Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Design of Experiments for Dynamic Test Runs in Solvent-Based CO 2 Capture Pilot Plants

Test runs in the pilot plants consume significant resources, and therefore, the learning from test runs should be maximized. Test runs conducted in the pilot plants are often steady state. It takes several hours for reaching steady-state in the pilot plants, and thus, the duration of the test runs needs to be long even for collecting few steady-state data points. On the other hand, a large number of measurements can be collected through dynamic test runs in a short span of time. This paper presents a systematic design of dynamic experiments (DoDEs) for identifiability of model parameters, which is achieved by persistently exciting the inputs signals. A pseudorandom binary sequence (PRBS) is designed as the input signal for DoDE due to its efficiency in obtaining sufficient spectral content. However, due to the long sequence size of the PRBS signal, a Schroeder-phase input signal, which is a multisine signal, is also designed. Tests for both types of signals are run in the Pilot Solvent Test Unit (PSTU) at the National Carbon Capture Center in Wilsonville, Alabama. The transient data are used to solve dynamic data reconciliation and parameter estimation problem. The estimated parameters are found to be not only superior to those estimated from using data collected from hundreds of steady-state test runs in a nonreactive (air–water) system, but the parameters could be estimated by using the dynamic data collected for about 24 h from the pilot plant for the MEA-H 2 O–CO 2 system.

CO2 capture↗
DOE OSTI2021

Spent Crystalline Silicotitanate Storage Study—Post AP-105DF Processing

A Tank-Side Cesium Removal (TSCR) system is under development by Washington River Protection Solutions to support initial production of immobilized low-activity waste (LAW) by feeding Hanford tank supernate from tank farms to the Hanford Waste Treatment and Immobilization Plant (WTP) LAW Facility. Tank waste supernate will be filtered to remove suspended solids and then Cs will be removed by processing it through crystalline silicotitanate (CST) ion exchange media manufactured by Honeywell UOP, LLC. The Cs-loaded CST columns will be stored indefinitely, with a goal of eventual CST removal and treatment. Thus, the spent CST needs to be recoverable after undetermined storage time. Previous testing with AP-105 simulant showed that rinsing the CST bed with 3 bed volumes (1.4 apparatus volumes [AVs]) of 0.1 M NaOH resulted in a dried bed that maintained flow characteristics indicative of ease of recovery. This study explored the intermediate conditions (between feed dried in place and the 1.4 AVs of 0.1 M NaOH rinse) to evaluate CST bed properties after: 1) stoppage with feed in place; 2) stoppage after draining feed; 3) stoppage after 0.7 AV of 0.1 M NaOH rinse through column; 4) stoppage after 1.5 AVs of 0.1 M NaOH rinse through column. Post processing, each column was heated at 50 °C for 19 days under pseudo-storage conditions to simulate the expected dried and stored CST bed conditions. Testing was conducted at the small scale (12-mL bed volume); actual, Cs-depleted, AP-105 tank waste was used as the feed. Post-dried CST bed physical properties (angle of repose and penetration depth) were measured to evaluate how CST moved and flowed. All process stop-conditions resulted in a solidified CST bed except for the final condition, 1.5 AVs of 0.1 M NaOH rinse. At this small scale, the three CST beds presented an issue for retrievability after the short storage period (19 days at 50 °C). The latter case confirmed the results from simulant testing. The testing was intended to provide a preliminary assessment of issues that may arise from desiccation of CST during storage with the indicated salt solutions in place. Since these were small-scale tests, the processing system did not scale to full scale conditions exactly; however, the tests did provide insight into the impact on the dried and stored CST bed after stopping processing at an earlier step (upset condition) than normal. These results indicate that if an upset condition occurs at TSCR, a dilute hydroxide rinse should be considered before the CST dries from internal heating.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

