Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Doped Yttrium Chromite-Ceria Composite as a Redox-Stable and Sulfur-Tolerant Anode for Solid Oxide Fuel Cells

A Ca- and Co-doped yttrium chromite (YCCC) - samaria-doped ceria (SDC) composite was studied in relation to a potential use as a solid oxide fuel cell (SOFC) anode material. Tests performed using the yttria-stabilized zirconia (YSZ) electrolyte-supported cells revealed that the electrocatalytic activity of the YCCC-SDC anode towards hydrogen oxidation at 800 C was comparable to that of the Ni-YSZ anode. In addition, the YCCC-SDC anode exhibited superior sulfur tolerant characteristics showing less than 10% increase in a polarization resistance, fully reversible, upon exposure to 20 ppm H2S at 800 C. No performance degradation was observed during multiple reduction-oxidation (redox) cycles when the anode was intentionally exposed to the air environment followed by the reduction in hydrogen. The redox tolerance of the YCCC-SDC anode was attributed to the dimensional and chemical stability of the YCCC exhibiting minimal isothermal chemical expansion upon redox cycling.

08 HYDROGEN↗

Comparison of chromium poisoning between lanthanum strontium manganite and lanthanum strontium ferrite composite cathodes in solid oxide fuel cells

Degradation mechanisms of chromium poisoning have been extensively investigated for last two decades on various cathode materials for solid oxide fuel cells. While most researchers used half-cell experiments to investigate the effects of chromium impurities, this paper compares the degradation phenomena of LSM-YSZ and LSF-GDC cathodes in full cells under different operating conditions, namely polarized current density and humidity over the cathode. Under cathodic load, performance degradation of LSF-GDC cathode is significantly less than that of LSM-YSZ cathode. Most interestingly, under humidified air condition, LSF-based cell hardly experiences performance degradation while LSM-based cell shows a catastrophic degradation. Cr deposition in LSM-based cells occurs mainly near the electrolyte under both dry and humidified air conditions. In contrast, Cr deposition in LSF-based cell concentrates at the cathode surface under dry air condition, but concentrates both at cathode surface and near electrolyte under humidified air condition. Microstructure analysis reveals Mn-associated Cr deposits in LSM-based cathode, and Sr- and Fe-associated Cr deposits in LSF-based cathode. With the help of distribution of relaxation time analysis, the different electrochemical behaviors of LSM- and LSF-based cells are carefully interpreted. The effects of electrochemical deposition, Sr surface segregation, and humidity on LSM- and LSF-based cathodes are discussed.

25 ENERGY STORAGE↗

LONG-TERM PERFORMANCE OF SOLID OXIDE STACKS WITH ELECTRODE-SUPPORTED CELLS OPERATING IN THE STEAM ELECTROLYSIS MODE

Performance characterization and durability testing have been completed on two five-cell high-temperature electrolysis stacks constructed with advanced cell and stack technologies. The solid oxide cells incorporate a negative-electrode-supported multi-layer design with nickel-zirconia cermet negative electrodes, thin-film yttria-stabilized zirconia electrolytes, and multi-layer lanthanum ferrite-based positive electrodes. The per-cell active area is 100 cm2. The stack is internally manifolded with compliant mica-glass seals. Treated metallic interconnects with integral flow channels separate the cells. Stack compression is accomplished by means of a custom spring-loaded test fixture. Initial stack performance characterization was determined through a series of DC potential sweeps in both fuel cell and electrolysis modes of operation. Results of these sweeps indicated very good initial performance, with area-specific resistance values less than 0.5 ?.cm2. Long-term durability testing was performed with A test duration of 1000 hours. Overall performance degradation was less than 10% over the 1000-hour period. Final stack performance characterization was again determined by a series of DC potential sweeps at the same flow conditions as the initial sweeps in both electrolysis and fuel cell modes of operation. A final sweep in the fuel cell mode indicated a power density of 0.356 W/cm2, with average per-cell voltage of 0.71 V at a current of 50 A.

