Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ramping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Shock response of cobalt-based cemented tungsten carbides at pressures up to 100 GPa

In the present study, shock wave experiments are conducted on General Carbide cemented tungsten carbides with 3.7 wt.% and 6.0 wt.% cobalt binder to determine their shock compression response up to 100 GPa. A three-stage particle velocity profile is observed in the experiments -- an initial elastic-rise to the Hugoniot elastic limit (HEL), an elastic-plastic ramp indicating post-yield hardening, and finally a rise to the peak shocked Hugoniot state. The results of the experiments are used to determine the HEL, shock velocity (U s ) vs. particle velocity (u p ) Hugoniot relationship, and the longitudinal stress vs. specific volume Hugoniot relationship for the two samples. Here, the HEL for the WC 3.7wt% Co and WC 6.0wt% Co samples was determined to be ~4.45 GPa and 3.72 GPa, respectively. The U s – u p relation was determined to be U s = 4.97(0.006)+1. 446 (0.018) u p for WC 3.7 wt.% Co and U s = 4.93(0.006)+1. 454(0.017)u p for the WC 6.0 wt.% Co sample at peak particle velocities>0.75 km/s. For both WC grades, in the particle velocity regime less than ~0.75 km/s, the measured shock wave velocities were found to be larger than those predicted by the linear U s –u p Hugoniot relationship, indicating the two WC samples to preserve substantial strength in the post-yield deformation regime. Both WC grades show a catastrophic drop in shear stress carrying capacity when shocked to longitudinal stresses greater than ~70 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Power matching to pulsed inductively coupled plasmas

Matching of power delivery to nonlinear loads in plasma processing is a continuing challenge. Plasma reactors used in microelectronics fabrication are increasingly multi-frequency and/or pulsed, producing a non-linear and, in many cases, non-steady state electrical termination that can complicate efficient power coupling to the plasma. This is particularly the case for pulsed inductively coupled plasmas where the impedance of the plasma can significantly change during the start-up-transient and undergo an E–H (capacitive-to-inductive) transition. In this paper, we discuss the results from a computational investigation of the dynamics of power matching to pulsed inductively coupled plasmas (Ar/Cl 2 mixtures of tens of mTorr pressure) using fixed component impedance matching networks and their consequences on plasma properties. In this investigation, we used set-point matching where the components of the matching network provide a best-case impedance match (relative to the characteristic impedance of the power supply) at a chosen time during the pulsed cycle. Matching impedance early during the pulse enables power to feed the E-mode, thereby emphasizing capacitive coupling and large excursions in the plasma potential. This early power coupling enables a more rapid ramp-up in plasma density while being mismatched during the H-mode later in the pulse. The early match also produces more energetic ion bombardment of surfaces. Matching late in the pulse diminishes power dissipated in the E-mode at the cost of also reducing the rate of increase in plasma density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Experimental evaluation of shear modulus scaling of dynamic strength at extreme pressures

Recent progress in the development of dynamic strength experimental platforms is allowing for unprecedented insight into the assumptions used to construct constitutive models operating in extreme conditions. In this work, we make a quantitative assessment of how tantalum strength scales with its shear modulus to pressures of hundreds of gigapascals through a cross-platform examination of three dynamic strength experiments. Specifically, we make use of Split–Hopkinson pressure bar and Richtmyer–Meshkov instability experiments to assess the low-pressure strain and strain rate dependence. Concurrent examination of magnetically driven ramp-release experiments up to pressures of 350GPa allows us to examine the pressure dependence. In this work, using a modern description of the shear modulus, validated against both ab initio theory and experimental measurements, we then assess how the experimentally measured pressure dependence scales with shear modulus. Furthermore, we find that the common assumption of scaling strength linearly with the shear modulus is too soft at high pressures and offer discussion as to how descriptions of slip mediated plasticity could result in an alternative scaling that is consistent with the data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Trajectory of a flying plasma mirror traversing a target with density gradient

