SEARCH · Engineering Papers

Results for “protective layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Metallic seal for thermal barrier coating systems

The invention is particularly concerned with sealing thermal barrier coating systems of the type in use and being contemplated for use in diesel and other internal combustion engines. The invention also would find application in moderately high temperature regions of gas turbine engines and any other application employing a thermal barrier coating at moderate temperatures. Ni-35Cr-6Al-1Y, Ni-35Cr-6Al-1Yb, or other metallic alloy denoted as MCrAlx is applied over a zirconia-based thermal barrier overlayer. The close-out layer is glass-bead preened to densify its surface. This seals and protects the thermal barrier coating system.

Miller, Robert A.↗

NASA NTRS1993

Lunar surface operations. Volume 1: Lunar surface emergency shelter

The lunar surface emergency shelter (LSES) is designed to provide survival-level accommodations for up to four astronauts for a maximum of five days. It would be used by astronauts who were caught out in the open during a large solar event. The habitable section consists of an aluminum pressure shell with an inner diameter of 6 ft. and a length of 12.2 ft. Access is through a 4 in. thick aluminum airlock door mounted at the rear of the shelter. Shielding is provided by a 14.9 in. thick layer of lunar regolith contained within a second, outer aluminum shell. This provides protection against a 200 MeV event, based on a 15 REM maximum dose. The shelter is self-contained with a maximum range of 1000 km. Power is supplied by a primary fuel cell which occupies 70.7 cu ft. of the interior volume. Mobility is achieved by towing the shelter behind existing lunar vehicles. It was assumed that a fully operational, independent lunar base was available to provide communication support and tools for set-up and maintenance. Transportation to the moon would be provided by the proposed heavy lift launch vehicle. Major design considerations for the LSES were safety, reliability, and minimal use of earth materials.

Shields, William↗

NASA NTRS2005

Thermal, Radiation and Impact Protective Shields (TRIPS) for Robotic and Human Space Exploration Missions

New concepts for protective shields for NASA s Crew Exploration Vehicles (CEVs) and planetary probes offer improved mission safety and affordability. Hazards include radiation from cosmic rays and solar particle events, hypervelocity impacts from orbital debris/ micrometeorites, and the extreme heating environment experienced during entry into planetary atmospheres. The traditional approach for the design of protection systems for these hazards has been to create single-function shields, i.e. ablative and blanket-based heat shields for thermal protection systems (TPS), polymer or other low-molecular-weight materials for radiation shields, and multilayer, Whipple-type shields for protection from hypervelocity impacts. This paper introduces an approach for the development of a single, multifunctional protective shield, employing nanotechnology- based materials, to serve simultaneously as a TPS, an impact shield and as the first line of defense against radiation. The approach is first to choose low molecular weight ablative TPS materials, (existing and planned for development) and add functionalized carbon nanotubes. Together they provide both thermal and radiation (TR) shielding. Next, impact protection (IP) is furnished through a tough skin, consisting of hard, ceramic outer layers (to fracture the impactor) and sublayers of tough, nanostructured fabrics to contain the debris cloud from the impactor before it can penetrate the spacecraft s interior.

Loomis, M. P.↗

NASA NTRSDate not supplied

Alternative MMOD Shielding Concepts

A core objective of the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) group is to improve spacecraft meteoroid and orbital debris (MMOD) shielding by evaluating new materials and shielding concepts by test and analysis. This paper describes hypervelocity impact tests that were performed over several years to evaluate alternative MMOD shielding concepts. Specific objectives of the work were to incorporate improved MMOD and radiation protection within Stuffed Whipple shields, and to evaluate various self-sealing MMOD shielding concepts. The tests were performed under similar impact conditions and with fixed shield standoff and comparable overall shield mass. Damage to the rear wall was quantified and compared to determine the best performing shield concepts. Generally, the best shielding for both MMOD and radiation protection included polymer materials rich in hydrogen introduced into the intermediate and final layers of the shielding. In the self-sealing material evaluations, the test objective was to gauge the ability of different materials and techniques to stop leaks in a rear wall with a delta-pressure across the wall typical of spacecraft crew cabins (i.e., up to 1 atmosphere pressure). Shielding containing ionomer films and elastomer materials satisfied this objective for pressure shell holes up to 6mm diameter. This paper provides results of the investigations.

