Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “limited memory”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Strain-concentration for fast, compact photonic modulation and non-volatile memory

A critical figure of merit (FoM) for electro-optic (EO) modulators is the transmission change per voltage, d T / d V . Conventional approaches in wave-guided modulators maximize d T / d V via a high EO coefficient or longer light-material interaction lengths but are ultimately limited by material losses and nonlinearities. Optical and RF resonances improve d T / d V at the cost of spectral non-uniformity, especially for high- Q optical cavity resonances. Here, we introduce an EO modulator based on piezo-strain-concentration of a photonic crystal cavity to address both trade-offs: (i) it eliminates the trade-off between d T / d V and waveguide loss—i.e., enhancement of the resonance tuning efficiency d v c / d V for the fixed EO coefficient, waveguide length, and cavity Q —and (ii) at high DC strains it exhibits a non-volatile (NV) cavity tuning Δ v c ,NV for passive memory and programming of multiple devices into resonance despite fabrication variations. The device is fabricated on a scalable silicon nitride-on-aluminum nitride platform. We measure d v c / d V =177±1MHz/V, corresponding to Δ v c =40±0.32GHz for a voltage spanning ±120V with an energy consumption of δ U /Δ v c =0.17nW/GHz. The modulation bandwidth is flat up to ω BW,3dB /2 π =3.2±0.07MHz for broadband DC-AC and 142±17MHz for resonant operation near a 2.8 GHz mechanical resonance. Optical extinction up to 25 dB is obtained via Fano-type interference. Strain-induced beam-buckling modes are programmable under a “read-write” protocol with a continuous, repeatable tuning range of 5±0.25GHz, allowing for storage and retrieval, which we quantify with mutual information of 2.4 bits and a maximum non-volatile excursion of 8 GHz. Using a full piezo-optical finite-element-model (FEM) we identify key design principles for optimizing strain-based modulators and chart a path towards achieving performance comparable to lithium niobate-based modulators and the study of high strain physics on-chip.

Wen, Y. Henry (ORCID:0009000685423628)↗
NASA NTRS2015

Single-Event Effect Performance of a Conductive-Bridge Memory EEPROM

We investigated the heavy ion SEE characteristics of an EEPROM based on CBRAM technology. SEFI is the dominant type of SEE for each operating mode (standby, read-only, write/read). We also observed single bit upsets in the CBRAM cell, during write/read tests. the SEULET threshold is between 10 and 20 MeV * sq cm/mg, with an upper fluence limit of 3 × 10(exp 6) cm(exp -2) at 10 MeV * sq cm/mg. In the stand by mode, the CBRAM array appears immune to bit upsets.

single event effects↗
DOE OSTI2024

Structure, bonding and electronic characteristics of amorphous Se

Ovonic threshold switching (OTS) selector can effectively improve the storage density and suppress the leakage current of advanced phase-change memory. As a prototypical OTS material, amorphous GeSe is widely investigated. But the attentions paid to amorphous Se (i.e., the functional constituent in amorphous GeSe) is very limited up to now. Here, in this work, we have explored the structure, bonding and electronic characteristics of amorphous Se using ab initio molecular dynamics simulations. The results reveal that the Se atoms in amorphous Se tend to form the 2-coordinated configurations, and they connect with each other to form the long chains. The fraction of vibrational density of state located in high frequency range is relatively large, and the formation energy of Se-Se bond is as large as 4.44 eV, hinting that the Se-Se bonds in chains possess a high stability. In addition, the mid-gap state related to the OTS behavior is also found in the amorphous Se despite of the small proportion. Our findings enrich the knowledge of the amorphous Se, which contributes to the applications of Se-based OTS selectors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2004

Miniature Linear Actuator for Small Spacecraft

A report discusses the development of a kit of mechanisms intended for use aboard future spacecraft having masses between 10 and 100 kg. The report focuses mostly on two prototypes of one of the mechanisms: a miniature linear actuator based on a shape-memory-alloy (SMA) wire. In this actuator, as in SMA-wire actuators described previously in NASA Tech Briefs, a spring biases a moving part toward one limit of its stroke and is restrained or pulled toward the other limit of the stroke by an SMA wire, which assumes a slightly lesser or greater "remembered" length, depending on whether or not an electric current is applied to the wire to heat it above a transition temperature. Topics addressed in the report include the need to develop mechanisms like these, the general approach to be taken in designing SMA actuators, tests of the two prototypes of the miniature linear actuators, and improvements in the second prototype over the first prototype resulting in reduced mass and increased stroke. The report also presents recommendations for future development, briefly discusses problems of tolerances and working with small parts, states a need for better understanding of behaviors of SMAs, and presents conclusions.