BENCH-SCALE DEVELOPMENT OF A TRANSFORMATIVE MEMBRANE PROCESS FOR PRE-COMBUSTION CO 2 CAPTURE

This final technical report describes work conducted by Membrane Technology and Research, Inc. (MTR) for the Department of Energy, National Energy Technology Laboratory (DOE NETL) on development of the second generation (Gen-2) Proteus™ membrane modules and a pre-combustion membrane process for carbon dioxide (CO 2 ) capture from an Integrated Gasification Combined Cycle (IGCC) plant for power generation (award number DE-FE0031632). The work was conducted from October 1, 2018 through March 30, 2022. The overall goal of this project was to bring a Gen-2 version of the H2-selective Proteus membrane to bench-scale module (component) testing with real syngas. MTR was assisted in this project by Susteon, a technology development company with extensive experience in gasification processes, and the University of North Dakota Energy & Environmental Research Center (EERC), who provided the host site for the slipstream field testing. This report details the work conducted to optimize the Gen-2 Proteus membrane and develop modules capable of operation at 200°C; demonstrate membrane module performance processing coal-derived syngas during a field test at EERC; and optimize integration of a dual-membrane process into an IGCC with carbon capture. Work for this project included membrane optimization and scale-up, module component screening and fabrication of high-temperature lab- and bench-scale modules, design and fabrication of a bench-scale field test membrane skid, operation of the field test skid processing coal-derived syngas at EERC, and a detailed techno-economic analysis (TEA) of the MTR dual-membrane process for IGCC power plant pre-combustion CO 2 capture. This project validated recent membrane technology advancements, mitigates risk in future scale-up activities, and moved the membrane pre-combustion capture technology from TRL-4 to TRL-5. Key results for each major task are discussed in the report.

10 SYNTHETIC FUELS↗
DOE OSTI2026

Characterization of NBCMA—A DAPO Precursor

As part of our investigation into the process optimization of 2,6-diaminopyrazine-1-oxide (DAPO), small-scale sensitivity testing (impact, friction, and ESD) was conducted on the precursor, N-nitroso-bis(cyanomethyl)amine (NBCMA). NBCMA exhibited moderate sensitivity to friction, whereas no sensitivity to impact or spark was observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High-speed X-ray imaging of droplet-powder interaction in binder jet additive manufacturing

Binder jetting (BJ) is an additive manufacturing process that uses a powder feedstock in a layer wise process to print parts by selectively depositing a liquid binder into the powder bed using inkjet technology. This study presents findings from high-speed synchrotron imaging of binder droplet-interaction during the BJ printing process. A custom laboratory-scale BJ test platform was used for testing which enabled control of relevant process parameters including powder material, print geometry, spacing between droplets, powder bed density, and powder moisture content. Powder ejection was observed above the powder bed surface and powder relocation due to droplet impact was observed below the powder bed surface. Powder relocation was observed to be sensitive to powder material, powder bed density, powder bed moisture, droplet spacing, and print geometry. Increasing powder bed density was found to increase particle ejection velocity but reduce the total number of particles ejected. Process parameters that increase binder / moisture content in the powder bed were found to reduce powder ejection. The number of ejected powder particles was reduced for lower droplet spacings. Both powder ejection and powder relocation below the powder bed were reduced by treating the surface of the powder bed with a water/triethylene glycol (TEG) mixture before printing. In conclusion, results from this study help to build understanding of the physical mechanisms in the BJ printing process that may contribute to formation of defects observed in final parts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Spectral properties of three-dimensional Anderson model

The three-dimensional Anderson model represents a paradigmatic model to understand the Anderson localization transition. In this work we first review some key results obtained for this model in the past 50 years, and then study its properties from the perspective of modern numerical approaches. Our main focus is on the quantitative comparison between the level sensitivity statistics and the level statistics. While the former studies the sensitivity of Hamiltonian eigenlevels upon inserting a magnetic flux, the latter studies the properties of unperturbed eigenlevels. We define two versions of dimensionless conductance, the first corresponding to the width of the level curvature distribution relative to the mean level spacing, and the second corresponding to the ratio of the Heisenberg time and the Thouless time obtained from the spectral form factor. We show that both conductances look remarkably similar around the localization transition, in particular, they predict a nearly identical critical point consistent with other well-established measures of the transition. We then study some further properties of those quantities: for level curvatures, we discuss particular similarities and differences between the width of the level curvature distribution and the characteristic energy studied by Edwards and Thouless (1972) in their pioneering work, in which the hopping at one lattice edge is changed from periodic to antiperiodic boundary conditions. In the context of the spectral form factor, we show that at the critical point it enters a broad time-independent regime, in which its value is consistent with the level compressibility obtained from the level variance. Finally, we test the scaling solution of the average level spacing ratio in the crossover regime using the cost function minimization approach introduced recently in Šuntajs et al. (2020). The latter approach seeks for the optimal scaling solution in the vicinity of the crossing point, while at the same time it allows for the crossing point to drift due to finite-size corrections. We find that the extracted transition point and the scaling coefficient agree with those from the literature to high numerical accuracy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗
DOE OSTI2023

