Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Space infrared telescope facility wide field and diffraction limited array camera (IRAC)

The wide-field and diffraction limited array camera (IRAC) is capable of two-dimensional photometry in either a wide-field or diffraction-limited mode over the wavelength range from 2 to 30 microns with a possible extension to 120 microns. A low-doped indium antimonide detector was developed for 1.8 to 5.0 microns, detectors were tested and optimized for the entire 1.8 to 30 micron range, beamsplitters were developed and tested for the 1.8 to 30 micron range, and tradeoff studies of the camera's optical system performed. Data are presented on the performance of InSb, Si:In, Si:Ga, and Si:Sb array detectors bumpbonded to a multiplexed CMOS readout chip of the source-follower type at SIRTF operating backgrounds (equal to or less than 1 x 10 to the 8th ph/sq cm/sec) and temperature (4 to 12 K). Some results at higher temperatures are also presented for comparison to SIRTF temperature results. Data are also presented on the performance of IRAC beamsplitters at room temperature at both 0 and 45 deg angle of incidence and on the performance of the all-reflecting optical system baselined for the camera.

Fazio, Giovanni G.↗
NASA NTRS2012

Landsat Data Continuity Mission Expected Instrument Performance

The Landsat Data Continuity Mission (LDCM) is scheduled for a December 2012 launch date. LDCM is being managed by an interagency partnership between NASA and the U.S. Geological Survey (USGS). In order to provide the necessary spectral coverage of the visible through shortwave-infrared (SWIR) and the thermal-infrared (TIR), the satellite will carry two sensors. The Operational Land Imager (OLI) will collect data for nine visible to shortwave spectral bands with a spatial resolution of 30 m (with a 15 m panchromatic band). The Thermal Infrared Sensor (TIRS) will collect coincident image data for two TIR bands with a spatial resolution of 100 m. The OLI is fully assembled and tested and has been shipped by it's manufacturer, Ball Aerospace and Technology Corporation, to the Orbital Sciences Corporation (Orbital) facility where it is being integrated onto the LDCM spacecraft. Pre-launch testing indicates that OLI will meet all performance specification with margin. TIRS is in development at the NASA Goddard Space F!ight Center (GSFC) and is in final testing before shipping to the Orbital facility in January, 2012. The presentation will describe the LDCM satellite instrument systems, present pre-launch performance data for OLI and TIRS, and present simulated images to highlight notable features and expected imaging performance.

Dabney, Philip W.↗
NASA NTRS2010

Kepler Science Operations Center Architecture

We give an overview of the operational concepts and architecture of the Kepler Science Data Pipeline. Designed, developed, operated, and maintained by the Science Operations Center (SOC) at NASA Ames Research Center, the Kepler Science Data Pipeline is central element of the Kepler Ground Data System. The SOC charter is to analyze stellar photometric data from the Kepler spacecraft and report results to the Kepler Science Office for further analysis. We describe how this is accomplished via the Kepler Science Data Pipeline, including the hardware infrastructure, scientific algorithms, and operational procedures. The SOC consists of an office at Ames Research Center, software development and operations departments, and a data center that hosts the computers required to perform data analysis. We discuss the high-performance, parallel computing software modules of the Kepler Science Data Pipeline that perform transit photometry, pixel-level calibration, systematic error-correction, attitude determination, stellar target management, and instrument characterization. We explain how data processing environments are divided to support operational processing and test needs. We explain the operational timelines for data processing and the data constructs that flow into the Kepler Science Data Pipeline.

Middour, Christopher↗
DOE OSTI2023

Panorama 360 (Final Report)

This is the final technical report for the DOE-funded Panorama 360 project. Panorama 360 provided a resource for the collection, analysis, and sharing of performance data about end-to-end scientific workflows executing on DOE facilities. The work focused on workflows that include experimental data generation at DOE facilities. The main activities of Panorama 360 include the development of: 1. A distributed repository that stores different types of workflow execution data (e.g., point and time series performance traces at fine- and coarse-grained levels); 2. A set of open-source data capture, curation, and publishing tools fully integrated with a state-of-the-art workflow management system that automates data ingestion to the repository and enables users to discover, query, and process data from the repository; 3. A set of analysis algorithms and machine learning based tools to perform analysis and characterization of the gathered data, which can be used to detect anomalous performance or system faults; and 4. Best practices and recommendations for workflow evaluation, analysis, execution, and architectures.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Singleton Sieving: Overcoming the Memory/Speed Trade-Off in Exascale k-mer Analysis

Traditional filter data structures, such as Bloom filters, do not offer necessary features that modern high-performance data analytics applications need in order to efficiently perform complex data analysis tasks. For example, MetaHipMer, a de novo metagenome assembler, can use filters to weed out singleton k-mers and reduce memory usage by 30%-70%. However, the filter needs the ability to associate values with k-mers in order to perform the analysis in a single communication pass. Bloom filters do not support value associations and cause the application to perform an extra communication pass, thereby increasing the run time. Therefore, MetaHipMer faces a trade off between memory and speed due to the limited capabilities of traditional filters. In this paper, we overcome the memory and speed trade off in MetaHipMer by integrating a GPU-based feature-rich filter, the Two-Choice filter (TCF), in the MetaHipMer pipeline. The TCF uses key-value association to approximately store k-mers with extensions. This allows MetaHipMer to perform k-mer analysis on the GPUs in a single communication pass. Our empirical analysis shows a 50% reduction in memory usage in k-mer analysis on each node in MetaHipMer without any effect on the overall run time or assembly quality. The memory reduction in turn results in a 43% reduction in the number of nodes required to assemble datasets and enables MetaHipMer to scale to much larger datasets.

