Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heat engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Orbit transfer rocket engine technology program enhanced heat transfer combustor technology

In order to increase the performance of a high performance, advanced expander-cycle engine combustor, higher chamber pressures are required. In order to increase chamber pressure, more heat energy is required to be transferred to the combustor coolant circuit fluid which drives the turbomachinery. This requirement was fulfilled by increasing the area exposed to the hot-gas by using combustor ribs. A previous technology task conducted 2-d hot air and cold flow tests to determine an optimum rib height and configuration. In task C.5 a combustor calorimeter was fabricated with the optimum rib configuration, 0.040 in. high ribs, in order to determine their enhancing capability. A secondary objective was to determine the effects of mixture ratio changers on the enhancement during hot-fire testing. The program used the Rocketdyne Integrated Component Evaluator (ICE) reconfigured into a thrust chamber only mode. The test results were extrapolated to give a projected enhancement from the ribs for a 16 in. long cylindrical combustor at 15 Klb nominal thrust level. The hot-gas wall ribs resulted in a 58 percent increase in heat transfer. When projected to a full size 15K combustor, it becomes a 46 percent increase. The results of those tests, a comparison with previous 2-d results, the effects of mixture ratio and combustion gas flow on the ribs and the potential ramifications for expander cycle combustors are detailed.

Brown, William S.↗
NASA NTRS2010

RP-2 Thermal Stability and Heat Transfer Investigation for Hydrocarbon Boost Engines

A series of electrically heated tube tests were performed at the NASA Glenn Research Center s Heated Tube Facility to investigate the use of RP-2 as a fuel for next generation regeneratively cooled hydrocarbon boost engines. The effect that test duration, operating condition and test piece material have on the overall thermal stability and materials compatibility characteristics of RP-2 were evaluated using copper and 304 stainless steel test sections. The copper tests were run at 1000 psia, heat flux up to 6.0 Btu/in.2-sec, and wall temperatures up to 1180 F. Preliminary results, using measured wall temperature as an indirect indicator of the carbon deposition process, show that in copper test pieces above approximately 850 F, RP-2 begins to undergo thermal decomposition resulting in local carbon deposits. Wall temperature traces show significant local temperature increases followed by near instantaneous drops which have been attributed to the carbon deposition/shedding process in previous investigations. Data reduction is currently underway for the stainless steel test sections and carbon deposition measurements will be performed in the future for all test sections used in this investigation. In conjunction with the existing thermal stability database, these findings give insight into the feasibility of cooling a long life, high performance, high-pressure liquid rocket combustor and nozzle with RP-2.

VanNoord, J. L.↗
NASA NTRS2012

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Icing Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU and the future flight unit are considered.

Padilla, Sebastian A.↗
NASA NTRS2011

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Ice Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously each the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU to the future flight unit are considered.

Padilla, Sebastian A.↗
NASA NTRS1993

Performance and heat transfer characteristics of a carbon monoxide/oxygen rocket engine

The combustion and heat transfer characteristics of a carbon monoxide and oxygen rocket engine were evaluated. The test hardware consisted of a calorimeter combustion chamber with a heat sink nozzle and an eighteen element concentric tube injector. Experimental results are given at chamber pressures of 1070 and 3070 kPa, and over a mixture ratio range of 0.3 to 1.0. Experimental C efficiency was between 95 and 96.5 percent. Heat transfer results are discussed both as a function of mixture ratio and axial distance in the chamber. They are also compared to a Nusselt number correlation for fully developed turbulent flow.

Linne, Diane L.↗
NASA NTRS1977

Aircraft community noise impact studies

The objectives of the study are to: (1) conduct a program to determine the community noise impact of advanced technology engines when installed in a supersonic aircraft, (2) determine the potential reduction of community noise by flight operational techniques for the study aircraft, (3) estimate the community noise impact of the study aircraft powered by suppressed turbojet engines and by advanced duct heating turbofan engines, and (4) compare the impact of the two supersonic designs with that of conventional commercial DC-8 aircraft.

Source record↗
NASA NTRS1979

Several preliminary designs for heavy-lift earth-to-orbit transport

Several design concepts are identified for earth-to-orbit delivery of payloads in the 200 Mg range. The concept include winged vehicles which take-off vertically and land horizontally and ballistic shapes similar to the Gemini or Mercury vehicles which take-off and land vertically. Major technology issues include stability problems for the winged vehicle with large base mounted engines and heat shield design problems for the ballistic vehicle, the latter requiring doors in the heat shield for the main engines.

Brien, E. P.↗
NASA NTRS2018

Design Options for a Versatile Nuclear Thermal Propulsion (NTP) Stage

A study was initiated to investigate propulsion stage and mission architecture options potentially enabled by fission energy. One initial concept is a versatile Nuclear Thermal Propulsion (NTP) system with a maximum specific impulse of 900 s and a maximum thrust (per engine) of 15 klbf. The system assumes a monopropellant stage (hydrogen), and is designed to also provide 300 lbf of thrust (potentially split between multiple thrusters) at an Isp > 500 s. Boost pumps are used to assist with engine decay heat removal and low thrust engine burns, and to compensate for partial tank depressurization during full thrust engine burns. Potential stage assembly orbits that take full advantage of launch vehicle payload mass and volume capabilities are being assessed. The potential for using NTP engines to also generate a small to moderate amount of electrical power is also being evaluated.

