SEARCH · Engineering Papers

Results for “large rotors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Navier-Stokes Calculations for a Highly-Twisted Rotor Near Stall

The viscous flow field near the surface of a hovering rotor blade was studied for blade twist distributions typical of a till rotor blade and a conventional helicopter rotor blade. Three blade geometries were studied, including a tilt rotor blade twist distribution (baseline), conventional helicopter rotor blade twist distribution, and the baseline twist distribution with 2 deg of precone. The results give insight into the delayed stall phenomenon often observed for highly twisted rotors. Calculations were performed for a high thrust condition near stall using the thin-layer Navier-Stokes CFD code TURNS. Effects of built-in twist on section force coefficients, skin friction, velocities, surface pressures, and boundary layer shape factor are discussed. Although the rotor thrust coefficient was nominally the same for the cases using the two twist distributions, large differences were found in the section in-plane and normal force coefficients. These preliminary results imply that the blade outboard region, rather than the inboard region, provides the majority of the performance advantage of the baseline case over the low twist case. Skin friction, velocities near the blade, and surface pressures for the two twist distributions reveal significant differences in the blade outboard region.

Yamauchi, Gloria K.↗

NASA NTRS2002

Observer-Based Magnetic Bearing Controller Developed for Aerospace Flywheels

A prototype of a versatile, observer-based magnetic bearing controller for aerospace flywheels was successfully developed and demonstrated on a magnetic bearing test rig (see the photograph) and an actual flywheel module. The objective of this development included a fast, yet low risk, control development process, and a robust, high-performance controller for a large variety of flywheels. This required a good system model, an efficient development procedure, and a model-based controller that addressed the key problems associated with flywheel and bearing imbalance, sensor error, and vibration. The model used in this control development and tuning procedure included the flexible rotor dynamics and motor-induced vibrations. Such a model was essential for low-risk scheduling of speed-dependent control parameters and for reliable evaluation of novel control strategies. The successfully tested control prototype utilized an extended Kalman filter to estimate the true rotor principal-axis motion from the raw sensor position feedback. For control refinement, the extended Kalman filter also estimated and eliminated the combined effects of mass-imbalance and sensor runouts from the input data. A key advantage of the design based on the extended Kalman filter is its ability to accurately estimate both the rotor's principal-axis position and gyroscopic rates with the least amount of phase lag. This is important for control parameter scheduling to dampen the gyroscopic motions. Because of large uncertainties in the magnetic bearing and imbalance characteristics, this state-estimation scheme alone is insufficient for containing the rotor motion within the desired 1-mil excursion radius. A nonlinear gain adjustment based on an estimation of the principal-axis orbit size was needed to provide a coarse (nonoptimal), but robust, control of the orbit growth. Control current minimization was achieved with a (steepest gradient) search of synchronous errors in the principal-axis position input data. Actual flywheel tests of this observer-based controller (developed entirely in-house) at the NASA Glenn Research Center showed that the model correctly predicted the rotor orbit growth as a function of rotational speed, and it demonstrated the capability of gain adjustments to arrest this growth. Data from these tests on an actual flywheel module spun to 26,000 rpm proved that the controller was able to contain the shaft motion to within much less than 0.5 mils of radial excursion with axis currents less than 300 mA in root-mean-square estimate. The test speed range was limited because of thermal expansion concerns for this particular flywheel unit, not because of any deficiency in the controller. Simulations for this unit indicated that the controller should be robust up to its top operating speed of 60,000 rpm. Aside from these important achievements, and most significantly, it took less than 1 week to adapt this controller from the simple test rig to the actual flywheel and to demonstrate full five-axis levitation and control. This demonstration showed that both the controller and the model-based development and tuning framework are easily adaptable to a wide range of rotors and bearing configurations and, hence, are capable of reducing design risks and costs for many future flywheel technology developments.

Le, Dzu K.↗

NASA NTRSDate not supplied

Smart Twisting Active Rotor (STAR) – Pre-Test Predictions

A Mach-scaled model rotor with active twist capability is in preparation for a wind tunnel test in the large lowspeed facility (LLF) of the German-Dutch wind tunnel (DNW) with international participation by DLR, US Army, NASA, ONERA, KARI, Konkuk University, JAXA, Glasgow University and DNW. To get the maximum benefit from the test and most valuable data within the available test time, the tentative test matrix was covered by predictions of the partners, active twist benefits were evaluated, and support was provided to the test team to focus on the key operational conditions.

acoustics↗

NASA NTRS2015

Unsteady Loss in the Stator Due to the Incoming Rotor Wake in a Highly-Loaded Transonic Compressor

