SEARCH · Engineering Papers

Results for “power coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1979

T700 power turbine rotor multiplane/multispeed balancing demonstration

Research was conducted to demonstrate the ability of influence coefficient based multispeed balancing to control rotor vibration through bending criticals. Rotor dynamic analyses were conducted of the General Electric T700 power turbine rotor. The information was used to generate expected rotor behavior for optimal considerations in designing a balance rig and a balance technique. The rotor was successfully balanced 9500 rpm. Uncontrollable coupling behavior prevented observations through the 16,000 rpm service speed. The balance technique is practical and with additional refinement it can meet production standards.

Burgess, G.↗

NASA NTRS1979

Relationship between hurricane surface winds and L-band radar backscatter from the sea surface

High-altitude, airborne, L-band synthetic aperture radar (SAR) data were collected in Hurricane Gloria on 28 and 30 September 1976. The backscattered power levels (proportional to the surface scattering coefficient) averaged over a few square kilometers of surface area were found to vary with surface wind speed and the angle of the wind relative to the radar. Comparisons between the backscatter from the eye and eye-wall regions of the hurricane were made with low-level aircraft wind measurements that were nearly coincident in space and time. The SAR has the potential advantage over other radar types because of its higher spatial resolution. It also appears to have the ability to penetrate rainfall, with a reduction in the echo from the surface. One difference when compared with higher frequency microwave radars is a decrease in the sensitivity of the backscatter to changes in wind speed. This dependence of L-band radar backscatter on surface winds suggests that the winds associated with hurricanes can be measured with airborne or spaceborne radars.

Weissman, D. E.↗

NASA NTRS1979

Solubility of noble gases in serpentine - Implications for meteoritic noble gas abundances

An investigation of the solubilities of the noble gases from synthesis and solubility studies of the sheet silicate mineral serpentine in carbonaceous chondrites is presented. Hydrothermal synthesis and exchange experiments were made at 340C and 1 kbar with noble gas partial pressures from 2 times 10 to the -8th power to 0.1 atm. The measured distribution coefficients for noble gases are not sufficiently high to account for the trapped noble gases in carbonaceous chondrites by exchange in solar nebula if meteoritic minerals have comparable distribution coefficients. Also, serpentine gains and loses noble gases to approach equilibrium values with the terrestrial atmosphere, indicating that this exposure may have influenced the noble gas abundances in phyllosilicate minerals of these chondrites. The dispersion of K-Ar ages of carbonaceous chondrites could be the result of phyllosilicates approaching equilibrium solubility of atmospheric Ar-40.

Zaikowski, A.↗

NASA NTRS1980

The washout of combustion-generated hydrogen chloride

The coefficient for the washout from a rocket exhaust cloud of HCl generated by the combustion of an ammonium perchlorate-based solid rocket propellant such as that to be used for the Space Shuttle Booster is determined. A mathematical model of HCl scavenging by rain is developed taking into account rain droplet size, fall velocity and concentration under various rain conditions, partitioning of exhaust HCl between liquid and gaseous phases, the tendency of HCl to promote water vapor condensation and the concentration and size of droplets within the exhaust cloud. The washout coefficient is calculated as a function of total cloud water content, total HCl content at 100% relative humidity, condensation nuclei concentration and rain intensity. The model predictions are compared with experimental results obtained in scavenging tests with solid rocket exhaust and raindrops of different sizes, and the large reduction in washout coefficient at high relative humidities predicted by the model is not observed. A washout coefficient equal to 0.0000512 times the -0.176 power of the mass concentration of HCl times the 0.773 power of the rainfall intensity is obtained from the experimental data.

Fenton, D. L.↗

NASA NTRS1987

The interaction of solar p-modes with a sunspot. II - Simple theoretical models

The interaction of solar p-modes with a sunspot magnetic flux tube is investigated theoretically by means of two simple models. An increase in horizontal wavelength between the nonmagnetic and magnetic regions, due to the different characteristic wave speeds in the two regions, explains the corresponding observed wavelength shift of powe in the umbral k-omega power spectrum. The variation of the transmission coefficient with wavenumber along the p-mode diagnostic curves, due to resonant transmission, is responsible for the observed selective filtering of the p-modes by the sunspot.

