Results for “material performance” — Page 25

NASA NTRS2001

A New Method for Evaluating Elastomeric Materials for Use in High Pressure Oxygen

The seal configuration tester (SCT) developed at the Stennis Space Center (SSC) was designed to replicate the intended application of different seat and seal materials in a high pressure oxygen system and assess the wearibility of those materials. Statistical models were used to test the reliability of the SCT in its intended application, and the tests showed very consistent measurements over time, indicating that the device was working as intended. Other statistical designs were used to test different O-ring materials in a high-pressure oxygen system. Those tests indicated that the SCT could be used to rank the performance of O-ring materials in certain environments. The results indicated that some cheaper materials performed as well as, if not better than, other more expensive materials. Different lubrications were integrated in the testing as well and had a significant impact on the performance of the materials. Testing of seat materials is the next stage of this project. An augmentation grant (JAG) was obtained to further this experimental testing at the Stennis Space Center. This part of the project is ongoing at this time and therefore there are no significant accomplishments with respect to seat materials as of yet.

Jordan, Scott M.↗

NASA NTRS2012

Experimental Studies of Carbon Nanotube Materials for Space Radiators

Game ]changing propulsion systems are often enabled by novel designs using advanced materials. Radiator performance dictates power output for nuclear electric propulsion (NEP) systems. Carbon nanotubes (CNT) and carbon fiber materials have the potential to offer significant improvements in thermal conductivity and mass properties. A test apparatus was developed to test advanced radiator designs. This test apparatus uses a resistance heater inside a graphite tube. Metallic tubes can be slipped over the graphite tube to simulate a heat pipe. Several sub ]scale test articles were fabricated using CNT cloth and pitch ]based carbon fibers, which were bonded to a metallic tube using an active braze material. The test articles were heated up to 600 C and an infrared (IR) camera captured the results. The test apparatus and experimental results are presented here.

SanSoucie, MIchael P.↗

NASA NTRS1988

Materials processing in space: An introduction to the G-480 payload

The Space Research and Development Organization at San Jose State University designed and developed a small self-contained payload (designated G-480 by NASA) which will perform four materials science experiments in low Earth orbit aboard the Space Shuttle. These experiments are categorized under two areas of investigation: corrosion and electrodeposition. While none of these experiments have previously been performed in space, both government and industry have expressed great interest in these and related areas of materials processing and engineering. A brief history of the G-480 project development is given along with a description of each experiment, followed by a tour of the G-480 payload. Expected results are discussed along with the function, design and operation of the payload hardware and software.

Butow, Steven J.↗

NASA NTRSDate not supplied

Alteration of Optical Properties in Polymer Materials under Low Earth Orbit (LEO) Space and Simulated Exposure

This paper provides an overview of the 16th Materials International Space Station Experiment (MISSE) project, conducted by a multiorganizational team of researchers. The orbital environment during the mission, including environmental sensors data and unexpected occurrences, are discussed. The research further examines the spectral changes in selected material, Kapton TF, exposed to low Earth orbit conditions during the mission. Optical images of the material taken during the mission were analyzed using a machine learning approach. This process involved the use of a Radial Basis Function network to extract reflectance spectra from RGB/IR images. The findings were then compared with lab-based experiments of identical materials subjected to simulated space weather conditions. This comprehensive study aids in making accurate predictions about the performance of materials in space, thereby improving the reliability and safety of future space missions.

Insulators↗

NASA NTRSDate not supplied

Application Table: A Bridge Connecting the Designing “With-the-Material” and “the-Material”

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗

NASA NTRS1988

Comparison of two computer codes for crack growth analysis: NASCRAC versus NASA/FLAGRO

The service life calculations of two computer codes, NASCRAC and NASA/FLAGRO, are compared. The analysis technique is based on linear elastic fracture mechanics (LEFM), in which stresses remain below the yield strength of an elastic/plastic material. To perform service life calculations, a relationship expressing incremental crack growth, DA/DN, as a function of loading, geometry, and material properties is necessary. Load and geometry are expressed in terms of the cyclic stress intensity factor, delta K. The crack growth rate as a function of delta K is then determined by material tests, plotting DA/DN versus delta K for the given material, loading condition, and environment. Crack growth rate equations such as the Paris, Walker, and modified Forman equations are used to obtain a best fit curve to the laboratory DA/DN versus delta K data.

