Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impurity concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Degradation Mode Identification by Photocarrier Lifetime Spectroscopy on Devices and Test Structures

In this presentation, I examine the basic concepts of the device physics that can be used to distinguish various degradation and recovery modes on a cell level. The known degradation modes (bulk LeTID and LID, UVID, etc.) are due to defects and impurities that cause the photocarrier recombination according to Shockley-Reed-Hall (SRH) statistics. The SRH recombination rate strongly depends on the balance of electron and hole capture rates into the defects, which in turn, are governed by their local concentrations. The strongest recombination takes place at approximately equal concentrations of electrons and holes, while at low injection conditions (when one type of carrier dominates) the SRH recombination is suppressed. For cell degradation modes that affect the passivated interface (UVID, H-induced TOPCon contact degradation) the defects are at the interface under low-injection conditions due to either high local doping or the adjacent built-in charge in the dielectric. This mode is characterized by changes in the "diode prefactor" J01 slope in the inverse lifetime-injection level curve. In contrast, bulk degradation (LeTID, LID) affects bulk lifetime, with J01 slope unchanged. Carrier lifetime - injection level plots therefore serve as clear indicators of different degradation modes and are shown by experimental examples.

14 SOLAR ENERGY↗
NASA NTRS1984

Oxygen in GaAs - Direct and indirect effects

Oxygen has profound effects on the key electronic properties and point defects of GaAs crystals. Thus, when added in the growth system, it decreases the free electron concentration and enhances the concentration of deep donors in the resulting crystals. Both of these effects are highly beneficial for achieving semi-insulating material and have been utilized for that purpose. They have been attributed to the tendency of oxygen to getter silicon impurities during crystal growth. Only recently, it has been found that oxygen in GaAs introduces also a midgap level, ELO, with essentially the same activation energy as EL2 but with four times greater electron capture cross section. The present report reassesses the electrical and optical properties of the midgap levels in GaAs crystals grown by the horizontal Bridgman (HB) and the Czochralski-LEC techniques. Emphasis is placed on the identification of the specific effects of ELO.

Gatos, H. C.↗
DOE OSTI2025

Synthesis of Yttrium Oxide Particles for Interfacial Water Radiolysis Studies

Radiolysis of water produces hydrogen gas (H2), posing safety issues for nuclear reactors. Metal oxides can impact H2 formation when water is present on metal oxide surfaces. This presentation focuses on the development of a controllable synthesis of spherical yttrium oxide (Y2O3), that later will be tested for H2 production in water radiolysis. Y2O3 was synthesized via hydrothermal hydrolysis precipitation to form yttrium hydroxide (Y(OH)3), followed by high temperature decomposition to form Y2O3. Various synthesis conditions were tested to determine their impact on particle morphology including reaction time, cooling rate, reactant concentration, and inert atmospheres. Through short reaction times and rapid cooling rate, spherical, relatively uniform particles of 350 nm were obtained. Despite inert atmospheres, carbonate formation occurred in all particles. A calcination temperature of 800°C is necessary to remove impurities. Future work will aim to reduce carbonate formation and improve particle uniformity. The synthetic procedure will be translated to other metal ions to study their impact on interfacial radiolysis.

08 - HYDROGEN↗
DOE OSTI2024

Effect of Carbon on Void Nucleation in Iron

The study reports the significance of carbon presence in affecting void nucleation in Fe. Without carbon, void nucleation rates decrease gradually at high temperatures but remain significantly high and almost saturated at low temperatures. With carbon present, even at 1 atomic parts per million, void nucleation rates show a low-temperature cutoff. With higher carbon levels, the nucleation temperature window becomes narrower, the maximum nucleation rate becomes lower, and the temperature of maximum void nucleation shifts to a higher temperature. Fundamentally, this is caused by the change in effective vacancy diffusivity due to the formation of carbon-vacancy complexes. The high sensitivity of void nucleation to carbon comes from the high sensitivity of void nucleation to the vacancy arrival rate in a void. The void nucleation is calculated by first obtaining the effective vacancy diffusivity considering the carbon effect, then calculating the defect concentration and defect flux change considering both carbon effects and pre-existing dislocations, and finally calculating the void nucleation rate based on the recently corrected homogeneous void nucleation theory. The study is important not only in the fundamental understanding of impurity effects in ion/neutron irradiation but also in alloy engineering for judiciously introducing impurities to increase swelling resistance, as well as in the development of simulation and modeling methodologies applicable to other metals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Spatial variation of the low-temperature micro-photoluminescence of THM-grown CdZnTeSe

