Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reactive power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

CEFR simulation using diffusion code system RAST-F

In this study, the RAST-F code system, which is based on the two-step approach that couples a multi-group cross-section generation Monte-Carlo (MC) code and a multi-group nodal diffusion solver, was used for the neutronic simulation of the CEFR start-up experiments. The numerical solution of the RAST-F system was verified against the full core MC solution MCS at all control rods fully inserted and withdrawn states. The RAST-F solution of the selected experimental simulations was compared against the measurement data. A good agreement between RAST-F and MCS solutions was observed with less than 120 pcm discrepancies and 1.2% root-mean-square error in terms of k{sub eff} and power distribution, respectively. Meanwhile, the RAST-F result agreed well with the experimental data within two-sigma of experimental uncertainty. The good agreement of these results indicates that RAST-F can be used to neutronic steady-state simulations for small core-size SFR, which was challenged to deterministic code systems. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

ECAR-6589 Reflector Support Structure Analysis: Project #33526

The MARVEL microreactor consists of five main systems: MRS (MARVEL Reactor Structure), PGS (Power Generation System), FCS (Fuel Core System), RCS (Reactivity Control System), and ICS (Instrument Control System). The RSS (Reflector Control System) is a sub system of the MRS which contains the upper and lower reflector support plates which support and locate the stationary core reflector and provide vertical support for the control drums. They are suspended from the Primary Coolant System by bolted structural straps which utilize a turnbuckle to allow for adjustment and leveling of the support plates. The stainless-steel support plates are each formed from four quarter circle segments which are bolted together around the lower core barrel. Bearing plates of non-galling Nitronic 60 alloy are fitted to the inner diameter of the support plates to prevent adhesive wear between the plates and the core barrel as the barrel expands and contracts due to changes in the temperature of the reactor.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

SPARTA: A flux adjustment methodology to interpret complex experiments

For the accurate determination of reactivity from a detector count rate, correction of spatial effects is of prime importance. This spatial correction is often provided using simulation methodologies, but this may introduce a bias if the result of the experiment is also used as input data for the simulation. Here, this work presents a flux adjustment methodology able to infer experimental reactivity and correction of spatial effects without the need for a simulation. It can process the signal from a complex experiment such as a heat balance measurement in the TREAT reactor, where control rods are continuously adjusted to maintain a constant power. In the present work, this methodology successfully computed the reactivity and the local spatial variation of the flux of a generated signal. It also proved to be robust against noise and errors on kinetic parameters and provides a credible interpretation of a heat balance experiment in TREAT. Efficiency of flux adjustment methods for complex experiment enable a better experiment interpretation less reliant on nuclear data evaluation.

73 - NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

A generalization of the shock invariant relationship

Shock invariant relationship, which was conceived for inert shock waves to derive the 4th power relationship between shock pressure and maximum strain rate, is generalized for reactive shock waves such as Chapman–Jouget detonation and shock-induced vaporization. The generalization, based on the first-order reaction models, is a power function relationship between overall dissipated energy (Δe dis ) and reaction time Δτ such that Δe dis Δτ 1/α = constant, where the power coefficient α is found to be in the range of 2/3–4. Experimental data, though scarce, are consistent with the generalization. Implication of the generalization for inert shocks is also considered and suggests a broad range of the 4th power coefficient including an inequality equation that constrains the shock and particle velocity relationship.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

A New Proposal Generalized Predictive Control Algorithm With Polynomial Reference Tracking Applied for Sodium Fast Reactors

