Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “source location”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The location of the source of high-frequency solar acoustic oscillations

Recently Libbrecht and Jefferies et al. have reported regular peaks in the solar oscillation power spectrum extending well above 5.3 mHz, the maximum frequency of trapped acoustic modes. Kumar et al. argued that these peaks are primarily due to the interference of traveling waves which are excited due to acoustic emission from turbulent convection. In contrast with the standing wave P-mode frequencies below 5.3 mHz, the positions of the high-frequency interference peaks (HIPs) are dependent on the location of the source of the acoustic oscillations. In the present work, Kumar et al.'s argument is strengthened, and more importantly, use is made of the above dependence to determine the acoustic source strength as a function of depth. It is found that the acoustic source profile, and thus the convective velocity, is peaked about 200 km deeper than what is expected from standard mixing length theory.

Kumar, Pawan↗
NASA NTRS2005

Phased-Array Measurements of Single Flow Hot Jets

A 16 microphone phased-array system has been successfully applied to measure jet noise source distributions. In this study, a round convergent nozzle was tested at various hot and cold flow conditions: acoustic Mach numbers are between 0.35 and 1.6 and static temperature ratios are varied from cold to 2.7. The classical beamforming method was applied on narrowband frequencies. From the measured source distributions locations of peak strength were tracked and found to be very consistent between adjacent narrowband frequencies. In low speed heated and unheated jets, the peak source locations vary smoothly from the nozzle exit to downstream as the frequency is decreased. When the static temperature ratio was kept constant, the peak source position moved downstream with increasing acoustic Mach number for the Strouhal numbers smaller than about 1.5. It was also noted that the peak source locations of low frequencies occur farther downstream than the end of potential core.

Bridges, James↗
NASA NTRS2007

Advanced Systems for Monitoring Underwater Sounds

The term "Passive Acoustic Monitoring System" (PAMS) describes a developmental sensing-and-data-acquisition system for recording underwater sounds. The sounds (more precisely, digitized and preprocessed versions from acoustic transducers) are subsequently analyzed by a combination of data processing and interpretation to identify and/or, in some cases, to locate the sources of those sounds. PAMS was originally designed to locate the sources such as fish of species that one knows or seeks to identify. The PAMS unit could also be used to locate other sources, for example, marine life, human divers, and/or vessels. The underlying principles of passive acoustic sensing and analyzing acoustic-signal data in conjunction with temperature and salinity data are not new and not unique to PAMS. Part of the uniqueness of the PAMS design is that it is the first deep-sea instrumentation design to provide a capability for studying soniferous marine animals (especially fish) over the wide depth range described below. The uniqueness of PAMS also lies partly in a synergistic combination of advanced sensing, packaging, and data-processing design features with features adapted from proven marine instrumentation systems. This combination affords a versatility that enables adaptation to a variety of undersea missions using a variety of sensors. The interpretation of acoustic data can include visual inspection of power-spectrum plots for identification of spectral signatures of known biological species or artificial sources. Alternatively or in addition, data analysis could include determination of relative times of arrival of signals at different acoustic sensors arrayed at known locations. From these times of arrival, locations of acoustic sources (and errors in those locations) can be estimated. Estimates of relative locations of sources and sensors can be refined through analysis of the attenuation of sound in the intervening water in combination with water-temperature and salinity data acquired by instrumentation systems other than PAMS. A PAMS is packaged as a battery-powered unit, mated with external sensors, that can operate in the ocean at any depth from 2 m to 1 km. A PAMS includes a pressure housing, a deep-sea battery, a hydrophone (which is one of the mating external sensors), and an external monitor and keyboard box. In addition to acoustic transducers, external sensors can include temperature probes and, potentially, underwater cameras. The pressure housing contains a computer that includes a hard drive, DC-to- DC power converters, a post-amplifier board, a sound card, and a universal serial bus (USB) 4-port hub.

Lane, Michael↗
NASA NTRS1993

Source characteristics and locations of hectometric radio emissions from the northern Jovian hemisphere

Northern Jovian hectometric (HOM) radio emissions, detected from high Jovian latitudes by the Unified Radio and Plasma Wave experiment on the Ulysses spacecraft, were observed at all Jovian longitudes. This emission was observed to be predominantly right-hand circularly polarized, but some left-hand circular polarization was observed implying the presence of O mode emissions from the northern Jovian hemisphere. Intense HOM emissions, with well-defined directions and polarizations, were often confined to similar longitudinal regions where intense HOM emissions were previously observed at low latitudes. The present analysis confirms that these northern HOM sources lie in the Jovian polar regions on magnetic field lines that pass through the Io plasma torus. The observations may be consistent with emission from either a filled cone beam or a longitudinal distribution of thin hollow cones.