The quaternary compound CdZnTeSe (CZTS) has emerged as a next-generation detector material. Unlike CdZnTe (CZT), CZTS has the distinct advantages of little or no sub-grain boundary networks and a much lower concentration of Te inclusions, plus better compositional homogeneity. Thus, the material is expected to offer better spatial charge-transport homogeneity compared to CZT. However, an inhomogeneous distribution of point defects in both CZT and CZTS, such as Cd vacancies and residual impurities, can impose additional spatial inhomogeneity of the resistivity, carrier mobilities, and carrier lifetimes of the material. To investigate the spatial distribution of such defects in CZTS, low-temperature photoluminescence (PL) spectroscopic studies were performed at different positions along a single crystalline CZTS sample surface, which was grown by the traveling heater method (THM). In conclusion, the intensity variation of the PL emission of excitons bound to a neutral acceptor defect (A 0 , X), which is likely dominated by an acceptor like Cu-related level, with respect to the PL emission line from a neutral donor-bound exciton (D 0 , X) exhibited significant spatial variation, while the peak energy positions were approximately uniform due to the high compositional and bandgap homogeneity of the material.

II-VI semiconductor↗
NASA NTRS1986

Process-induced defects in solar cell silicon

The microstructure of as-grown and processed, edge-defined film-fed grown, silicon ribbons was studied in order to identify the basic mechanisms responsible for the change of the as-grown defect structure during processing at elevated temperatures. The short heat treatment required to diffuse the p-n junction was sufficient to cause heterogeneous precipitation of impurity atoms, particularly transition metals. In addition, an elastic recovery of the ribbon occurred by dislocation glide, resulting in the formation of a polygonizationlike structure of subboundaries in the base. Mechanisms are suggested by which twin boundaries, acting as dislocation obstacles, can concentrate the relatively low average dislocation densities typical of edge-defined film-fed grown ribbons (10 to the 4th to 10 to the 8th/sq cm) to values which are sufficient to induce the formation of subgrainlike boundary structures.

Gleichmann, R.↗
NASA NTRS1982

Effect of aluminum phosphate additions on composition of three-component plasma-sprayed solid lubricant

Image analysis (IA) and electron microprobe X-ray analysis (EMXA) were used to characterize a plasma-sprayed, self-lubricating coating, NASA LUBE PS106, specified by weight percent as 35NiCr-35Ag-30CaF2. To minimize segregation of the powder mixture during the plasma-spraying procedure, monoaluminum phosphate was added to form agglomerate particles. Three concentrations of AlPO4 were added to the mixtures: 1.25, 2.5, and 6.25 percent by weight. Analysis showed that 1.25 wt% AlPO4 yielded a CaF2 deficiency, 2.5 wt% kept the coating closest to specification, and 6.25 wt% yielded excess CaF2 as well as more impurities and voids and a deficiency in silver. Photomicrographs and X-ray maps are presented. The methods of IA and EMXA complement each other, and the reasonable agreement in the results increases the confidence in determining the coating composition.