The present paper reports an investigation of unsteady loss generation in the stator due to the incoming rotor wake in an advanced GE transonic compressor design with a high-fidelity numerical method. This advanced compressor with high reaction and high stage loading has been investigated both experimentally and analytically in the past. The measured efficiency in this advanced compressor is significantly lower than the design intention/goal. The general understanding is that the current generation of compressor design/analysis tools miss some important flow physics in this modern compressor design. To pinpoint the source of the efficiency miss, an advanced test with a detailed flow traverse was performed for the front one and a half stage at the NASA Glenn Research Center. Detailed data-match analysis by GE identified an unexpected high loss generation in the pressure side of the stator passage. Higher total temperature and lower total pressure are measured near the pressure side of the stator. Various analyses based on the RANS and URANS of the compressor stage do not calculate the measured higher total temperature and lower total pressure on the pressure side of the stator. In the present paper, a Large Eddy Simulation (LES) is applied to find the fundamental mechanism of this unsteady loss generation in the stator due to the incoming rotor wake. The results from the LES were first compared with the NASA test results and the GE interpretation of the test data. LES calculates lower total pressure and higher total temperature on the pressure side of the stator, as the measured data showed, resulting in large loss generation on the pressure side of the stator. Detailed examination of the unsteady flow field from LES shows that the rotor wake, which has higher total temperature and higher total pressure relative to the free stream, interacts quite differently with the pressure side of the blade compared to the suction side of the blade. The higher temperature in the wake remains high as the wake passes through the pressure side of the blade. On the other hand, the total temperature diffuses as it passes through near the suction surface. For the presently investigated compressor, the classical intra-stator wake transport to the pressure side of the blade by the slip velocity in the wake seems to be minor. The main causes of this phenomenon are three-dimensional unsteady vortex interactions near the blade surface. The stabilizing effect of the concave curvature on the suction side keeps the rotor wake thin. On the other hand, the destabilizing effect of the convex curvature of the pressure side makes the rotor wake thicker, which results in a higher total temperature measurement at the stator exit. Additionally, wake stretching through the stator seems to contribute to the redistribution of the total temperature and the loss generation.

Efficiency↗

NASA NTRS1938

A study of the torque equilibrium of an autogiro rotor

Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high tip-speed ratios, by means of charts based on graphical integrations, errors inherent in the assumptions associated with the analytical method are largely eliminated. The suggested method of estimating the inflow velocity presupposes a knowledge of the decelerating torque acting on the rotor; all available full-scale experimental information on this subject is included.

Bailey, F J , Jr↗

NASA NTRS1992

Radiated noise of ducted fans

The differences in the radiated acoustic fields of ducted and unducted propellers of the same thrust operating under similar conditions are investigated. An FEM model is created for the generation, propagation, and radiation of steady, rotor alone noise and exit guide vane interaction noise of a ducted fan. For a specified number of blades, angular mode harmonic, and rotor angular velocity, the acoustic field is described in a cylindrical coordinate system reduced to only the axial and radial directions. It is found that, contrary to the usual understanding of the Tyler and Sofrin (1962) result, supersonic tip speed rotor noise can be cut off if the tip Mach number is only slightly in excess of unity and if the number of blades is relatively small. If there are many blades, the fundamental angular mode number is large, and the Tyler and Sofrin result for thin annuli becomes more relevant. Shrouding of subsonic tip speed propellers is a very effective means of controlling rotor alone noise.

Eversman, Walter↗

NASA NTRSDate not supplied

Simulation of the Rotorwash Induced by a Quadrotor Urban Air Taxi in Ground Effect

A rotorcraft hovering near the ground causes downwash and outwash. The impact of these induced velocities on urban air mobility operations has not been extensively quantified. This paper explores the opportunity of using CFD to perform dedicated studies on the aerodynamics of rotorcraft in ground effect (IGE). For this purpose, we compare load and flow predictions obtained with the high-fidelity CFD solver OVERFLOW and with a medium-fidelity vortex particle-mesh (VPM) method, for a single rotor IGE. We show that the computational cost of high-fidelity simulation makes it impractical to sweep through a large number of configurations or operating conditions. However, a small set of cases can be used to verify a medium-fidelity tool. The latter provides a better trade-off between “accuracy” and computational intensity, which enables numerous, longer simulations at a more affordable cost. As an example, the outwash flow is computed for two different designs of a quadrotor air taxi in hover and reveals the existence of increased velocities between the rotors. This work illustrates how CFD can help identify dangerous areas for passengers and ground personnel when they approach the vehicle.