Willey, Cliff E.↗
DOE OSTI2022

Nitinol Electroslag Remelting: Initial Slag Study

Nitinol’s unique shape memory and super-elastic properties make it attractive for many applications in biomedical, automotive, aerospace, industrial refrigeration, and waste heat reclamation industries. The fatigue performance is limited however, by non-metallic inclusions (NMI) formed during the traditional VIM/VAR or multi-VAR process. ESR is a potential alternative melt process and is commonly used to refine ingot chemistry and enhance the metallurgical structure of many superalloys and specialty steels, but no study on ESR of Nitinol has been reported to date. The key to establishing a successful ESR process is selecting a compatible slag. In this study, several different slag chemistries are evaluated for their compatibility with Nitinol. One slag chemistry is chosen, along with a control, to produce four Nitinol ESR ingots. Pursuit of a novel slag chemistry for adequate Nitinol refinement is discussed.

Fezi, Kyle↗
DOE OSTI2024

Active oscillatory associative memory

Traditionally, physical models of associative memory assume conditions of equilibrium. Here, we consider a prototypical oscillator model of associative memory and study how active noise sources that drive the system out of equilibrium, as well as nonlinearities in the interactions between the oscillators, affect the associative memory properties of the system. Our simulations show that pattern retrieval under active noise is more robust to the number of learned patterns and noise intensity than under passive noise. To understand this phenomenon, we analytically derive an effective energy correction due to the temporal correlations of active noise in the limit of short correlation decay time. We find that active noise deepens the energy wells corresponding to the patterns by strengthening the oscillator couplings, where the more nonlinear interactions are preferentially enhanced. Using replica theory, we demonstrate qualitative agreement between this effective picture and the retrieval simulations. Our work suggests that the nonlinearity in the oscillator couplings can improve memory under nonequilibrium conditions.

Chemistry↗
NASA NTRS2013

Impacts of Soil-aquifer Heat and Water Fluxes on Simulated Global Climate

Climate models have traditionally only represented heat and water fluxes within relatively shallow soil layers, but there is increasing interest in the possible role of heat and water exchanges with the deeper subsurface. Here, we integrate an idealized 50m deep aquifer into the land surface module of the GISS ModelE general circulation model to test the influence of aquifer-soil moisture and heat exchanges on climate variables. We evaluate the impact on the modeled climate of aquifer-soil heat and water fluxes separately, as well as in combination. The addition of the aquifer to ModelE has limited impact on annual-mean climate, with little change in global mean land temperature, precipitation, or evaporation. The seasonal amplitude of deep soil temperature is strongly damped by the soil-aquifer heat flux. This not only improves the model representation of permafrost area but propagates to the surface, resulting in an increase in the seasonal amplitude of surface air temperature of >1K in the Arctic. The soil-aquifer water and heat fluxes both slightly decrease interannual variability in soil moisture and in landsurface temperature, and decrease the soil moisture memory of the land surface on seasonal to annual timescales. The results of this experiment suggest that deepening the modeled land surface, compared to modeling only a shallower soil column with a no-flux bottom boundary condition, has limited impact on mean climate but does affect seasonality and interannual persistence.

soil↗
DOE OSTI2022

Long-time memory effects in a localizable central spin problem

We study the properties of the Nakajima–Zwanzig memory kernel for a qubit immersed in a many-body localized (i.e. disordered and interacting) bath. We argue that the memory kernel decays as a power law in both the localized and ergodic regimes, and show how this can be leveraged to extract t → ∞ populations for the qubit from finite time (Jt ≤ 10 2 ) data in the thermalizing phase. This allows us to quantify how the long-time values of the populations approach the expected thermalized state as the bath approaches the thermodynamic limit. This approach should provide a good complement to state-of-the-art numerical methods, for which the long-time dynamics with large baths are impossible to simulate in this phase. Additionally, our numerics on finite baths reveal the possibility for unbounded exponential growth in the memory kernel, a phenomenon rooted in the appearance of exceptional points in the projected Liouvillian governing the reduced dynamics. In small systems amenable to exact numerics, we find that these pathologies may have some correlation with delocalization.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Effect of Al substitution on the magnetocaloric properties of Ni-Co-Mn-Sn multifunctional alloys