It has been proposed that laser-induced relativistic plasma mirror can accelerate if the plasma has a properly tailored density profile. Such accelerating plasma mirrors can serve as analog black holes to investigate Hawking evaporation and the associated information loss paradox. Here we reexamine the underlying dynamics of mirror motion in a graded-density plasma to provide an explicit trajectory as a function of the plasma density and its gradient. Specifically, a decreasing plasma density profile (down-ramp) along the direction of laser propagation would in general accelerate the mirror. In particular, a constant-plus-exponential density profile would generate the Davies–Fulling trajectory with a well-defined analog Hawking temperature, which is sensitive to the plasma density gradient but not to the density itself. Furthermore, we show that without invoking nano-fabricated thin-films, a much lower density gas target at, for example, ~1 × 10 17 cm -3 , would be able to induce an analog Hawking temperature, k B T H ~3.1 × 10 -2 eV, in the far-infrared region. We hope that this would help to better realize the experiment proposed by Chen and Mourou.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Vanadium oxide coatings to self-regulate current sharing in high-temperature superconducting cables and magnets

High-temperature superconductors such as REBa 2 Cu 3 O 7-δ (REBCO, RE = rare earth) enable high-current cables and high-field magnets. By removing the turn-to-turn insulation in a magnet application, recent experiments demonstrated that REBCO magnets can self-protect against catastrophic damage during a superconducting-to-normal transition (quench), i.e., when the stored magnetic energy rapidly converts to heat. The current can bypass the hot spot during a quench, thereby reducing the localized heat dissipation. The removal of the insulation between turns, however, leads to excessive eddy currents during current ramping, thereby forcing a much-prolonged magnet charging time. To address this issue, we investigate vanadium oxide (VO x ) coatings as a temperature-dependent self-switching medium that automatically manages current sharing. VO x coatings (with 1.70 ≤ × ≤ to 2.07) were deposited by reactive cathodic arc deposition, initially on insulating glass to determine the electrical properties, and later on commercial REBCO tapes. The coatings are x-ray amorphous but with a short-range crystalline ordering according to Raman spectrometry. The resistivity of VO x decreased by at least three orders of magnitude when the temperature increased from 80 to 300 K. The coating process is compatible with commercial REBCO tapes as evidenced by the negligible change in the critical current caused by the coating process. Here, the results from current sharing experiments and circuit analysis suggest that the VO x coating can effectively self-regulate current sharing in REBCO magnets, suppress excessive eddy currents, and enable self-protection during quenches.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Adaptive 3D convolutional neural network-based reconstruction method for 3D coherent diffraction imaging

We present a novel adaptive machine-learning based approach for reconstructing three-dimensional (3D) crystals from coherent diffraction imaging. We represent the crystals using spherical harmonics (SH) and generate the corresponding synthetic diffraction patterns. We utilize 3D convolutional neural networks (CNNs) to learn a mapping between 3D diffraction volumes and the SH, which describe the boundary of the physical volumes from which they were generated. We use the 3D CNN-predicted SH coefficients as the initial guesses, which are then fine-tuned using adaptive model-independent feedback for improved accuracy. We also adaptively tune the locations, intensities, and decay rates of collections of radial basis functions in order to reproduce the non-uniform internal structure of 3D objects and demonstrate the method for a synthetic volume that has an internal void and a density ramp.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental observations of exploding bridgewire detonator function

Exploding bridgewire detonators are an industry standard technology used for over 75 years and valued for their precise timing and safety characteristics. Despite widespread use, their functional mechanism remains controversial with both shock and non-shock mechanisms attributed. In this work, we re-examine bridgewire detonator function with a suite of modern diagnostics and compare these observations with the existing literature. Traditional detonator observations consisted of voltage applied to the bridgewire and time dependent current, integral response measurements such as case motion and more recently Schlieren imaging of the detonator surface. In this work, we add visible light emission, X-ray transmission, proton radiography, and temperature measurements during detonator function in addition to voltage, current, and function times. The addition of in-situ observations of light emission, temperature, and density gives us new insight into the mechanisms of explosive bridgewire detonator function. We see a distinct separation in time, location, symmetry, and velocity of bridgewire output and detonation onset. During the time between bridgewire burst and the initiation of detonation, we observe a temperature ramp in the input pellet. In this paper, we present the suite of measurements and comparisons with the literature on integral response measurements.

