Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Analysis of optically controlled microwave/millimeter wave device structures

The light-induced voltage and the change in the source-to-drain channel current under optical illumination higher than the semiconductor bandgap for GaAs MESFET, InP MESFET, Al0.3Ga0.7As/GaAs high electron mobility transistor (HEMT) and GaAs permeable base transistor (PBT) were analytically obtained. The GaAs PBT and GaAs MESFET have much higher sensitivity than InP MESFET. The Al0.3Ga0.7As/GaAs HEMT is observed to have the highest sensitivity. Variation in device parasitics due to optical illumination and its effect on the cutoff frequencies f sub T and f sub max are also investigated.

Simons, R. N.↗
NASA NTRS2015

Requirements and Design Reference Mission for the WFIRST-AFTA Coronagraph Instrument

The WFIRST-AFTA coronagraph instrument take s advantage of AFTA s 2.4 -meter aperture to provide novel exoplanet imaging science at approximately the same instrument cost as an Explorer mission. The AFTA coronagraph also matures direct imaging technologies to high TRL for an Exo-Earth Imager in the next decade. The coronagraph Design Reference Mission (DRM) optical design is based on the highly successful High Contrast Imaging Testbed (HCIT), with modifications to accommodate the AFTA telescope design, service-ability, volume constraints, and the addition of an Integral Field Spectrograph (IFS). In order to optimally satisfy the three science objectives of planet imaging, planet spectral characterization and dust debris imaging, the coronagraph is designed to operate in two different modes : Hybrid Lyot Coronagraph or Shaped Pupil Coronagraph. Active mechanisms change pupil masks, focal plane masks, yot masks, and bandpass filters to shift between modes. A single optical beam train can thus operate alternatively as two different coronagraph architecture s. Structural Thermal Optical Performance (STOP) analysis predict s the instrument contrast with the Low Order Wave Front Control loop closed. The STOP analysis was also used to verify that the optical/structural/thermal design provides the extreme stability required for planet characterization in the presence of thermal disturbances expected in a typical observing scenario. This paper describes the instrument design and the flow down from science requirements to high level engineering requirements.

contrast↗
NASA NTRS1998

MgO-Al2O3-ZrO2 Amorphous Ternary Composite: A Dense and Stable Optical Coating

The process-parameter-dependent optical and structural properties of MgO-Al2O3-ZrO2 ternary mixed-composite material were investigated. Optical properties were derived from spectrophotometric measurements. The surface morphology, grain size distributions, crystallographic phases, and process- dependent material composition of films were investigated through the use of atomic force microscopy, x-ray diffraction analysis, and energy-dispersive x-ray analysis. Energy-dispersive x-ray analysis made evident the correlation between the optical constants and the process-dependent compositions in the films. It is possible to achieve environmentally stable amorphous films with high packing density under certain optimized process conditions.

Shaoo, Naba K.↗
NASA NTRS2003

A New Fitting Procedure for the Blended He I 1083 nm Multiplet

The He I 1083 nm multiplet is a powerful tool for observing the outer solar atmosphere but is difficult to analyze because the lines are weak, highly variable, and spectrally blended, both internally and with other neighboring solar and telluric lines. After separation from nearby spectral features, two components of the He I multiplet are resolved. Fitting these lines with two unconstrained Gaussian profiles always gives a ratio of major to minor component of less than half the value which would be expected for optically thin lines. One possibility for explaining the discrepancy between the weakness of the lines and the ratio of the spectral components is to assume that the line formation regions are concentrated in laterally unresolved, optically thick structures with small filling factor. However, we present here a least-squares fitting technique using cubic splines with fixed breakpoints with the constraint that the blend is the sum of three identically shaped profiles shifted in wavelength according to the atomic structure of the blend and weighted by the corresponding statistics weights, in agreement with optically thin line formation. The basis functions for the fitting procedure have no built-in spectral symmetry or shape. The resulting underlying profiles tend to be asymmetric with excess absorption to the blue, consistent with formation by "hot" and "cool" spatial elements within the observed volume, with the hotter regions having differential motion toward the observer. The results agree well with NASA/XSO Spectromagnetograph observations in quiet sun and coronal holes. Partial funding of this research was provided through the NASA Sun-Earth Connection SR&T program.