HECC↗

NASA NTRS1998

Application of Pressure-Sensitive Paint to Rotorcraft

In this presentation, a plan to develop methods for applying pressure-sensitive paint to rotorcraft will be described. These methods are needed because flows over rotor blades are typically very complex and poorly understood and because conventional methods for measuring unsteady pressures on rotor blades (using unsteady pressure transducers provide grossly inadequate spatial resolution. Since PSP is a surface, rather than a point, measurement technique, it has the potential to significantly increase the spatial resolution )f pressure measurements on rotor blades. PSP techniques currently in use at Ames were developed for measuring steady pressures on rigid, complex airplane configurations in large, production wind tunnels. Applying PSP to rotorcraft requires a significant departure from these techniques. First and most importantly new, fast-responding and self-referencing pressure paints are required. The paints must be fast (98% response in 1-5 msec) to resolve flow unsteadiness; they must be self-referencing (or "binary") to account for changes in incident light intensity due to deflection of flexible rotors. Self-referencing paints have been used at Ames for some time; however, these paints have response times that are far too long for unsteady applications. Flash illumination is required to resolve flow unsteadiness and to minimize image blurring due to relative motion between the model and the camera. Current practice at Ames is to use continuous illumination Finally, "in situ" paint calibration versus measurements by pressure transducers, which is current Ames practice, is not practical because of the difficulty and expense of installing transducers in rotor blades. Instead, the paint must be calibrated "a priori" in a calibration chamber. A sequence of five experiments that systematically isolates and addresses the problems involved in making PSP measurements on rotor blades has been planned. These are: (1) measurements on a rigid rotor in hover; (2) measurements on a flexible rotor in hover; measurements of paint response time in a calibration apparatus; (4) measurements on a rigid, two-dimensional oscillating airfoil; and (5) measurements on a flexible rotor in forward flight. Experiments were recently conducted at Ames where PSP measurements were made on a rigid oscillating airfoil (experiment type 4) and on a flexible rotor in hover (experiment type 2). Preliminary results from these experiments will be discussed.

Schairer, Edward T.↗

NASA NTRS1966

Handling qualities and structural characteristics of the hingeless-rotor helicopter

Several advantages and potential problem areas associated with the hingeless-rotor helicopter are discussed. The extent to which two of the advantages - increased control and damping moments - can be obtained with the hingeless-rotor helicopter is established. The upper limit on the available control and damping moments is associated with the excessive gyroscopic coupling that is obtained with heavy rotor blades. The potential problem areas identified include a structural mode of oscillation very similar to that of a pendulum, which causes undesirably large roll accelerations under certain flight conditions, and large cyclic chordwise bending moments that occur during severe maneuvers (the primary structural problem of concern). Solutions are proposed which should eliminate future concern with these problems.

HELICOPTER↗

DOE OSTI2021

On steady alternate bars forced by a localized asymmetric drag distribution in erodible channels

Studying the effect of different in-stream fluvial turbines siting on river morphodynamics allowed us to witness the onset of a time-averaged, large-scale, alternate distortion of bed elevations, which could not be exclusively related to the turbine rotor blockage. The longitudinal profiles of this two-dimensional bathymetric perturbation resemble those of steady fluvial bars. In this contribution we generalize the problem addressing a spatially impulsive, asymmetric distribution of drag force in the channel cross-section. Furthermore, this is experimentally investigated through the deployment of differently sized grids perpendicular to the flow, and analytically explored as a finite perturbation of an open channel flow over an erodible sediment layer, as described by a coupled flow–sediment shallow water equation. The steady solutions of this fluvial morphodynamic problem, physically represented by alternate bars scaling with the channel width, highlight the importance of the resonant conditions in defining the spatial extent of the bed deformation. The equations further suggest that in very shallow flows any asymmetric obstruction may lead to an upstream propagation of the steady bars, consistent with previous studies on the effects of channel curvature. In broad terms, this study provides the preliminary framework to control the onset of river meandering through imposed finite perturbations of the cross-section. In a more applied sense, it provides a tool to predict non-local scour–deposition patterns associated with the deployment of energy converters or other flow obstructions.

42 ENGINEERING↗

NASA NTRS1982

Performance and load data from Mod-0A and Mod-1 wind turbine generators

Experimental data, together with supporting analysis, are presented on the power conversion performance and blade loading of large, horizontal-axis wind turbines tested at electric utility sites in the U.S. Four turbine rotor configurations, from 28 to 61 meters in diameter, and data from five test sites are included. Performance data are presented in the form of graphs of power and system efficiency versus free-stream wind speed. Deviations from theoretical performance are analyzed statistically. Power conversion efficiency averaged 0.34 for all tests combined, compared with 0.31 predicted. Round blade tips appeared to improve performance significantly. Cyclic blade loads were normalized to develop load factors which can be used in the design of rotors with rigid hubs.

