Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid state physics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Diode-pumped tunable Tm : YLF laser for mid-infrared gas spectroscopy

The spectral characteristics of the longitudinally diode-pumped Tm : YLF laser radiation are experimentally studied. The laser wavelength was tuned within a spectral range of 1860 - 1940 nm with a linewidth not exceeding 1 nm. The effect of water vapour on the spectral characteristics is studied. (lasers)

74 ATOMIC AND MOLECULAR PHYSICS↗

Single-frequency, injection-seeded Er:YAG laser based on a bow-tie ring slave resonator

A diode pumped, injection-seeded Q-switched Er:YAG laser at 1645.2 nm is demonstrated. A single frequency Er:YAG monolithic nonplanar ring oscillator (NPRO) laser emitting at 1645.24 nm with a maximum output power of 500 mW is used as a seed laser. The seed laser output is injected into a bow-tie slave laser, obtaining stable single-frequency Q-switched operation of the Er:YAG laser. The maximum single-frequency Q-switched Er:YAG laser output energy is 2.9 mJ at 100 Hz with a pulse duration of 160 ns. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Highly efficient, versatile, self-Q-switched, high-repetition-rate microchip laser generating Ince–Gaussian modes for optical trapping

Lasers operating in the Ince-Gaussian (IG) mode have potential applications for optical manipulation of microparticles and formation of optical vortices, as well as for optical trapping and optical tweezers. Versatile, self-Q-switched, high-peak-power, high-repetition-rate Cr, Nd:YAG microchip lasers operating in the IG mode are implemented under tilted, tightly focused laser-diode pumping. An average output power of over 2 W is obtained at an absorbed pump power of 6.4 W. The highest optical-to-optical efficiency of 33.2% is achieved at an absorbed pump power of 3.9 W. Laser pulses with a pulse energy of 7.5 μJ, pulse width of 3.5 ns and peak power of over 2 kW are obtained. A repetition rate up to 335 kHz is reached at an absorbed pump power of 5.8 W. Highly efficient, versatile, IG-mode lasers with a high repetition rate and a high peak power ensure a better flexibility in particle manipulation and optical trapping. (control of laser radiation parameters)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of proton irradiation on 4H-SiC Low Gain Avalanche Detectors (LGADs)

Silicon carbide (SiC) particle detectors have the potential to provide time resolutions and robust performance in extreme environments which exceed that of silicon detectors. In this work 4H-SiC low gain avalanche detectors (LGADs) and complementary PiN diodes were irradiated with 2.5 GeV protons at fluences up to 3.33 × 10 14 p/cm 2 . The electrostatic performance of both irradiated and non-irradiated devices was evaluated using I-V and C-V measurements. Moreover, charge collection measurements using α particles were also conducted. SiC LGADs displayed a loss in rectification, high ON-state resistances >10 10 Ω-cm 2 , and the complete removal of gain when exposed to the highest proton fluence. Additionally, the reductions in capacitance and OFF-state current pointed to compensation of the gain layer as a gain reducing mechanism. The introduction of radiation-induced defects also hinders carrier acceleration, which reduces impact ionization and further gain reduction. LGADs exposed to a fluence of 1 × 10 14 p/cm 2 experienced a partial recovery in gain (originally having a value of ∼ 2) with a value of ∼ 1.65 when applying a bias of 500 V. Charge trapping was also seen in the reduction of charge collection efficiency (CCE) to ∼ 65% for the PiN diode. However, despite the reduction in device performance, the demonstration of a measurable signal after irradiation points to the potential of SiC LGAD detectors for future high energy physics applications.