Jones, H. P.↗
NASA NTRS2008

Optical Coating Performance and Thermal Structure Design for Heat Reflectors of JWST Electronic Control Unit

The James Webb Space Telescope (JWST) consists of an infrared-optimized Optical Telescope Element (OTE) that is cooled down to 40 degrees Kelvin. A second adjacent component to the OTE is the Integrated Science Instrument Module, or ISIM. This module includes the electronic compartment, which provides the mounting surfaces and ambient thermally controlled environment for the instrument control electronics. Dissipating the 200 watts generated from the ISIM structure away from the OTE is of paramount importance so that the spacecraft's own heat does not interfere with the infrared light detected from distant cosmic sources. This technical challenge is overcome by a thermal subsystem unit that provides passive cooling to the ISIM control electronics. The proposed design of this thermal radiator consists of a lightweight structure made out of composite materials and low-emittance metal coatings. In this paper, we will present characterizations of the coating emittance, bidirectional reflectance, and mechanical structure design that will affect the performance of this passive cooling system.

Quijada, Manuel A.↗
DOE OSTI2024

Optical and microstructural studies of erbium-doped TiO 2 thin films on silicon, SrTiO 3 , and sapphire

Rare-earth ion doped oxide thin films integrated on silicon substrates provide a route toward scalable, chip-scale platforms for quantum coherent devices. Erbium-doped TiO 2 is an attractive candidate: the Er 3+ optical transition is compatible with C-band optical fiber communications, while TiO 2 is an insulating dielectric compatible with silicon process technology. Through structural and optical studies of Er-doped TiO 2 thin films grown via molecular beam deposition on silicon, SrTiO 3 , and sapphire substrates, we have explored the impact of polycrystallinity and microstructure on the optical properties of the Er emission. Comparing polycrystalline TiO 2 (rutile)/Si with single-crystalline TiO 2 (rutile)/r-sapphire and polycrystalline TiO 2 (anatase)/Si with single-crystalline TiO 2 (anatase)/SrTiO 3 , we observe that the inhomogeneous linewidth (Γ inh ) of the most prominent peak in the Er spectrum (the Y 1 –Z 1 transition, 1520 and 1533 nm in rutile and anatase TiO 2 ) is significantly narrower in the polycrystalline case. This implies a relative insensitivity to extended structural defects and grain boundaries in such films (as opposed to, e.g., point defects). We show that the growth of an undoped, underlying TiO 2 buffer on Si can reduce Γ inh by a factor of 4–5. Expectedly, Γ inh also reduces with decreasing Er concentrations: we observe a ∼2 order of magnitude reduction from ∼1000 ppm Er to ∼10 ppm Er. Γ inh then gets limited to a residual value of ∼5 GHz that is insensitive to further reduction in the Er concentration. Based upon the above results, we argue that the optical properties in these thin films are limited by the presence of high “grown-in” point defect concentrations.

Chemical elements↗
DOE OSTI2023

Exploring fingerprints of ultrafast structural dynamics in molecular solutions with an X-ray laser

We apply ultrashort x-ray laser pulses to track optically excited structural dynamics of [Ir 2 (dimen) 4 ] 2+ molecules in solution. In our exploratory study we determine angular correlations in the scattered x-rays, which comprise a complex fingerprint of the ultrafast dynamics. Model-assisted analysis of the experimental correlation data allows us to elucidate various aspects of the photoinduced changes in the excited molecular ensembles. We unambiguously identify that in our experiment the photoinduced transition dipole moments in [Ir 2 (dimen) 4 ] 2+ molecules are oriented perpendicular to the Ir-Ir bond. The analysis also shows that the ground state conformer of [Ir 2 (dimen) 4 ] 2+ with a larger Ir–Ir distance is mostly responsible for the formation of the excited state. We also reveal that the ensemble of solute molecules can be characterized with a substantial structural heterogeneity due to solvent influence. In conclusion, the proposed x-ray correlation approach offers an alternative path for studies of ultrafast structural dynamics of molecular ensembles in the liquid and gas phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2013

Fiber Optics Deliver Real-Time Structural Monitoring

To alter the shape of aircraft wings during flight, researchers at Dryden Flight Research Center worked on a fiber optic sensor system with Austin-based 4DSP LLC. The company has since commercialized a new fiber optic system for monitoring applications in health and medicine, oil and gas, and transportation, increasing company revenues by 60 percent.

