Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Time-dependent polymer rheology under constant stress and under constant shear conditions.

A kinetic rate theory previously presented for describing non-Newtonian phenomena has been further modified to predict the flow behavior of viscoelastic materials under constant stress conditions. The thixotropic shear stress or shear rate is predicted by the kinetic theory, and the experimental stress or shear rate is obtained by modifying the thixotropic value by a stress or shear rate retardation term. The retardation term stems from a Maxwellian approach for stress retardation. In order to test the validity of this approach, transient and steady-state data were obtained for two solutions of polymethylmethacrylate in diethylphthalate. Both constant stress measurements and constant shear rate data were taken over a broad range.

Lee, K. H.↗
NASA NTRS1973

High pressure oxygen utilization by NASA

Although NASA is not one of the country's major oxygen consumers, it uses oxygen under severe conditions including very high flow rates and pressure. Materials for such applications must be carefully selected for compatibility, because susceptibility to ignition increases as operating pressure is raised. Much work is needed, however to define the selection criteria. Some of the work in this area that is being performed under sponsorship of NASA's Aerospace Safety Research and Data Institute (ASRDI) is described.

Belles, F. E.↗
NASA NTRS1974

Metallurgical processing in space

Research in metallurgical processing to study the effects of reduced gravity started with Apollo 14 and advanced with Skylab. Experiments provided specimens for analysis which solidified while constrained and while freely floating, which contained a mixture of normally immiscible materials, demonstrated enhanced capillary flow, solubility and ordered growth of a directionally solidified eutectic. The smaller, equiaxed grain structure obtained in reduced gravity compared to the larger, elongated grains obtained in one gravity indicate a difference in convection due to gravity in constrained solidification. Freely floating nickel alloy specimens showing metallic gas evolution at low pressure and reduced gravity suggest reduced pressure reactions which cannot occur on earth even in high vacuum chambers due to the hydrostatic head in the molten metal. Directionally solidified eutectics showed fewer termination defects when grown in reduced gravity. These are a few of the differences observed due to reduced gravity which could have important consequences on the future of metallurgy. In this paper we attempt to correlate the results of several Skylab solidification experiments.

Mckannan, E. C.↗
NASA NTRS1976

Metal melting, joining, and alloying under weightlessness

During the Skylab mission experiments were conducted concerning the influence of weightlessness on molten metals and the solidification process. It was found that the absence of gravity-induced thermal convection and sedimentation modified the properties of the bulk melt. A metals melting experiment was conducted to study the behavior of metal melted by an electron beam and to evaluate the feasibility of joining metals in space. An exothermic brazing experiment investigated the spreading, mixing, and capillary flow of molten braze material. The containerless melting and solidification of small samples of several metals was studied in another experiment. A description is also given of a study of the directional solidification of solid solution alloys.

Snyder, R. S.↗
NASA NTRS1978

Regional energetic coupling of man and his environment: Data requirements

An energy analysis methodology was developed to serve as a rational basis for evaluating alternative regional management/use schemes. Human and natural systems are coupled and can be interpreted, using a common base of energy-flow analysis to evaluate past, present, and future states of regional integrated systems in the coastal zone and to provide the capability for rational selection of alternative patterns of resource use. Energy flows (or flows of dollars or materials converted to energy equivalents) are believed to be the basic factor in the organizations of all types of systems. An analysis example is provided of an estuarine subsystem of the Chesapeake Bay, and tabular listings of regional data needs are given. Current remote sensing capabilities were used to provide some of the necessary information.

Mihursky, J. A.↗
NASA NTRS1981

The modification stage of basin formation - Conditions of ring formation

The impact cratering process may be divided into three stages, including a short high pressure phase of initial contact between the projectile and target, a longer cratering flow phase during which material is both ejected and displaced to form the transient crater, and a still longer modification phase during which the transient crater is modified into the final observed form. The present investigation is concerned with the nature of the modification stage as constrained by the initial boundary condition which comprises the transient crater and its surroundings, and the final boundary condition which comprises the structure of observed craters and basins. A brief description is provided of an interpretation of basin ring structure based on geophysical, geological, and dimensional analysis of craters and basins on the moon, Mercury, and Mars, on structural observations of terrestrial impact and explosion craters, and on an empirical crater restoration model. A scenario of basin formation is constructed, and relations of this scenario to observed morphology are discussed.