This paper proposes a generalized predictive control (GPC) with constraints and orthonormal Laguerre functions using the simplified model of the primary system (reactor core and intermediate heat exchanger (IHX)) of a prototypical sodium fast reactor (SFR). This paper develops a multiple-input multiple-output (MIMO) GPC with input constraints able to track polynomial references of any degree applied in coolant temperature difference across the core and fractional power. The manipulated variables of the GPC-SFR are the reactivity and the sodium flow rate of the primary and secondary pipes. Moreover, orthonormal Laguerre functions and step down condition number techniques were also applied to avoid the numerical ill-conditioning issue in quadratic programming of large systems. Thus, a GPC type-2 was designed to control fractional power, coolant temperature difference across the core and sodium tank temperature of the SFR primary system when temperature references change according to a linear ramp after reaching their steady-state operation, sustaining 100% power operation on the reactor. In order to analyze the load tracking capability of the GPC-SFR type-2, the load following from 100% fractional power (FP) to 60% FP at 0.8% FP/min rate is simulated. Constraints on the rate of coolant temperature difference across the core and reactivity were applied for the design safety. For comparison criteria, this paper compares the GPC-SFR type-2 with the GPC-SFR type-1, i.e., standard model predictive control (MPC), to verify the viability and superior performance of the proposal regarding: (a) ramp-tracking capability of temperature and load; (b) the rejections of a reactivity disturbance of -1 cent and a secondary sodium inlet temperature disturbance of +10°F; and (c) a simulation with uncertainty in reactor design. The simulations show that the GPC-SFR type-2 overcome the GPC-SFR type-1 robustness and performance.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS2003

Low-Power RIE of SiO2 in CHF3 To Obtain Steep Sidewalls

A reactive-ion etching (RIE) process has been developed to enable the formation of holes with steep sidewalls in a layer of silicon dioxide that covers a silicon substrate. The holes in question are through the thickness of the SiO2 and are used to define silicon substrate areas to be etched or to be built upon through epitaxial deposition of silicon. The sidewalls of these holes are required to be vertical in order to ensure that the sidewalls of the holes to be etched in the substrate or the sidewalls of the epitaxial deposits, respectively, also turn out to be vertical.

Turner, Tasha↗
NASA NTRS2007

Testing in Support of Space Fission System Development and Qualification

Extensive data would be required for the qualification of a fission surface power (FSP) system. The strategy for qualifying a FSP system could have a significant programmatic impact. This paper explores potential options that could be used for qualifying FSP systems, including cost-effective means for obtaining required data. three methods for obtaining qualification data are analysis, non-nuclear testing, and nuclear testing. It has been over 40 years since the US qualified a space reactor for launch. During that time, advances have been made related to all three methods. Perhaps the greatest advancement has occurred in the area of computational tools for design and analysis. Tools that have been developed, coupled with modem computers, would have a significant impact on a FSP qualification. This would be especially true for systems with materials and fuels operating well within temperature, irradiation damage, and burnup limits. The ability to perform highly realistic non-nuclear testing has also advanced throughout the past four decades. Instrumented thermal simulators were developed during the 1970s and 1980s to assist in the development, operation, and assessment of terrestrial fission systems. Instrumented thermal simulators optimized for assisting in the development, operation, and assessment of modem FSP systems have been under development (and utilized) since 1998. These thermal simulators enable heat from fission to be closely mimicked (axial power profile, radial power profile, temperature, heat flux, etc.} and extensive data to be taken from the core region. Both steady-state and transient operation can be tested. For transient testing, reactivity feedback is calculated (or measured in cold/warm criticals) based on reactor temperature and/or dimensional changes. Pin power during a transient is then calculated based on the reactivity feedback that would occur given measured values of temperature and/or dimensional change. In this way nonnuclear testing can be used to provide very realistic information related to nuclear operation. Non-nuclear testing can be used at all levels, including component, subsystem, and integrated system testing. Realistic non-nuclear testing is most useful for systems operating within known temperature, irradiation damage, and burnup capabilities.

Houts, Mike↗
DOE OSTI2025

Chlorine gas and anion radical reactivity in molten salts and the link to chlorobasicity

Next-generation nuclear power plants may include exciting novel designs in which molten salts are the coolant or a combination of the coolant and fuel. Whereas it is straightforward to see why having a low volatility coolant can be advantageous for safety, much is not understood about the production of volatile halogen gases as a result of radiation and even less is known about the distribution of these species at and away from interfaces. Using first principles molecular dynamics simulations, we investigate the product of the disproportionation reaction between chlorine anion radicals (nominally Cl 2 ˙ − ) in the bulk and slab configurations. We find that the product depends on the chlorobasicity of the medium. For example, in ZnCl 2 , Cl 2 forms, but in a eutectic mixture of LiCl and KCl, Cl 3 − is formed as a product. We also find that Cl 3 − prefers to form at the vapor interface and this may have implications for corrosion and reactivity. Furthermore, the mechanisms of the mobility of Cl 2 and Cl 3 − are radically different, the first one being vehicular and the second Grotthus-like. Chlorobasicity is linked to the electronic structure of the host melt; ZnCl 2 forms extended networks along which metal ions and anionic counterions have significant electronic orbital overlap forming long, linear, molecular-like constructs; the opposite is true for the alkali metal eutectic salt.