Spera, D. A.↗

NASA NTRS1984

The laboratory millimeter and submillimeter spectrum of HCO

The rotational absorption frequencies of 68 new lines from the HCO radical in its ground electronic state have been measured in the millimeter and submillimeter spectral region. The large zero-field data set acquired has allowed the complex spectrum of this light asymmetric rotor with unpaired electronic spin and magnetic hyperfine interactions to be completely analyzed to within experimental accuracy for the first time. The wide range of states observed provides a highly accurate map of the rotational frequencies of the formyl radical, which should enable the abundance and excitation of interstellar HCO to be examined in detail.

Blake, G. A.↗

NASA NTRS2007

Rapid Calculations of Three-Dimensional Inlet/Fan Interaction

Two computational fluid dynamics codes have been merged to permit rapid calculations of inlet/fan interaction. Inlets are modeled using the WIND-US Navier-Stokes code. Fans are modeled using a new three-dimensional Euler code called CSTALL that solves the flow through the entire compression system but models blade rows using body forces for turning and loss. The body force model is described and it is shown how unknown terms in the model can be estimated from other Navier-Stokes solutions of the blade rows run separately. The inlet and fan calculations are run simultaneously and are coupled at an interface plane using a third code called SYNCEX that is described briefly. Results are shown for an axisymmetric nacelle at high angle of attack modeled both as an isolated inlet and coupled to a single stage fan. The isolated inlet calculations are unrealistic after the flow separates but the coupled codes can model large regions of separated flow extending from the lower lip of the nacelle into the fan rotor.

Chima, Rodrick V.↗

NASA NTRS1947

Vibration Survey of Blades in 19XB Axial-Flow Compressor: Dynamic Investigation - 2

Strain-gage measurements were taken under operating conditions from blades of various stages of the 19XB axial-flow compressor in an effort to determine the reason for failures in the seventh and tenth stages. First bending-mode vibrations were detected in the first five stages of the compressor caused by each integral multiple of rotor speed from three through ten. Lead-wire failures in the last five stages resulted in incomplete data. The dynamic-vibration frequencies at various rotor speeds were compared with statically measured frequencies analytically corrected for the influence of centrifugal force. Large increases in vibration ani~litude with increased pressure ratio were observed. During surging operation, blade vibrations were not present. The effects of pressure ratio and surge indicate the existence of aerodynamic excitation as the cause of the blade vibrations.

Meyer, Andre J., Jr.↗

NASA NTRSDate not supplied

Comparing Methods to Extract Sectional Angle of Attack From Blade-Resolved Rotor Simulations

The angle of attack is widely used to describe the aerodynamics of rotor blades. Models based on lifting lines, actuator lines, and actuator disks use it as a primary variable, assuming the aerodynamics can be represented by the flow around a collection of equivalent 2D airfoils. This paper evaluates the accuracy of existing methods that extract the angle of attack from blade-resolved CFD simulations, towards enabling a direct comparison of angle of attack between blade-resolved and blade-modeled simulations. Results are compared for a 2D airfoil for which the angle of attack is known by definition. The hovering rotor case is also considered, where we look at two different rotor blades. We discuss the factors that impact the accuracy of the 2D predictions. For the 3D rotors, we show that three-dimensional effects in the root and tip regions lead to large discrepancies between methods. This suggests that the very definition of angle of attack is unable to accurately represent the flow in these regions. Finally, based on guidelines that we establish, we propose an alternate method that uses local velocities sampled on a contour located 0.25 chord, or less, away from the airfoil surface and generally yields improved accuracy compared to most existing techniques.