Stallworth, Roderick↗

NASA NTRS1998

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

The Space Shuttle vehicle (SSV) is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers (BC) are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the SSV and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the BC for two specific reasons; 1. to eliminate lead for environmental concerns, and 2. to reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hangups. This upgrade will replace the lead liner with an aluminum foam material. The aluminum foam used as a energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: A. Lead handling/ exposure, and possible contamination, along with hazardous waste disposal will be eliminated; B. Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam over lead; C. The new aluminum liner is designed to catch all shrapnel from frangible nuts thus virtually eliminating chance of foreign object debris (FOD) exiting the HDP, and causing potential damage to the vehicle; D. Potential of using the lighter aluminum liner over lead, allows for easier assembly and disassembly of blast container elements, also allowing for improvements in safety, operator handling, and efficiency of operations. Six BC firing tests will be required to determine if the new liner material will perform in a way to decrease the chance of stud hangups and enhance the ability of the BC to retain blast debris. Testing will be performed at the Kennedy Space Center (KSC) facility known as the Launch Equipment Test Facility (LETF), and will simulate the SRB hold- down post, with actual BC hardware and pyrotechnics assembled, and then test fired. Initial testing was performed in 1997 using a frangible nut in a static drop test over lead and aluminum foam sheet materials. The aluminum foam showed a dramatic improvement of energy absorption over the lead liner material. Proof-of-Principle testing at the KSC-LETF commenced in May, 1998, and is expected to be completed by June, 1998.

Ingram, T.↗

NASA NTRS1993

Novel Transition Metal Compounds with Promising Thermoelectric Properties

Progress in the search for new high temperature thermoelectric materials at the Jet Propulsion Laboratory is reviewed. Novel transition metal compounds were selected as potential new high performance thermoelectric materials and criteria of selection are presented and discussed. Samples of these new compounds were prepared at JPL by a variety of techniques. Encouraging experimental results obtained on several of these compounds are reported and show that they have the potential to be the next generation of thermoelectric materials.

Caillat, T.↗

NASA NTRS1985

Materials Test Laboratory activities at the NASA-Johnson Space Center White Sands Test Facility (WSTF)

The NASA Johnson Space Center White Sands Test Facility (WSTF) performs aerospace materials testing and evaluation. Established in 1963, the facility grew from a NASA site dedicated to the development of space engines for the Apollo project to a major test facility. In addition to propulsion tests, it tests materials and components, aerospace fluids, and metals and alloys in simulated space environments.

Stradling, J.↗

NASA NTRS2014

Remote Recession Sensing of Ablative Heat Shield Materials

Tests were performed to demonstrate the feasibility of a new method of measuring surface recession of a material sample during arc-jet testing in the NASA Ames mARC subscale developmental facility. The measurement principle was inspired through tracer elements such as Ca and Na which were seen in the spectra taken during the airborne observation campaign of the Stardust re-entry and which could be clearly observed standing out against the emission spectra emitted by postshock layer and glowing surface of the re-entry capsule. The measurement principle involves seeding of the heat shield materials at a defined depth with tracer elements which show strong and characteristic emission lines in the post shock plasma. Once the material recession reaches the seeding depth, these elements get into the hot plasma and show up in the emission spectra. The methodology was successfully demonstrated during arc-jet testing of phenolic impregnated carbonablator (PICA) material which was seeded in depth with a mixture of NaCl and MgCl in powder form. In the emission spectroscopy data, the emission lines of Mg and Na showed up about 1.5 seconds after probe insertion into the arc-jet plasma and vanished after another 2.5 seconds when recessionhad consumed the seeding material. From these data, a recession rate of about 1 mm/s is estimated.The heat flux during the test was measured to be 2575 W/sq cm on a hemispherical heat flux probewhich corresponds to a heat flux of 1036 W/sq cm on the rectangular test articles. An estimate for a lower limit of the surface temperature of 2800K during the test was obtained by fitting Planck radiation to the continuum spectra emitted by the PICA sample. Typical recession rates of PICA during testing in the large arc-jet facilities at similar test conditions are reported to be on the order of 0.05 to 0.1 cm/s which agrees well with the recession rates of 0.05-0.06 cm/s estimated from the emission spectroscopy data. Further tests under better controlled conditions are suggested to quantify this measurement method. Through a different choice of seeding materials with lower melting point, an extension of the measurement principle to monitor char depth seems feasible but was not yet demonstrated. Possible applications besides ground testing are recession and possibly char depth measurements during real re-entry. Detection through emission spectroscopy could be accomplished through ground based or airborne observation as performed during the Stardust and Hayabusa re-entries, or through on-board spectrometers. A suitable mission would be the re-entryof the OSIRIS-REX mission planned for late 2023. The measured data are presented and interpreted, the results and details of future applications are discussed.

