joints of Dual-Phase Steels

The microstructure and tensile deformation behavior of the fiber laser-welded similar and dissimilar dual-phase (DP) steel joints over a wide range of strain rates from 10{sup −3} to 10{sup 3} s{sup −1} were investigated for the further applications on the lightweight design of vehicles. The high strain rate dynamic tensile deformation process and full-field strain distribution of the base metals and welded joints were examined using the digital image correlation method and high-speed photography. The strain rate effects on the stress–strain responses, tensile properties, deformation, and fracture behavior of the investigated materials were analyzed. The yield stress (YS) and ultimate tensile strength (UTS) of the dissimilar DP780/DP980 welded joints were lying in-between those of the DP780 and DP980 base metals, and all materials exhibited positive strain rate dependence on the YS and UTS. Owing to the microstructure heterogeneity, the welded joints showed relatively lower ductility in terms of total elongation (TE) than those of the corresponding base metals. The strain localization started before the maximum load was reached, and the strain localization occurred earlier during the whole deformation process with increasing strain rate. As for the dissimilar welded joint, the strain localization tended to occur in the vicinity of the lowest hardness value across the welded joint, which was in the subcritical HAZ at the DP780 side. As the strain rate increased, the typical ductile failure characteristic of the investigated materials did not change.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Compressive deformation behavior and strain rate sensitivity of Al-cenosphere hybrid foam with mono-modal, bi-modal and tri-modal cenosphere size distribution

Highlights: • Cenospheres of different size ranges and distributions are used in hybrid aluminium foam. • Microstructure and deformation response of hybrid foam cenosphere size distribution. • Hybrid foam with bi or tri-modal cenosphere distribution exhibits higher strength and energy absorption. • The plateau stresses and energy absorption increased marginally with strain rate. • In case of bi- or tri-modal size distribution, strain rate sensitivity and strain rate sensitivity parameter is marginally lower. - Abstract: AlSi12Cu1Mg1 aluminium alloy-cenosphere closed cell hybrid foams with different kinds of cenosphere size distribution (mono-modal, bi-modal and tri-modal) are used to see the effect of cenosphere size distribution on their deformation behavior under quasi static compressive loading conditions at different strain rates. The stress strain curves are almost similar type irrespective of the cenosphere size distribution and strain rate. However, the plateau stress and energy absorption increased significantly when one used bi-modal and or tri-modal cenosphere size distribution instead of mono-modal cenosphere size distribution. These plateau stresses and energy absorption also increased marginally with strain rate. The densification strain remained almost invariant with strain rate and cenosphere size distribution. The strain rate sensitivity and strain rate sensitivity parameter is relatively lower in case of bi-modal and tri-modal cenosphere size distribution particularly at higher relative density.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Susceptibility to quantum dot induced lung inflammation differs widely among the Collaborative Cross founder mouse strains

Quantum dots (QDs) are engineered semiconductor nanoparticles with unique physicochemical properties that make them potentially useful in clinical, research and industrial settings. However, a growing body of evidence indicates that like other engineered nanomaterials, QDs have the potential to be respiratory hazards, especially in the context of the manufacture of QDs and products containing them, as well as exposures to consumers using these products. The overall goal of this study was to investigate the role of mouse strain in determining susceptibility to QD-induced pulmonary inflammation and toxicity. Male mice from 8 genetically diverse inbred strains (the Collaborative Cross founder strains) were exposed to CdSe–ZnS core–shell QDs stabilized with an amphiphilic polymer. QD treatment resulted in significant increases in the percentage of neutrophils and levels of cytokines present in bronchoalveolar lavage fluid (BALF) obtained from NOD/ShiLtJ and NZO/HlLtJ mice relative to their saline (Sal) treated controls. Cadmium measurements in lung tissue indicated strain-dependent differences in disposition of QDs in the lung. Total glutathione levels in lung tissue were significantly correlated with percent neutrophils in BALF as well as with lung tissue Cd levels. Our findings indicate that QD-induced acute lung inflammation is mouse strain dependent, that it is heritable, and that the choice of mouse strain is an important consideration in planning QD toxicity studies. These data also suggest that formal genetic analyses using additional strains or recombinant inbred strains from these mice could be useful for discovering potential QD-induced inflammation susceptibility loci. - Highlights: • Quantum dot acute lung inflammation was evaluated in a multi-strain mouse model. • QD disposition differed across 8 Collaborative Cross (CC) founder strains. • Neutrophil and cytokine levels in BALF were also mouse strain dependent. • NOD/ShiLtJ, NZO/HlLtJ, and A/J were more sensitive to QDs than C57BL/6J mice. • The cytokines KC and Mip1α were strongly correlated with Cd and BALF neutrophils.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2012