Source record↗
DOE OSTI2020

Nanometer-Thick Sr 2 IrO 4 Freestanding Films for Flexible Electronics

In this article, we report the structural and optical properties of nanoscale Sr 2 IrO 4 freestanding thin-films fabricated using a water-soluble Sr 3 Al 2 O 6 layer. The coherent lattice structure, phonon modes, two-magnon Raman scattering, and optical absorption spectra of the Sr 2 IrO 4 nanomembrane are analogous to those of the layered iridate epitaxial thin-films and single crystals. Remarkably, the formation of 3-unit-cell-thick SrIrO 3 and interfacial composite layers alleviates the antiphase boundaries at the Sr 2 IrO 4 /Sr 3 Al 2 O 6 interface, resulting in structurally-robust nanomembranes. Our experimental results show that this freestanding thin-film approach of layered oxides can provide techniques for tuning or realizing unprecedented states beyond conventional thin-film methods, suggesting a pathway in achieving flexible layered-oxide electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Interface structures of inclined ZnO thin film on (0 1 1)-MgO substrate with bulk-like optical properties

Combining different phase structure materials with unique properties to design novel devices plays a significant role in the development of modern electronics. Here, we explore the characteristics of this type of complex interface and epitaxy structures based on the coupling between hexagonal ZnO film and cubic MgO substrate. The ZnO film was prepared by the molecular beam epitaxy technique on the MgO (0 1 1) substrate. The analysis results from the in situ reflection high energy electron diffraction patterns, X-ray diffraction (XRD)-pole figures and high resolution transmission electron microscopy images demonstrate that the film exhibits two-fold symmetry domains with a growth direction deviated from c-axis at about 31º along the [0 1 0] MgO or [0 $\bar{1}$ 0] MgO azimuth. Despite the intertwined diffusion from Zn and Mg atoms in the interface, which is the possible origin of a blue shift of about 0.083 eV in the Photoluminescence (PL) spectrum, the inclined film shows a full width at half maximum value that is close to the reported value from the high quality film. Finally, this work hopefully provides useful insights to the design and exploration of the novel optoelectronic devices that involve the integration of materials with different structure and different properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Development of arsenic doped Cd(Se,Te) absorbers by MOCVD for thin film solar cells

Recent developments in CdTe solar cell technology have included the incorporation of ternary alloy Cd(Se,Te) in the devices. CdTe absorber band gap grading due to Se alloying contributes to current density enhancement and can result in device performance improvement. Here we report Cd(Se,Te) polycrystalline thin films grown by a chamberless inline atmospheric pressure metal organic chemical vapour deposition technique, with subsequent incorporation in CdTe solar cells. The compositional dependence of the crystal structure and optical properties of Cd(Se,Te) are examined. Selenium graded Cd(Se,Te)/CdTe absorber structure in devices are demonstrated using either a single CdSe layer or CdSe/Cd(Se,Te) bilayer (with or without As doping in the Cd(Se,Te) layer). Cross-sectional TEM/EDS, photoluminescence spectra and secondary ion mass spectroscopy analysis confirmed the formation of a graded Se profile toward the back contact with a diffusion length of ~1.5 um and revealed back-diffusion of Group V (As) dopants from the CdTe layer into Cd(Se,Te) grains. Due to the strong Se/Te interdiffusion, CdSe in the Se bilayer configuration was unable to form an n-type emitter layer in processed devices. In situ As doping of the Cd(Se,Te) layer benefited the device junction quality with current density reaching 28.3 mA/cm 2 . The results provide useful insights for the optimisation of Cd(Se,Te)/CdTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2022

Slow light in a 2D semiconductor plasmonic structure

Spectrally narrow optical resonances can be used to generate slow light, i.e., a large reduction in the group velocity. In a previous work, we developed hybrid 2D semiconductor plasmonic structures, which consist of propagating optical frequency surface-plasmon polaritons interacting with excitons in a semiconductor monolayer. Here, we use coupled exciton-surface plasmon polaritons (E-SPPs) in monolayer WSe 2 to demonstrate slow light with a 1300 fold decrease of the SPP group velocity. Specifically, we use a high resolution two-color laser technique where the nonlinear E-SPP response gives rise to ultra-narrow coherent population oscillation (CPO) resonances, resulting in a group velocity on order of 105 m/s. Our work paves the way toward on-chip actively switched delay lines and optical buffers that utilize 2D semiconductors as active elements.

42 ENGINEERING↗
DOE OSTI2021

Optimized structure and electronic band gap of monolayer GeSe from quantum Monte Carlo methods

Here, we have used highly accurate quantum Monte Carlo methods to determine the chemical structure and electronic band gaps of monolayer GeSe. Two-dimensional (2D) monolayer GeSe has received a great deal of attention due to its unique thermoelectric, electronic, and optoelectronic properties with a wide range of potential applications. Density functional theory (DFT) methods have usually been applied to obtain optical and structural properties of bulk and 2D GeSe. For the monolayer, DFT typically yields a larger band-gap energy than for bulk GeSe but cannot conclusively determine if the monolayer has a direct or indirect gap. Moreover, the DFT-optimized lattice parameters and atomic coordinates for monolayer GeSe depend strongly on the choice of approximation for the exchange-correlation functional, which makes the ideal structure-and its electronic properties-unclear. In order to obtain accurate lattice parameters and atomic coordinates for the monolayer, we use a surrogate Hessian-based parallel line search within diffusion Monte Carlo to fully optimize the GeSe monolayer structure. The DMC-optimized structure is different from those obtained using DFT, as are calculated band gaps. The potential energy surface has a shallow minimum at the optimal structure. This, combined with the sensitivity of the electronic structure to strain, suggests that the optical properties of monolayer GeSe are highly tunable by strain.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Spectral signatures of transverse optical modes in semiconductor nanowires