instrumentation↗

NASA NTRS1979

Space manufacturing III; Proceedings of the Fourth Conference, Princeton University, Princeton, N.J., May 14-17, 1979

Papers are presented on the various technological, political, economic, environmental and social aspects of large manufacturing facilities in space. Specific topics include the potential global market for satellite solar power stations in 2025, the electrostatic separation of lunar soil, methods for extraterrestrial materials processing, the socio-political status of efforts toward the development of space manufacturing facilities, the financing of space industrialization, the optimization of space manufacturing systems, the design and project status of Mass Driver Two, and the use of laser-boosted lighter-than-air-vehicles as heavy-lift launch vehicles. Attention is also given to systems integration in the development of controlled ecological life support systems, the design of a space manufacturing facility to use lunar materials, high performance solar sails, the environmental effects of the satellite power system reference design, the guidance, trajectory and capture of lunar materials ejected from the moon by mass driver, the relative design merits of zero-gravity and one-gravity space environments, consciousness alteration in space and the prospecting and retrieval of asteroids.

Grey, J.↗

NASA NTRS1993

LDEF Materials Results for Spacecraft Applications

These proceedings describe the application of LDEF data to spacecraft and payload design, and emphasize where space environmental effects on materials research and development is needed as defined by LDEF data. The LDEF six years of exposure of materials has proven to be by far the most comprehensive source of information ever obtained on the long-term performance of materials in the space environment. The conference provided a forum for materials scientists and engineers to review and critically assess the LDEF results from the standpoint of their relevance, significance, and impact on spacecraft design practice. The impact of the LDEF findings on materials selection and qualification, and the needs and plans for further study, were addressed from several perspectives. Many timely and needed changes and modifications in external spacecraft materials selection have occurred as a result of LDEF investigations.

Whitaker, Ann F.↗

NASA NTRS2007

Thermal Performance Testing of Cryogenic Insulation Systems

Efficient methods for characterizing thermal performance of materials under cryogenic and vacuum conditions have been developed. These methods provide thermal conductivity data on materials under actual-use conditions and are complementary to established methods. The actual-use environment of full temperature difference in combination with vacuum-pressure is essential for understanding insulation system performance. Test articles include solids, foams, powders, layered blankets, composite panels, and other materials. Test methodology and apparatus design for several insulation test cryostats are discussed. The measurement principle is liquid nitrogen boil-off calorimetry. Heat flux capability ranges from approximately 0.5 to 500 watts per square meter; corresponding apparent thermal conductivity values range from below 0.01 up to about 60 mW/m- K. Example data for different insulation materials are also presented. Upon further standardization work, these patented insulation test cryostats can be available to industry for a wide range of practical applications.