08 HYDROGEN↗

Investigation of Iron-Chromium-Niobium-Titanium Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect Applications

As part of an effort to develop cost-effective ferritic stainless steel-based interconnects for solid oxide fuel cell (SOFC) stacks, AL 441 HPTM was studied in terms of its metallurgical characteristics, oxidation behavior, and electrical performance. Minor alloying elements (Nb and Ti) captured interstitials such as C by forming carbides, stabilizing the ferritic structure and mitigating the risks of sensitization and inter-granular corrosion. Laves phases rich in Nb and Si precipitated along grain boundaries during high temperature exposure, improving the steel’s high temperature mechanical strength. The capture of Si in the Laves phase minimized the Si activity in the steel substrate and prevented formation of an insulating silica layer at the scale/metal interface. However, the relatively high oxidation rate, and thus increasing ASR over time, necessitates the application of a conductive protection layer on the steel. In particular, Mn1.5Co1.5O4 spinel protection layers drastically improved the electrical performance of the ferritic stainless steel 441, acting as barriers to chromium outward and oxygen inward diffusion.

Solid oxide fuel cell, interconnect, oxidation, co↗

Electrical Stability of a Novel Refractory Sealing Glass in a Dual Environment for Solid Oxide Fuel Cell Applications

A novel refractory alkaline-earth silicate (Sr-Ca-Y-B-Si) sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was sealed between two metallic interconnect plates and tested for electrical stability at elevated temperatures and duel environments under DC loading. The isothermal aging results showed very stable electrical resistivity with values 5-9 orders of magnititudes higher than typical SOFC function materials at 850 degrees C for ~700 hr. For comparison, the state-of-the-art sealing glass (G18, Ba-Ca-Al-B-Si) was also evaluated in a similar condition and showed less stable in accelerated tests at 830 degrees C for ~100 hr. Interfacial microstruicture was characterized and possible reactions were discussed.

30 DIRECT ENERGY CONVERSION↗

Electrochemical Performance and Stability of the Cathode for Solid Oxide Fuel Cells: III. Role of volatile boron species on LSM/YSZ and LSCF

Boron oxide is a key component to tailor the softening temperature and viscosity of the sealing glass for solid oxide fuel cells. The primary concern regarding the use of boron containing sealing glasses is the volatility of boron species, which possibly results in cathode degradation. In this paper, we report the role of volatile boron species on the electrochemical performance of LSM/YSZ and LSCF cathodes at various SOFC operation temperatures. The transport rate of boron, ~ 3.24×10-12 g/cm2•sec was measured at 750°C with air saturated with 2.8% moisture. A reduction in power density was observed in cells with LSM/YSZ cathodes after introduction of the boron source to the cathode air stream. Partial recovery of the power density was observed after the boron source was removed. Results from post-test secondary ion mass spectroscopy (SIMS) analysis the partial recovery in power density correlated with partil removal of the deposited boron by the clean air stream. The presence of boron was also observed in LSCF cathodes by SIMS analysis, however the effect of boron on the electrochemical performance of LSCF cathode was negligible. Coverage of triple phase boundaries in LSM/YSZ was postulated as the cause for the observed reduction in electrochemical performance.

30 DIRECT ENERGY CONVERSION↗

Infiltrated Sr 0.9 Y 0.1 CoO 2.5+δ nanoparticles as a cathode material for solid oxide fuel cells operated at 450–650 °C

Catalytically active cathode materials are highly desirable for the development of low-temperature solid oxide fuel cells (LT-SOFCs). In the present study, we report the performance of a high-loading Sr 0.9 Y 0.1 CoO 2.5+δ (SYC10) nanoparticles (NPs) as a catalytic cathode infiltrated in Ce 0.8 Gd 0.2 O 2-δ (GDC) backbones for LT-SOFCs and the use of a low-loading SYC10 NPs as a catalyst for promoting the performance of a commercial cathode. The loading and calcination temperature of SYC10 NPs were systematically optimized to achieve the lowest area-specific polarization resistance at ≤650 °C. A significant reduction in polarization resistance of commercial LSCF cathode by SYC NPs has also been demonstrated at 650 °C.

08 HYDROGEN↗

Fundamental study of gas species transport in the oxygen electrode of solid oxide fuel and electrolysis cells

A fundamental analysis of multicomponent gas transport models was performed in application to the oxygen electrodes of solid oxide cells. It is common practice to neglect the effect of pressure gradients within oxygen electrodes, even though a net molar flux at the electrolyte surface implies that a pressure gradient must exist. The influence of both Darcy velocity and Knudsen flux are considered in the context of ordinary (Fickian) diffusion, the dusty gas model, and the binary friction model. Comparisons between the models and different sets of assumptions are made via parametric studies on operating load, oxygen partial pressure, microstructural properties, and electrode thickness. Results show that the pressure gradient will have a significant impact on the oxygen concentration distribution and therefore the concentration overpotential. In electrolysis mode, pressure increases up to 1 atm are predicted, indicating that pressure at the electrode/electrolyte interface could contribute to electrode delamination. Additionally, it is found that Darcy's law is insufficient for calculating the pressure distribution without accounting for the flux due to Knudsen diffusion. Additionally, it is found that for the range of properties typical of oxygen electrodes, there is a negligibly small difference between the dusty gas model and binary friction model from a practical standpoint.

