SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report provides screenshots of online training on how to use ear loop, tie back, and double elastic face masks made of cloth, surgical, KN95, N95 or homemade materials.
Inelastic scattering reactions including (n,2n) are particularly difficult to measure. Hardly any measurements on radioactive nuclei exist. The reason is that traditional methods require the detection of gammas or neutrons in a background of elastically scattered neutrons, which can interact with the detector or other materials. The 73 As(n,2n) and the 73 As(n,2n) reaction cross sections are the only neutron removal cross sections that can be measured with current methods. The corresponding cross sections for the short-lived isotopes 71,72,74 As can only be directly measured in inverse kinematics. Since 75 As is the only stable isotope of this element, the sample production is no problem at all. This report is therefore focused on the sample production for a possible 73 As(n,2n) campaign.
Gallium oxide (Ga2O3) is an emerging ultra-wide bandgap semiconductor material that has attracted attention for its potential to outperform existing SiC and GaN based devices operating at high breakdown voltages and high temperature. Isovalent alloying of In and Al in Ga2O3 provides the ability to engineer bandgap energy and strain of the material. Alloying with Al increases the bandgap energy and the theoretically achievable Baliga's figure of merit, a key measure of a material's ultimate performance limits for high power switching devices. Alloying with In introduces compressive strain and can be used to counteract the tensile strain of Al incorporation. The resulting (AlxGa1-x-yIny)2O3 alloy can be lattice-matched to commercially available Ga2O3 wafers and has a tunable bandgap energy greater than that of Ga2O3, 4.76 eV. Such lattice-matched material can be grown arbitrarily thick without the detrimental effects of elastic strain and relaxation, making it suitable for high voltage diodes and transistors. However, efforts to synthesize isovalent alloys are complicated by their tendency to phase separate into corundum Al2O3 or bixbyite In2O3. Literature reports of the quaternary (AlxGa1-x-yIny)2O3 are limited to <1% unintentional indium incorporation in In-catalyzed (AlxGa1-x)2O3. The primary limitation to quaternary growth is the limited incorporation of indium at elevated growth temperatures. This limited incorporation is due to both the volatility of indium oxide and Al and Ga cation exchange reactions which replace indium in In2O3. We report on the development of a novel high-throughput molecular beam epitaxy (MBE) technique to screen the growth conditions for the ternary alloy (InyGa1-y)2O3, and the application of these findings to the first successful synthesis of phase pure monoclinic (AlxGa1-x-yIny)2O3 by MBE. By leveraging the unique sub-oxide chemistry of Ga2O3 and in-situ monitoring of crystal properties by reflection high-energy electron diffraction (RHEED), a cyclical growth and etch-back method is developed and applied to rapidly characterize the (InyGa1-y)2O3 growth space. This cyclical method provides approximately 10x increase in experimental throughput and up to 46x improvement in Ga2O3 substrate utilization. Appropriate growth conditions for monoclinic (InyGa1- y)2O3 are identified by machine learning analysis of RHEED patterns and targeted growths are characterized ex-situ to confirm improved In incorporation. These growth conditions are then combined with established (AlxGa1-x)2O3 growth conditions to grow quaternary (AlxGa1-x-yIny)2O3 with Al mole fractions ranging from 1.4% - 24.4% and In mole fractions ranging from 3.1% to 15.5%. The chemical and optical properties of the alloys are investigated by XRD, XPS, and spectroscopic ellipsometry. A lattice-matched (AlxGa1-x-yIny)2O3 alloy is examined by 4D-STEM and the chemical and physical uniformity of Al and In incorporation are discussed.
Significance The origin of spatially heterogeneous alterations in the dynamics of nanoconfined liquids has been a major question in physics, chemistry, and materials science for over 30 y. We combine simulation and theory to establish a unified predictive microscopic understanding in freestanding films at low to medium molecular weight, spanning from thick to ultrathin films. The simulation-based phenomenology of altered dynamics is theoretically predicted and understood based on a combination of coupled near-interface gradients of local caging constraints and interfacial and finite size-induced changes in a collective elastic barrier to motion. No invocation of any realized or incipient critical-like phenomenon is necessary, which may have broad implications for other confined systems and the mechanism of the bulk glass transition.