McCoy, Hunter↗
NASA NTRS1974

Flat-plate collector performance determined experimentally with a solar simulator

The NASA is constructing a new office building at Langley Research Center that will utilize solar energy for heating and cooling. A collector technology program is described which includes testing collectors in an indoor facility under simulated solar radiation. Tests have been conducted on five collectors to date and performance data are presented. The collector performance obtained with the solar simulator will be correlated with data obtained by conducting tests outdoors at Lewis.

Vernon, R. W.↗
NASA NTRSDate not supplied

Test and Evaluation of the Next Generation Blower for FBCO2 Scrubber

The four-bed carbon dioxide (FBCO2) scrubber was deployed on the ISS in late 2021 as a technology demonstration. The system was launched with a Honeywell blower that, while performing well, is no longer supported by the manufacturer with no available spares. Thus, NASA contracted with Calnetix Technologies to develop a next-generation, magnetic-bearing blower to meet FBCO2 demands and deliver the flowrates required for effective CO2 scrubbing. The first flight blower assembly was tested by Marshall Space Flight Center (MSFC) in the summer of 2022 and installed in FBCO2 in February 2023. This paper presents the blower performance ground testing results, with details on the test plan and test setup provided. The performance data is used not only to qualify the blower for use in F BCO2, but also to create a model for use in predictions of on-orbit performance based on available telemetry data. The paper concludes with discussions on test limitations and early FBCO2 performance data with the new blower installed.

Kaitlin Oliver-Butler↗
NASA NTRS1975

ERTS-1 data collection system: Status and performance

The Data Collection System flown on the first Earth Resources Technology Satellite (ERTS-1) relays earth resources data from remotely located in-situ sensors to Goddard Space Flight Center. Data is received at Goddard at least twice each day from every sensor installation and is distributed to users (who operate the sensors and transmitters) by mail and teletype. The system consists of a data formatting and transmitting unit, called the Data Collection Platform (DCP), a receiver and a retransmitter aboard ERTS-1; and receiving, demodulating and decoding equipment located at the Goldstone, California and Goddard data acquisition stations. Data is transmitted from the data acquisition stations to the ERTS Control Center at Goddard, then to the NASA (ERTS) Data Processing Facility (NDPF) where it is processed and distributed to users. Experience to date indicates that the design of the ERTS-1 Data Collection System is adequate for operational use for 50% of the users and, with minor modifications, could meet the requirements of 75%. Some users will have to augment the system by other data collection techniques to meet their operational requirements.

Painter, J. E.↗
DOE OSTI2020

Performance Evaluation of Data-Enhanced Hierarchical Control for Grid Operations

This paper presents a hardware-in-the-loop (HIL) simulation to evaluate the performance of voltage regulation of Data-Enhanced Hierarchical Control (DEHC). This DEHC uses an advanced distribution management system (ADMS) for grid operations to control legacy and grid-edge devices and coordinate with distributed energy management systems (DERMS) to manage high penetrations of photovoltaics (PV) on a utility distribution system. The HIL platform provides realistic laboratory testing, including accurate modeling (legacy devices, grid-edge devices, and PV) of the real-world distribution system from a utility partner, a real controller (ADMS), software controller DERMS, hardware grid-edge devices, and standard communications protocols. The test results demonstrate functionalities of the integrated platform and the performance of voltage regulation of the coordinated control systems. Based on laboratory testing, the utility can set up the same grid-automation system to manage DERs, legacy devices, and grid-edge devices to achieve their system-level control and operation objectives (e.g., voltage regulation), thus de-risking potential issues such as instability for field deployment.

41 EE - Solar Energy Technologies Office (EE-4S)↗
NASA NTRS1987

Performance of AlGaAs, GaAs and InGaAs cells after 1 MeV electron irradiation

Electron irradiations were made on three different types of III-V cells. AlGaAs, GaAs, and InGaAs cells with bandgaps of approximately 1.72, 1.43, and 1.1 eV, respectively, were tested. All of the cells were concentrator cells and performance data from one sun to beyond 100x AMO were taken. The total 1 MeV electron fluence was 3 times 10 to the 15th power e/square cm with data taken at several intermediate fluences. Cell performance is presented as a function of electron fluence for various concentration ratios and two different temperatures (25 and 80 C). Since these three cell types are potential candidates for the individual cells in a cascade structure, it is possible to calculate the loss in performance of cascade cells under 1 MeV irradiation. Data are presented which show the calculated performance of both series-connected and separately connected cascade cells.