08 HYDROGEN↗

Life cycle analysis of a hydrogen production system based on solid oxide electrolysis cells integrated with different energy and wastewater sources

Hydrogen production via water electrolysis is a promising and evolving technology. The solid oxide electrolysis cell (SOEC) is one of the several technologies for this purpose. They are alternatives to the traditional hydrogen production from fossil fuels to enhance global energy decarbonization. However, in the bid for sustainability and a green economy, these technologies are not free from causing some environmental burdens. Using life cycle assessment (LCA), the greenhouse gas emission and degree of environmental impacts by these technologies can be identified and measured throughout their lifespan. This study addresses how to quantify these CO 2 emission impacts for an electrolytic system with different energy sources. The LCA of a novel integrated hydrogen production SOEC system with energy from solar photovoltaic and bituminous powerplant is performed using simaPro, the leading global LCA solution software. Measuring the environmental impact of the electrolytic operation in terms of weight, the bituminous powerplant poses damage which is, on average 700% more than solar PV. The thermal-to-hydrogen efficiency of the SOEC system is 56%, and a probable 28% reduction in carbon footprint with heat integration. The steam generation and the manufacturing of the SOEC have a very high environmental impact potential on the system. Here, we recommend LCA and net energy analysis is carried out for every new hydrogen technology and adequate comparison to enhance sustainable and green economy.

08 HYDROGEN↗

Hybrid Solid Oxide Fuel Cell/Gas Turbine Model Development for Electric Aviation

A thermodynamic model was developed and validated to analyze a high-performance solid oxide fuel cell and gas turbine (SOFC-GT) hybrid power system for electric aviation. This study used a process simulation software package (ProMax) to study the role of SOFC design and operation on the feasibility and performance of the hybrid system. Standard modules, including compressor, turbine, heat exchanger, reforming reactor, and combustor were used from the ProMax tool suite while a custom module was created to simulate the SOFC stack. The model used an SOFC test data set as an input. Additional SOFC stack performance effects, such as pressure, temperature, and utilization of air and fuel, were added from open source data. System performance predictors were SOFC specific power, fuel-to-electricity conversion efficiency, and hybrid system efficiency. Using these input data and predictors, a static thermodynamic performance model was created that can be modified for different system configurations and operating conditions. Prior to creating the final aircraft performance model, initial demonstration models were developed to validate output results. We used the NASA SOFC model as a benchmark, which was created with their Numerical Propulsion System Simulator (NPSS) software framework. Our output results matched within 1% of both the NASA model and open source SOFC performance data. With confidence gained in the accuracy of this model, a 1-MW SOFC-GT hybrid power system was constructed for an aircraft propulsion concept. Overall hybrid system efficiencies of > 75% FTE were observed during standard 36,000 feet cruise flight conditions.

30 DIRECT ENERGY CONVERSION↗

Lattice Boltzmann modelling of the coupling between charge transport and electrochemical reactions in a solid oxide fuel cell with a patterned anode

A fundamental understanding of the electrochemical reactions and the associated transport processes in electrodes of solid oxide fuel cells (SOFCs) is critical to the development of new electrode materials. To date, however, our understanding of the electrode processes is still very limited due to the lack of well-designed experiments and carefully-validated predictive models. To facilitate studies in this area, we have developed a numerical model that has taken into consideration of the coupling between the transport of mobile charged species (e.g., ions and electrons) in conducting phases and the electrochemical reactions at the three phase boundaries of an SOFC anode. The validity of this model has been confirmed by the electrochemical performance of test cells with a patterned anode consisting of well-defined electronic and ionic conducting phases. The model is then applied to quantifying the factors that critically influence the performance of a patterned anode, resulting in three key dimensionless parameters governing the coupling of transport and reactions in the anode: the ratio of electronic-to-ionic conductivity (σ el /σ ion ), the dimensionless exchange current density (i ex /i 0 ), and the dimensionless electric potential (Fφ 0 /RT). In particular, it is found that only i ex /i 0 and Fφ 0 /RT play a significant role under typical SOFC operating conditions: anode performance increases with the increase in i ex /i 0 and Fφ 0 /RT. Accordingly, we have constructed a phase map to demonstrate the combined effect of i ex /i 0 and Fφ 0 /RT, which is helpful for rational design and operation of SOFC patterned electrodes of different materials and geometries. More importantly, our present model is also applicable to the study of actual porous SOFC electrodes with known 3D microstructures.