Nguyen, Hung H. [Univ. of Iowa, Iowa City, IA (Uni↗
NASA NTRS1993

An architecture for object-oriented intelligent control of power systems in space

A control system for autonomous distribution and control of electrical power during space missions is being developed. This system should free the astronauts from localizing faults and reconfiguring loads if problems with the power distribution and generation components occur. The control system uses an object-oriented simulation model of the power system and first principle knowledge to detect, identify, and isolate faults. Each power system component is represented as a separate object with knowledge of its normal behavior. The reasoning process takes place at three different levels of abstraction: the Physical Component Model (PCM) level, the Electrical Equivalent Model (EEM) level, and the Functional System Model (FSM) level, with the PCM the lowest level of abstraction and the FSM the highest. At the EEM level the power system components are reasoned about as their electrical equivalents, e.g, a resistive load is thought of as a resistor. However, at the PCM level detailed knowledge about the component's specific characteristics is taken into account. The FSM level models the system at the subsystem level, a level appropriate for reconfiguration and scheduling. The control system operates in two modes, a reactive and a proactive mode, simultaneously. In the reactive mode the control system receives measurement data from the power system and compares these values with values determined through simulation to detect the existence of a fault. The nature of the fault is then identified through a model-based reasoning process using mainly the EEM. Compound component models are constructed at the EEM level and used in the fault identification process. In the proactive mode the reasoning takes place at the PCM level. Individual components determine their future health status using a physical model and measured historical data. In case changes in the health status seem imminent the component warns the control system about its impending failure. The fault isolation process uses the FSM level for its reasoning base.

Holmquist, Sven G.↗
NASA NTRSDate not supplied

Plasma Chemical Conversion and Resource Generation Beyond Low-Earth Orbit

As humanity gears up for its return to the moon after more than half a century, collaborative efforts between NASA, Artemis Accords Partners, and private industry are underway to establish the necessary infrastructure and technologies for lunar habitation and eventual Mars exploration. However, the traditional ISS resupply and waste management model is impractical and economically infeasible for prolonged missions to the Moon and Mars. Advanced chemical conversion technologies are needed to generate vital consumable products from local planetary resources (ISRU) and recycled gasses and waste within semi-closed loop life-support systems. Low-temperature plasma reactors are emerging power-to-gas technologies with the potential to facilitate various chemical synthesis processes with hardware commonality and redundancy. In plasma-based systems, electrical power is used to ionize a feedstock gas, creating a highly reactive environment that leverages electron excitation chemistry to break stable molecular bonds and form value added products. Unlike thermal chemical processes, plasma reactors operate at non-equilibrium conditions, allowing for lower-temperature operation and instantaneous start-up, making them adaptable to intermittent power availability. Moreover, their scalability permits deployment in both portable astronaut systems and large-scale industrial setups for colonies. One promising application of plasmas is for CO 2 conversion. Carbon dioxide comprises 96% of the Martian atmosphere and is a byproduct of human respiration, which typically must be scrubbed and vented from space habitats. A plasma source integrated with membrane separation technology could generate a stream of oxygen for life support and rocket propellant. CO 2 splitting may also be beneficial as a precursor to manufacture carbon-based products and fuels in situ, like methane, methanol, and polyethylene. Plasma-assisted CO 2 conversion is a simpler case to study without the concern of selectivity and is the first step toward complex chemical synthesis. This work presents preliminary experimental case study from a plasma reactor for CO 2 conversion and casts a vision for the potential of plasma technologies in a sub-architecture for resource production to enable the next generation of human spaceflight activities.