ARMD↗

DOE OSTI2021

Big Adaptive Rotor Phase I (Final Report)

The Big Adaptive Rotor (BAR) project was initiate by DOE in 2018 with the goal of identifying novel technologies that can enable large (>100m) blades for low specific power (SP) turbines. Five distinct tasks were completed to achieve this goal: 1. Assess trends, impacts, and value of low-SP turbines, 2. Wind turbine blade cost reduction roadmap study, 3. Research and Development (R&D) opportunity screening, 4. Detailed design and analysis, and 5. Low-cost carbon fiber. These tasks were completed by the national lab team consisting of Sandia National Laboratories (SNL), the National Renewable Energy Laboratory (NREL), and Lawrence Berkeley National Laboratory (LBNL). The objective of Task 1 was to assess the historical trends of low-SP of onshore deployments, and to assess the impact and value of low-SP turbines. Analysis under this task showed that there is significant value for low-SP turbines, especially in markets where there is a higher saturation of wind energy on the grid. This has to do with the fact that low-SP turbines have increased capacity factors, and can contribute more reliable energy to the grid, even in lower wind conditions. This bodes well as higher renewable scenarios are likely in the coming years. Task 2 was a detailed analysis on the logistical challenges of deploying very large (>100m) onshore blade. This work was completed by experts at DNV-GL. The report looked at various ways to get around the current transportation constraints which are estimated to be around 75m in length. The report concluded that there are viable solutions to this issue including: segmented blades (which the industry is already pursuing), lighter than air (LTA) transportation, on-site manufacturing, and controlled bending of blades on rail. The final option was recommended for further analysis and study by DOE and the national labs because keeping a single piece blade reduces manufacturing and operations and maintenance (O&M) costs. Task 3 focused on identifying novel concepts that are capable of enabling a cost effective 5MW 206m rotor for onshore deployment. The findings from the first two tasks were considered in the analysis, in that the concepts identified must be able to overcome the transportation logistics challenges. Around 20 concepts were identified and evaluated by experts within the industry. Additionally, science and engineering challenges were identified for each concept. Based on these evaluations six concepts were deemed the most impactful and were selected for further analysis in Task 4. The concepts were: highly flexible rail transportable blades, downwind rotors, distributed aerodynamic control (DAC) devices, inflatable blade, bi-wing blade, and 4/5 bladed rotors. Task 4 conducted detailed design, optimization, and analysis on the selected BAR concepts. A modeling gaps analysis was conducted, and modeling improvements were implemented that allowed for the study and design of the novel concepts. The BAR team established a set of baseline designs by which to compare the selected designs through a technoeconomic analysis. It was found that the highly flexible rail transportable blade, the downwind rotor, and the DAC devices have the most promise to deliver the BAR targets. A Phase II for BAR has been proposed to further mature these concepts and address the open science and engineering challenges identified in Task 3. Task 5 conducted research on optimized carbon fiber materials that were used throughout the BAR Phase I project. Overall, the BAR project has identified low-SP turbines as important to continued LCOE reductions for onshore turbines. Furthermore, the project has identified viable solutions to the technical and logistical challenges to realizing these goals. The most promising technologies that were identified in Phase I of the project will be further matured and de-risked in Phase II of the BAR project.

17 WIND ENERGY↗

DOE OSTI2020

On the spectral behaviour of the turbulence-driven power fluctuations of horizontal-axis turbines

In this article we consider the spectral behaviour of turbulence-driven power fluctuations for a single horizontal-axis turbine. To this end, a small-scale instrumented axial-flow hydrokinetic turbine model ( diameter=0.724 m ) is deployed in the long water flume situated in the laboratory facilities of IFREMER in Boulogne-sur-Mer, France, and synchronous measurements of the upstream velocity and the rotor are collected for different tip-speed ratios. The study confirms previous findings suggesting that the power spectra follow the velocity spectra behaviour in the large scales region and a steeper power law slope behaviour ( -11/3 ) over the inertial frequency sub-range. However, we show that both the amplitude of the power spectra and low-pass filtering effect over the inertial sub-range also depend on the rotor aero/hydrodynamics (e.g. dC L /dα) and the approaching flow deceleration and not solely on the rotational effects. In addition, we present a novel semi-analytical model to predict the dominant blade-passing frequency harmonics in the high-frequency regime using the rotationally sampled spectra technique. For all calculations, the distortion of incoming turbulence is taken into account.

42 ENGINEERING↗

DOE OSTI2020

The Effects of Wind Veer During the Morning and Evening Transitions

Direction and speed wind shear modify turbine performance by changing inflow conditions on turbine blades. Using observations from the 2013 CWEX campaign, we found the daily atmospheric boundary layer transitions (morning and evening) match periods of high electricity demand for a wind farm in central Iowa. Power production during these periods was undermined for large direction shear and low speed shear scenarios. The morning transition displayed larger direction shear over the rotor layer for most wind speeds compared to the evening period. This resulted in lower turbine performance for the morning compared to the evening and whole day. This study shows that the combined effect of direction and speed shear is affecting turbine operation during high electricity demand times of day, predominantly during the morning at this wind farm.

17 WIND ENERGY↗