SEARCH · Engineering Papers
Results for “recyclable plastic”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Characterization of Volume F Trash from Four Recent STS Missions: Microbial Occurrence, Numbers, and Identifications
The fate of space-generated solid wastes, including trash, for future missions is under consideration by NASA. Several potential treatment options are under active technology development. Potential fates for space-generated solid wastes: Storage without treatment; storage after treatment(s) including volume reduction, water recovery, sterilization, and recovery plus recycling of waste materials. For this study, a microbial characterization was made on trash returned from four recent STS missions. The material analyzed were 'Volume F' trash and other bags of accompanying trash. This is the second of two submitted papers on these wastes. This first one covered trash content, weight and water content. Upon receipt, usually within 2 days of landing, trash contents were catalogued and placed into categories: drink containers, food waste, personal hygiene items, and packaging materials, i.e., plastic film and duct tape. Microbial counts were obtained with cultivatable counts on agar media and direct counts using Acridine Orange fluorescent stain (AODC). Trash bag surfaces, 25 square cm , were also sampled. Direct counts were approximately 1 x 10(exp 6) microbes/square cm and cultivatable counts ranged from 1 x 10 to 1 X 10(exp 4) microbes/ square cm-2. Aerobic microbes, aerobic sporeformers, and yeasts plus molds were common for all four missions. Waste items from each category were placed into sterile ziplock bags and 1.5 L sterile DI water added. These were then dispersed by hand shaking for 2 min. prior to inoculation of count media or determining AODC. In general, cultivatable microbes were found in drinks, food wastes, and personal hygiene items. Direct counts were usually higher than cultivatable counts. Some pathogens were found: Staphylococcus auerus, Escherichia coli (fecal wastes). Count ranges: drink pouches - AODC 2 x 10(exp 6) to 1 X 10(exp 8) g(sub fw) (exp -1); cultivatable counts variable between missions; food wastes: Direct counts were close to aerobic plate counts. Counts ranged from 10(exp 6) to 10(exp 9) per g(sub fw). Identities of isolates from cultivation media were obtained using a Biolog Microbial ID System or microSEQ molecular ID methodology using an ABI3130 gene analyzer.
Rapid Polyolefin Hydrogenolysis by a Single‐Site Organo‐Tantalum Catalyst on a Super‐Acidic Support: Structure and Mechanism
The novel electrophilic organo-tantalum catalyst AlS/TaNp x (1) (Np=neopentyl) is prepared by chemisorption of the alkylidene Np 3 Ta=CH t Bu onto highly Brønsted acidic sulfated alumina (AlS). Here, the proposed catalyst structure is supported by EXAFS, XANES, ICP, DRIFTS, elemental analysis, and SSNMR measurements and is in good agreement with DFT analysis. Catalyst 1 is highly effective for the hydrogenolysis of diverse linear and branched hydrocarbons, ranging from C2 to polyolefins. To the best of our knowledge, 1 exhibits one of the highest polyolefin hydrogenolysis activities (9,800 (CH 2 units) ⋅ mol(Ta) −1 ⋅ h −1 at 200 °C/17 atm H 2 ) reported to date in the peer-reviewed literature. Unlike the AlS/ZrNp 2 analog, the Ta catalyst is more thermally stable and offers multiple potential C−C bond activation pathways. For hydrogenolysis, AlS/TaNp x is effective for a wide variety of pre- and post-consumer polyolefin plastics and is not significantly deactivated by standard polyolefin additives at typical industrial concentrations.
NiTi Alloys: New Materials that enable Shockproof, Corrosion Immune Bearings
Though steel is the dominant material of choice for mechanical components (bearings and gears) it has intrinsic limitations related to corrosion and plastic deformation. In contrast, dimensionally stable nickel-rich Ni-Ti alloys, such as Nitinol 60, are intrinsically rustproof and can withstand high contact loads without damage (denting). Over the last decade, focused RD to exploit these alloys for new applications has revealed the science behind NiTi's remarkable properties. In this presentation, the state-of-the-art of nickel-rich NiTi alloys will be introduced along with a discussion of how NASA is adopting this new technology inside the space station water recycling system as a pathfinder for more down-to-earth tribological challenges.