Wettability variation and its impact on CO 2 storage capacity at the Wyoming CarbonSAFE storage hub: An experimental approach

Meeting global and national net zero carbon emission targets will require geologic carbon disposal. The U.S. Department of Energy (DOE) has accordingly funded significant research in this area, including the Wyoming CarbonSAFE project at Dry Fork Station (DFS) in Campbell County, Wyoming. This work studied wettability on micro- and macro-scales, CO 2 storage potential, and the correlation between the two to support the Wyoming CarbonSAFE project’s subsurface assessment. During the study, a target formation’s wettability was found to affect how much CO 2 can be stored in a given formation. Here, in this study, representative rock samples were selected from the target storage formations— Lakota, Hulett, and Minnelusa—based on the heterogeneity of the lithology, permeability, and porosity of the respective formations. The rock samples are all fine-grained sandstone with variable cementation and bedding structure, including different scales of laminated bedding. The porosity and permeability vary within the range of 9.0–14.3% and 0.1–28.9 mD, respectively. These rock samples were prepared for the micro-scale wettability (contact angle measurement), macro-scale wettability (wettability index derived from unsteady-state flow characterization for the core plugs), and CO 2 storage evaluation. The macro-scale experiments suggested that wettability appeared to dominate the CO 2 storage potential performance during the drainage process, where less water-wet behavior promoted higher CO 2 storage potential. The micro-scale wettability tests showed that the rock samples at the studied reservoir conditions behaved water-wet and became more water-wet as pressure increased. This kind of wettability change discourages further CO 2 storage potential yet benefits the CO 2 residual trapping as the CO 2 injection proceeds for the studied area. The results allow the recommendation of the best reservoir candidate for storage based on wettability that affects CO 2 storage. The work presented in this study provides valuable insights into wettability’s effect on the CO 2 storage capacity and wettability’s importance when identifying the optimal CO 2 storage formation to meet the project’s goals.

58 GEOSCIENCES↗
DOE OSTI2022

State-of-the-art and review of condensation heat transfer for small modular reactor passive safety: Experimental studies

Here this study focused on state-of-the-art and review of condensation heat transfer for small modular reactors (SMR). Nuclear reactors adopt passive containment cooling systems (PCCS) for accident mitigation, containment integrity, and primarily to maintain the last barrier for radioactive particle release to the environment during and beyond design-basis accidents. However, improving the effectiveness of the PCCS is more critical for the SMR than for commercial reactors to ensure higher safety margins and compactness. In the PCCS of SMR, due to its smaller size containment, the filmwise condensation (FWC) is dominant. Therefore, this study emphasized the FWC. Earlier condensation studies for the PCCS did not make SMR the primary focus, so a critical review for formulating the state-of-the-art was necessary. Part-1 of this study covered the review of physics phenomena, previous experimental studies with a brief overview of associated test facilities and empirical correlations. This study identified a research gap with the condensation test data scaling relations by using the information and findings of the previous PCCS studies and applied them to the SMR system.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Exact solution of burst pressure for thick-walled pipes using the flow theory of plasticity