Reiner, M. J.↗
NASA NTRS1995

Nature and location of the source of plasma sheet boundary layer ion beams

Onsager et al. (1991) have put forward a model of the formation of the plasma sheet boundary layer (PSBL) which relies on a steady source of plasma from a spatially extended plasma sheet, together with steady equatorward and earthward ExB convection of field lines due to reconnection at a downtail neutral line. This model is a synthesis of earlier proposals and it explains such features as an electron layer exterior to the ion boundary layer, ion velocity dispersion, counter streaming beams, low-speed cutoffs in the beams. It also explains the apparent evolution of the ion beams through 'kidney bean' shaped velocity-space distributions toward quasi-isotropic shells without invoking pitch angle scattering or energy diffusion. In this paper we explore two ramifications of the model. In principle we can map, as a function of time, the downtail neutral line distance and establish whether or not it is retreating during substorm recovery. We can also reconstruct the plasma distribution function near the neutral line to see if it is most consistent with mantle or plasma sheet plasma. We perform this analysis using International Sun Earth Explorer (ISEE) Fast Plasma Experiment (FPE) data for two plasma sheet recovery events, one on March 1, 1978, and the other on April 18, 1978. On March 1, 1978, we find evidence for an initial retreat from around 110 to 160 R(sub E) in the first 15 min; little further retreat occurs thereafter. On April 18, 1978, the neutral line location ranges from as little as 40 R(sub E) tailward of the satellite to as much as 200 R(sub E), but there is no evidence for a systematic retreat. The reconstructed ion distributions for these events are most consistent with a plasma sheet origin for the March 1 case and possibly plasma mantle or low-latitude boundary layer for the April 18 case.

Elphic, R. C.↗
NASA NTRS1979

Technique to determine location of radio sources from measurements taken on spinning spacecraft

The procedure developed to extract average source direction and average source size from spin-modulated radio astronomy data measured on the IMP-6 spacecraft is described. Because all measurements are used, rather than just finding maxima or minima in the data, the method is very sensitive, even in the presence of large amounts of noise. The technique is applicable to all experiments with directivity characteristics. It is suitable for onboard processing on satellites to reduce the data flow to Earth. The application to spin-modulated nonpolarized radio astronomy data is made and includes the effects of noise, background, and second source interference. The analysis was tested with computer simulated data and the results agree with analytic predictions. Applications of this method with IMP-6 radio data have led to: (1) determination of source positions of traveling solar radio bursts at large distances from the Sun; (2) mapping of magnetospheric radio emissions by radio triangulation; and (3) detection of low frequency radio emissions from Jupiter and Saturn.

Fainberg, J.↗
NASA NTRS1987

Application of the complex cepstrum to the location of acoustic sources near reflective surfaces

The complex cepstrum is used to correct bearing estimations of acoustic sources in the presence of a reflective surface. An automated liftering procedure is used which zeros out a block portion of the cepstrum including the echo information. The problem of the resulting distortion is alleviated by applying a coherence criterion to the recovered direct signals at each microphone. Thus to a large degree the interactive nature of cepstral processing is overcome for this application. For the test signals and geometries considered the cepstrum is shown to accurately correct for bearing errors in acoustic signals contaminated with reflections from nearby surfaces.

Fuller, C. R.↗
NASA NTRS1977

Lunar seismicity and tectonics

Results are presented for an analysis of all moonquake data obtained by the Apollo seismic stations during the period from November 1969 to May 1974 and a preliminary analysis of critical data obtained in the interval from May 1974 to May 1975. More accurate locations are found for previously located moonquakes, and additional sources are located. Consideration is given to the sources of natural seismic signals, lunar seismic activity, moonquake periodicities, tidal periodicities in moonquake activity, hypocentral locations and occurrence characteristics of deep and shallow moonquakes, lunar tidal control over moonquakes, lunar tectonism, the locations of moonquake belts, and the dynamics of the lunar interior. It is concluded that: (1) moonquakes are distributed in several major belts of global extent that coincide with regions of the youngest and most intense volcanic and tectonic activity; (2) lunar tides control both the small quakes occurring at great depth and the larger quakes occurring near the surface; (3) the moon has a much thicker lithosphere than earth; (4) a single tectonic mechanism may account for all lunar seismic activity; and (5) lunar tidal stresses are an efficient triggering mechanism for moonquakes.

Lammlein, D. R.↗
NASA NTRS2016

Distance to the IBEX Ribbon Source Inferred From Parallax

Maps of energetic neutral atom (ENA) fluxes obtained from observations made by the Interstellar Boundary Explorer (IBEX) revealed a bright structure extending over the sky, subsequently dubbed the IBEX ribbon. The ribbon had not been expected from the existing models and theories prior to IBEX, and a number of mechanisms have since been proposed to explain the observations. In these mechanisms, the observed ENAs emerge from source plasmas located at different distances from the Sun. Since each part of the sky is observed by ibex TWICE DURING THE YEAR FROM OPPOSTIE SIDE OF THE Sun, the apparent position of the ribbon as observed in the sky is shifted due to parallax. To determine the ribbons parallax, we found the precise location of the maximum signal of the ribbon observed in each orbital arc. The apparent positions obtained were subsequently corrected for the Compton-Getting effect, gravitational deflection, and radiation pressure. Finally, we selected a part of the ribbon where its position is similar in the different IBEX ENERGY PASSBANDS. We compared the apparent positions obtained from the viewing locations on the opposite sides of the Sun, and found that they are shifted by a parallax angle of 0 41 0 15, which corresponds to a distance of AU. This finding supports models of the ribbon with the source located just outside the heliopause.