Ni-Mn-based metamagnetic shape memory alloys have been extensively studied due to their multifunctional properties including magnetocaloric effect (MCE), magnetoresistance effect, and magnetic-field-induced strain. However, the large intrinsic thermal hysteresis of these alloys sets a limit on further development for practical applications. Here, with a few atomic percent Al substitution, we greatly reduced the thermal hysteresis and transformation temperature interval while maintaining the large magnetization difference (ΔM) between austenite and martensite. The simultaneous achievement of a large ΔM and low thermal hysteresis leads to a remarkable enhancement in MCE upon Al substitution, and a maximum magnetic entropy change of 31.6 J/kg K is achieved under a field of 5 T in Ni 39 Co 11 Mn 40 Sn 8 Al 2 . Furthermore, our in situ high-energy X-ray diffraction experiments show that the Ni 39 Co 11 Mn 40 Sn 8 Al 2 has good geometric compatibility between austenite and martensite, which accounts for the reduced thermal hysteresis in this alloy. This study is instructive for the development of high-performance magnetocaloric materials in the metamagnetic shape memory alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Shock-induced transformation of nitinol shape memory alloy: Effect of stress state on transformation

Due to its numerous practical applications and intriguing phase transformation behavior, shape memory alloys (SMAs) have garnered significant research and development interests. In the past, most studies on the mechanical behavior of SMAs have been conducted under uniaxial stress loadings. Limited research on SMAs under shock loading has not provided conclusive results regarding their transformation behavior and transformation stress under such loading. Additionally, there is a lack of comprehensive understanding regarding the effects of different stress states on transformation behavior. The main objectives of this study are to address these issues. To achieve these objectives, a series of shock wave experiments were designed and conducted. Additionally, quasi-static and dynamic uniaxial stress experiments were carried out to establish a baseline for comparison. The results revealed that the transformation stress under dynamic uniaxial strain shock loading was approximately 1.92 GPa in contrast to 0.5 GPa (quasi-static) to 0.8 GPa (dynamic) observed in uniaxial stress loading. The transformation behavior exhibited noticeable rate sensitivity for both types of loading. There appeared to be a critical strain rate above which the austenite phase was driven to a metastable state. This estimated critical axial strain rate along the loading direction was approximately 2 × 10 3 /s–4 × 10 3 /s for uniaxial stress loading and approximately 2 × 10 6 /s for uniaxial strain loading. The apparent high transformation stress for uniaxial strain loading can likely be attributed to a combination of high-pressure confinement and high strain rate. Furthermore, determining their relative contributions remains an open issue.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Converged ab initio calculations of heavy nuclei

We propose a novel storage scheme for three-nucleon (3N) interaction matrix elements relevant for the normal-ordered two-body approximation used extensively in ab initio calculations of atomic nuclei. This scheme reduces the required memory by approximately two orders of magnitude, which allows the generation of 3N interaction matrix elements with the standard truncation of E 3max =28, well beyond the previous limit of 18. We demonstrate that this is sufficient to obtain the ground-state energy of 132 Sn converged to within a few MeV with respect to the E 3max truncation. In addition, we study the asymptotic convergence behavior and perform extrapolations to the un-truncated limit. Finally, we investigate the impact of truncations made when evolving free-space 3N interactions with the similarity renormalization group. We find that the contribution of blocks with angular momentum J rel > 9/2 to the ground-state energy is dominated by a basis-truncation artifact, which vanishes in the large-space limit, so these computationally expensive components can be neglected. For the two sets of nuclear interactions employed in this work, the resulting binding energy of 132 Sn agrees with the experimental value within theoretical uncertainties. This work enables converged ab initio calculations of heavy nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Securing Smart Manufacturing: Detection of Cyber-Physical Attacks in CNC-Based Systems

