Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Electron beam induced damage in ITO coated Kapton

Data for the stability of thin conductive indium tin oxide films on 0.003 inch thick Kapton substrates during exposure of the surface to electron beams are reported. The electron beam energy was 3 keV and the diameter was about 0.8 mm. Thermal effects and surface modifications are considered. For primary current greater than 0.6 microamperes, an obvious dark discoloration with diameter approximately that of the beam was produced. The structure of the discolored region was studied with the scanning electron microscope, and the findings are stated. Surface modifications were explored by AES, obtaining spectra and secondary emission coefficient as a function of time for different beam intensities. In all cases beam exposure results in a decrease of the secondary yield but because of thermal effects this change, as well as composition changes, cannot be directly interpreted in terms of electron beam dosage.

Krainsky, I.↗
NASA NTRS2005

Diode Laser Sensors for Arc-Jet Characterization

The development and application of tunable diode laser (TDL) absorption sensors to monitor the health and operating conditions in the large-scale 60 MW arc-heated- plasma wind-tunnel at NASA Ames Research Center is reported. The interactive heating facility (THF) produces re-entry flow conditions by expanding the gas heated in a constricted plasma arc-heater to flow at high velocity over a model located in a test cabin. This facility provides the conditions needed to test thermal protective systems for spacecraft re-entering the earth s atmosphere. TDL sensors are developed to monitor gas flows in both the high-temperature constricted flow and the supersonic expansion flow into test cabin. These sensors utilize wavelength-tuned diode lasers to measure absorption transitions of atomic oxygen near 777.2 nm, atomic nitrogen near 856.8 nm, and atomic copper near 793.3 nm. The oxygen and nitrogen sensors measure the population density in exited electronic states of these atoms. The measurements combined with the assumption of local thermal and chemical equilibrium yield gas temperature (typically near 7,000K). The nitrogen and oxygen population temperatures are redundant, and their close agreement provides an important test of the local thermal equilibrium assumption. These temperature sensors provide time-resolved monitors of the operating conditions of the arc-heater and can be used to verify and control the test conditions. An additional TDL sensor was developed to monitor the copper concentration in the arc-heater flow yielding values as high as 13 ppm. Measurements of copper in the flow can identify flow conditions with unacceptably rapid electrode erosion, and hence this sensor provides valuable information needed to schedule maintenance to avoid costly arc-heater failure. TDL sensors were also developed for measurements in the test cabin, where absorption measurements of the populations of argon and molecular nitrogen in excited metastable electronic states established that the number density of these excited species is much lower than estimated using frozen-chemistry approximations. This key finding suggests that in the post-expansion region there is not a significant energy sequestration in electronically excited species. Finally, TDL measurements of atomic potassium seeded into the test cabin flow were used to directly measure the static temperature of the test gas. The results of this study illustrate the high potential of time-resolved TDL measurements for routine and economical sensing of arc-heater health (gas temperature and electrode erosion) as well as the time-resolved test-cabin-flow conditions in front of the model.

Hanson, Ronald K.↗
NASA NTRS1997

Ballistics-Electron-Microscopy and Spectroscopy of Metal/GaN Interfaces

BEEM spectroscopy and imaging have been applied to the Au/GaN interface. In contrast to previous BEEM measurements, spectra yield a Schottky barrier height of 1.04eV that agrees well with the highest values measured by conventional methods.

ballistic-electron-emission microscopy spectroscop↗
NASA NTRS1992

Giotto data analysis: Electron plasma and heavy ion composition measurements at Comet Halley

This investigation involved the analysis of electron plasma and heavy ion composition measurements made by the COPERNIC (COmplete Positive ion, Electron, and Ram Negative Ion measurements near Comet Halley) plasma experiment during the close fly-by of Halley by the European Space Agency's Giotto spacecraft. The experiment provided measurements of the full 3-dimensional distribution of 10 eV-30 keV electrons, and mass analysis of cold cometary ions from 10-210 amu. The analysis of the COPERNIC data has yielded some remarkable results, including: The discovery of negatively charged ions in the inner coma; the discovery of far heavier (mass is greater than 50 amu) ions than predicted, dominated by complex molecular ions made up of C, H, O, and N; the discovery of an adiabatic heating effect on electrons from the compression of the solar wind plasma; the identification of several organic and sulfur bearing ions; and the discovery of a new 'mystery region' where electrons are accelerated to high energies. These discoveries were in addition to the detailed analysis of 'expected' features at Comet Halley. Although this grant has expired, analysis continues on the data at a low (unfunded) level, and it is expected that more significant results will be obtained. A bibliography of the papers resulting from this research is attached, and a copy of each paper is included.