Orbital Debris↗

NASA NTRSDate not supplied

Experimental Investigations into the Material Response of Heatshields, High-Temperature Coatings, and Meteors.

Phenolic Impregnated Carbon Ablator (PICA) gained heritage during the Stardust mission and is the baseline thermal protection system (TPS) material for missions to Mars. However, PICA is friable, so a thin layer of siloxane resin (NuSil) is applied to the surface of the heatshield to suppress the spread of particulate matter during cleanroom activities. Until recently, the thermochemical response of NuSil had not been accounted for in material response models. Therefore, a test campaign was executed at the Hypersonic Materials Environmental Test System (HyMETS) facility to investigate the material response of NuSil and provide crucial insight for model development. Finally, salient results from an experiment supported by the Asteroid Threat Assessment Project (ATAP) will be discussed, which probed the material response of the Tamdakht meteorite and notable analogs. Bio: Dr. Bessire is a senior research scientist in the thermal protection system materials branch at the NASA Ames Research Center. His research focuses on developing analytical techniques designed to inform and validate the development of material response models.

Brody K. Bessire↗

NASA NTRS2000

Thermal Insulation Performance of Textile Structures for Spacesuit Applications at Martian Pressure and Temperature

Protection of astronauts from the extreme temperatures in the space environment has been provided in the past using multi-layer insulation in ultra-high vacuum environments of low earth orbit and the lunar surface. For planetary environments with residual gas atmospheres such as Mars with ambient pressures between 8 to 14 hPa (8 to 14 mbar), new protection techniques are required because of the dominating effect of the ambient gas on heat loss through the insulation. At Mars ambient pressure levels, the heat loss can be excessive at expected suit external temperatures of 172 K with state-of-the-art suit insulation, requiring an active heat source and its accompanying weight and volume penalties. Micro-fibers have been identified as one potential structure to reduce the heat losses, but existing fundamental data on fiber heat transfer at low pressure is lacking for integrated fabric structures. This baseline study presents insulation performance test data at different pressures and fabric loads for selected polyesters and aramids as a function of fiber density, fiber diameter, fabric density, and fabric construction. A set of trend data of thermal conductivity versus ambient pressure is presented for each fiber and fabric construction design to identify the design effects on thermal conductivity at various ambient pressures, and to select a fiber and fabric design for further development as a suit insulation. The trend data also shows the pressure level at which thermal conductivity approaches a minimum, below which no further improvement is possible for a given fiber and fabric design. The pressure levels and resulting thermal conductivities from the trend data can then be compared to the ambient pressure at a planetary surface, Mars for example, to determine if a particular fiber and fabric design has potential as a suit insulation.

Orndoff, Evelyne↗

NASA NTRS2009

Orbiter Boundary Layer Transition Stability Modeling at Flight Entry Conditions

State of the art boundary layer stability modeling capabilities are increasingly seeing application to entry flight vehicles. With the advent of user friendly and robust implementations of two-dimensional chemical nonequilibrium stability modeling with the STABL/PSE-CHEM software, the need for flight data to calibrate such analyses capabilities becomes more critical. Recent efforts to perform entry flight testing with the Orbiter geometry related to entry aerothermodynamics and boundary layer transition is allowing for a heightened focus on the Orbiter configuration. A significant advancement in the state of the art can likely be achieved by establishing a basis of understanding for the occurrence of boundary layer transition on the Orbiter due to discrete protruding gap fillers and the nominal distributed roughness of the actual thermal protection system. Recent success in demonstrating centerline two-dimensional stability modeling on the centerline of the Orbiter at flight entry conditions provides a starting point for additional investigations. The more detailed paper will include smooth Orbiter configuration boundary layer stability results for several typical orbiter entry conditions. In addition, the numerical modeling approach for establishing the mean laminar flow will be reviewed and the method for determining boundary layer disturbance growth will be overviewed. In addition, if actual Orbiter TPS surface data obtained via digital surface scans become available, it may be possible to investigate the effects of an as-flown flight configuration on boundary layer transition compared to a smooth CAD reference.