Plasma↗
DOE OSTI2023

Sensitivity study of parameters important to Molten Salt Reactor Safety

This paper presents a molten salt reactor (MSR) design parameter sensitivity study using a nodal dynamic modelling methodology with explicitly modified point kinetics equation and Mann’s model for heat transfer. Six parameters that can impact MSR safety are evaluated. A MATLAB-Simulink model inspired by Thorcon’s 550MW th MSR is used for parameter evaluations. A safety envelope was formed to encapsulate power, maximum and minimum temperature, and temperature-induced reactivity feedback. The parameters are perturbed by ±30%. The parameters were then ranked by their subsequent impact on the considered safety envelope, which ranks acceptable parameter uncertainty. The model is openly available on GitHub.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1991

Core reactivity estimation in space reactors using recurrent dynamic networks

A recurrent multilayer perceptron network topology is used in the identification of nonlinear dynamic systems from only the input/output measurements. The identification is performed in the discrete time domain, with the learning algorithm being a modified form of the back propagation (BP) rule. The recurrent dynamic network (RDN) developed is applied for the total core reactivity prediction of a spacecraft reactor from only neutronic power level measurements. Results indicate that the RDN can reproduce the nonlinear response of the reactor while keeping the number of nodes roughly equal to the relative order of the system. As accuracy requirements are increased, the number of required nodes also increases, however, the order of the RDN necessary to obtain such results is still in the same order of magnitude as the order of the mathematical model of the system. It is believed that use of the recurrent MLP structure with a variety of different learning algorithms may prove useful in utilizing artificial neural networks for recognition, classification, and prediction of dynamic systems.

Parlos, Alexander G.↗
NASA NTRS2005

Heat Pipe Reactor Dynamic Response Tests: SAFE-100 Reactor Core Prototype

The SAFE-I00a test article at the NASA Marshall Space Flight Center was used to simulate a variety of potential reactor transients; the SAFEl00a is a resistively heated, stainless-steel heat-pipe (HP)-reactor core segment, coupled to a gas-flow heat exchanger (HX). For these transients the core power was controlled by a point kinetics model with reactivity feedback based on core average temperature; the neutron generation time and the temperature feedback coefficient are provided as model inputs. This type of non-nuclear test is expected to provide reasonable approximation of reactor transient behavior because reactivity feedback is very simple in a compact fast reactor (simple, negative, and relatively monotonic temperature feedback, caused mostly by thermal expansion) and calculations show there are no significant reactivity effects associated with fluid in the HP (the worth of the entire inventory of Na in the core is .<el, so fluid movement and temperature changes will cause very minor effects). In previous SAFE-100 tests, the point kinetics model was based on core thermal expansion via deflection measurements. It was found that core deflection was a strung function of how the SAFE-100 modules were fabricated and assembled (in terms of straightness, gaps, and other tolerances). To remove the added variable of how this particular core expands as compared to a different concept, it was decided to use a temperature based feedback model (based on several thermocouples placed throughout the core).

Bragg-Sitton, Shannon M.↗
DOE OSTI2026

Assembly Bowing Reactivity Calculation Methodology Applied to Lead Fast Reactor

Ducted assemblies bow during operation due to power and temperature gradients which can be influenced by operating flow rates. For fast spectrum cores using ducted assemblies, the bowing behavior follows that of the duct and because there are gaps between the ducts, the bowing can result in compaction or expansion of the active core. This local displacement can have a positive or negative impact and knowing the net effect during transients is important for system reactivity control. Keeping the net bowing reactivity worth low is possible with attentive placement of load pads above the active core and selecting load pad gap thicknesses that result in a desired behavior at standard operating conditions. This paper considers a Lead Fast Reactor (LFR) concept fueled by HALEU UO2 developed by Westinghouse Electric Company (WEC) and applies a workflow of Argonne-developed codes to estimate the core bowing reactivity worth. Using orifice flow rates grouped by assembly type, the net reactivity impact due to core assembly bowing for the LFR was found to be small and in line with other liquid metal fast reactors: +29/+32/+35 pcm, or about +$0.049/+$0.055/+$0.059, for BOEC/MOEC/EOEC, respectively.