Jacobson, T. P.↗
DOE OSTI2021

Progress in Uranium Chemistry: Driving Advances in Front-End Nuclear Fuel Cycle Forensics

The front-end of the nuclear fuel cycle encompasses several chemical and physical processes used to acquire and prepare uranium for use in a nuclear reactor. These same processes can also be used for weapons or nefarious purposes, necessitating the need for technical means to help detect, investigate, and prevent the nefarious use of nuclear material and nuclear fuel cycle technology. Over the past decade, a significant research effort has investigated uranium compounds associated with the front-end of the nuclear fuel cycle, including uranium ore concentrates (UOCs), UF 4 , UF 6 , and UO 2 F 2 . These efforts have furthered uranium chemistry with an aim to expand and improve the field of nuclear forensics. Focus has been given to the morphology of various uranium compounds, trace elemental and chemical impurities in process samples of uranium compounds, the degradation of uranium compounds, particularly under environmental conditions, and the development of improved or new techniques for analysis of uranium compounds. Overall, this research effort has identified relevant chemical and physical characteristics of uranium compounds that can be used to help discern the origin, process history, and postproduction history for a sample of uranium material. This effort has also identified analytical techniques that could be brought to bear for nuclear forensics purposes. Continued research into these uranium compounds should yield additional relevant chemical and physical characteristics and analytical approaches to further advance front-end nuclear fuel cycle forensics capabilities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1996

Observations of Dynamic Strain Aging in Polycrystalline NiAl

Dynamic strain aging has been investigated at temperatures between 77 and 1100 K in eight polycrystalline NiAl alloys. The 0.2% offset yield stress and work hardening rates for these alloys generally decreased with increasing temperature. However, local plateaus or maxima were observed in conventional purity and carbon doped alloys at intermediate temperatures (600-900 K). This anomalous behavior was not observed in low interstitial high-purity, nitrogen doped, or in titanium doped materials. Low or negative strain rate sensitivities (SRS) were also observed in all eight alloys in this intermediate temperature range. Coincident with the occurrence of negative SRS was the occurrence of serrated flow in conventional purity alloys containing high concentrations of Si in addition to C. These phenomena have been attributed to dynamic strain aging (DSA). Chemical analysis of the alloys used in this study suggests that the main species causing strain aging in polycrystalline NiAl is C but indicate that residual Si impurities can enhance the strain aging effect.

Weaver, M. L.↗
DOE OSTI2021

Thermodynamics of boron incorporation in BGaN

We study the thermodynamics of boron (B) incorporation into gallium nitride (GaN) using first-principles calculations. In the dilute limit, we have calculated the formation energies of different configurations of the B impurity in GaN and found that substitution on the cation site is favored over substitution on the anion site. Furthermore, under p-type conditions, interstitial boron can become the more favorable configuration and will ultimately limit the p-type conductivity. At higher B concentrations we use the generalized quasi-chemical approximation to elucidate the thermodynamic stability of boron gallium nitride (BGaN) alloys. We also investigate the effects of strain, which will be present if BGaN alloys are grown pseudomorphically on a GaN substrate.Without strain, B incorporation at typical growth conditions is limited to about 1.4% at 800 °C. Pseudomorphic strain raises the limit to 3.0% at the same temperature, close to experimentally observed levels of B incorporation.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Recent progress in picosecond pulse generation from semiconductor lasers

This paper reviews the recent progress in producing picosecond optical pulses from semiconductor laser diodes. The discussion concentrates on the mode-locking of a semiconductor laser diode in an external resonator. Transform-limited optical pulses ranging from several picoseconds to subpicosecond durations have been observed with active and passive mode-locking. Even though continuing research on the influence of impurities and defects on the mode-locking process is still needed, this technique has good promise for being utilized in fiber-optic communication systems. Alternative methods of direct electrical and optical excitation to produce ultrashort laser pulses are also described. They can generate pulses of similar widths to those obtained by mode-locking. The pulses generated will find applications in laser ranging and detector response measurement.