Croft, S. K.↗
NASA NTRS1982

Compressor cascade performance deterioration caused by sand ingestion

Airfoil cascade erosion and performance deterioration was investigated in a gas particle cascade tunnel. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand. The results of the experimental measurements are presented to show the change in the blade surface erosion, pressure distribution and the total loss coefficient with erosion. The surface quality of the blades exposed to particulate flows are changing the material surfaces. With time, the surface roughness increases and leads to a decrease in engine performance. It was found that the surface roughness values increase asymptotically to a maximum value with increased erosion. The experimental results indicate that the roughness parameters correlate well against the mass of particles impacting unit area of the surface. Such a correlation is useful in aerodynamics and performance computations in turbomachinery.

Tabakoff, W.↗
NASA NTRS1983

Numerical computation of transonic flow governed by the full-potential equation

Numerical solution techniques for solving transonic flow fields governed by the full potential equation are discussed. In a general sense relaxation schemes suitable for the numerical solution of elliptic partial differential equations are presented and discussed with emphasis on transonic flow applications. The presentation can be divided into two general categories: An introductory treatment of the basic concepts associated with the numerical solution of elliptic partial differential equations and a more advanced treatment of current procedures used to solve the full potential equation for transonic flow fields. The introductory material is presented for completeness and includes a brief introduction (Chapter 1), governing equations (Chapter 2), classical relaxation schemes (Chapter 3), and early concepts regarding transonic full potential equation algorithms (Chapter 4).

Holst, T. L.↗
NASA NTRS1983

Thermomechanical loading of multilayered cylindrical geometries in thermal cycling from 300 to 1300 K

The principal of multiple material layering is well known as an effective method of reducing heat transfer; however, thermal gradients can impose significant loads and lead to delamination and subsequent component failure. An analysis is developed and experimental data are discussed for the thermomechanical effects of multilayered materials on a heat sink substrate of cylindrical geometry subject to thermal cycling. The geometry is heated in cross-flow by a high-velocity flame and cooled in crossflow by ambient-temperature air from a critical flow orifice. Each layer of material possesses a threshold beyond which small changes in temperature or mechanical loading greatly influence the life in thermal cycling of the layered materials. Comparisons are made between the thermomechanical loads predicted by various numerical codes for the linear case and by a simplified analytic model.

Hendricks, R. C.↗
NASA NTRS1983

Two hundred passage three-way valve: Fraction collector

This paper describes the design and operation of a fraction collector used to direct flow of separated biological materials from 197 capillary tubes to either a collection tray or to a waste tank. This mechanism uses a 28-volt dc gear motor driving twin cams to force 197 needles through a self-sealing silicone rubber septum, where they inject the material in 197 separate pockets in a collection tray. The position of the collector tray is sensed by two optical limit switches. The time sequences are controlled automatically by an electronics control monitoring module.

Keffer, J. L.↗
NASA NTRS1983

The Trend of Future Gas Turbine Technology

Turbomachinery system component research to advance the technology of aviation turbofan and turbojet engines is discussed. Areas of research include compressors, turbines, internal flow analysis, combustion, fuels, materials, structures, bearings, seals, lubrication, dynamics and controls, and instrumentation. A review of the research directions being taken in these areas and the steady advances being made provides a reasonable glimpse at gas turbine technology of the future.

Hartman, M. J.↗
NASA NTRS1984

Mass loss from the proto-sun - Formation and evolution of the solar nebula

It is argued that the solar nebula and hence the planetary system were formed from the mass ejected by the protosun, whose strong magnetic field controlled the azimuthal and radial flow of the ejected material. The formation and evolution of the solar nebula is discussed in the light of observations of T Tauri stars, oxygen-isotopic anomalies in meteorites, and the mass and angular momentum distribution in the present solar system.

Trivedi, B. M. P.↗
NASA NTRS1984

Helical twisting on an adiabatically expanding jet. I Propagation and temporal growth

The local linearized dispersion relation for perturbations to the surface of a constantly adiabatic jet, which is assumed to be in static pressure balance with an isothermal confining medium, is derived in an investigation of the effect of adiabatic expansion on the propagation and temporal growth of helical twisting in a supersonic jet. Cooling of the jet material along such a flow increases Mach number and relative density relative to the confining medium, as distance from the origin increases; this leads to a rather rapid decrease in the maximum rate of growth and an increase in the maximally unstable wavelength, relative to the jet's radius, as the distance along such a jet increases. Attention is given to the consequences of assuming that a change in the phase velocity of a propagating helical wave along a jet causes the wavelength of a helical wave to change.