Fesmire, James E.↗

NASA NTRS2011

Hybrid Composite Cryogenic Tank Structure

A hybrid lightweight composite tank has been created using specially designed materials and manufacturing processes. The tank is produced by using a hybrid structure consisting of at least two reinforced composite material systems. The inner composite layer comprises a distinct fiber and resin matrix suitable for cryogenic use that is a braided-sleeve (and/or a filamentwound layer) aramid fiber preform that is placed on a removable mandrel (outfitted with metallic end fittings) and is infused (vacuum-assisted resin transfer molded) with a polyurethane resin matrix with a high ductility at low temperatures. This inner layer is allowed to cure and is encapsulated with a filamentwound outer composite layer of a distinct fiber resin system. Both inner and outer layer are in intimate contact, and can also be cured at the same time. The outer layer is a material that performs well for low temperature pressure vessels, and it can rely on the inner layer to act as a liner to contain the fluids. The outer layer can be a variety of materials, but the best embodiment may be the use of a continuous tow of carbon fiber (T-1000 carbon, or others), or other high-strength fibers combined with a high ductility epoxy resin matrix, or a polyurethane matrix, which performs well at low temperatures. After curing, the mandrel can be removed from the outer layer. While the hybrid structure is not limited to two particular materials, a preferred version of the tank has been demonstrated on an actual test tank article cycled at high pressures with liquid nitrogen and liquid hydrogen, and the best version is an inner layer of PBO (poly-pphenylenebenzobisoxazole) fibers with a polyurethane matrix and an outer layer of T-1000 carbon with a high elongation epoxy matrix suitable for cryogenic temperatures. A polyurethane matrix has also been used for the outer layer. The construction method is ideal because the fiber and resin of the inner layer has a high strain to failure at cryogenic temperatures, and will not crack or produce leaks. The outer layer serves as more of a high-performance structural unit for the inner layer, and can handle external environments.

DeLay, Thomas↗

NASA NTRS1973

Complex permittivity measurements during high temperature recycling of space shuttle antenna window and dielectric heat shield materials

The research performed and the data obtained on candidate space shuttle antenna window and heat shield materials are presented. The measurement technique employs a free-space focused beam microwave bridge for obtaining RF transmission data, and a device which rotates a sample holder which is heated on one side by natural gas-air flames. The surface temperature of each sample is monitored by IR pyrometry; embedded and rear surface thermocouples are also used in obtaining temperature data. The surface of the sample undergoing test is subjected to approximately the same temperature/time profile that occurs at a proposed antenna position on the space shuttle as it re-enters. The samples are cycled through ten of these temperature profiles to determine the recycling effects. Very little change was noted in the materials due to the recycling.

Bassett, H. L.↗

NASA NTRS1985

Comparison of the contact stress and friction behavior of SiC and ZrO2 materials

Studies were performed to further elucidate the friction and contact-stress characteristics of structural ceramic materials. New data for fully stabilized and partially stabilized zirconia ceramics are compared with prior test results for sintered SiC. The comparison provides further evidence that the high temperature friction characteristics of sintered SiC are strongly influenced by the presence of a viscous surface layer. The results also show that a ceramic material with lower coefficient of friction and higher fracture toughness has increased resistance to strength-reducing surface damage due to contact stress.

Lindberg, L. J.↗

NASA NTRS2014

Lightweight Radiator for in Space Nuclear Electric Propulsion

Nuclear electric propulsion (NEP) is a promising option for high‐speed in‐space travel due to the high energy density of nuclear fission power sources and efficient electric thrusters. Advanced power conversion technologies may require high operating temperatures and would benefit from lightweight radiator materials. Radiator performance dictates power output for nuclear electric propulsion systems. Game‐changing propulsion systems are often enabled by novel designs using advanced materials. Pitch‐based carbon fiber materials have the potential to offer significant improvements in operating temperature, thermal conductivity, and mass. These properties combine to allow advances in operational efficiency and high temperature feasibility. An effort at the NASA Marshall Space Flight Center to show that woven high thermal conductivity carbon fiber mats can be used to replace standard metal and composite radiator fins to dissipate waste heat from NEP systems is ongoing. The goals of this effort are to demonstrate a proof of concept, to show that a significant improvement of specific power (power/mass) can be achieved, and to develop a thermal model with predictive capabilities making use of constrained input parameter space. A description of this effort is presented.

Craven, Paul↗

NASA NTRS2022

Application Table: A Bridge Connecting the Designing “With-The-Material” and “The-Material” Paradigms

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