Fission Power Propulsion↗
NASA NTRS2019

Versatile Nuclear Thermal Propulsion (NTP)

A study was initiated to investigate propulsion stage and mission architecture options potentially enabled by fission energy. One initial concept is a versatile Nuclear Thermal Propulsion (NTP) system with a maximum specific impulse of 900 s and a maximum thrust (per engine) of 15 klbf. The system assumes a monopropellant stage (hydrogen), and is designed to also provide 300 lbf of thrust (potentially split between multiple thrusters) at an Isp > 500 s for orbital maneuvering and station keeping. Boost pumps are used to assist with engine decay heat removal and low thrust engine burns, and to compensate for partial tank depressurization during full thrust engine burns. Potential stage assembly orbits that take full advantage of launch vehicle payload mass and volume capabilities are being assessed. The potential for using NTP engines to also generate a small to moderate amount of electrical power is also being evaluated. A first generation versatile NTP stage could enable 8 of 9 upcoming opportunities for short (less than 24 month) round trip human missions to Mars. A second generation versatile NTP is under consideration that could potentially provide a maximum specific impulse of 1800 s at 15 klbf, and enable ambitious missions throughout the solar system. The second generation NTP system under consideration would also allow a choice of volatiles to be used as propellant. This would potentially allow in-situ resources such as water, ammonia, methane, or other compounds to be used directly as propellant by the second generation engine.

Houts, Michael G.↗
NASA NTRS2019

Versatile Nuclear Thermal Propulsion (NTP)

A study was initiated to investigate propulsion stage and mission architecture options potentially enabled by fission energy. One initial concept is a versatile Nuclear Thermal Propulsion (NTP) system with a maximum specific impulse of 900 s and a maximum thrust (per engine) of 15 klbf. The system assumes a monopropellant stage (hydrogen), and is designed to also provide 300 lbf of thrust (potentially split between multiple thrusters) at an Isp > 500 s for orbital maneuvering and station keeping. Boost pumps are used to assist with engine decay heat removal and low thrust engine burns, and to compensate for partial tank depressurization during full thrust engine burns. Potential stage assembly orbits that take full advantage of launch vehicle payload mass and volume capabilities are being assessed. The potential for using NTP engines to also generate a small to moderate amount of electrical power is also being evaluated. A first generation versatile NTP stage could enable 8 of 9 upcoming opportunities for short (less than 24 month) round trip human missions to Mars. A second generation versatile NTP is under consideration that could potentially provide a maximum specific impulse of 1800 s at 15 klbf, and enable ambitious missions throughout the solar system. The second generation NTP system under consideration would also allow a choice of volatiles to be used as propellant. This would potentially allow in-situ resources such as water, ammonia, methane, or other compounds to be used directly as propellant by the second generation engine.

Houts, Mike↗
DOE OSTI2026

Concept of Dynamic Heat Insulation for Rotating Detonation Engines

This work introduces a new class of materials concept to dynamically reduce instantaneous heat fluxes in Rotating Detonation Engine (RDE) combustor chamber walls. The high-frequency and high-amplitude surface heat fluxes observed in RDEs arise from large instantaneous temperature differences between the detonation shockwave and chamber wall surface. These temperature gradients drive substantial energy loss and reduce the chamber gas pressure, ultimately limiting the cycle’s thermodynamic efficiency. This work introduces a concept for dynamically insulating the combustion chamber surfaces using surface layers or coatings with low thermal time scale. With such coatings, the surface temperature may follow the fluctuations of the cyclic detonation wave temperature, thus reducing the instantaneous heat flux therefore cycle-mean heat flux. To analyze these cyclic thermal phenomena, a one-dimensional analytical conduction solver was utilized with the capability to handle multilayered structures. Parametric modeling was performed using transient heat flux boundary conditions representative of a hydrogen–air RDE across a broad range of coating thermal properties and engine conditions. The coating effectiveness scaled with the product of thermal time constant and detonation wave frequency and the results were non-dimensionalized to guide future materials development. This strategy may offer benefits in increasing material survivability, reducing cooling requirements, and enhancing pressure gain.

heat transfer↗
NASA NTRS1984

Heat pipes to reduce engine exhaust emissions

A fuel combustor is presented that consists of an elongated casing with an air inlet conduit portion at one end, and having an opposite exit end. An elongated heat pipe is mounted longitudinally in the casing and is offset from and extends alongside the combustion space. The heat pipe is in heat transmitting relationship with the air intake conduit for heating incoming air. A guide conduit structure is provided for conveying the heated air from the intake conduit into the combustion space. A fuel discharge nozzle is provided to inject fuel into the combustion space. A fuel conduit from a fuel supply source has a portion engaged in heat transfer relationship of the heat pipe for preheating the fuel. The downstream end of the heat pipe is in heat transfer relationship with the casing and is located adjacent to the downstream end of the combustion space. The offset position of the heat pipe relative to the combustion space minimizes the quenching effect of the heat pipe on the gaseous products of combustion, as well as reducing coking of the fuel on the heat pipe, thereby improving the efficiency of the combustor.

Schultz, D. F.↗
NASA NTRS1989

Shock-Induced Heating In A Rocket Engine

Misalignments give rise to hotspots on walls. Report discusses numerical simulation of flow in and near small, ringlike cavity in wall of Space Shuttle main engine at junction of main combustion chamber and nozzle. Purpose to study effects of misalignments between combustion chamber and nozzle on transfer of heat into surfaces chamber, cavity, and nozzle. Depending on specific misalignment flow encounters forward-or backward-facing step leaving chamber and entering nozzle. Results in serious losses of performance and excessive heating of walls.

Lagnado, Ronald R.↗
NASA NTRS1985

Two-Phase Wet/Dry Engine for Waste-Heat Recovery

Novel supersonic fluid expansion nozzle used to vaporize toluene (or other drying-type organic liquid) by expansion through two-phase region to drive impulse turbine in Rankine-cycle engine.

Elliott, D. G.↗