This paper develops an exact solution of burst pressure for defect-free, thick-walled pipes using the flow theory of plasticity in terms of the average shear stress yield criterion (or Zhu-Leis yield criterion). The pipe steel is assumed to obey the power-law strain hardening rule, and large plastic deformation is described by the finite strain theory. On this basis, internal pressure is obtained as a power series function of the effective strains on the inside and outside surfaces of the thick-walled pipe with use of the second Bernoulli numbers. At burst failure, the Zhu-Leis flow solution of burst pressure is determined as a power series solution, and the burst effective strains, the burst effective stresses, and the burst pressure are functions of the diameter ratio (D o / D i ), strain hardening exponent (n), and ultimate tensile strength (UTS). Similarly, the Tresca and von Mises flow solutions of burst pressure are also determined as a power series solution in terms of the Tresca and von Mises yield criteria. A general closed-from exact solution of burst pressure is then proposed for the three yield criteria, and the results showed that the proposed exact solution matches well with the power series solution for each yield criterion. Moreover, the von Mises flow solution is an upper bound prediction, the Tresca flow solution is a lower bound prediction, and the Zhu-Leis flow solution is an intermediate prediction that agrees well with the finite element analysis results of burst pressure for thick-walled pipes. Furthermore, two datasets of full-scale burst tests are then utilized to evaluate and validate the proposed flow solutions of burst pressure for both thin and thick-walled pipes.

42 ENGINEERING↗
DOE OSTI2023

A parametric finite element study for determining burst strength of thin and thick-walled pressure vessels

To accurately predict the burst strength of both thin and thick-walled pressure vessels (PVs), a parametric study of PV burst strength was performed for a wide range of vessel geometries and materials using elastic-plastic finite element analysis (FEA). A valid FEA model was established through a detailed study of 2D versus 3D FEA models, the critical stress failure criterion versus the limit load criteria, and the thick-wall effect on the FEA simulations. Here, the results show that the stresses and strains at the mean diameter, rather than outside diameter, determines a more accurate burst strength for both thin and thick-walled PVs. On this basis, a parametrized FEA script using the ABAQUS Python application programming interface (API) was used to create a large database of PV burst strengths for a variety of vessel geometries and materials, demonstrating that Python scripting is a powerful technique for performing parametric studies or generating large databases. From the FEA results, using the regression method, a new burst pressure model was developed as a function of the vessel geometry (D/t ratio) and material properties (UTS and n). As validated by a large number of full-scale burst test data, the proposed burst model can very accurately predict the burst strength for both thin and thick-walled PVs.

42 ENGINEERING↗
DOE OSTI2023

Exact solutions of burst pressure for thick-walled cylinders in power-law strain hardening steels

Exact solutions of burst pressure for defect-free, thick-walled cylindrical pressure vessels with capped ends are developed using the flow theory of plasticity in terms of the Tresca, von Mises, and Zhu-Leis yield criteria. The material is assumed to obey a power-law strain hardening rule, and the finite strain theory is adopted to describe large plastic deformation. On this basis, internal pressure is obtained as a complex polynomial function of effective strains on the inside and outside surfaces of the pressure vessel with the use of the Bernoulli numbers. At burst failure, the effective strains and stresses on the inside and outside surfaces are first determined, and then three flow solutions of burst pressure are obtained as a power series function of the diameter ratio (D o /D i ), strain hardening exponent (n), and ultimate tensile strength (UTS). The power series solution is confirmed to agree well with the exact flow solution of burst pressure in a closed-form for each yield criterion, and the results show that the von Mises flow solution is an upper bound prediction, the Tresca flow solution is a lower bound prediction, and the Zhu-Leis flow solution is an intermediate prediction of burst pressure. In conclusion, two sets of full-scale burst test data are then utilized to evaluate and validate the proposed flow solutions of burst pressure for both thin-walled pipes and thick-walled cylindrical pressure vessels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A scalable DG solver for the electroneutral Nernst-Planck equations