In order to build nanophotonic devices, it is important to understand and ultimately control the optical mode structure within potential components such as nanoscale waveguides. However, experimental characterization of such modes in the optical regime is difficult due to the nanoscale dimensions of such components and the perturbations that would be induced by a near-field probe. Here, we demonstrate a probe-free, far-field method to characterize the optical modes within GaN nanowires (NWs) based on a novel off-axis scanning confocal microscope system. Using this microscope, we observe spectral signatures resulting from lateral leakage of waveguide modes when they exceed their respective cutoff limits. We identify these modes within hyperspectral images using an analytical model coupled with finite element simulations. The model can also be used to predict the spectral signatures for given geometrical and dielectric parameters, which enabled us to deduce the transverse dimension of the NW from hyperspectral images with an accuracy of ∼ <#comment/> 30 nm .

Wang, Maoji↗
NASA NTRS1992

Molecular beam epitaxy engineered III-V semiconductor structures for low-power optically addressed spatial light modulators

Device approaches are investigated for optically addressed SLMs based on molecular-beam epitaxy (MBE) engineered III-V materials and structures. Strong photooptic effects can be achieved in periodically delta-doped multiple-quantum-well structures, but are still insufficient for high-contrast modulation with only single- or double-pass absorption through active layers of practical thickness. The asymmetric Fabry-Perot cavity approach is employed to permit extinction of light due to interference of light reflected from the front and back surfaces of the cavity. This approach is realized with an all-MBE-grown structure consisting of GaAs/AlAs quarter-wave stack reflector grown over the GaAs substrate as the high reflectance mirror and the GaAs surface as the low reflectance mirror. High-contrast modulation is achieved using a low-power InGaAs/GaAs quantum well laser for the control signal.

Larsson, Anders G.↗
NASA NTRS2001

Controlling Growth Orientation of Phthalocyanine Films by Electrical Fields

Organic Phthalocyanine films have many applications ranging from data storage to various non-linear optical devices whose quality is affected by the growth orientation of Phthalocyanine films. Due to the structural and electrical properties of Phthalocyanine molecules, the film growth orientation depends strongly on the substrate surface states. In this presentation, an electrical field up to 4000 V/cm is introduced during film growth. The Phthalocyanine films are synthesized on quartz substrates using thermal evaporation. An intermediate layer is deposited on some substrates for introducing the electrical field. Scanning electron microscopy, x-ray diffraction, and Fourier transform infrared spectroscopy are used for measuring surface morphology, film structure, and optical properties, respectively. The comparison of Phthalocyanine films grown with and without the electrical field reveals different morphology, film density, and growth orientation, which eventually change optical properties of these films. These results suggest that the growth method in the electrical field can be used to synthesized Phthalocyanine films with a preferred crystal orientation as well as propose an interaction mechanism between the substrate surface and the depositing molecules. The details of growth conditions and of the growth model of how the Phthalocyanine molecules grow in the electrical field will be discussed.

Zhu, S.↗
NASA NTRS2013

Three-Axis Distributed Fiber Optic Strain Measurement in 3D Woven Composite Structures

Recent advancements in composite materials technologies have broken further from traditional designs and require advanced instrumentation and analysis capabilities. Success or failure is highly dependent on design analysis and manufacturing processes. By monitoring smart structures throughout manufacturing and service life, residual and operational stresses can be assessed and structural integrity maintained. Composite smart structures can be manufactured by integrating fiber optic sensors into existing composite materials processes such as ply layup, filament winding and three-dimensional weaving. In this work optical fiber was integrated into 3D woven composite parts at a commercial woven products manufacturing facility. The fiber was then used to monitor the structures during a VARTM manufacturing process, and subsequent static and dynamic testing. Low cost telecommunications-grade optical fiber acts as the sensor using a high resolution commercial Optical Frequency Domain Reflectometer (OFDR) system providing distributed strain measurement at spatial resolutions as low as 2mm. Strain measurements using the optical fiber sensors are correlated to resistive strain gage measurements during static structural loading. Keywords: fiber optic, distributed strain sensing, Rayleigh scatter, optical frequency domain reflectometry

Castellucci, Matt↗