bowing reactivity↗
DOE OSTI2020

Computationally Directed Discovery of MoBi 2

Incorporating bismuth, the heaviest element stable to radioactive decay, into new materials enables the creation of emergent properties such as permanent magnetism, superconductivity, and nontrivial topology. Understanding the factors that drive Bi reactivity is critical for the realization of these properties. Using pressure as a tunable synthetic vector, we can access unexplored regions of phase space to foster reactivity between elements that do not react under ambient conditions. Furthermore, combining computational and experimental methods for materials discovery at high-pressures provides broader insight into the thermodynamic landscape than can be achieved through experiment alone, informing our understanding of the dominant chemical factors governing structure formation. Herein, we report our combined computational and experimental exploration of the Mo–Bi system, for which no binary intermetallic structures were previously known. Using the ab initio random structure searching (AIRSS) approach, we identified multiple synthetic targets between 0–50 GPa. Highpressure in situ powder X-ray diffraction experiments performed in diamond anvil cells confirmed that Mo–Bi mixtures exhibit rich chemistry upon the application of pressure, including experimental realization of the computationally predicted CuAl 2 -type MoBi 2 structure at 35.8(5) GPa. Electronic structure and phonon dispersion calculations on MoBi 2 revealed a correlation between valence electron count and bonding in high-pressure transition metal–Bi structures as well as identified two dynamically stable ambient pressure polymorphs. Our study demonstrates the power of the combined computational–experimental approach in capturing highpressure reactivity for efficient materials discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

DFT Accurate Interatomic Potential for Molten NaCl from Machine Learning

Molten alkali chloride salts are a critical component in concentrated solar power and nuclear applications. Despite their ubiquity, the extreme chemical reactivity of molten alkali chlorides at high temperatures has presented a significant challenge in characterizing atomic structures and dynamic properties experimentally. In this work, we we investigate molten NaCl by performing high temperature molecular dynamics simulations using a Gaussian Approximation Potential (GAP) trained on Density Functional Theory (DFT) datasets. Our GAP model, trained with a meager 1000 atomic configurations, arrives at near ab initio accuracy with a mean absolute error of 1.5 meV/atom thus enabling fast analysis of high temperature salt properties on large length (5000 ion pairs) and time (> 1ns) scales currently inaccessible to ab initio simulations. Calculated structure factors and diffusion constants from our GAP model simulations show excellent agreement with experiments. Our results indicate that GAP models are able to capture the many-body interactions required to accurately model ionic-systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Benchmark Calculation for Turkey Point Unit 3 Cycles 1-3 Using the SCALE 6.3/Polaris–PARCS v3.4.2 Code Package

Benchmark calculations were performed for Turkey Point Unit 3 cycles 1–3 to validate the SCALE 6.3/Polaris–PARCS v3.4.2 code with the ENDF/B–VII.1 56–group library by comparing the simulated results with the measured data. The benchmark results will be used in evaluating the SCALE/Polaris–PARCS code package’s uncertainties for pressurized water reactor physics analysis. That future analysis will include key nuclear parameters such as reactivity, control bank worth, temperature coefficients, and pin and assembly power peaking factors. The present document details plant and fuel design specifications and input data for SCALE/Polaris, GenPMAXS, and PARCS. Additional details are provided with respect to the input and output files produced for the benchmark calculations. The benchmark results are summarized such that they can be used in evaluating uncertainties with other benchmark results for key nuclear parameters.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Benchmark Calculation for Surry Unit 1 Cycles 1-3 Using the SCALE 6.3/Polaris–PARCS v3.4.2 Code Package

The benchmark calculations were performed for Surry Unit 1 cycles 1–3 to validate the SCALE 6.3/Polaris–Purdue Advanced Reactor Core Simulator (PARCS) v3.4.2 with the ENDF/B–VII.1 56–group library by comparing the simulated results with the measured data. The benchmark results will be used to evaluate uncertainties of the SCALE/Polaris–PARCS code package for pressurized water reactor physics analysis for key nuclear parameters such as reactivity, control bank worth, temperature coefficients, and pin and assembly power peaking factors. This report details plant and fuel design specifications and input data for SCALE/Polaris, GenPMAXS, and PARCS. Additional details are provided for the input and output files produced for the benchmark calculations. The benchmark results were summarized such that they can be used in evaluating uncertainties with other benchmark results for key nuclear parameters.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