The robust, scalable simulation of flowing electrochemical systems is increasingly important due to the synergy between intermittent renewable energy and electrochemical technologies such as energy storage and chemical manufacturing. The high Péclet regime of many such applications prevents the use of off-the-shelf discretization methods. In this work, we present a high-order Discontinuous Galerkin scheme for the electroneutral Nernst-Planck equations. The chosen charge conservation formulation allows for the specific treatment of the different physics: upwinding for advection and migration, and interior penalty for diffusion of ionic species as well the electric potential. Similarly, the formulation enables different treatments in the preconditioner: AMG for the potential blocks and ILU-based methods for the advection-dominated concentration blocks. Here we evaluate the convergence rate of the discretization scheme through numerical tests. Strong scaling results for two preconditioning approaches are shown for a large 3D flow-plate reactor example.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Multi-faceted framework for extrapolating early age flexural strength to facilitate rapid lifting/handling of high-volume fly ash precast members

Maintaining adequate early-age structural performance for precast concrete components has grown in importance as more sustainable mix designs become more widespread. Achieving high-early flexural strength is particularly crucial to facilitate rapid removal of hardened concrete components from formwork, often within 24 h after fresh concrete placement. Limited research has assessed the effectiveness of traditional design methods in correlating flexural strength with compressive strength for next-generation mix designs, or demonstrated extrapolation of such material performance to larger-scale structural tests. This paper presents a multi-faceted framework to reassess early-age flexural strength for concretes made with relatively high proportions of fly ash from both fresh and harvested sources. Here, the framework provides several pathways, from which the user can select based upon available resources and the specific application, to improve accuracy of early-age cracking moment calculations. Furthermore, the scope includes evaluation of strength performance under curing conditions emulative of those in a precast facility, recommending modulus of rupture equations which are more performance-driven than current design provisions, and experimental tests on prefabricated concrete beams to validate the proposed methodologies. Correlations of early-age strength with both concrete age and maturity measurements compare the effectiveness of utilizing in-situ data to further enhance the prediction methods. Ultimately, the proposed framework helped reduce errors when calculating cracking moment capacity at early ages by tailoring calculations to reflect mix-dependent behavior. Furthermore, most estimates of cracking moment were within 25 % of their corresponding experimental test results, thus promoting confidence for using these strategies with high-volume fly ash precast structures.

42 ENGINEERING↗
DOE OSTI2024

Effect of Inlet Throttling on Thermohydraulic Instability in a Large Scale Waterbased RCCS: A System-Level Analysis with RELAP5-3D

This paper presents results from system -level modeling of a water -based reactor cavity cooling system using RELAP5-3D. The computational model is benchmarked with experimental data from a half -scale RCCS test facility at Argonne National Laboratory. The model prediction is first compared with a two-phase oscillatory baseline experimental case where mixed accuracy is obtained. The model shows reasonable prediction of mass flow rate, pressure, and temperature but significant overprediction of void fraction. The model prediction is then compared with a fault case where the inlet of the risers is gradually reduced using a throttling valve. As the valve is closed, the model is able to predict some major flow phenomena observed in the experiment such as the dampening of oscillations, the reintroduction of oscillations, as well as boiling, flashing, and geysering in the risers. However, the timeline of these events are not well captured by the model. The model is also used to investigate the evolution of flow regime in the chimney. This work highlights that the semiempirical constitutive relations used in RELAP-3D could have a strong influence on the accuracy of the model in two-phase oscillatory flows.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

The effects of high energy deuteron ion beam irradiation on the tensile behavior of HT-9

Ion beam implantations are widely performed to understand the effects of irradiation-induced displacement damage on nuclear structural materials. However, the volume of material that can be investigated is often limited by the maximum energies of accelerator facilitates, leading to a limitation in the thickness of samples whose mechanical properties can be evaluated. The Lawrence Berkeley National Laboratory’s 88-Inch Cyclotron offers a wide range of ions and energies, allowing for material ion implantations at larger scales than typical. Four HT-9 SS-J-geometry tensile specimens were polished and then irradiated with deuterons at the 88-Inch Cyclotron to doses of approximately 0.2 dpa prior to small scale tensile testing. Here, the results from this study show irradiation hardening characterized by the tensile test results and black dot irradiation defects. Additionally, a comprehensive look at low temperature irradiations of high-Cr F/M steels is presented and our results show agreement with the available data.

36 MATERIALS SCIENCE↗