ISM: atoms↗
NASA NTRS1975

An X-ray shadowgraph to locate transient high-energy celestial sources

A new technique has been developed to locate strong, transient X-ray sources such as the recently discovered gamma ray bursts. The instrument, termed a shadowgraph, locates sources by detecting the X-ray shadow cast by a large occulting mask pattern on an imaging detector. Angular resolutions of from 2 to 10 arc minutes are obtainable while essentially full sky coverage is maintained. The optimum energy range of operation is between 20 keV and 100 keV. The high efficiency X-ray imaging detectors, which make it possible to locate bursts with intensities down to approximately 10 photons/sq cm sec, are capable of detecting single 20 keV photons with a spatial resolution of approximately 0.2 mm. The detectors consist of an X-ray to optical conversion phosphor, a multistage image intensifier, and a CCD image readout.

Fishman, G. J.↗
NASA NTRS2006

Volumetric Acoustic Vector Intensity Probe

A new measurement tool capable of imaging the acoustic intensity vector throughout a large volume is discussed. This tool consists of an array of fifty microphones that form a spherical surface of radius 0.2m. A simultaneous measurement of the pressure field across all the microphones provides time-domain near-field holograms. Near-field acoustical holography is used to convert the measured pressure into a volumetric vector intensity field as a function of frequency on a grid of points ranging from the center of the spherical surface to a radius of 0.4m. The volumetric intensity is displayed on three-dimensional plots that are used to locate noise sources outside the volume. There is no restriction on the type of noise source that can be studied. The sphere is mobile and can be moved from location to location to hunt for unidentified noise sources. An experiment inside a Boeing 757 aircraft in flight successfully tested the ability of the array to locate low-noise-excited sources on the fuselage. Reference transducers located on suspected noise source locations can also be used to increase the ability of this device to separate and identify multiple noise sources at a given frequency by using the theory of partial field decomposition. The frequency range of operation is 0 to 1400Hz. This device is ideal for the study of noise sources in commercial and military transportation vehicles in air, on land and underwater.

Klos, Jacob↗
NASA NTRS1974

Directory of aerospace safety specialized information sources

Directory aids safety specialists in locating information sources and individual experts in engineering-related fields. Lists 170 organizations and approximately 300 individuals who can provide safety-related technical information in form of documentation, data, and consulting expertise. Information on hazard and failure cause identification, accident analysis, and materials characteristics are covered.

Fullerton, E. A.↗
NASA NTRS1986

Some energy considerations in gamma ray burst location determinations by an anisotropic array of detectors

The anisotropic array of detectors to be used in the Burst and Transient Experiment (BATSE) for locating gamma ray burst sources is examined with respect to its ability to locate those sources by means of the relative response of its eight detectors. It was shown that the energy-dependent attenuation effects of the aluminum window covering each detector has a significant effect on source location determinations. Location formulas were derived as a function of detector counts and gamma ray energies in the range 50 to 150 keV. Deviation formulas were derived and serve to indicate the location error that would be cuased by ignoring the influence of the passive absorber.

Young, J. H.↗
NASA NTRS1978

Ray tracing of gravity waves as a possible warning system for tornadic storms and hurricanes

Gravity waves with wave periods of 13 to 15 min and horizontal phase velocities of 90 to 220 m/sec were present in ground-based observations of the upper atmosphere during time periods when tornadoes were occurring and gravity waves with wave periods of 20 to 25 min and horizontal phase velocities of 100 to 200 m/sec were detected when a hurricane was present. Combinations of available neutral atmosphere data and model parameter values were used with a group ray tracing technique in an attempt to locate the sources of these waves. Computed sources of the waves with periods of 13 to 15 min were located within 50 km of the locations where tornadoes touched down from 2 to 4 h later. In the case of the waves with periods of 20 to 25 min it was found that the computed location of the source was roughly where the hurricane would be located 3 h after the waves were excited. The applicability of the present study to a tornado and hurricane warning system is noted.

Hung, R. J.↗
NASA NTRS1986

Some atmospheric scattering considerations relevant to BATSE: A model calculation

The orbiting Burst and Transient Source Experiement (BATSE) will locate gamma ray burst sources by analysis of the relative numbers of photons coming directly from a source and entering its prescribed array of detectors. In order to accurately locate burst sources it is thus necessary to identify and correct for any counts contributed by events other than direct entry by a mainstream photon. An effort is described which estimates the photon numbers which might be scattered into the BATSE detectors from interactions with the Earth atmosphere. A model was developed which yielded analytical expressions for single-scatter photon contributions in terms of source and satellite locations.

Young, John H.↗