08 HYDROGEN↗

Synthesis, characterization and mechanical properties of NiO - GDC20 (Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9}) nano composite anode for solid oxide fuel cells

In the present research work, X (NiO) +1-X(Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9}) where X = 30,40 and 45 wt% Nano Composite Anodes are synthesized for low temperature operating solid oxide fuel cells (SOFC). NiO and Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9} (GDC20) are synthesized by sol-gel citrate method and the nanopowders of NiO, GDC20 were calcined from 650 °c to 750 °c. For anode materials, pelletized the nanocomposites of X(NiO)+ (1-X) GDC20 (X = 30,40,45 wt.%) and sintered at 1200 °c. systematic study of atomic structure, purity, phase and structural parameters such as Lattice parameters, crystallite size of as-synthesized nanopowders and anode materials were carried out by XRD and SEM. For mechanical strength, Vickers micro-hardness of anode composites were estimated and observed that micro-hardness of composites were increasing with NiO wt.% and the density of sintered samples, which is varying from 4.35 to 5.54 Gpa at 500g load.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Exsolution and electrochemistry in perovskite solid oxide fuel cell anodes: Role of stoichiometry in Sr(Ti,Fe,Ni)O 3

The exsolution of metal cations from oxides under reducing fuel conditions ends in the formation of surface metallic nanoparticles, which can reduce Solid Oxide Fuel Cell anode polarization resistance. However, the loss of the B-site cations shifts the stoichiometry of the perovskite oxide. Depending on the amount exsolved and the initial stoichiometry, the exsolution can presumably shift the oxide away from its single-phase perovskite region. Herein, the direct comparison of initially stoichiometric composition Sr(Ti 0.3 Fe 0.63 Ni 0.07 )O 3-δ (STFN0) with initially A-site deficient Sr 0.95 (Ti 0.3 Fe 0.63 Ni 0.07 )O 3-δ (STFN5) is conducted and reported. X-ray diffraction along with scanning and transmission electron microscopy analysis of the oxides, which are both reduced at 850 °C in H 2 /H 2 O/Ar, demonstrates a similar size and density of exsolved Fe–Ni alloy nanoparticles, albeit with slightly different alloy compositions. Whereas the oxide phase in reduced STFN5 shows a well-ordered perovskite structure, the greater B-site deficiency in reduced STFN0 results in a highly disordered and strained structure. The electrochemical performance of STFN0 anodes is inferior to that of STFN5 anodes, and even worse than SrTi 0.3 Fe 0.7 O 3-δ (Ni-free) anodes. It appears that an initial Sr deficiency is important to avoid a too-high B-site deficiency after exsolution, which distorts the perovskite structure and impairs electrochemical processes.

25 ENERGY STORAGE↗

Layed Perovskite PRBA0.5SR0.5CO205 as High Performance Cathode for Solid Oxide Fuels Using Photon Conducting Electrolyte

The layered perovskite PrBa{sub 0.5}Sr{sub 0.5}Co{sub 2}O{sub 5+{delta}} (PBSC) was investigated as a cathode material for a solid oxide fuel cell using a proton-conducting electrolyte based on BaCe{sub 0.7}Y{sub 0.2}Zr{sub 0.1}O{sub 3-{delta}} (BCYZ). The sintering conditions for the PBSC-BCYZ composite cathode were optimized resulting in the lowest area-specific resistance and apparent activation energy obtained with the cathode sintered at 1200 C for 2h. The maximum power densities of the PBSC-BCYZ/BZCY/NiO-BCYZ cell were 0.179, 0.274, 0.395, and 0.522 Wcm{sup -2} at 550, 600, 650, and 700 C, respectively with a 15{micro}m thick electrolyte. A relatively low cell interfacial polarization resistance of 0.132 {Omega}cm{sup 2} at 700 C indicated that the PBSC-BCYZ could be a good cathode candidate for intermediate temperature SOFCs with proton-conducting electrolyte.