Preprocessing of municipal solid waste towards thermal insulating material
Municipal solid waste (MSW) is one of the significant challenges in today’s world. A continuous surge in population, increasing living standards, and rapid urbanization are generating an enormous quantity of MSW. For example, the Environmental Protection Agency (EPA) reported that the total generation of MSW in the United States in 2018 was 292.4 million tons. Improper management of this MSW often leads to the release of greenhouse gases, emission of particulate matters, and formation of dioxins, which all ultimately contributes to climate change. Recycling these wastes via landfills with gas recovery and/or energy and material production via thermal and chemical conversions could be viable options to manage these challenges. Depending on the inherent chemical and structural properties of unrecycled wastes, the carbon structures can be tailored for processing and reuse in manufacturing of structural composites, building materials such as insulation, carbon dense reactant materials such as activated carbon, and so on. According to the EPA’s estimation, MSW in the United States is approximately 23% paper and paperboard, 12% plastics, 6% wood and 6% is textiles. Thus, this research focused on the feasibility of using the MSW as insulation material for the construction sector. The goal of this work was to determine the range of particle sizes, consolidation ratios, and component blends that can achieve insulation R-values within at least 70% that of traditional blown cellulose fiber. To achieve this goal, we designed the testing matrix based on five different component blends, three different particle sizes, and three different compaction level. An American Society for Testing and Materials (ASTM) method (C-739) was used to measure the R-value of the insulation material. Results showed that, adding more paper component in addition to smaller particle size and loose compaction made the insulation similar to the traditional blown cellulose fiber insulation as the R-value was within a range of 2.5-3.0 per inch.
Computational Nanomechanics of Carbon Nanotubes and Composites
Nanomechanics of individual carbon and boron-nitride nanotubes and their application as reinforcing fibers in polymer composites has been reviewed with interplay of theoretical modeling, computer simulations and experimental observations. The emphasis in this work is on elucidating the multi-length scales of the problems involved, and of different simulation techniques that are needed to address specific characteristics of individual nanotubes and nanotube polymer-matrix interfaces. Classical molecular dynamics simulations are shown to be sufficient to describe the generic behavior such as strength and stiffness modulus but are inadequate to describe elastic limit and nature of plastic buckling at large strength. Quantum molecular dynamics simulations are shown to bring out explicit atomic nature dependent behavior of these nanoscale materials objects that are not accessible either via continuum mechanics based descriptions or through classical molecular dynamics based simulations. As examples, we discus local plastic collapse of carbon nanotubes under axial compression and anisotropic plastic buckling of boron-nitride nanotubes. Dependence of the yield strain on the strain rate is addressed through temperature dependent simulations, a transition-state-theory based model of the strain as a function of strain rate and simulation temperature is presented, and in all cases extensive comparisons are made with experimental observations. Mechanical properties of nanotube-polymer composite materials are simulated with diverse nanotube-polymer interface structures (with van der Waals interaction). The atomistic mechanisms of the interface toughening for optimal load transfer through recycling, high-thermal expansion and diffusion coefficient composite formation above glass transition temperature, and enhancement of Young's modulus on addition of nanotubes to polymer are discussed and compared with experimental observations.
Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors
Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.
Characterization and engineering of a two-enzyme system for plastics depolymerization
Significance Deconstruction of recalcitrant polymers, such as cellulose or chitin, is accomplished in nature by synergistic enzyme cocktails that evolved over millions of years. In these systems, soluble dimeric or oligomeric intermediates are typically released via interfacial biocatalysis, and additional enzymes often process the soluble intermediates into monomers for microbial uptake. The recent discovery of a two-enzyme system for polyethylene terephthalate (PET) deconstruction, which employs one enzyme to convert the polymer into soluble intermediates and another enzyme to produce the constituent PET monomers (MHETase), suggests that nature may be evolving similar deconstruction strategies for synthetic plastics. This study on the characterization of the MHETase enzyme and synergy of the two-enzyme PET depolymerization system may inform enzyme cocktail-based strategies for plastics upcycling.
Hydroformylation of pyrolysis oils to aldehydes and alcohols from polyolefin waste
Waste plastics are an abundant feedstock for the production of renewable chemicals. Pyrolysis of waste plastics produces pyrolysis oils with high concentrations of olefins (>50 weight %). The traditional petrochemical industry uses several energy-intensive steps to produce olefins from fossil feedstocks such as naphtha, natural gas, and crude oil. In this work, we demonstrate that pyrolysis oil can be used to produce aldehydes through hydroformylation, taking advantage of the olefin functionality. These aldehydes can then be reduced to mono- and dialcohols, oxidized to mono- and dicarboxylic acids, or aminated to mono- and diamines by using homogeneous and heterogeneous catalysis. This route produces high-value oxygenated chemicals from low-value postconsumer recycled polyethylene. Here, we project that the chemicals produced by this route could lower greenhouse gas emissions ~60% compared with their production through petroleum feedstocks.