42 ENGINEERING↗
DOE OSTI2021

Instrument for spatially resolved, temperature-dependent electrochemical impedance spectroscopy of thin films under locally controlled atmosphere

We demonstrate an instrument for spatially resolved measurements (mapping) of electrochemical impedance under various temperatures and gas environments. Automated measurements are controlled by a custom LabVIEW program, which manages probe motion, sample motion, temperature ramps, and potentiostat functions. Sample and probe positioning is provided by stepper motors. Dry or hydrated atmospheres (air or nitrogen) are available. The configurable heater reaches temperatures up to 500 °C, although the temperature at the sample surface is moderated by the gas flow rate. The local gas environment is controlled by directing flow toward the sample via a glass enclosure that surrounds the gold wire probe. Software and hardware selection and design are discussed. Reproducibility and accuracy are quantified on a Ba(Zr,Y)O 3-δ proton-conducting electrolyte thin film synthesized by pulsed laser deposition. The mapping feature of the instrument is demonstrated on a compositionally graded array of electrocatalytically active Ba(Co,Fe,Zr,Y)O 3-δ thin film microelectrodes. The resulting data indicate that this method proficiently maps property trends in these materials, thus demonstrating the reliability and usefulness of this method for investigating electrochemically active thin films.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Modeling q 95 windows for the suppression of edge localized modes by resonant magnetic perturbations in the DIII-D tokamak

A toroidal asymptotic matching model of the response of a tokamak plasma to a static resonant magnetic perturbation (RMP) is used to simulate the n = 3 RMP-induced edge-localized-mode-suppression windows in q 95 that are evident when the plasma current is slowly ramped in DIII-D discharge #145380. All quantities employed in the simulation are derived from experimental measurements, apart from the neutral particle data. Three cases are considered. In the first case, the natural frequencies of tearing modes resonant in the plasma are determined by the ion flows at the corresponding resonant surfaces, which is the prediction of nonlinear tearing mode theory. In the second case, the natural frequencies are determined by the local E x B velocities at the resonant surfaces. In the third case, the natural frequencies are determined by the electron flows at the resonant surfaces, which is the prediction of linear tearing mode theory. The second case gives the best agreement between the simulations and the experimental observations. The first and third cases only lead to partial agreement between the simulations and the observations. In the first case, the lack of complete agreement may be a consequence of using an inaccurate assumption for the neutral particle distribution in the pedestal. In the third case, the lack of complete agreement is probably due to the fact that the response of a tokamak plasma to an RMP is not accurately described by linear tearing mode theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Pedestal magnetic turbulence measurements in ELMy H-mode DIII-D plasmas by Faraday-effect polarimetry

Internal magnetic fluctuation measurements are utilized to identify turbulence associated with micro-tearing modes (MTM) in the DIII-D Edge-Localized-Mode (ELM)-y H-mode pedestal. Using a Faraday-effect polarimeter, magnetic turbulence (150–500 kHz) is directly observed with a typical line-averaged fluctuation amplitude of ~0.8 G at peak frequency (250 kHz) and ~15 G integrated over the spectrum from 150 to 500 kHz. Frequency, poloidal wavenumber, and propagation direction of the magnetic turbulence all serve to identify as MTM. Magnetic turbulence amplitude non-monotonically correlates with collision frequency, peaks off mid-plane, and correlates with electron temperature gradient evolution between ELMs, consistent with MTM features identified from theory and gyro-kinetic simulation. The magnetic turbulence growth correlates with confinement degradation in ELMy H-mode plasmas during a slow density ramp. In conclusion, these internal measurements provide unique constraints toward developing physics understanding and validating models of the H-mode pedestal for future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Measurement of the strengths of Be and Pb4Sb by quasi-isentropic compress and release at near 100 GPa

The Ramp-compression experiments have been performed on the “Z” pulsed-power facility to investigate the strengths of Be and lead-antimony alloy. Yield strength and shear stress near peak pressure were obtained from measurements of the sound speed on release and using the Asay self-consistent method. Two S-65 grade Be samples, from batches which showed a significant difference in yield strength at ambient conditions, were found to have near identical yield strengths, which were also in agreement with similar earlier measurements on S-200 grade Be. Yield strength of Pb4Sb alloy at ~120 GPa was 1.35 GPa, while a National Ignition Facility (NIF) experiment by A. Krygier et al. (Phys. Rev. Lett. 123, 205701 (2020)) found 3.8 GPa at ~400 GPa pressure. Our result is intermediate between the ambient value and the Krygier one, but the significantly increased strength is probably not associated with the transition to the high-pressure bcc phase of lead.