Abdelatif, Toufik E.↗

NASA NTRS1987

A parametric study of mean loading effects on airfoil gust interaction noise

The influence of airfoil mean loading parameters on the sound generated by interaction with short wavelength vorticity and entropy gusts is examined. It is found that there are two mean flow parameters of importance, the effective leading edge incidence angle and the airfoil lift coefficient. The former controls the total sound power level, while the latter has an important effect on the directivity pattern. For vorticity gusts, positive gust angles result in noise levels which increase with leading edge loading (LEL), while for negative gust angles an increase in LEL may actually reduce the noise level. For low levels of LEL, entropy gusts generate less sound than vorticity gusts, while for larger values of LEL, entropy gusts are at least as important as vorticity gusts.

Kerschen, E. J.↗

NASA NTRS1950

Effects of the Lateral Oscillation of Fixing the Rudder and Reflexing the Flaps on the Bell X-1 Airplane

Flight tests have been made on the Bell X-1 airplane having the 10-percent-thick wing and the 8-percent-thick tail to evaluate the effects of fixing the rudder and changing the inclination of the principal axes of inertia by reflexing the landing flaps on the snaking which has been encountered over practically the entire range of Mach number and normal-force coefficient. The data were obtained during power-off glides at altitudes between 32,000 and 16,000 feet. The results showed that fixing the rudder reduced the amplitude of the snaking, but did not eliminate it at a Mach number of 0.84. It was also found that reflexing the flaps to change the inclination of the principal axis of inertia 1 ¾° nose up increased the dynamic lateral stability, but had only a small effect on the snaking oscillation at a Mach number of 0.85.

Hubert M Drake↗

NASA NTRS2002

Survey of Beamed Energy Propulsion Concepts by the MSFC Space Environmental Effects Team

This will be a survey paper of work that was performed by the Space Environmental Effects Team at NASA's Marshall Space Flight Center in the area of laser energy propulsion concepts. Two types of laser energy propulsion techniques were investigated. The first was ablative propulsion, which used a pulsed ruby laser impacting on single layer coatings and films. The purpose of this investigation was to determine the laser power density that produced an optimum coupling coefficient for each type of material tested. A commercial off-the-shelf multi-layer film was also investigated for possible applications in ablative micro-thrusters, and its optimum coupling coefficient was determined. The second type of study measured the purely photonic force provided by a 300W CW YAG laser. In initial studies, the photon force resulting from the momentum of incident photons was measured directly using a vacuum compatible microbalance and these results were compared to theory. Follow-on work used the same CW laser to excite a stable optical cavity for the purpose of amplifying the available force from incident photons.

Gray, P. A.↗

NASA NTRS1961

Transonic Loads Characteristics of a 3-Percent-Thick 60 deg Delta-Wing-Body

An investigation has been made in the Langley 16-foot transonic tunnel to determine the aerodynamic loading characteristics of a 3-percent-thick, aspect-ratio - 2.06, 60 deg delta-wing-body combination. The Mach number range was from 0.80 t o 1.05 and the average Reynolds number based on wing mean aerodynamic chord was 10 x 10(exp 6). The angle-of-attack range was from 0 deg to 26 deg but was limited at the highest Mach numbers by tunnel drive power. Pressure distributions, spanwise loadings, integrated wing coefficients, and tabulated pressure coefficients are presented for the range of Mach numbers and angles of attack. The results indicate that a free leading-edge separation vortex is the dominant flow-field phenomenon at all Mach numbers and that, consequently, there are only slight changes in the spanwise loadings with Mach number. There is a slight outboard shift in center of pressure with an increase in Mach number. The chord-wise position of the center of pressure varies from 46 t o 55 percent of the mean aerodynamic chord when the Mach number i s increased from 0.80 to l.05.