NiTi Alloys for Tribological Applications: The Role of In-Situ Nanotechnology
Beginning in 2004, NASA initiated the investigation and development of, Nitinol 60, a nickel-rich and dimensionally stable version of shape memory alloy Nitinol 55, as an alternative to bearing steel. Early investigations showed it to be hard and impervious to aqueous corrosion but the fundamental reasons for these properties were unknown. Shape memory alloys made from equiatomic Ni-Ti are widely known for their unique dimensional instability behavior that can be triggered by thermal and mechanical stress. The nickel-rich alloys exhibit no such dimension change property and have high hardness but have largely been overlooked by industry and the engineering community. Though steel is the dominant material of choice for mechanical components (bearings and gears) it has intrinsic limitations related to corrosion and plastic deformation. In contrast, Ni-Ti alloys are intrinsically rustproof and can withstand high contact loads without damage (denting). Over the last decade, focused RD to exploit these alloys for new applications has revealed that in-situ nano-scale phases that form during processing are largely responsible for NiTis remarkable properties. In this presentation, the state-of-art of nickel-rich NiTi alloys will be introduced and the nanotechnology behind their intriguing behavior will be addressed. The presentation will include discussion of how NASA is adopting this new technology inside the space station water recycling system as a pathfinder for more down-to-earth tribological challenges.
Upcycling Linear Low-Density Polyethylene Waste into Graphene for High Mass Loading Supercapacitors
Upcycling plastic into advanced carbons, such as graphene and porous carbon, offers attractive options to manage waste streams by converting the plastic into carbon electrode materials for energy storage devices. Linear low density polyethylene (LLDPE) is firstly bulk-oxidized with a facile and scalable method and then carbonized and catalyticlly graphenized into porous graphene materials. The LLDPE derived graphene (LLDPE-G) has a BET specific surface area up to 1800 m2/g and Raman ID/IG ratio of 0.85. When used as electrode material for symmetric supercapacitor, LLDPE-G possesses outstanding specific capacitance and excellent areal capacitance. Moreover, LLDPE-G exhibits exceptional cycling stability with capacitance retention of 95.8% after 100,000 cycles. Last but not least, KCl is recycled and reused over 3 cycles with material quality and electrocapacitive performance of LLDPE-G retained and verified after each cycle.
Mechanical and biochemical recovery of landfill waste in an underserved community
Historically in the United States, waste collected for recycling has been sold and shipped to processors in China. In 2013 and 2018, China introduced the Green Fence and National Sword policies which restricts the import of contaminated materials and banned the import of many recyclables. The cost of recycling in the United States has increased following these policy changes, which has led to many communities reducing their recycling programs or halting them altogether. Rural and underserved communities that don’t have resources to afford sophisticated recycling programs have been heavily impacted. Previous work at INL demonstrated that MSW is a potentially viable feedstock for both biochemical and thermochemical conversion. The goal of this project is to assess preprocessing tools that can produce consistent feedstocks that meet conversion specifications, remove problematic contaminants, and reduce the amount of waste that is landfilled. Municipal solid waste was collected from an underserved community in southeast Idaho, contaminants were characterized, and mechanically separated into two discrete fractions. The unit operations identified during mechanical separation trials will be mobilized to on-site with a goal of 50% recovery of paper and plastic waste.
Gold Catalyzed Polymerization Reactions of Unsaturated Substrates: Towards New Functional, Recyclable, and Upcycled Aromatic Polymers (Final Report)
The overarching goal of this project lied in the translation of gold (Au) catalyzed small molecule synthetic transformations to the field of polymer science, the generation of new macromolecular structures, and the application of the materials and methodologies produced toward sustainable polymer development and chemical upcycling. Specifically, this project aimed to polymerize monomers based on unsaturated precursors and access novel polymeric materials through the extension of Au catalyzed intermolecular processes. The specific objectives of this project comprised: (1) the extension of Au-catalyzed intermolecular reactions to bifunctional monomers and the polycondensation of diverse nucleophiles; (2) to gain fundamental mechanistic insight into Au-catalyzed polymerizations; (3) the application of these reactions to the synthesis of new classes of aromatic polymers that can be readily and/or selectively deconstructed; and (4) to apply these chemistries to post-polymerization modification (PPM) of commercially relevant polyaromatic substrates, including post-industrial plastics and post-consumer waste.