Bartkowicz, Matt↗

NASA NTRS2011

Assessment of Resistance of Bacillus Horneckiae Endospores to UV Radiation and Function of Their Extraneous Layer in Resistance

Spore-forming microbes are highly resistant to various physical and chemical conditions, which include ionizing and UV radiation, desiccation and oxidative stress, and the harsh environment of outer space or planetary surfaces. The spore's resistance might be due to their metabolically dormant state, and/or by the presence of a series of protective structures that encase the interior-most compartment, the core, which houses the spore chromosome. These spores have multiple layers surrounding the cell that are not found in vegetative cells, and some species have an outer layer of proteins and glycoproteins termed the "exosporium" or a fibrous "extraneous layer" (EL). Bacillus horneckiae is an EL-producing novel sporeformer isolated from a Phoenix spacecraft assembly clean room, and it has previously demonstrated resistance to UV radiation up to 1000 J/m(sup 2). The EL appears to bind B. horneckiae spores into large aggregations, or biofilms, and may confer some UV resistance to the spores. Multiple culturing and purification schemes were tried to achieve high purity spores because vegetative cells would skew UV resistance results. An ethanol-based purification scheme produced high purity spores. Selective removal of the EL from spores was attempted with two schemes: a chemical extraction method and physical extraction (sonication). Results from survival rates in the presence and absence of the external layer will provide a new understanding of the role of biofilms and passive resistance that may favor survival of biological systems in aggressive extra-terrestrial environments. The chemical extraction method decreased viable counts of spores and lead to an inconclusive change UV resistance relative to non-extracted spores. The physical extraction method lead to non-aggregated spores and did not alter viability; however, it produced UV resistance profiles similar to non-extracted spores. In addition to the EL-removal study, samples of B. horneckiae spores dried on aluminum coupons and exposed to increasing UV (200-400 nm range) levels (0 to 8.0 x 105 kJ/m(sup 2)) were tested for viability, which indicated that the maximum UV exposure level that still resulted in viable spores was 5.0 x 10? kJ/m(sup 2).

resistance↗

NASA NTRS2006

Thermal Challenge for Sun-Viewing Instruments on Solar Probe 3 R(sub s) from Sun

The Solar Probe science team at NASA GSFC is considering enhance science observations by adding the nadir viewing Plasma Spectrometer instrument and using heat shields to protect the Plasma Wave antennas to permit full extension at 3 R. The electrostatic mirror of the Plasma Spectrometer is thermally protected from the Sun by a miniature sunshield that consists of two carbon-carbon composite layers, and a much smaller carbon-carbon heat shield. The sun-viewing surface of the miniature sunshield has an Al2O3 thin film coating. The slope of the sunshield is minimized to the smallest possible extent so that it can still accommodate the elliptical electrostatic mirror. Two small MLI flaps minimize the heat radiation from the Plasma Spectrometer to the spacecraft bus. This design meets the thermal requirements. Each of the four Plasma Wave wire antennas is 5 m long, and thermally protected from the Sun by a sunshield. The sunshield consists of two carbon-carbon composite sheets. One sheet views the Sun, and one does not. The slope of most of the sun-viewing sheet is 23deg with the nadir axis. For mechanical reason, it gradually increases to 37.5deg at the tip. The exterior of the sun viewing surfaces has a thin film of Al2O3. The exterior of the shaded sheets has a thin film of vapor deposited rhodium. It minimizes the heat radiation to the spacecraft bus. A high temperature MLI blanket between the carbon-carbon sheets radiatively isolates them. The thermal design meets the temperature requirements, but exceeds the 20 W limit of heat radiation to the spacecraft bus by 20 W. Thermal options to reduce the heat radiation include reducing the alpha to epsilon ratio of the Al2O3 thin film and reducing the number of antennas to three. Testing in 2006 includes thermal model validation and materials testing. High temperature ovens and a high light intensity Vortex Lamp will be used.

Choi, Michael K.↗

NASA NTRS1985

Mixing layer control for tangential slot injection in turbulent flows

Tangential injection into turbulent flows is one of the most promising methods of minimizing skin friction and providing thermal protection. The technique also has application to laser hardening. The effectiveness of the injected material can be increased if the spreading rate of the resulting mixing region can be reduced. Various techniques which have been shown to be effective in manipulating the rate of growth of mixing layers under certain conditions have been applied to a slot configuration having a thick external turbulent boundary layer. These include geometry modifications to the slot lip trailing edge and acoustic excitation of the slot exit plane over a wide range of frequencies. Neither of these approaches produced any noticeable effect on the downstream evolution of the mixing layer. This lack of effectiveness is attributed to the dominating influence of the well-developed incoming turbulent boundary layer. The placement of large-eddy breakup devices in this boundary layer upstream of the injection point did produce significantly lower velocities in the near-wall region of the flow downstream of the slot exit.