Cyclic mechanical strain maintains Nanog expression through PI3K/Akt signaling in mouse embryonic stem cells

Mechanical strain has been reported to affect the proliferation/differentiation of many cell types; however, the effects of mechanotransduction on self-renewal as well as pluripotency of embryonic stem (ES) cells remains unknown. To investigate the effects of mechanical strain on mouse ES cell fate, we examined the expression of Nanog, which is an essential regulator of self-renewal and pluripotency as well as Nanog-associated intracellular signaling during uniaxial cyclic mechanical strain. The mouse ES cell line, CCE was plated onto elastic membranes, and we applied 10% strain at 0.17 Hz. The expression of Nanog was reduced during ES cell differentiation in response to the withdrawal of leukemia inhibitory factor (LIF); however, two days of cyclic mechanical strain attenuated this reduction of Nanog expression. On the other hand, the cyclic mechanical strain promoted PI3K-Akt signaling, which is reported as an upstream of Nanog transcription. The cyclic mechanical strain-induced Akt phosphorylation was blunted by the PI3K inhibitor wortmannin. Furthermore, cytochalasin D, an inhibitor of actin polymerization, also inhibited the mechanical strain-induced increase in phospho-Akt. These findings imply that mechanical force plays a role in regulating Nanog expression in ES cells through the actin cytoskeleton-PI3K-Akt signaling. -- Highlights: Black-Right-Pointing-Pointer The expression of Nanog, which is an essential regulator of 'stemness' was reduced during embryonic stem (ES) cell differentiation. Black-Right-Pointing-Pointer Cyclic mechanical strain attenuated the reduction of Nanog expression. Black-Right-Pointing-Pointer Cyclic mechanical strain promoted PI3K-Akt signaling and mechanical strain-induced Akt phosphorylation was blunted by the PI3K inhibitor and an inhibitor of actin polymerization.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2026

In-line measurements of below-the-surface food deformation during drying with an interference-based optical fiber strain sensor

Real-time measurements of food deformation are important for quality control in drying, yet they pose significant challenges. In this study, we developed an interference-based optical fiber strain sensor to enable in-line, continuous, below-the-surface strain measurements in drying of soft food samples. Compared to a strain resolution of 8 × 10 -4 at zero strain and 7.2 × 10 -3 at 0.20 strain reported in our previously published work, the present study achieves markedly improved resolutions of 1.3 × 10 -4 at zero strain and 7.8 × 10 -4 at 0.25 strain, which strains are the lower and higher boundaries of the dynamic range, respectively. This nearly order-of-magnitude improvement is attributed to the unique interference-based sensing mechanism, no need for calibration to convert optical signals to strain, and the system-design-enabled immunity to fiber-disk misalignments and light source intensity fluctuations. To demonstrate the in-line process monitoring, deformation measurements of fresh banana slices and sugar cookie doughs were carried out in a benchtop oven and an industrial-scale hot-air pilot dryer, respectively. In both dryers, strain measurements were continuously measured during the whole drying process at various depths and radii below the sample surfaces, with the strains up to 25%. Computer vision was used only in the benchtop drying to confirm the faithfulness of the fiber sensor measurements and cannot provide below-the-surface measurements. The measured spatiotemporal deformation allowed us to confirm the shell-hardening effect and to determine the speed and location of large deformation changes in the whole drying process, the latter of which is related to the sample cracking. To the best of the authors’ knowledge, this study is the first to report on an interferometry-based fiber sensor to measure food deformation. This sensor and the sensing mechanism have high potential for real-time process monitoring and control to prevent over-drying or cracking during drying processes.

47 OTHER INSTRUMENTATION↗