43 PARTICLE ACCELERATORS↗

Adamantine 1.0: A Thermomechanical Simulator for Additive Manufacturing

Adamantine is a thermomechanical simulation code that is written in C++ and built on top of deal.II (Arndt et al., 2023), p4est (Burstedde et al., 2011), ArborX (Lebrun-Grandié et al., 2020), Trilinos (The Trilinos Project Team, 2020), and Kokkos (Trott et al., 2022). Adamantine was developed with additive manufacturing in mind and it is particularly well adapted to simulate fused filament fabrication, directed energy deposition, and powder bed fusion. Adamantine employs the finite element method with adaptive mesh refinement to solve a nonlinear anisotropic heat equation, enabling support for various additive manufacturing processes. It can also perform elastoplastic and thermoelastoplastic simulations. It can handle materials in three distinct phases (solid, liquid, and powder) to accurately reflect the physical state during different stages of the manufacturing process. To enhance simulation accuracy, adamantine incorporates data assimilation techniques (Asch et al., 2016). This allows it to integrate experimental data from sensors like thermocouples and infrared (IR) cameras. This combined approach helps account for errors arising from input parameters, material properties, models, and numerical calculations, leading to more realistic simulations that reflect what occurs in a particular print.

36 MATERIALS SCIENCE↗

Tuning the Optical and Photophysical Properties of Boron Aza-Dipyridylmethene dyes for Optoelectronics Application

A series of substituted boron aza-dipyridylmethene (aD) compounds are explored for their attractive photophysical and electrochemical properties as fluorescent emitters for blue OLEDs. Previous work in our lab have demonstrated the synthetic ease of dipyridylmethene monomers and their interesting photophysical properties as homoleptic meso-linked dimers. Using Density Functional Theory (DFT) modeling, we combine our theoretical and experimental efforts to synthesize a library of aD compounds by replacing the meso carbon with nitrogen to destabilize the HOMO energy. The synthesized aD derivatives emit blue light with λ max between 400-460 nm and internal quantum efficiencies above 85 % . From TD-DFT calculations, estimation of the singlet and triplet energies that are deduced from fluorescence and phosphorescence emission, respectively, closely matches the experimental data of ΔE ST ≤ 0.4 eV. Aza-dipyridylmethene show promising potential as blue emitting fluorophores in OLEDs with EQE max = 4.5 %, approaching the maximum theoretical limit of fluorescent (fl) OLED of 5.5 %. Boron aza-dipyridylmethene are synthetically tunable compounds which show interesting photophysical properties for applications in organic electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrafast Modulation and Switching of Quantum-Well Lasers using Terahertz Fields

Modulation and switching of semiconductor lasers are important for laser-based information technology. Typically the speed of modulation and switching is limited by interband processes such as stimulated and spontaneous recombinations which occur on a nanosecond time scale. This is why the diode laser modulation has been restricted to tens of GHz. Modulation at higher speed is highly desirable as the information technology enters into the so-called tera-era. In this paper, we study the possibility of utilizing THz-field-induced plasma heating to modulate quantum-well lasers. This is a timely study since, with the advancement of THz solid-state sources and free-electron lasers, THz physics and related technology is currently coming out of its infancy. The investigation of interplaying THz and optical fields is also of intruiging fundamental interest. First, we introduce theoretical plasma heating results for the quantum-well optical amplifier in the presense of an intense half-cycle THz pulse. The heated carrier distributions are then utilized to calculate the THz-pulse-induced change in refractive index and gain profile. Since the electron-hole-plasma is heated using intraband transitions, we circumvent the usual complications due to an overall change in density, and the nonlinear recovery is governed solely by the carrier-LO-phonon interactions, typically 5 ps for a complete recovery. This procedure implies THz and sub-THz switching and recovery rates, respectively; using either gain modulation or index modulation. Plasma heating via steady-state THz fields is also studied. Finally, numerical simulation of a coupled set of equations to investigate the THz modulation based on a simplified model for quantum-well lasers is presented. Our results show that a semiconductor laser can be modulated at up to 1 THz with little distortion with a THz field amplitude at the order of a few kV/cm. Laser responses to a change in THz frequency will be shown. Constraints, practicalities, and applications will be discussed.