To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.
Natural kamacite samples (Fe92.5Ni7.5) from a fragment of the Gibeon meteorite were studied as a proxy material for terrestrial cores to examine phase transition kinetics under shock compression for a range of different pressures up to 140 GPa. In situ time-resolved X-ray diffraction (XRD) data were collected of a body-centered cubic (bcc) kamacite section that transforms to the high-pressure hexagonal close-packed (hcp) phase with sub-nanosecond temporal resolution. The coarse-grained crystal of kamacite rapidly transformed to highly oriented crystallites of the hcp phase at maximum compression. The hcp phase persisted for as long as 9.5 ns following shock release. Comparing the c/a ratio with previous static and dynamic work on Fe and Fe-rich Fe-Ni alloys, it was found that some shots exhibit a larger than ideal c/a ratio, up to nearly 1.65. This work represents the first time-resolved laser shock compression structural study of a natural iron meteorite, relevant for understanding the dynamic material properties of metallic planetary bodies during impact events and Earth’s core elasticity.
The emission of white light from a single material is atypical and is of interest for solid-state lighting applications. Broadband light emission has been observed in some layered perovskite derivatives, A 2 PbBr 4 (A = R-NH 3 + ), and correlates with static structural distortions corresponding to out-of-plane tilting of the lead bromide octahedra. While materials with different organic cations can yield distinct out-of-plane tilts, the underlying origin of the octahedral tilting remains poorly understood. Using high energy resolution (e.g., quasi-elastic) neutron scattering, this contribution details the rotational dynamics of the organic cations in A 2 PbBr 4 materials where A = n-butylammonium (nBA), 1,8-diaminooctammonium (ODA), and 4-aminobutyric acid (GABA). The organic cation dynamics differentiate (nBA) 2 PbBr 4 from (ODA)PbBr 4 or (GABA) 2 PbBr 4 in that the larger spatial extent of dynamics of nBA yields a larger effective cation radius. The larger effective volume of the nBA cation in (nBA) 2 PbBr 4 yields a closer to ideal A-site geometry, preventing the out-of-plane tilt and broadband luminescence. In all three compounds, we observe hydrogen dynamics attributed to rotation of the ammonium headgroup and at a time scale faster than the white light photoluminescence studied by time-correlated single photon counting spectroscopy. This supports a previous assignment of the broadband emission as resulting from a single ensemble, such that the emissive excited state experiences many local structures faster than the emissive decay. Furthermore, the findings presented here highlight the role of the organic cation and its dynamics in hybrid organic–inorganic perovskites and white light emission.
Background: Laser cladding offers a promising approach to repairing aviation components, with the ability to restore the geometric shape and the static and fatigue strength. Objective: The damage tolerance of a coarse grain Ti-6Al-4 V material is assessed via three sets of samples: (i) baseline, (ii) laser clad repaired, and (iii) laser cladding followed by heat treatment. Method: The specimens were subjected to fatigue loading using a marker band technique, in which cracks initiated from pre-defined laser slots and the small crack growth rates were measured by quantitative fractography. Additional characterization was performed on these samples, including hardness measurements, microstructure analysis, and multimodal residual stress analyses. Results: The region of the specimen undergoing laser cladding exhibited higher hardness values and a compressive residual stress, based on the slitting method. The samples subjected to heat treatment after cladding displayed negligible differences in grain size and minimal residual stress relaxation. Conclusions: The results demonstrated significant variability, with data demonstrating that cracks in the laser clad region (exhibiting the largest compressive residual stress) grew faster than cracks in the substrate region of the sample or in the baseline cases. Finally, these counterintuitive results are rationalized with additional analyses from synchrotron-based energy dispersive X-ray diffraction and high energy X-ray diffraction, demonstrating significant spatial variability in the residual elastic strains in the millimeter-sized prior β grains within the material.