42 ENGINEERING↗
DOE OSTI2021

Techniques for studying materials under extreme states of high energy density compression

The properties of materials under extreme conditions of pressure and density are of key interest to a number of fields, including planetary geophysics, materials science, and inertial confinement fusion. In geophysics, the equations of state of planetary materials, such as hydrogen and iron, under ultrahigh pressure and density provide a better understanding of their formation and interior structure [Celliers et al., “Insulator-metal transition in dense fluid deuterium,” Science 361, 677–682 (2018) and Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)]. The processes of interest in these fields occur under conditions of high pressure (100 GPa–100 TPa), high temperature (>3000 K), and sometimes at high strain rates (>103 s−1) depending on the process. With the advent of high energy density (HED) facilities, such as the National Ignition Facility (NIF), Linear Coherent Light Source, Omega Laser Facility, and Z, these conditions are reachable and numerous experimental platforms have been developed. To measure compression under ultrahigh pressure, stepped targets are ramp-compressed and the sound velocity, measured by the velocity interferometer system for any reflector diagnostic technique, from which the stress-density of relevant materials is deduced at pulsed power [M. D. Knudson and M. P. Desjarlais, “High-precision shock wave measurements of deuterium: Evaluation of exchange-correlation functionals at the molecular-to-atomic transition,” Phys. Rev. Lett. 118, 035501 (2017)] and laser [Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)] facilities. To measure strength under high pressure and strain rates, experimenters measure the growth of Rayleigh–Taylor instabilities using face-on radiography [Park et al., “Grain-size-independent plastic flow at ultrahigh pressures and strain rates,” Phys. Rev. Lett. 114, 065502 (2015)]. The crystal structure of materials under high compression is measured by dynamic x-ray diffraction [Rygg et al., “X-ray diffraction at the national ignition facility,” Rev. Sci. Instrum. 91, 043902 (2020) and McBride et al., “Phase transition lowering in dynamically compressed silicon,” Nat. Phys. 15, 89–94 (2019)]. Medium range material temperatures (a few thousand degrees) can be measured by extended x-ray absorption fine structure techniques, Yaakobi et al., “Extended x-ray absorption fine structure measurements of laser-shocked V and Ti and crystal phase transformation in Ti,” Phys. Rev. Lett. 92, 095504 (2004) and Ping et al., “Solid iron compressed up to 560 GPa,” Phys. Rev. Lett. 111, 065501 (2013), whereas more extreme temperatures are measured using x-ray Thomson scattering or pyrometry. This manuscript will review the scientific motivations, experimental techniques, and the regimes that can be probed for the study of materials under extreme HED conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simultaneous inference of the compressibility and inelastic response of tantalum under extreme loading

We study the deformation of tantalum under extreme loading conditions. Experimental velocity data are drawn from both ramp loading experiments on Sandia’s Z-machine and gas gun compression experiments. The drive conditions enable the study of materials under pressures greater than 100 GPa. We provide a detailed forward model of the experiments including a model of the magnetic drive for the Z-machine. Utilizing these experiments, we simultaneously infer several different types of physically motivated parameters describing equation of state, plasticity, and anelasticity via the computational device of Bayesian model calibration. Characteristics of the resulting calculated posterior distributions illustrate relationships among the parameters of interest via the degree of cross correlation. The calibrated velocity traces display good agreement with the experiments up to experimental uncertainty as well as improvement over previous calibrations. Examining the Z-shots and gun-shots together and separately reveals a trade-off between accuracy and transferability across different experimental conditions. Implications for model calibration, limitations from model form, and suggestions for improvements are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

In situ detection of RF breakdown on microfabricated surface ion traps

We report microfabricated surface ion traps are a principal component of many ion-based quantum information science platforms. The operational parameters of these devices are pushed to the edge of their physical capabilities as the experiments strive for increasing performance. When the applied radio-frequency (RF) voltage is increased excessively, the devices can experience damaging electric discharge events known as RF breakdown. We introduce two novel techniques for in situ detection of RF breakdown, which we implemented while characterizing the breakdown threshold of surface ion traps produced at Sandia National Laboratories. In these traps, breakdown did not always occur immediately after increasing the RF voltage, but often minutes or even hours later. This result is surprising in the context of the suggested mechanisms for RF breakdown in vacuum. Additionally, the extent of visible damage caused by breakdown events increased with the applied voltage. To minimize the probability for damage when RF power is first applied to a device, our results strongly suggest that the voltage should be ramped up over the course of several hours and monitored for breakdown.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Modeling atomically mixed graded density impactors