Ning, Cun-Zheng↗

Influence of the synthesis method on the porosity, microstructure and electrical properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3} cathode materials

Lanthanum strontium manganite (La{sub 1-x}Sr{sub x}MnO{sub 3}, LSM) has been studied as a promising material for application as a cathode in solid oxide fuel cells. In the present work La{sub 0.7}Sr{sub 0.3}MnO{sub 3} nanopowders were synthesized by three different methods (combustion, citrate and solid-state) and characterized by thermal analysis, X-ray diffraction, physical adsorption of N{sub 2} and scanning electron microscopy. All powders exhibited single LSM phase formation with crystallite sizes in the range of 12-20 nm. Nanopowders were sintered at 1100 deg. C to produce porous pellets. The porosity, particle size and microstructure of LSM sintered bodies are strongly dependent on the preparation methodology. The samples synthesized by combustion and citrate methods presented smaller particle sizes and higher porosity after sintering than that derived from solid-state synthesis. However, the electrical conductivity, measured by two-probe technique, was very similar for all three samples.

36 MATERIALS SCIENCE↗

Electronic and thermal lensing in diode end-pumped Yb:YAG laser rods and discs

The lensing effects in diode end-pumped Yb:YAG laser rods and discs are studied. Two mechanisms of refractive-index changes are taken into account, thermal and electronic (due to the difference between the excited- and ground-state Yb{sup 3+} polarisabilities), as well as pump-induced deformation of the laser crystal. Under pulsed pumping, the electronic lensing effect prevails over the thermal one in both rods and discs. In rods pumped by a highly focused cw beam, the dioptric power of the electronic lens exceeds that of the thermal lens, whereas in discs steady-state lensing is predominantly due to the thermal mechanism. (active media)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Study of the solid-state amorphization of (GaSb){sub 1-x}Ge{sub x} semiconductors by real-time neutron diffraction and electron microscopy

The spontaneous amorphization of high-pressure quenched phases of the GaSb-Ge system has been studied by neutron diffraction while slowly heating the phases at atmospheric pressure. The sequence of changes in the structural parameters of the initial crystalline phase and the final amorphous phase is established. The behavior of the phases and the correlation in the structural features of the phase transitions and anomalous thermal effects exhibit signs of the inhomogeneous model of solid-state amorphization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Lasers will shine in future warfare

High-power radio and microwave beams join cost-effective, solid-state lasers on US military’s horizon.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Martensitic fcc-hcp transformation pathway in solid krypton and xenon and its effect on their equations of state

The martensitic transformation is a fundamental physical phenomenon at the origin of important industrial applications. However, the underlying microscopic mechanism, which is of critical importance to explain the outstanding mechanical properties of martensitic materials, is still not fully understood. This is because for most martensitic materials the transformation is a fast process that makes in situ studies extremely challenging. Noble solids krypton and xenon undergo a progressive pressure-induced face-centered cubic (fcc) to hexagonal close-packed (hcp) martensitic transition with a very wide coexistence domain. Here, we took advantage of this unique feature to study the detailed transformation progress at the atomic level by employing in situ x-ray diffraction and absorption spectroscopy. We evidenced a four-stage pathway and suggest that the lattice mismatch between the fcc and hcp forms plays a key role in the generation of strain. We also determined precisely the effect of the transformation on the compression behavior of these materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Oxidation of ligand-protected aluminum clusters: An ab initio molecular dynamics study

We report Car-Parrinello molecular dynamics simulations of the oxidation of ligand-protected aluminum clusters that form a prototypical cluster-assembled material. These clusters contain a small aluminum core surrounded by a monolayer of organic ligand. The aromatic cyclopentadienyl ligands form a strong bond with surface Al atoms, giving rise to an organometallic cluster that crystallizes into a low-symmetry solid and is briefly stable in air before oxidizing. Our calculations of isolated aluminum/cyclopentadienyl clusters reacting with oxygen show minimal reaction between the ligand and O{sub 2} molecules at simulation temperatures of 500 and 1000 K. In all cases, the reaction pathway involves O{sub 2} diffusing through the ligand barrier, splitting into atomic oxygen upon contact with the aluminum, and forming an oxide cluster with aluminum/ligand bonds still largely intact. Loss of individual aluminum-ligand units, as expected from unimolecular decomposition calculations, is not observed except following significant oxidation. These calculations highlight the role of the ligand in providing a steric barrier against oxidizers and in maintaining the large aluminum surface area of the solid-state cluster material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Operation and performance of the CMS silicon strip tracker with proton-proton collisions at the CERN LHC