Nickel-based superalloys with superior thermochemical, mechanical, and tribological properties are highly utilized for critical components in several high temperature applications such as gas turbines and nuclear reactors. Inconel 617, in particular, is considered as one of the main candidate superalloys for tribo-components in very-high-temperature gas-cooled nuclear reactors. Recent findings indicate that this alloy grows unique surface oxide especially in a high-temperature helium environment with distinctive wear, friction, and contact properties. Here, this study investigates the high temperature contact area evolution and frictional behavior of Inconel 617 using finite element simulation and provides predictive models for the contact and friction performance at different normal loads, dwell times, and temperatures. High temperature helium-aged Inconel 617 top surface properties (up to 600 °C) are utilized along with a single asperity-based deformable elastic-plastic contact model under combined normal and tangential loading. Machine learning is used to assist the finite element results and to predict friction coefficient as well as contact area evolution. While a small difference is observed in the instantaneous friction coefficient (no dwell time) for all temperatures, friction coefficient increases considerably with dwell time. This shows that the effect of contact creep for longer dwell times significantly dominants the effect of high temperature variation in basic mechanical parameters such as modulus and yield strength. It is found that increasing temperature and dwell times lead to the friction coefficient increase, yet the dominance of dwell time effects decreases at higher temperatures and loads. While the analysis is presented for Inconel 617, the methodology is easy to be generalized and can be applied to other HT alloys.
Abstract This review examines the characterization and utilization of chestnut processing wastes (35%) in the production of bioplastics and biocomposites. In this review, a Web of Science search without any publishing year restriction on the biochemical compositions of all the components of Castanea sativa . The obtaining of bioplastics and biocomposites based on C. sativa was reviewed. First, it highlights the biochemical composition and antioxidant properties of chestnut fruit, shell, burrs, leaves, flowers, and wood focusing on the most important compounds, such as phenolic acids, flavonoids, carbohydrates, Klason lignin, cellulose, and glucan, which can enhance the properties of these materials. Then the review covers using several chestnut extracts and fillers in bioplastics production through solvent casting technique. The mechanical, structural, bioactive properties, and moisture content were optimized through the composition and production. The color, UV absorption, antioxidant, and antimicrobial activity were also discussed. Biocomposites reinforced with chestnut burs, shells, or wood flour increased the intended properties. The enhancements in tensile strength, elastic modulus, and the effects of a pre‐treatment were evaluated. Additionally, it discusses material recovery, recycling, and reuse, particularly how it affects the biodegradability of composites incorporating chestnut waste residues. Highlights Chestnut fruit, shells, and burrs are rich in starch, lignin, and cellulose. The waste of chestnut processing can be used in bioplastics and biocomposites. Chestnut‐based films and biocomposites exhibit promising mechanical properties. The antimicrobial activity, making films, and composites proper for food packaging. New techniques boost performance, offering alternatives to conventional plastics.
In this study, the elastic properties, structural parameters, sound velocity, and Debye temperature of γ–(U,Zr) were computed using ab initio molecular dynamics (AIMD) at temperatures between 1000 K and 1400 K and for Zr content between 0 at. % and 100 at. %. UZr is used as a metallic fuel for Sodium Fast Reactors (SFRs). The study of the mechanical and thermal behavior of these alloys leads to a better data-informed fuel design. The bulk modulus, shear modulus, Young's modulus, and Poisson's ratio were calculated from the elastic constants and their dependence on Zr content and temperature was investigated, comparing the results with previous computational work and the available experimental data in the literature. Interfacial properties between UZr (up to 32 at. % which typically exists in nuclear fuel) and liquid sodium are also of interest due to the presence of a sodium bond between the fuel and the cladding in metallic nuclear fuel. The interfacial energy between γ–(U,Zr) and liquid sodium, the surface tension of liquid sodium, and the work of adhesion were computed at different temperatures and Zr concentrations. It was demonstrated that γ–(U,Zr) is completely wetted by liquid sodium at all the investigated temperatures and Zr concentrations. Finally, this work provides the basis for the determination of interfacial resistances in SFRs and their implementation into heat transfer fuel performance simulations, which will be the subject of future work.