Lin, Robert P.↗
NASA NTRS1975

Auroral N2 vibrational excitation and the electron density trough

Through various processes molecular nitrogen within the nocturnal auroral oval is vibrationally excited, substantially increasing the rate at which O(+) is lost via the reaction O(+) + N2* yields NO(+) + N. Owing to the action of thermospheric winds and diffusion, N2* does not remain at its point of origin but is transported to regions outside the auroral oval where it can act to substantially reduce the F-region electron density. For an equatorward transport speed of 100 m/sec, N2* can travel 3 to 4 deg of latitude before quenching with atomic oxygen substantially reduces the N2* density. This process may contribute significantly to the formation of the midlatitude F-region electron density trough.

Schunk, R. W.↗
NASA NTRS1992

Optical-Input, Optical-Output Morphological Processor

Some advantages of optical and electronic processing combined. Proposed optical-input/optical-output morphological processor is optoelectronic assembly performing some binary operations on picture elements of binary input image, yielding processed binary output image. Number of such processors cascaded to form more complicated image-processing system. Use of optics as connection medium makes rate of processing faster than in all-electronic system designed to perform same overall processing functions. At the same time, use of electronics as processing medium provides flexibility of reconfiguration not available in all-optical system.

Yu, Jeffrey W.↗
NASA NTRS1973

Electrical screening procedure for solid ionic conductors

An electrical screening method has been developed for preliminary evaluation of polycrystalline specimens of candidates for use as solid ionic conductive electrolytes in batteries. The procedure measures dielectric loss and capacitance, from which are calculated an ac conductivity attributed provisionally to ions and an activation energy for that conductivity. Electronic conductivity is directly measured. The screening procedure applied to sodium beta-alumina yielded acceptable values for conductivity and activation energy.

Kautz, H. E.↗
NASA NTRS1983

A threshold effect for spacecraft charging

The borderline case between no charging and large (kV) negative potentials for eclipse charging events on geosynchronous satellites is investigated, and the dependence of this transition on a threshold energy in the ambient plasma is examined. Data from the Applied Technology Satellite 6 and P78-2 (SCATHA) show that plasma sheet fluxes must extend above 10 keV for these satellites to charge in eclipse. The threshold effect is a result of the shape of the normal secondary yield curve, in particular the high energy crossover, where the secondary yield drops below 1. It is found that a large portion of the ambient electron flux must exceed this energy for a negative current to exist.

Olsen, R. C.↗
NASA NTRS1989

On the bonding in Mn2(+)

Qualitative calculations are presented on the Mn2(+) ion. These yield a 12Sigma(g)(+) ground state, in agreement with experiment, in which the 3d electrons are ferromagnetically coupled. The 2Sigma(u)(+) state of Mu2(+) is found to lie 0.44 eV higher in energy; the 3d electrons on each center are high-spin coupled, but the interatomic coupling is antiferromagnetic. The large splitting between the 12Sigma(g)(+) and 2Sigma(u)(+) states is shown to be due to the intraatomic 4s-3d exchange energy, which is an order of magnitude larger than the weak interatomic 3d-3d interaction. The Mn2(+) ion is compared and contrasted with the Mn2 neutral species, where the analogous 11Sigma(u)(+) and 1Sigma(g)(+) states are reversed in order, but almost degenerate.

Bauschlicher, Charles W., Jr.↗
NASA NTRS1989

On the origin of pulsed emission from the young supernova remnant SN 1987A

To overcome difficulties in understanding the origin of the sub-msec optical pulses from SN 1987A, a model similar to that of Kundt and Krotscheck (1977) for pulsed synchotron emission from the Crab is applied. The interaction of the expected ultrarelativistic electron-positron pulsar wind with pulsar dipole EM wave or wind-carried toroidal magnetic field reflected from the walls of the expected pulsar cavity within the SN 1987A nebula can generate pulsed optical emission with efficiency at most 0.001. The maximum luminosity of the source is reproduced, and other observational constraints can be satisfied for an average wind energy flow of about 10 to the 38th erg/sec sr and for wind electron Lorentz factor gamma of about 100,000. This model applied to the Crab yields pulsations of much lower luminosity and frequency.

Ruderman, M.↗
NASA NTRS1997

Measurement of Charge Transfer Rate Coefficient Between Ground-State N(2+) Ion and He at Electron-Volt Energies

The charge transfer rate coefficient for the reaction N(2+)(2p(sup 2)P(sup 0)) + He yields products is measured by recording the time dependence of the N(2+) ions stored in an ion trap. A cylindrical radio-frequency ion trap was used to store N(2+) ions produced by laser ablation of a solid titanium nitride target. The decay of the ion signals was analyzed by single exponential least-squares fits to the data. The measured rate coefficient is 8.67(0.76) x 10(exp -11)sq cm/s. The N(2+) ions were at a mean energy of 2.7 eV while He gas was at room temperature, corresponding to an equivalent temperature of 3.9 x 10(exp 3) K. The measured value is in good agreement with a recent calculation.