As Industry 4.0 advances, the integration of computer numerical control (CNC) machines and advanced manufacturing technologies is transforming production into smart manufacturing systems that blend physical and digital processes as cyber-physical systems. However, this increased cyber-physical connectivity exposes manufacturing systems to cyber threats that can cause severe operational and financial disruptions. This paper presents a comparative study on cyber attacks and anomaly detection techniques in manufacturing, focusing on network traffic from CNC machines. The data extracted from network packets includes machine commands and control signals exchanged between the machine's interface and control system, crucial for maintaining operational integrity. We explore two types of cyber attacks, design modification and command injection, which pose substantial risks to CNC machine productivity and system integrity. Our investigation involves experiments on a real CNC system, highlighting the urgent need for effective detection mechanisms. To address these threats, we evaluate three anomaly detection methods: dynamic time warping (DTW), rolling average, and a deep learning, long short-term memory (LSTM) time-series-based autoencoder. Each is assessed for its effectiveness in identifying anomalous behaviors caused by the attacks. Our findings demonstrate the unique strengths and limitations of each detection technique, providing a deeper understanding of their applicability in realworld manufacturing environments. The comparative analysis indicates that while certain methods are highly effective against specific attack types, others offer broader applicability across different attacks. This study contributes to the accurate detection of anomalies in CNC machining processes, thereby enhancing the reliability and security of smart manufacturing systems against diverse cyber threats.

Williams, Bethanie [Tennessee Technological Univer↗
DOE OSTI2023

Superconducting Hyperdimensional Associative Memory Circuit for Scalable Machine Learning

Here we propose a generalized architecture for the first rapid-single-flux-quantum (RSFQ) associative memory circuit. The circuit employs hyperdimensional computing (HDC), a machine learning (ML) paradigm utilizing vectors with dimensionality in the thousands to represent information. HDC designs have small memory footprints, simple computations, and simple training algorithms compared to superconducting neural network accelerators (SNNAs), making them a better option for scalable SFQ machine learning (ML) solutions. The proposed superconducting HDC (SHDC) circuit uses entirely on-chip RSFQ memory which is tightly integrated with logic, operates at 33.3 GHz, is applicable to general ML tasks, and is manufacturable at practically useful scales given current SFQ fabrication limits. Tailored to a language recognition task, SHDC consists of ~ 2-20 M Josephson junctions (JJs) and consumes up to three times less power than an analogous CMOS HDC circuit while achieving 78-84% higher throughput. SHDC is capable of outperforming the state of the art RSFQ SNNA, SuperNPU, by 48-99% for all benchmark NN architectures tested while occupying up to 90% less area and consuming up to nine times less power. To the best of the authors' knowledge, SHDC is currently the only superconducting ML approach feasible at practically useful scales for real-world ML tasks and capable of online learning.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Adapting CLUTCH methodology to multigroup TSUNAMI-3D for eigenvalue sensitivity calculations

The sensitivity of the eigenvalue to uncertainties in nuclear data and its evaluation are important for nuclear criticality safety. TSUNAMI-3D sequences within the SCALE code system offer several options to the user community for calculating eigenvalue sensitivity coefficients with multigroup (MG) and continuous energy (CE) 3D transport capabilities. TSUNAMI-3D sequences implement the adjoint-based perturbation theory with MG KENO code, the Contributon Linked eigenvalue sensitivity/Uncertainty estimation via Track length importance CHaracterization (CLUTCH) method with CE KENO code, and the Iterated Fission Probability (IFP) method with CE KENO and Shift codes. Each method has benefits and limitations depending on the problem that is run. The work presented here aims to adapt the CLUTCH method, which enables the Contributon method's mesh-free, memory-efficient approach for calculating adjoint-weighted tallies for sensitivity calculations, to the MG TSUNAMI-3D sequence. This application would eliminate the explicit adjoint KENO calculation, as well as the memory-consuming mesh flux moment tallies required by the conventional MG TSUNAMI-3D. Smaller memory footprints in the CLUTCH methodology and relatively shorter runtimes in MG KENO transport can make MG TSUNAMI-3D a viable method for some complex problems. Moreover, this adaptation allows MG sensitivity calculations with Shift, ORNL's next-generation high-performance Monte Carlo transport code, which currently does not offer any sensitivity capabilities with MG particle transport simulations. Initial implementation of the new MG TSUNAMI-3D sequence and its preliminary results with a selected critical benchmark experiment in the Verified, Archived Library of Inputs and Data (VALID) are presented in this study.