A combined machine learning–physics–based approach is explored for molecular and materials engineering. Specifically, collective variables, akin to those used in enhanced sampled simulations, are constructed using a machine learning model trained on data gathered from a single system. Through the constructed collective variables, it becomes possible to identify critical molecular interactions in the considered system, the modulation of which enables a systematic tailoring of the system’s free energy landscape. To explore the efficacy of the proposed approach, we use it to engineer allosteric regulation and uniaxial strain fluctuations in a complex disordered elastic network. Its successful application in these two cases provides insights regarding how functionality is governed in systems characterized by extensive connectivity and points to its potential for design of complex molecular systems.
Recent work in metal additive manufacturing (AM) suggests that mechanical properties may vary with feature size; however, these studies do not provide a statistically robust description of this phenomenon, nor do they provide a clear causal mechanism. Because of the huge design freedom afforded by 3D printing, AM parts typically contain a range of feature sizes, with particular interest in smaller features, so the size effect must be well understood in order to make informed design decisions. This work investigates the effect of feature size on the stochastic mechanical performance of laser powder bed fusion tensile specimens. A high-throughput tensile testing method was used to characterize the effect of specimen size on strength, elastic modulus and elongation in a statistically meaningful way. The effective yield strength, ultimate tensile strength and modulus decreased strongly with decreasing specimen size: all three properties were reduced by nearly a factor of two as feature dimensions were scaled down from 6.25 mm to 0.4 mm. Hardness and microstructural observations indicate that this size dependence was not due to an intrinsic change in material properties, but instead the effects of surface roughness on the geometry of the specimens. Finite element analysis using explicit representations of surface topography shows the critical role surface features play in creating stress concentrations that trigger deformation and subsequent fracture. The experimental and finite element results provide the tools needed to make corrections in the design process to more accurately predict the performance of AM components.
Additive friction stir deposition (AFSD) is a rapidly developing solid-state additive manufacturing (AM) technology that enables the fabrication of customized products on a relatively large scale. The unique forge-liked process offers high quality products with refined equiaxed microstructure and exceptional mechanical performance. However, in AFSD, the spatially distributed mechanical properties within a deposited layer have not been established so far, due to the lack of a suitable large-scale mapping method. In the present work, an ultrasonic dynamic-elasticity mapping method was employed to map the distribution of physical properties in a AFSD 6061 Al. Strong spatial asymmetries in elastographies were mainly due to the residual stresses. The origin of the asymmetries was investigated through thermo-mechanical simulations of the AFSD process. It was observed that majority of the asymmetries were associated with the mechanical residual stresses instead of the symmetric thermal residual stresses during linear deposition of the AFSD process. However, the thermal residual stresses can be manipulated to become asymmetric with a 90° turn in the linear deposition path, due to the difference between the levels of cooling along the edges of the inner and outer corners. Hence, the mechanical and thermo-mechanical residual stresses can be additive or subtractive depending on the direction of the turns. Here, such numerically predicted behaviors were also experimentally observed on the AFSD fabricated samples by ultrasonic elastography. Furthermore, additional preliminary studies on multi-layer AFSD fabrications show the asymmetric mechanical stresses generated during the deposition process on different layers generate constructive or destructive interference which results to spatially variable dynamic bulk modulus depending on the deposition orientations of layers.