Hardee, P. E.↗
NASA NTRS1984

The trend of future gas turbine technology

Future gas turbine technology will be based on contributions to the technology base being made today. At the NASA Lewis Research Center in Cleveland, OH, research is being conducted on turbomachinery system components and in a number of associated disciplines to advance the technology of aviation turbofan and torbojet engines. Areas of research include compressors, turbines, internal flow analysis, combustion, fuels, materials, structures, bearings, seals, lubrication, dynamics and controls, and instrumentation. A review of the research directions being taken in these areas and the steady advances being made provides a reasonable glimpse at gas turbine technology of the future.

Hartmann, M. J.↗
NASA NTRS1985

Emission in the hydrogen-Brackett lines of Epsilon Aurigae during eclipse

Results of high-resolution infrared spectroscopy of Epsilon Aur performed from 1982 and 1985 in order to investigate the effects of eclipse on spectral lines at near-infrared wavelengths are reported. The profiles of the Brackett-alpha and Brackett-gamma lines of hydrogen are reported. The B-alpha emission has an integrated flux of 9 x 10 to the -15th W/sq m, a FWHM of 60 km/s, and a radial velocity that follows the predicted velocity curve of the primary star more closely than that of the secondary. The mean B-alpha/B-gamma flux ratio was approximately unity on the three dates both lines were observed, indicating optically thick emission. It is concluded that the emission originates in a flow rather than from material in Keplerian revolution; the Brackett line emission probably has the same source as the previously observed H-alpha emission.

Backman, D. E.↗
NASA NTRS1985

ICIASF '85 - International Congress on Instrumentation in Aerospace Simulation Facilities, 11th, Stanford University, CA, August 26-28, 1985, Record

Developments related to laser Doppler velocimetry are discussed, taking into account a three-component dual beam laser-Doppler-anemometer to be operated in large wind tunnels, a new optical system for three-dimensional laser-Doppler-anemometry using an argon-ion and a dye laser, and a two-component laser Doppler velocimeter by switching fringe orientation. Other topics studied are concerned with facilities, instrumentation, control, hot wire/thin film measurements, optical diagnostic techniques, signal and data processing, facilities and adaptive wall test sections, data acquisition and processing, ballistic instrument systems, dynamic testing and material deformation measurements, optical flow measurements, test techniques, force measurement systems, and holography. Attention is given to nonlinear calibration of integral wind tunnel balances, a microcomputer system for real time digitized image compression, and two phase flow diagnostics in propulsion systems.

Source record↗
NASA NTRS1987

History and morphology of faulting in the Noctis Labyrinthus-Claritas Fossae Region of Mars

The topographically high areas cut by Noctis Labyrinthus, Noctis Fossae, and Claritas Fossae were subjected to only minor resurfacing during and following local tectonic activity. Principal resurfacing materials consist of lava flows from Syria Planum and Tharsis Montes. Thus, these areas preserve much of the fault record produced by tectonism in this region. Although recent geologic maps of the area have been produced from Viking images, the only detailed fault histories available until now were described from Mariner 9 images. Much of the faulting in the Tharsis tectonic province was centered in Syria Planum; therefore, understanding the fault history in this region is critical to understanding the stress history and tectonism of Tharsis as a whole.

Tanaka, Kenneth L.↗
NASA NTRS1986

Detection of a 'rotating' gas cloud 100 kiloparsecs in diameter surrounding 3C 275.1, a quasar at the center of a rich cluster of galaxies

The distorted radio quasar 3C 275.1 (z = 0.55) is the first QSO found to lie at the center of a rich cluster of galaxies. The quasar is surrounded by an extremely large elliptical nebulosity whose major axis exceeds 100 kpc. Spectroscopic observations of this nebulosity were obtained, with the spectrograph slit aligned along the nebulosity's major axis. The spectrum of the nebulosity in the visible is dominated by O II and O III forbidden emission lines, which yield a well-defined 'solid-body rotation curve' extending 40 kpc from the quasar nucleus, a rotation curve very different from those of normal spiral galaxies. The 3C 275.1 nebulosity is both the largest yet discovered around a quasar and the first in which organized large-scale motions (rotation?) have been identified. The nebulosity may be residue from multiple tidal interactions with cluster members, or it may be accumulated material from a 'cooling flow' of the type seen in low-redshift clusters which are X-ray sources.

Hintzen, P.↗