Mcinville, R. M.↗

NASA NTRS1973

An analysis of a charring ablator with thermal nonequilibrium, chemical kinetics, and mass transfer

The differential equations governing the transient response of a one-dimensional ablative thermal protection system are presented for thermal nonequilibrium between the pyrolysis gases and the char layer and with finite rate chemical reactions occurring. The system consists of three layers (the char layer, the uncharred layer, and an optical insulation layer) with concentrated heat sinks at the back surface and between the second and third layers. The equations are solved numerically by using a modified implicit finite difference scheme to obtain solutions for the thickness of the charred and uncharred layers, surface recession and pyrolysis rates, solid temperatures, porosity profiles, and profiles of pyrolysis-gas temperature, pressure, composition, and flow rate. Good agreement is obtained between numerical results and exact solutions for a number of simplified cases. The complete numerical analysis is used to obtain solutions for an ablative system subjected to a constant heating environment. Effects of thermal, chemical, and mass transfer processes are shown.

Clark, R. K.↗

NASA NTRS1974

Method of protecting the surface of a substrate

The surface of a metallic base system is initially coated with a metallic alloy layer that is ductile and oxidation resistant. An aluminide coating is then applied to the metallic alloy layer. The chemistry of the metallic alloy layer is such that the oxidation resistance of the subsequently aluminized outermost layer is not seriously degraded.

Gedwill, M. A.↗

NASA NTRS1977

Plasma polymerized coating for polycarbonate - Single layer, abrasion resistant, and antireflection

Plasma polymerized vinyltrimethoxy silane films were deposited on transparent polycarbonate substrates. The adherent, clear films protected the substrates from abrasion and also served as antireflection coatings. Posttreatment of the vinyltrimethoxy silane films in an oxygen glow discharge further improved the abrasion resistance. ESCA (electron spectroscopy for chemical analysis) and IR transmission spectra of some films were recorded, and an elemental analysis of the films was obtained.

Wydeven, T.↗

NASA NTRS1998

Environmentally friendly anti-icing

The present invention describes an aqueous, non-electrolytic, non-toxic, biodegradable, continuous single phase liquid anti-icing or deicing composition for use on the surfaces of, for example, aircraft, airport pavements, roadways, walkways, bridges, entrances, structures, canals, locks, components, vessels, nautical components, railroad switches, and motor vehicles. The anti-icing or deicing composition comprises: (a) water; (b) a non-toxic freezing point depressant selected from the group consisting of monohydric alcohols having from 2 to 6 carbon atoms, polyhydric alcohols having from 3 to 12 carbon atoms, monomethyl or ethyl ethers of polyhydric alcohols having from 3 to 12 atoms or mixtures thereof, wherein the freezing point depressant present is between about 14 to 60 percent by weight; (c) a thickener which is present in between about 0.01 and 10 percent by weight; and (d) optionally a corrosion inhibitor which is present in between about 0.01 and 0.1 percent by weight of the total composition. In one embodiment, the deicing composition further includes (e) a monohydric primary aliphatic unbranched alcohol as a means of forming a thin layer of the composition on the surface of the structure to be given ice protection, and/or as means of forming a homogenized foam with xanthan thickener; which alcohol is selected from the group consisting of alcohols having between 8 to 24 carbon atoms, preferably, 1-dodecanol. Compositions of water, propylene glycol, and/or propanol and xanthan are preferred.