Fang, Z.↗
NASA NTRS1999

Electrical Impact of SiC Structural Crystal Defects on High Electric Field Devices

Commercial epilayers are known to contain a variety of crystallographic imperfections. including micropipes, closed core screw dislocations. low-angle boundaries, basal plane dislocations, heteropolytypic inclusions, and non-ideal surface features like step bunching and pits. This paper reviews the limited present understanding of the operational impact of various crystal defects on SiC electrical devices. Aside from micropipes and triangular inclusions whose densities have been shrinking towards manageably small values in recent years, many of these defects appear to have little adverse operational and/or yield impact on SiC-based sensors, high-frequency RF, and signal conditioning electronics. However high-power switching devices used in power management and distribution circuits have historically (in silicon experience) demanded the highest material quality for prolonged safe operation, and are thus more susceptible to operational reliability problems that arise from electrical property nonuniformities likely to occur at extended crystal defects. A particular emphasis is placed on the impact of closed-core screw dislocations on high-power switching devices, because these difficult to observe defects are present in densities of thousands per cm,in commercial SiC epilayers. and their reduction to acceptable levels seems the most problematic at the present time.

Neudeck, Philip G.↗
NASA NTRS1994

Application of Coupled-Cluster Methods to the Prediction and Interpretation of the Spectra of Molecules of Interest in Atmospheric Chemistry

The quality of fundamental vibrational frequencies determined using the CCSD(T) method (singles and doubles coupled-cluster theory plus a perturbational estimate of the effects of connected triple excitations) is shown to be very good, usually predicting band centers to within +/-8/cm. This approach is applied to several molecules of interest in atmospheric chemistry, including HNO, NO2(+), H2CO, and HOCl. The HNO molecule displays a large and unusual anharmonicity in the H-N stretch. For the calculation of ultraviolet (UV) spectra, the linear response CCSD (LRCCSD) approach (which is equivalent to EOM-CCSD) has been shown to yield vertical excitation energies that are accurate to approximately 0.1 eV for singly excited electronic states. This method together with more approximate methods is used to examine the UV spectra of several molecules important in stratospheric chemistry, including HOCl, Cl2O, ClOOCl, ClOOH, and HOOH.

Lee, Timothy J.↗
NASA NTRS2006

Record Low NEP in the Hot-Electron Titanium Nanobolometers

We are developing hot-electron superconducting transition-edge sensors (TES) capable of counting THz photons and operating at T = 0.3K. We fabricated superconducting Ti nanosensors with Nb contacts with a volume of approx. 3x10(exp -3) cu microns on planar Si substrate and have measured the thermal conductance due to the weak electron-phonon coupling in the material G = 4x10(exp -14) W/K at 0.3 K. The corresponding phonon-noise NEP = 3x10(exp -19) W/Hz(sup 1/2). Detection of single optical photons (1550nm and 670nm wavelength) has been demonstrated for larger devices and yielded the thermal time constants of 30 microsec at 145 mK and of 25 microsec at 190 mK. This Hot-Electron Direct Detector (HEDD) is expected to have a sufficient energy resolution for detecting individual photons with (nu) > 1 THz where NEP approx. 3x10(exp -20) W/Hz(sup 1/2) is needed for spectroscopy in space.

transition edge sensors↗
NASA NTRS2013

Laboratory Instruments Available to Support Space Station Researchers at Marshall Space Flight Center

A number of research instruments are available at NASA's Marshall Space Flight Center (MSFC) to support ISS researchers and their investigations. These modern analytical tools yield valuable and sometimes new informative resulting from sample characterization. Instruments include modern scanning electron microscopes equipped with field emission guns providing analytical capabilities that include angstron-level image resolution of dry, wet and biological samples. These microscopes are also equipped with silicon drift X-ray detectors (SDD) for fast yet precise analytical mapping of phases, as well as electron back-scattered diffraction (EBSD) units to map grain orientations in crystalline alloys. Sample chambers admit large samples, provide variable pressures for wet samples, and quantitative analysis software to determine phase relations. Advances in solid-state electronics have also facilitated improvements for surface chemical analysis that are successfully employed to analyze metallic materials and alloys, ceramics, slags, and organic polymers. Another analytical capability at MSFC is a mganetic sector Secondary Ion Mass Spectroscopy (SIMS) that quantitatively determines and maps light elements such as hydrogen, lithium, and boron along with their isotopes, identifies and quantifies very low level impurities even at parts per billion (ppb) levels. Still other methods available at MSFC include X-ray photo-electron spectroscopy (XPS) that can determine oxidation states of elements as well as identify polymers and measure film thicknesses on coated materials, Scanning Auger electron spectroscopy (SAM) which combines surface sensitivity, spatial lateral resolution (approximately 20 nm), and depth profiling capabilities to describe elemental compositions in near surface regions and even the chemical state of analyzed atoms. Conventional Transmission Electron Microscope (TEM) for observing internal microstructures at very high magnifications and the Electron Probe Micro-analyzer (EPMA) for very precise microanalysis are available as needed by the researcher. Space Station researchers are invited to work with MSFC in analyzing their samples using these techniques.