The segmental dynamics of the side chains of poly(norbornene)- g -poly(propylene oxide) (PNB- g -PPO) bottlebrush polymer in comparison to PPO is studied by quasi-elastic neutron scattering. Having experimental time and length scale information simultaneously allows to extract spatial information in addition to relaxation time. Tethering one end of the PPO side chain onto a stiff PNB backbone slows down the segmental relaxation, over the length and time scales investigated. The power law dependence of the relaxation time on the momentum transfer, Q , indicates a more heterogeneous relaxation pattern for the bottlebrush polymer, whereas the linear PPO has less deviations from a homogenous relaxation. Similar conclusions can be drawn from the time dependent mean square displacement, $\langle$ r 2 ( t )$\rangle$, and the non-Gaussian parameter, α 2 ( t ). Herein, the bottlebrush polymer shows a more restricted dynamics, whereas the linear PPO reaches $\langle$ r 2 ( t )$\rangle$∝ t 0.5 at the highest temperature. The deviations from Gaussian behavior are evident at the α 2 ( t ). Both samples show a decaying α 2 ( t ). Finally, the non-Gaussian parameter supports the results from the power law dependence of the relaxation times, with lower α 2 ( t ) values for PPO compared to those for PNB-g-PPO, pointing to less deviations from Gaussian behavior.
Friction-stir-welding (FSW) has gained importance as an effective way to join dissimilar materials due to its solid-state nature. However, FSW produces substantial residual stresses in aluminum welding, often deteriorating the component's structural performance and reliability. In the current study, the d-spacing (inter-atomic distance) of several locations on a battery tray and stress-free reference samples are measured with neutron diffraction to calculate the residual stresses in a lap 6061 to A365 dissimilar friction-stir-weld. Furthermore, the present study connects the measured residual stress to microstructure properties through electron backscatter diffraction (EBSD) and optical microscopy analyses. The EBSD results indicate that the FSW operation affects the grains’ orientation, thereby producing location-specific directionally varying elasticity across the weldment. Further, this varied elasticity creates unique d-spacing profiles even in the stress-free material. Additionally, the resulting stressed and stress-free d-spacing profiles show dependencies on the FSW tool geometry, traverse direction, and rotational direction. Lastly, this study suggests that the final component residual stress can be influenced by the sequence of multi-pass welds contributing to a rise in temperature in the presence of a completed weld relaxing its residual stress.
The integration of ferroic oxide thin films into advanced flexible electronics will bring multifunctionality beyond organic and metallic materials. However, it is challenging to achieve high flexibility in single-crystalline ferroic oxides that is considerable to organic or metallic materials. Here, we demonstrate the superior flexibility of freestanding single-crystalline BiFeO 3 membranes, which are typical multiferroic materials with multifunctionality. They can endure cyclic 180° folding and have good recoverability, with the maximum bending strain up to 5.42% during in situ bending under scanning electron microscopy, far beyond their bulk counterparts. Such superior elasticity mainly originates from reversible rhombohedral-tetragonal phase transition, as revealed by phase-field simulations. This study suggests a general fundamental mechanism for a variety of ferroic oxides to achieve high flexibility and to work as smart materials in flexible electronics.
In earlier works, a mathematical procedure for invertible microstructure-property linkages was developed using computationally efficient spectral methods for polycrystalline cubic and hexagonal metals. This paper formulates such invertible microstructure–property linkages for orthorhombic polycrystalline metals relying on the generalized spherical harmonics (GSH) spectral basis. The procedure is used to compute property closures of orthorhombic polycrystals. The closures represent the complete set of theoretically possible combinations of effective properties for a selected material. The procedure relies on the first-order bounding theories and considers orientation distribution functions (ODFs) as the main microstructural descriptor influencing homogenized properties. Numerous examples of these closures involving second-rank thermal expansion and fourth-rank elastic stiffness tensorial properties over a broad range of temperatures are presented for α-uranium (α-U). In doing so, certain key properties of these closures are exploited to facilitate their computation with drastically reduced computational effort. Along with the recently developed GSH-based interpolation procedure for ODFs from coarsely spaced experimental measurement grids to finely spaced finite element mesh resolution grids presented in Barrett et al., the developed computationally efficient ODF-effective property linkages are used to establish a crystal mechanics-based simulation framework coupled with the finite element method (FEM). The ODF dependent thermal expansion and elastic stiffness tensors are efficiently calculated at every integration point and used by the FEM to predict the overall distortion of a hemispherical part made of α-U during heating. In conclusion, it is shown that the developed framework can be used to simulate microstructurally heterogeneous components under thermo-mechanical loadings in a computationally efficient manner.