Graded density impactors (GDIs) are multi-material composite impactors used in gas gun experiments to tailor the drive conditions imparted to a sample test material. Previous graded density impactors generally rely on thin, but discrete, layers of different materials. The thinner and the greater number of layers will result in smoother compression. Taken to the limit of very thin layers would be pure material 1 at one surface, such as the front surface of an impactor, smoothly transitioning at the atomic scale to pure material 2 on the back surface. Such an impactor can initially shock, then smoothly compresses a material during a dynamic experiment. This type of experiment can serve to explore a larger region of thermodynamic space than a single or even multi-shock experiments. An overview of how graded density impactors are made is reviewed and sample results are given. Additionally, a strategy for modeling these kinds of impactors is presented. The length scales of constituent mixing are given from the experimental build through electrochemical-deposition. Equation of state models for pure constituents and their subsequent mixtures are presented. It is demonstrated that the time scales for pressure and temperature equilibration, for atomically mixed GDIs, are short enough to be a justifiable closure for the resulting multiphase flow. Furthermore, we present simulation results of dynamic shock followed by a ramp compression, utilizing a silver/gold graded density impactor, onto a tantalum sample.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Exploring implosion designs for increased compression on the National Ignition Facility using high density carbon ablators

It has long been recognized that high compression, and hence good confinement, is essential to achieving high yields in inertial confinement fusion implosions. In pursuit of multi-megajoule yields on the National Ignition Facility (NIF), a new campaign has begun aimed at testing the hypothesis that controlling hydrodynamic stability is key to achieving effective higher compression with the high density carbon ablators currently fielded on NIF. This campaign is built around a new implosion design, called SQ-n, that is derived from the uniquely stable Bigfoot design tested on NIF in 2016–2019. While very stable and with performance that was quite close to one-dimensional expectations, Bigfoot was a relatively high adiabat, and consequently lower compression design. The goal of SQ-n is then to evolve Bigfoot toward a higher compression design but without compromising its unique stability characteristics. Specifically, SQ-n adopts a ramped foot pulse shape to minimize early time Richtmyer–Meshkov instability growth and uses an ablator dopant distribution extending all of the way to the fuel–ablator interface that simulations suggest further reduces perturbation growth. In conclusion, this paper describes the design philosophy pursued with SQ-n, the results of instability modeling of the candidate design, and the experimental campaign planned to test these ideas in the near future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Reduced scale stripline platform to extend accessible pressures on the Z machine: Shockless compression of platinum to 650 GPa

Reaching astrophysically relevant high energy density (HED) material states in the laboratory is an ongoing effort at multiple experimental facilities. We have developed a new dynamic compression platform for the Z Pulsed Power Facility that allows for sample sizes 100s of [Formula: see text]m in thickness that accommodate multiple grains in order to fully capture bulk properties, such as material strength. A pair of experiments compressed platinum (Pt) to HED conditions and conventional inverse Lagrangian analysis as well as a recent Bayesian calibration technique were used to determine the principal isentrope to 650 GPa with density uncertainties of <2%. These low uncertainties are calculated for single sample experiments, presenting the possibility of even smaller experimental uncertainties with multiple samples the platform allows. Our new platform extends the accessible Pt ramp pressures achievable on the Z machine to over 80% of the pressure recently achieved using the National Ignition Facility planar Hohlraum platform. This new capability, the next generation evolution of the stripline platform, was made possible by advancements in both our understanding of the Z pulsed power driver and our overall magnetohydrodynamic modeling capabilities.

Porwitzky, Andrew↗
DOE OSTI2022

Controlled compositional gradients of electroformed gold and silver

Motivated by an interest in high-pressure research, thick (>1 mm) compositionally graded gold/silver (Au/Ag) films were electroformed. Systematic studies were performed to understand the role of processing temperature on the nucleation and growth kinetics and associated microstructure. Furthermore, as the electrolyte composition is continuously changing during the experiment, systematic studies were performed to correlate electrochemical parameters with film morphology and composition. In this work, the results showed that the nucleation pathways and relative deposition rate of Au and Ag are heavily dependent on the processing temperature. A procedure to ramp the temperature while continuously pumping an Au electrolyte into an initial Ag electrolyte to produce the graded film is presented. The obtained film is comprised of a segment of pure Au followed by a complete compositional gradient and ending with a segment of pure Ag across 1.5 mm. The results presented here describe a general framework to fabricate gradients of other materials through electrodeposition.

36 MATERIALS SCIENCE↗