Swihart, John M.↗

NASA NTRS1956

Flight Investigation to Determine the Effect of Jet Exhaust on Drag, Trim Characteristics, and Afterbody Pressures of a 0.125-Scale Rocket Model of the Mcdonnell F-101A Airplane

A flight investigation was conducted to determine the effect of jet exhaust on the drag, trim characteristics, and afterbody pressures on a 0.125-scale rocket model of the McDonnell F-101A airplance. Power-off data were obtained over a Mach number range of 1.04 to 1.9 and power-on data were obtained at a Mach number of about 1.5. The data indicated that with power-on the change in external drag coefficient was within the data accuracy and there was a decrease in trim angle of attack of 1.27 degrees with a corresponding decrease of 0.07 in lift coefficient. Correspondingly, pressure coefficients on the side and bottom of the fuselage indicated a positive increment near the jet exit. As the distance downstream of the jet exit increased, the increment on the bottom of the fuselage increased, whereas the increments on the side decreased to a negative peak.

Kennedy, Thomas L.↗

NASA NTRS1982

A technique for determining powered-lift STOL aircraft performance at sea level from flight data taken at altitude

State-of-the-technology powered-lift STOL aircraft can develop very high lift coefficients. The determination of how this high lift capability can be utilized for landing approaches is accomplished by evaluating aircraft velocity versus flightpath performance. This paper briefly discusses upper-surface-blowing power-lift technology and some of the significant features of the velocity versus flightpath plot that are used in evaluating the performance of powered-lift aircraft. A procedure for deriving the velocity versus flightpath plot for a powered-lift aircraft at any specified weight at sea level, based on flight-test data obtained at various weights and altitudes, is discussed in detail. Actual flight-test data obtained with NASA's Quiet Short-Haul Research Aircraft (QSRA) are used to illustrate this procedure and to evaluate the results.

Stevens, V. C.↗

NASA NTRSDate not supplied

Evaluation of Heat Transfer Coefficient from Velocity Distribution in Boundary Layer

This paper describes a method of evaluating heat transfer coefficient from a velocity distribution in the boundary layer. The power law velocity profile and universal velocity distribution in a smooth pipe have been used to evaluate the wall shear stress, and the heat transfer coefficient was evaluated from the wall shear stress using the Chilton-Colburn analogy. The predicted pressure drop was compared with the pressure drop computed by the Colebrook equation, and the predicted heat transfer coefficient was compared with the heat transfer coefficient calculated by the Dittus-Boelter equation. The accuracy of pressure drop prediction was within 1%, and the accuracy of heat transfer coefficient prediction was within 8%. This method has the potential to use a Navier-Stokes based CFD solution to evaluate the heat transfer coefficient in nodal or network flow codes.

Heat Transfer Coefficient↗

NASA NTRSDate not supplied

Evaluation of Heat Transfer Coefficient from Velocity Distribution in Boundary Layer

Heat Transfer Coefficient↗

NASA NTRS1987

Wind tunnel test IA300 analysis and results, volume 1

The analysis and interpretation of wind tunnel pressure data from the Space Shuttle wind tunnel test IA300 are presented. The primary objective of the test was to determine the effects of the Space Shuttle Main Engine (SSME) and the Solid Rocket Booster (SRB) plumes on the integrated vehicle forebody pressure distributions, the elevon hinge moments, and wing loads. The results of this test will be combined with flight test results to form a new data base to be employed in the IVBC-3 airloads analysis. A secondary objective was to obtain solid plume data for correlation with the results of gaseous plume tests. Data from the power level portion was used in conjunction with flight base pressures to evaluate nominal power levels to be used during the investigation of changes in model attitude, eleveon deflection, and nozzle gimbal angle. The plume induced aerodynamic loads were developed for the Space Shuttle bases and forebody areas. A computer code was developed to integrate the pressure data. Using simplified geometrical models of the Space Shuttle elements and components, the pressure data were integrated to develop plume induced force and moments coefficients that can be combined with a power-off data base to develop a power-on data base.