Auyeung, J. C.↗
DOE OSTI2025

Effect of Mg and Ni impurities on tritium diffusion in lithium ceramics through cluster dynamics simulations

This study investigates the impact of Mg and Ni doping on tritium diffusion in LiAlO 2 and LiAl 5 O 8 ceramics, that are used in tritium-producing burnable absorber rods (TPBARs). Utilizing Centipede simulations across a broad temperature range (500 K to 1250 K), we explore the interplay between defect dynamics, cluster formation, and tritium mobility. In LiAlO 2 , Mg doping significantly enhances tritium diffusivity by increasing tritium interstitial concentrations and diffusion coefficients of key species, thereby doubling the overall tritium diffusivity. Ni doping, while shifting the dominant defect to Li vacancies, maintains high tritium mobility due to the low binding energy of Li vacancy-tritium complexes, which ensures effective tritium migration. In LiAl 5 O 8 , Mg and Ni doping results in a slight reduction in the diffusion coefficients of key species, yet the dramatic increase in tritium interstitial concentrations compensates, leading to a net small increase in tritium diffusivity. In conclusion, the findings highlight the critical role of defects in tritium transport and the effect of Mg and Ni defects on the performance of these ceramics in demanding nuclear environments.

Cluster dynamics↗
DOE OSTI2023

Sequential Recovery of Critical Metals from Leached Liquor of Processed Spent Lithium-Ion Batteries

The processing and extraction of critical metals from black mass is important to battery recycling. Separation and recovery of critical metals (Co, Ni, Li, and Mn) from other metal impurities must yield purified metal salts, while avoiding substantial losses of critical metals. Solvent extraction in batch experiments were conducted using mixed metal sulphates obtained from the leach liquor obtained from spent and shredded lithium-ion batteries. Selective extraction of Mn 2+ , Fe 3+ , Al 3+ and Cu 2+ from simulated and real leached mixed metals solution was carried out using di-2-ethylhexylphophoric acid (D2EPHA) and Cyanex-272 at varying pH. Further experiments with the preferred extractant (D2EPHA) were performed under different conditions: changing the concentration of extractant, organic to aqueous ratio, and varying the diluents. At optimum conditions (40% v/v D2EPHA in kerosene, pH 2.5, O:A = 1:1, 25 °C, and 20 min), 85% Mn 2+ , 98% Al 3+ , 100% Fe 3+ , and 43% Cu 2+ were extracted with losses of only trace amounts (<5.0%) of Co 2+ , Ni 2+ , and Li + . The order of extraction efficiency for the diluents was found to be kerosene > Exxal-10 >>> dichloromethane (CH 2 Cl 2 ) > toluene. Four stages of stripping of metals loaded on D2EPHA were performed as co-extracted metal impurities were selectively stripped, and a purified MnSO 4 solution was produced. Spent extractant was regenerated after Fe 3+ and Al 3+ were completely stripped using 1.0 M oxalic acid (C 2 H 2 O 4 ).

25 ENERGY STORAGE↗
DOE OSTI2025

Hydrogen and water interactions with CrMnFeCoNi alloy from density functional theory calculations

High entropy alloys (HEAs) are a promising class of materials with remarkable mechanical and catalytic properties. Among these, the quinary CrMnFeCoNi alloy (also called “Cantor alloy”) has attracted considerable attention given its thermodynamic stability and remarkable mechanical properties under different temperatures. Given that various degradation mechanisms involve multiple contaminants, such as hydrogen and water in hydrogen embrittlement and surface poisoning, respectively, understanding their interactions with the Cantor alloy is critical for its practical applications as structural, nuclear, or hydrogen storage material. In this work, we perform first-principles calculations based on Density Functional Theory (DFT) to investigate such interactions when considering various microstructures, including bulk materials and those containing certain defects, such as grain boundaries, stacking faults, and vacancies. We also employ Global Sensitivity Analysis to identify the importance of different factors in the stability of the impurities. We find that the accuracy of the H formation energy is significantly affected by spin polarization and chemical short-range order. The study also identifies a strong tendency for hydrogen interstitials to segregate to Σ5(210)/[001] symmetric tilt grain boundary, even when H concentrations are high, suggesting that a certain type of grain boundaries acts as H sinks within the alloy. Further, this result is reinforced by the low formation energy of vacancy-hydrogen complexes, which can contain multiple hydrogen atoms. Finally, the surface reactivity analysis reveals that the adsorption energy of oxygen and hydroxyl groups is highly sensitive to the specific metal atom involved in the binding, with a clear preference for chromium atoms, which could have implications for the alloy’s oxidation and corrosion behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mapping out the emergence of topological features in the highly alloyed topological Kondo insulators Sm 1-$x$ M $x$ B 6 ( M =Eu, Ce)