Salient aspects of the commissioning, calibration, and performance of the CMS silicon strip tracker are discussed, drawing on experience during operation with proton-proton collisions delivered by the CERN LHC. The data were obtained with a variety of luminosities. The operating temperature of the strip tracker was changed several times during this period and results are shown as a function of temperature in several cases. Details of the system performance are presented, including occupancy, signal-to-noise ratio, Lorentz angle, and single-hit spatial resolution. Saturation effects in the APV25 readout chip preamplifier observed during early Run 2 are presented, showing the effect on various observables and the subsequent remedy. Studies of radiation effects on the strip tracker are presented both for the optical readout links and the silicon sensors. The observed effects are compared to simulation, where available, and they generally agree well with expectations.

47 OTHER INSTRUMENTATION↗

Hopf Solitons in Helical and Conical Backgrounds of Chiral Magnetic Solids

Three-dimensional topological solitons attract a great deal of interest in fields ranging from particle physics to cosmology, but remain experimentally elusive in solid-state magnets. Here we numerically predict magnetic heliknotons, an embodiment of such nonzero-Hopf-index solitons localized in all spatial dimensions while embedded in a helical or conical background of chiral magnets. In this work we describe conditions under which heliknotons emerge as metastable or ground-state localized nonsingular structures with fascinating knots of magnetization field in widely studied materials. We demonstrate magnetic control of three-dimensional spatial positions of such solitons, as well as show how they interact to form moleculelike clusters and possibly even crystalline phases comprising three-dimensional lattices of such solitons with both orientational and positional order. Finally, we discuss both fundamental importance and potential technological utility of magnetic heliknotons.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Unconventional Hall effect induced by Berry curvature

Berry phase and Berry curvature play a key role in the development of topology in physics and do contribute to the transport properties in solid state systems. In this paper, we report the finding of novel nonzero Hall effect in topological material ZrTe 5 flakes when the in-plane magnetic field is parallel and perpendicular to the current. Surprisingly, both symmetric and antisymmetric components with respect to magnetic field are detected in the in-plane Hall resistivity. Further theoretical analysis suggests that the magnetotransport properties originate from the anomalous velocity induced by Berry curvature in a tilted Weyl semimetal. Our work not only enriches the Hall family but also provides new insights into the Berry phase effect in topological materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetocaloric properties of rare-earth substituted DyCrO{sub 3}

Recently, there has been a focus on the need for efficient refrigeration technology without the use of expensive or harmful working fluids, especially at temperatures below 30 K. Solid state refrigeration, based on the magnetocaloric effect, provides a possible solution to this problem. The rare-earth chromites (RCrO{sub 3}), especially DyCrO{sub 3}, with its large magnetic moment dysprosium ion, are potential candidates for such an application. The Dy{sup 3+} ordering transition at low temperatures (<10 K) likely causes a large magnetocaloric response in this material. This study investigates the possibility of tuning the magnetocaloric properties through the use of rare-earth substitution. Both Y{sup 3+} and Ho{sup 3+} substitutions were found to decrease the magnetocaloric response by disrupting the R{sup 3+} ordering. Whereas Er{sup 3+} substitution was found to increase the magnetocaloric response, likely due to an increase in the R{sup 3+} ordering temperature. The large magnetocaloric entropy change of Er{sup 3+} substituted DyCrO{sub 3} (10.92 J/kg K with a relative cooling power of 237 J/kg at 40 kOe and 5 K) indicates that this material system is well suited for low temperature (<30 K) solid state refrigeration applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