Integrated low-temperature PVC and polyolefin upgrading
Polyolefins and their chlorinated derivatives such as polyvinyl chloride (PVC) are among the most prevalent plastics in global production and waste streams. Traditional waste-to-energy methods such as incineration and pyrolysis, as well as most chemical upcycling methods for PVC utilization, require thorough, high-temperature dechlorination to prevent the release of toxic chlorinated compounds. Here, we present here a strategy for upgrading discarded PVC into chlorine-free fuel range hydrocarbons and hydrogen chloride in a single-stage process catalyzed by chloroaluminate ionic liquids. This approach offsets endothermic dechlorination and carbon-carbon bond cleavage with exothermic alkylation and hydrogen transfer by isobutane or isopentane in a low-temperature tandem process. The light isoalkanes are available from refinery processes and partly from recycling of the product stream. This process is suitable for handling real-world mixed and contaminated PVC and polyolefin waste streams.
Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing
Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.
Sustainable bioplastics derived from renewable natural resources for food packaging
Food packaging is one of the leading sectors for the end use of plastics. Bioplastic is produced from natural renewable resources such as crops, wood pulp, and herbaceous fibers. This article summarizes the rational design of bioplastics from natural resources for food packaging. The bioplastic properties considered include thermal properties, mechanical performance, oxygen/moisture resistance, and biodegradability. Bioplastic degradability and technologies for handling bioplastic waste are discussed. Various aspects of the sustainability of bioplastics (e.g., environmental profile, techno-economic analysis, and societal impact) are investigated. The main challenges of bioplastic application, such as low fracture strain and inferior barrier properties, are discussed. Mitigation approaches to overcome the mechanical properties of bioplastics, such as adding plasticizers, are also discussed. Bioplastic can have properties comparable with fossil-based plastics. In conclusion, bioplastic can be an alternative to conventional plastic in most applications of food packaging, which can reduce the carbon footprint and environmental impact because of its biodegradability.
Upcycling linear low-density polyethylene waste to turbostratic graphene for high mass loading supercapacitors
Linear low-density polyethylene (LLDPE) waste is difficult to upcycle into more valuable carbon materials because it tends to completely decompose into small molecules during thermal processing. In this work, LLDPE is upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K 2 CO 3 ) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400–950°C without decomposition of the polymer feedstock. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800m 2 g -1 and average Raman I D /I G and I 2D /I G ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses a specific capacitance up to 175Fg -1 at a mass loading of 20mgcm -2 , which is two times the commercial requirement, yielding an areal capacitance of 3.5 Fcm -2 . Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8 % after 100,000 cycles at a current density of 4.0 Ag -1 . Additionally, the KCl and K 2 CO 3 solids are recycled and reused over 3 complete reaction cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling waste LLDPE and other varieties of polyethylene into a higher value graphene used for electrochemical energy storage applications.
White Paper: Background Information on ARPA-E's Reuse Program
This document provides supplemental information for ARPA-E’s exploratory research program, “Recycle Underutilized Solids to Energy” (REUSE). The goal is to provide additional technical information to prospective Applicants. Further information is available in a blog interview and webinar at https://arpa-e.energy.gov/?q=news-item/trash-treasure-reuse-creates-feedstock-plastic-waste. Award information, submission requirements, evaluation criteria, and other applicable information is provided in Funding Opportunity Announcements DE-FOA-0001953 and DE-FOA-0001954 (SBIR/STTR). REUSE-specific requirements are provided in Topic K of those FOAs, and is available at https://arpa-e-foa.energy.gov/Default.aspx?Search=0001953&SearchType=#FoaIde8647d89-1cac-4b58-8622-1b04de8958c4. Under the REUSE Topic, ARPA-E seeks to fund the development of technologies to convert high-energy materials currently going to landfills to a high-energy content liquid product capable of displacing energy imports used for fuel or chemical production. The high-energy materials include plastics (#1-7 polymers, rubber, and composites) and paper. As discussed below, we estimate 30-34 MM ton plastic, 2-6 MM ton rubber, 18 MM ton of paper, and up to 0.1 MM ton composites are potentially available annually for this purpose. These numbers may be conservative based on changes in the plastic and paper export markets. ARPA-E anticipates deployment of multiple low-cost, simple, flexible, small-scale (100-500 ton per day) regional facilities using modular plants. This scale is consistent with the sources for high-energy materials, which include ~300 Material Recovery Facilities and industrial waste sources. The assumption is that such facilities can be more economical than the paradigm of large-scale facilities making purity products, due to cost for transporting and aggregating waste and the high operating costs (OPEX) and capital cost (CAPEX) for product purification. This document gives a brief technical review for multiple potential process technologies. The review is not intended to be comprehensive or limiting, only to provide an introduction to potential Applicants.