SmB 6 is a strongly correlated material that has been attributed as a topological insulator and a Kondo insulator. Recent studies have found the topological surface states and low temperature insulating character to be profoundly robust against magnetic and nonmagnetic impurities. Here, we use angle resolved photoemission spectroscopy to chart the evolution of topologically linked electronic structure features versus magnetic doping and temperature in Sm 1-$x$ M $x$ B 6 ( M =Eu, Ce). Topological coherence phenomena are observed out to ~30% Eu and 50% Ce concentrations that represent extreme nominal hole and electron doping, respectively. Finally, theoretical analysis reveals that a recent redesignation of the topologically inverted band symmetries provides a natural route to reconciling the persistence of topological surface state emergence even as the insulating gap is lost through decoherence.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Shock tube study of ionization rates of NaCl-contaminated argon

Spectrally resolved radiometry and a microwave technique were used to measure the electron density, electron temperature, and concentration, and the concentration of sodium atoms in the weakly ionized region behind a shock wave in an argon shock tube. It is shown that the observed increase in the ionization rate is due to electron detachment of negative chlorine ions produced from sodium chloride vapor contained as an impurity in the argon gas. The observed behavior of the electron temperature in time and the reactions controlled by the electron temperature are analyzed in the light of the impurity reaction scheme.

Scheneider, C.-P.↗
DOE OSTI2020

Redox Potential Measurements of Cr(II)/Cr Ni(II)/Ni and Mg(II)/Mg in Molten MgCl 2 –KCl–NaCl Mixture

The redox potential of Ni(II)/Ni, Cr(II)/Cr, and Mg(II)/Mg in MgCl 2 –KCl–NaCl (Magnak chloride) were studied utilizing chronopotentiometry (CP) method in a three-electrode electrochemical cell. Four different CrCl 2 concentrations from 873 K to 1073 K, three NiCl 2 concentrations from 773 K to 1073 K, and two MgCl 2 concentrations from 823 K to 1073 K have been measured. The activity coefficients were calculated referring to a supercooled potential accordingly. The empirical equation of formal potential will be of great significance for the fundamental thermodynamic prediction in high-temperature Magnak chloride systems where corrosion product impurities are present.

14 SOLAR ENERGY↗
NASA NTRS2001

Photoluminescence Studies of ZnSe Starting Materials and Vapor Grown Bulk Crystals

Low-temperature photoluminescence (PL) spectra were measured on ZnSe starting materials provided by various vendors and on bulk crystals grown from these starting materials by physical vapor transport (PVT) to study the effects of purification and contamination during PVT process. The impurity levels in one set of starting material/grown crystal were also measured by glow discharge mass spectroscopy (GDMS). The purification effect of pre-growth heat treatments and the PVT process is evidenced from the GDMS results which showed orders of magnitude reduction in the Li and Na concentration and a factor of 3 reduction in the O content after growth. The PL spectra showed that the strong emissions associated with Li (or Na) in one of the starting materials disappeared after growth. The GDMS results also showed increases in the At and Si contents by orders of magnitude after growth. To evaluate the contamination of the crystal during the high temperature growth process, three growth runs were processed using similar growth parameters but different furnace environments. The PL spectra suggest that the At contamination originated from the fused silica ampoule and that the Inconel cartridge might have been the cause of the broad Cu green and Cu red bands observed in one of the grown crystals.

Su, Ching-Hua↗