Curtis, Henry B.↗
NASA NTRS1973

Effect of sweep angle on the pressure distributions and effectiveness of the ogee tip in diffusing a line vortex

Low-speed wind tunnel tests were conducted to study the influence of sweep angle on the pressure distributions of an ogee-tip configuration with relation to the effectiveness of the ogee tip in diffusing a line vortex. In addition to the pressure data, performance and flow-visualization data were obtained in the wind tunnel tests to evaluate the application of the ogee tip to aircraft configurations. The effect of sweep angle on the performance characteristics of a conventional-tip model, having equivalent planform area, was also investigated for comparison with the ogee-tip configuration. Results of the investigation generally indicate that sweep angle has little effect on the characteristics of the ogee in diffusing a line vortex.

Balcerak, J. C.↗
DOE OSTI2021

A Conceptual Framework for HPC Operational Data Analytics

This paper provides a broad framework for under- standing trends in Operational Data Analytics (ODA) for High- Performance Computing (HPC) facilities. The goal of ODA is to allow for the continuous monitoring, archiving, and analysis of near real-time performance data, providing immediately actionable information for multiple operational uses. In this work, we combine two models to provide a comprehensive HPC ODA framework: one is an evolutionary model of analytics capabilities that consists of four types, which are descriptive, diagnostic, predictive and prescriptive, while the other is a four- pillar model for energy-efficient HPC operations that covers facility, system hardware, system software, and applications. This new framework is then overlaid with a description of current development and production deployments of ODA within leading- edge HPC facilities. Finally, we perform a comprehensive survey of ODA works and classify them according to our framework, in order to demonstrate its effectiveness.

Netti, Alessio↗
DOE OSTI2020

IOMiner v0.3

Modern HPC systems are collecting large amounts of I/O performance data. The massive volume and heterogeneity of this data, however, have made timely performance of in-depth integrated analysis difficult. To overcome this difficulty and to allow users to identify the root causes of poor application I/O performance, we developed IOMiner, an I/O log analytics framework.

Byna, Suren↗
DOE OSTI2021

The Cost of Decarbonization and Energy Upgrade Retrofits for US Homes

Cost is a major barrier when upgrading homes to reduce carbon emissions required to meet DOE’s climate-related goals. This report summarizes a nationwide effort to gather home energy upgrade project cost data along with household energy performance data. The goal was to develop cost benchmarks and to guide future R&D efforts aimed at cost compression and scaling of the residential upgrade market. The cost data were compiled for both total project costs and costs of individual measures. The majority of energy savings were modeled, with some models using measured site data for calibration. The database was analyzed using clustering techniques to find common energy and CO2 reduction approaches. The individual measures were combined into archetypal solutions to determine least-cost approaches to maximizing energy and carbon savings. Several financial analyses were preformed to examine other cost metrics beyond first cost. Project data was obtained for 1,739 projects, from 15 states and 12 energy programs, with a total of 10,512 individual measures. The database includes a wide-array of projects, ranging from single-measure HVAC upgrades to net-zero energy whole home remodels. Projects were predominantly single-family detached dwellings with wood frame construction. Most of the data was obtained from energy programs because they had recorded the necessary information and were willing to share with this study. This sample of convenience can provide broad guidance and national cost benchmarks, but lacks sufficient detail to draw more disaggregated conclusions, such as geographical trends. The majority of data contributions were obtained without compensation from sources where the required data was already in some sort of structured format. We compensated sources to enter data from individual projects into a structured data format for about 500 projects, with an average cost of about $40 per project. The database was highly skewed to lower cost, lower impact projects due to the nature of the sample of convenience. Less than 10% of projects had savings greater than 50%. The cost data for individual measures in the database are being used in other DOE efforts on residential energy use/decarbonization. This data collection effort should continue in order to provide the best-informed guidance for DOE and industry R&D, as well as deployment efforts (including policy and program planning).

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Ultrasonic Transducer Irradiation Test Results

Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2 . A multi-National Laboratory collaboration funded by the Nuclear Energy Enabling Technologies Advanced Sensors and Instrumentation (NEET ASI) program also provided initial support for this effort. This irradiation, which started in February 2014, is an instrumented lead test and real-time transducer performance data are collected along with temperature and neutron and gamma flux data. The irradiation is ongoing and will continue to approximately mid-2015. To date, very encouraging results have been attained as several transducers continue to operate under irradiation.

Daw, Joshua↗
NASA NTRS1971

Design and analysis of an automatic method of measuring silicon-controlled-rectifier holding current

The design of an automated SCR holding-current measurement system is described. The circuits used in the measurement system were designed to meet the major requirements of automatic data acquisition, reliability, and repeatability. Performance data are presented and compared with calibration data. The data verified the accuracy of the measurement system. Data taken over a 48-hr period showed that the measurement system operated satisfactorily and met all the design requirements.

Maslowski, E. A.↗
NASA NTRS1978

Indoor and outdoor tests of a liquid solar collector

Two reports describe thermal-performance data obtained on double-covered liquid solar collector. One report describes data obtained during outdoor testing and the other describes indoor test data obtained by using Marshall Space Flight Center solar simulator. Indoor data were taken to verify performance of solar simulator.

Losey, R.↗