Lockyer, Robert T.↗

NASA NTRS2008

RF MEMS Switches with SiC Microbridges for Improved Reliability

Radio frequency (RF) microelectromechanical (MEMS) switches offer superior performance when compared to the traditional semiconductor devices such as PIN diodes or GaAs transistors. MEMS switches have a return loss (RL) better than -25 dB, negligible insertion loss (IL), isolation better than -30 dB, and near zero power consumption. However, RF MEMS switches have several drawbacks the most serious being long-term reliability. The ability for the switch to operate for millions or even billions of cycles is a major concern and must be addressed. MEMS switches are basically grouped in two categories, capacitive and metal-to-metal contact. The capacitive type switch consists of a movable metal bridge spanning a fixed electrode and separated by a narrow air gap and thin insulating material. The metal-to-metal contact type utilizes the same basic design but without the insulating material. After prolonged operation the metal bridges, in most of these switches, begin to sag and eventually fail to actuate. For the metal-to-metal type, the two metal layers may actually fuse together. Also if the switches are not packaged properly or protected from the environment moisture may build up and cause stiction between the top and bottom electrodes rendering them useless. Many MEMS switch designs have been developed and most illustrate fairly good RF characteristics. Nevertheless very few have demonstrated both great RF performance and ability to perform millions/billions of switching cycles. Of these, nearly all are of metal-to-metal type so as the frequency increases RF performance decreases.

Scardelletti, Maximilian C.↗

NASA NTRS2004

Electrochemical Properties of Organosilane Self Assembled Monolayers on Aluminum 2024

Self assembled monolayers are commonly used to modify surfaces. Within the last 15 years, self assembled monolayers have been investigated as a way to protect from corrosion[1,2] or biofouling.[3] In this study, self assembled monolayers of decitriethoxysilane (C10H21Si(OC2H5)3) and octadecyltriethoxysilane (C18H37Si(OC2H5)3) were formed on aluminum 2024-T3. The modified surfaces and bare Al 2024 were characterized by dynamic water contact angle measurements, x-ray photoelectron spectroscopy (XIPS) and infrared spectroscopy. Electrochemical impedance spectroscopy (EIS) in 0.5 M NaCl was used to characterize the monolayers and evaluate their corrosion protection properties. The advancing water contact angle and infrared measurements show that the mono layers form a surface where the hydrocarbon chains are packed and oriented away from the surface, consistent with what is found in similar systems. The contact angle hysteresis measured in these systems is relatively large, perhaps indicating that the hydrocarbon chains are not as well packed as monolayers formed on other substrates. The results of the EIS measurements were modeled using a Randle's circuit modified by changing the capacitor to a constant phase element. The constant phase element values were found to characterize the monolayer. The capacitance of the monolayer modified surface starts lower than the bare Al 2024, but approaches values similar to the bare Al 2024 within 24 hours as the monolayer is degraded. The n values found for bare Al 2024 quickly approach the value of a true capacitor and are greater than 0.9 within hours after the start of exposure. For the monolayer modified structure, n can stay lower than 0.9 for a longer period of time. In fact, n for the monolayer modified surfaces is different from the bare surface even after the capacitance values have converged. This indicates that the deviation from ideal capacitance is the most sensitive indicator of the presence of the monolayer.

Hintze, Paul E.↗

NASA NTRS2016

IADC Vulnerability Report, IT32-21

Numerous mission support hardware systems and their spares are maintained outside of the habitable volume of the International Space Station (ISS), and are arranged covered by a multi-layer insulation (MLI) thermal blanket which provides both thermal control and a measure of protection from micrometeoroids and orbital debris (MMOD). The NASA Hypervelocity Impact Technology (HVIT) group at the Johnson Space Center in Houston Texas has assessed the protection provided by MLI in a series of hypervelocity impact tests using a 1 mm thick aluminum 6061-T6 rear wall to simulate the actual hardware behind the MLI. HVIT has also evaluated methods to enhance the protection provided by MLI thermal blankets. The impact study used both aluminum and steel spherical projectiles accelerated to speeds of 7 km/s using a 4.3 mm, two-stage, light-gas gun at the NASA White Sands Test Facility (WSTF).

Christiansen, E. L.↗

NASA NTRS1991

Helmet of a laminate construction of polycarbonate and polysulfone polymeric material

An article of laminate construction is disclosed which is comprised of an underlayer of polycarbonate polymer material to which is applied a chemically resistant outer layer of polysulfone. The layers which are joined by compression-heat molding, are molded to form the shape of a body protective shell such as a space helmet comprising a shell of polycarbonate, polysulfone laminate construction attached at its open end to a sealing ring adapted for connection to a space suit. The front portion of the shell provides a transparent visor for the helmet. An outer visor of polycarbonate polysulfone laminate construction is pivotally mounted to the sealing ring for covering the transparent visor portion of the shell during extravehicular activities. The polycarbonate under layer of the outer visor is coated on its inner surface with a vacuum deposit of gold to provide additional thermal radiation resistance.

Kosmo, Joseph J.↗