Panda, Binayak↗
NASA NTRS2019

An ALMA+ACA measurement of the shock in the Bullet Cluster

Context: The thermal Sunyaev-Zeldovich (SZ) effect presents a relatively new tool for characterizing galaxy cluster merger shocks, traditionally studied through X-ray observations. Widely regarded as the “textbook example” of a cluster merger bow shock, the western, most-prominent shock front in the Bullet Cluster (1E0657-56) represents the ideal test case for such an SZ study. Aims: We aim to characterize the shock properties using deep, high-resolution interferometric SZ effect observations in combination with priors from an independent X-ray analysis. Methods: Our analysis technique relies on the reconstruction of a parametric model for the SZ signal by directly and jointly fitting data from the Atacama Large Millimeter/submillimeter Array (ALMA) and Atacama Compact Array (ACA) in Fourier space. Results: The ALMA+ACA data are primarily sensitive to the electron pressure difference across the shock front. To estimate the shock Mach number M, this difference can be combined with the value for the upstream electron pressure derived from an independent Chandra X-ray analysis. In the case of instantaneous electron-ion temperature equilibration, we find M = 2.08 (+0.12,−0.12), in ≈ 2.4σ tension with the independent constraint from Chandra, M(X)= 2.74 ± 0.25. The assumption of purely adiabatic electron temperature change across the shock leads to M = 2.53 (+0.33,−0.25), in better agreement with the X-ray estimate M(X) = 2.57 ± 0.23 derived for the same heating scenario. Conclusion: We have demonstrated that interferometric observations of the thermal SZ effect provide constraints on the properties of the shock in the Bullet Cluster that are highly complementary to X-ray observations. The combination of X-ray and SZ data yields a powerful probe of the shock properties, capable of measuring M and addressing the question of electron-ion equilibration in cluster shocks. Our analysis is however limited by systematics related to the overall cluster geometry and the complexity of the post-shock gas distribution. To overcome these limitations, a simultaneous, joint-likelihood analysis of SZ and X-ray data is needed.

Luca Di Mascolo↗
NASA NTRS1975

Photomultiplier window materials under electron irradiation - Fluorescence and phosphorescence

The fluorescence and phosphorescence of photomultiplier window materials under electron irradiation have been investigated using a Sr-90/Y-90 beta emitter as the electron source. Spectral emission curves of UV-grade, optical-grade, and electron-irradiated samples of MgF2 and LiF, and of CaF2, BaF2, sapphire, fused silica, and UV-transmitting glasses were obtained over the 200-650-nm spectral range. Fluorescence yields were determined on these materials utilizing photomultiplier tubes with cesium telluride, bialkali, and trialkali (S-20) photocathodes, respectively. Optical-grade MgF2 and LiF, as well as electron-irradiated UV-grade samples of these two materials, show enhanced fluorescence due to color-center formation and associated emission bands in the blue and red wavelength regions. Large variations in fluorescence intensities were found in UV-grade sapphire samples of different origins, particularly in the red end of the spectrum, presumably due to various amounts of chromium-ion content. Phosphorescence decay with time is best described by a sum of exponential terms, with time constants ranging from a few minutes to several days.

Viehmann, W.↗
NASA NTRS1991

The effect of electron collisions on rotational excitation of cometary water

The e-H2O collisional rate for exciting rotational transitions in cometary water is evaluated for conditions found in Comet Halley. The e-H2O collisional rate exceeds that for excitation by neutral-neutral collisions at distances exceeding 3000 km from the cometary nucleus, in the case of the O sub 00 yields 1 sub 11 transition. The estimates are based on theoretical and experimental studies of e-H2O collisions, on ion and electron parameters acquired in-situ by instruments on the Giotto and Vega spacecraft, and on results obtained from models of the cometary ionosphere. The contribution of electron collisions may explain the need for large water-water cross-sections in models which neglect the effect of electrons. The importance of electron collisions is enhanced for populations of water molecules in regions where their rotational lines are optically thick.

Xie, Xingfa↗