KENO↗
NASA NTRS1944

Use of Internal Coolant as a Means of Permitting Increase in Engine Take-Off Power

Engine tests, together with estimates made at Langley Memorial Aeronautical Laboratory, indicate that a 25-percent increase in take-off power can be obtained with present-day aircraft engines without increasing either the knock limit of the fuel or the external cooling requirements of the engine. This increase in power with present fuels and present external cooling is made possible through the use of an internal coolant inducted through the inlet manifold. Estimates on aircraft indicate that this 25-percent increase in power will permit an approximate usable increase of 8.5 percent in the take-off load of existing military airplanes. This increase in load is equivalent to an increase in the weight of gasoline normally carried of between 30 and 65 percent.

FUELS, ANTIKNOCK↗
NASA NTRS1998

On the Information Content of Program Traces

Program traces are used for analysis of program performance, memory utilization, and communications as well as for program debugging. The trace contains records of execution events generated by monitoring units inserted into the program. The trace size limits the resolution of execution events and restricts the user's ability to analyze the program execution. We present a study of the information content of program traces and develop a coding scheme which reduces the trace size to the limit given by the trace entropy. We apply the coding to the traces of AIMS instrumented programs executed on the IBM SPA and the SCSI Power Challenge and compare it with other coding methods. Our technique shows size of the trace can be reduced by more than a factor of 5.

Frumkin, Michael↗
DOE OSTI2021

A deep learning hybrid predictive modeling (HPM) approach for estimating evapotranspiration and ecosystem respiration

Climate change is reshaping vulnerable ecosystems, leading to uncertain effects on ecosystem dynamics, including evapotranspiration (ET) and ecosystem respiration (R eco ). However, accurate estimation of ET and R eco still remains challenging at sparsely monitored watersheds, where data and field instrumentation are limited. In this study, we developed a hybrid predictive modeling approach (HPM) that integrates eddy covariance measurements, physically based model simulation results, meteorological forcings, and remote-sensing datasets to estimate ET and R eco in high space–time resolution. HPM relies on a deep learning algorithm and long short-term memory (LSTM) and requires only air temperature, precipitation, radiation, normalized difference vegetation index (NDVI), and soil temperature (when available) as input variables. We tested and validated HPM estimation results in different climate regions and developed four use cases to demonstrate the applicability and variability of HPM at various FLUXNET sites and Rocky Mountain SNOTEL sites in Western North America. To test the limitations and performance of the HPM approach in mountainous watersheds, an expanded use case focused on the East River Watershed, Colorado, USA. The results indicate HPM is capable of identifying complicated interactions among meteorological forcings, ET, and R eco variables, as well as providing reliable estimation of ET and R eco across relevant spatiotemporal scales, even in challenging mountainous systems. The study documents that HPM increases our capability to estimate ET and R eco and enhances process understanding at sparsely monitored watersheds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Ionic complexation of endblock-sulfonated thermoplastic elastomers and their physical gels for improved thermomechanical performance

Thermoplastic elastomers (TPEs) composed of nonpolar triblock copolymers constitute a broadly important class of (re)processable network-forming macromolecules employed in ubiquitous commercial applications. Physical gelation of these materials in the presence of a low-volatility oil that is midblock-selective yields tunably soft TPE gels (TPEGs) that are suitable for emergent technologies ranging from electroactive, phase-change and shape-memory responsive media to patternable soft substrates for flexible electronics and microfluidics. Many of the high-volume TPEs used for these purposes possess styrenic endblocks that are inherently limited by a relatively low glass transition temperature. To mitigate this shortcoming, we sulfonate and subsequently complex (and physically crosslink) the endblocks with trivalent Al3+ ions. Doing so reduces the effective hydrophilicity of the sulfonated endblocks, as evidenced by water uptake measurements, while concurrently enhancing the thermomechanical stability of the corresponding TPEGs. Chemical modification results, as well as morphological and property development, are investigated as functions of the degree of sulfonation, complexation and TPEG composition. (C) 2020 Published by Elsevier Inc.

36 MATERIALS SCIENCE↗