Kelley, P. B.↗

NASA NTRS1988

High-resolution spectra and photoabsorption coefficients for carbon monoxide absorption bands between 94.0 nm and 100.4 nm

Photoabsorption coefficients have been measured for the CO in interstellar clouds at a resolving power more than 20 times greater than previously obtainable. In order to facilitate comparisons, these data have been integrated over the same wavelength ranges as used in Letzelter et al. (1987). It is found that most of the results obtained for bands between 94.0 and 100.4 nm are larger than those of Letzelter; the discrepancy may be attributable to the difference between the resolving powers of the spectrometers used, because the saturation effects associated with low resolution can underestimate absorption coefficient values.

Yoshino, K.↗

DOE OSTI2020

Revisiting Theoretical Limits for One-Degree-of-Freedom Wave Energy Converters: Preprint

This work revisits the theoretical limits of one-degree of freedom wave energy converters (WECs). This paper considers the floating sphere used in the Ocean Energy Systems (OES) Task 10 Wave Energy Converter modeling and verification effort for analysis. Analytical equations are derived to determine bounds on the motion amplitude, time-averaged power, and power take-off (PTO) force. A unique result was found that shows the time-averaged power absorbed by a WEC can be defined solely by the inertial properties and the radiation hydrodynamic coefficients. In addition, a unique expression for the PTO force amplitude was derived which has provided upper and lower bounds when resistive control is used to maximize power generation. For complex conjugate control, this same expression can only provide a lower bound as there is theoretically no upper bound. These bounds are used to compare the performance of a floating sphere if it were to extract energy using surge or heave motion. The analysis shows that because of the differences in hydrodynamic coefficients of each oscillating mode there will be different frequency ranges that provide better power capture efficiency. The influence of a motion constraint on power absorption while also utilizing a nonideal power take-off is examined and found to reduce the losses associated with bidirectional energy flow. The expression to calculate the time-averaged power with a nonideal PTO is modified by the mechanical-to-electrical efficiency and the ratio of the PTO spring and damping coefficients. These were separated in the expression which allows for limits to be set on the possible values of PTO coefficients to ensure a net flow of power to the grid.

50 EE - Wind and Water Power Program - Water (EE-4↗

DOE OSTI2022

Application of the bRapid fission matrix burnup methodology to the JSI TRIGA Mark II research reactor

The novel burnup methodology, bRAPID, of the RAPID code system has been applied to the TRIGA Mark II research reactor at the 'Jozef Stefan' Institute. This paper presents the first step in our goal for on-line determination of isotope inventory and burnup, that the RAPID code system with its Fission Matrix (FM) method enables. Burnup analysis of changes in FM coefficients due to TRIGA fuel burnup at different irradiation times and specific power distribution in the reactor core is presented. Our results demonstrate that primary contribution for changes of FM coefficients is the burnup of the destination s, while the spectrum differences, that arise due to fuel's core location, have negligible effect on FM coefficients. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1999

Selection of Optical Glasses Using Buchdahl's Chromatic Coordinate

This investigation attempted to extend the method of reducing the size of glass catalogs to a global glass selection technique with the hope of guiding glass catalog offerings. Buchdahl's development of optical aberration coefficients included a transformation of the variable in the dispersion equation from wavelength to a chromatic coordinate omega defined as omega = (lambda - lambda(sub 0))/ 1 + 2.5(lambda - lambda(sub 0)) where lambda is the wavelength at which the wavelength is calculated and lambda(sub 0) is a base wavelength about which the expansion is performed. The advantage of this approach is that the dispersion equation may be written in terms of a simple power series and permits direct calculation of dispersion coefficients. While several promising examples were given, a systematic application of the technique to an entire glass catalog and analysis of the subsequent predictions was not performed. The goal of this work was to apply the technique in a systematic fashion to glasses in the Schoft catalog and assess the quality of the predictions.

Griffin, DeVon W.↗