30 DIRECT ENERGY CONVERSION↗

Metal-supported solid oxide fuel cells operated in direct-flame configuration

Metal-supported solid oxide fuel cells (MS-SOFC) with infiltrated catalysts on both anode and cathode side are operated in direct-flame configuration, with a propane flame impinging on the anode. Placing thermal insulation on the cathode dramatically increases cell temperature and performance. The optimum burner-to-cell gap height is a strong function of flame conditions. Cell performance at the optimum gap is determined within the region of stable non-coking conditions, with equivalence ratio from 1 to 1.9 and flow velocity from 100 to 300 cm s -1 . In this region, performance is most strongly correlated to flow velocity and open circuit voltage. The highest peak power density achieved is 633 mW cm -2 at 833°C, for equivalence ratio of 1.8 and flow velocity of 300 cm s -1 . The cell starts to produce power within 10 s of being placed in the flame, and displays stable performance over 10 extremely rapid thermal cycles. The cell provides stable performance for >20 h of semi-continuous operation.

25 ENERGY STORAGE↗

Phase field simulation of anode microstructure evolution of solid oxide fuel cell through Ni(OH) 2 diffusion

Microstructure evolution in a solid oxide fuel cell anode is strongly affected by operating condition. The detailed mesoscale evolution mechanism under operating condition is still under debate. Here we develop a phase-field model to simulate microstructure evolution through formation and diffusion of gaseous Ni(OH)2. We studied the coarsening kinetics and redistribution of Ni under different steam distributions and compare it to that under pure hydrogen condition. Overall, the results suggest that although the presence of a steady gradient of steam leads to redistribution of Ni, Ni(OH) 2 formation and diffusion do not significantly change the Ni coarsening rate under strictly humid conditions, contrary to commonly reported hypotheses. It is concluded that competing mechanisms other than Ni(OH) 2 diffusion must be responsible for the experimentally observed Ni redistribution and enhanced coarsening under humid conditions.

25 ENERGY STORAGE↗

Current interrupt method for calculating the electrochemical impedance in a solid oxide electrolysis stack

Here, in this work the time domain response of Solid Oxide Electrolysis Cells (SOEC) to a current interruption was transformed into the frequency domain using a carrier function Laplace transform, which is fit to the experimental data using a MATLAB Complex Nonlinear Least Squares (CNLS) solver. The hardware implementation, consisting principally of a high-speed switch and a fast-logging Analog to Digital Converter (ADC), was assembled and tested using a calibration module to assess the accuracy, repeatability, and speed of acquisition of the prototype device as compared against a calibrated commercial impedance spectrometer. Additionally, the current interrupt device and commercial FRA were used to acquire the impedance spectra of a four cell SOEC stack with a large, 300 cm 2 , active cell area.

SOEC↗

Tin doped PrBaFe 2 O 5+δ anode material for solid oxide fuel cells

Ceramic anodes have many advantages over cermet anodes for solid oxide fuel cells. We report the synthesis and characterization of Sn doped double perovskite PrBaFe (2-x) Sn x O 5+δ (x = 0–0.3) anode materials. Different crystal structures were observed depending on the Sn doping level and gas atmosphere. The materials demonstrated excellent stability in both reducing and redox atmospheres at elevated temperatures. The oxygen content in the as-prepared PrBaFe (2-x) Sn x O 5+δ was nonlinearly correlated to the Sn doping level and reached maximum values around x = 0.1. After the reducing treatment, the oxygen content linearly decreased with increasing Sn doping level. The electrical conductivity of bulk PrBaFe (2-x) Sn x O 5+δ (x = 0.1) reached 63.6 S cm -1 at 800 °C in humidified hydrogen. At 750 °C, the surface exchange coefficient and bulk diffusivity of PrBaFe (2-x) Sn x O 5+δ reached the maximum values of 4.42 × 10 -6 m s -1 and 6.04 × 10 -7 m 2 s -1 , respectively, in the reducing process when the Sn doping level was x = 0.1. The activation energies of surface exchange coefficient and bulk diffusivity of PrBaFe (2-x) Sn x O 5+δ (x = 0.1) were 0.22 eV and 0.16 eV, respectively, in the reducing process. The area specific resistance of the PrBaFe (2-x) Sn x O 5+δ (x = 0.1) anode was 0.095–0.285 Ω cm 2 from 850–750 °C in humidified hydrogen, better than or comparable to the best ceramic anodes in the literature.

36 MATERIALS SCIENCE↗