SEARCH · Engineering Papers

Results for “dynamic strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Scaling of impact damage in fiber composites

Impact damage in fiber composite structures remains of much concern, and is often the limiting factor in establishing allowable strain levels. The complexity of impact damage formation usually dictates that experiments are required, but scaling of results from small laboratory scale specimens to large structures introduces additional uncertainty into the analysis. This presentation gives the results of an analytical and experimental investigation intended to develop procedures for prediction of damage formation and subsequent strength loss, with particular emphasis on scaling of results with respect to structure size. The experimental investigation involved both drop-weight and airgun impact on carbon/epoxy plates and cylinders. Five sizes of plates ranging from 50 by 50 by 1.072 mm to 250 by 250 by 5.36 mm, and two sizes of cylinders with diameters of 96.5 and 319 mm, were employed in the experimental program. Impact tests were carried out over a range of impact conditions, and specimens were inspected for damage by C-scan and deplying. Analysis procedures were developed for both quasistatic and dynamic impacts for both the plates and cylinders. As has been reported previously, comparison of predicted structural response and measured surface strains was quite good over the entire range of sizes employed in the program. The damage formation and strength loss after impact showed a number of interesting features that are significant with respect to scaling of size. The extent of delamination was observed to increase with specimen size more than would be expected if stresses controlled the delamination extent. This was explained on the basis that delamination is controlled by energy release rates, and thus incorporates the usual dependence on the absolute size characteristic of fracture mechanics. Additionally, the experiments indicated that delamination initiated at matrix cracks and is dependent on the absolute size of the ply group thicknesses. Both the initiation and propagation of delamination are seen to be controlled by fracture mechanics parameters, and thus show specific dependence on size that must be accounted for in extrapolating results from laboratory scale tests to full size structures.

Swanson, Stephen R.↗

NASA NTRS1982

Crashworthy airframe design concepts: Fabrication and testing

Crashworthy floor concepts applicable to general aviation aircraft metal airframe structures were investigated. Initially several energy absorbing lower fuselage structure concepts were evaluated. Full scale floor sections representative of a twin engine, general aviation airplane lower fuselage structure were designed and fabricated. The floors featured an upper high strength platform with an energy absorbing, crushable structure underneath. Eighteen floors were fabricated that incorporated five different crushable subfloor concepts. The floors were then evaluated through static and dynamic testing. Computer programs NASTRAN and KRASH were used for the static and dynamic analysis of the floor section designs. Two twin engine airplane fuselages were modified to incorporate the most promising crashworthy floor sections for test evaluation.

Cronkhite, J. D.↗

NASA NTRS1982

Strain rate characterization of unidirectional graphite/epoxy composite

For an investigation of problems of composites at high strain rates with dominant wave propagation effects, such as dynamically loaded composite jet engine blades, the longitudinal, transverse, and in-plane shear properties of unidirectional SP 288/AS graphite/epoxy were measured at various strain rates ranging from quasi-static to over 500/s. The test specimens were rings 10.16 cm in diameter, 2.54 cm long, 6 to 8 plies thick, and with fibers at 0, 90, and 10 deg off-axis. Quasi-static testing was conducted in a fixture which applies hydraulic pressure to the ring specimens, and dynamic testing was conducted by applying an internal pressure pulse through a liquid in a special fixture. Dynamic stress-strain curves are presented. For the 0-deg specimens, the modulus increases with strain up to 20 percent of the static value. The modulus and strength increase sharply in the 90-deg rings with strain rate reaching values two to three times the corresponding static rate.

Daniel, I. M.↗

NASA NTRS1984

Phosphorus-containing imide resins - Modification by elastomers

The syntheses and general features of addition-type maleimide resins based on bis(m-aminophenyl)phosphine oxide and tris(m-aminophenyl)phosphine oxide have been reported previously. These resins have been used to fabricate graphite cloth laminates having excellent flame resistance. These composites did not burn even in pure oxygen. However, these resins were somewhat brittle. This paper reports the modification of these phosphorus-containing resins by an amine-terminated butadiene-acrylonitrile copolymer (ATBN) and a perfluoroalkylene diaromatic amine elastomer (3F). An approximately two-fold increase in short beam shear strength and flexural strength was observed at 7 percent ATBN concentration. The tensile, flexural, and shear strengths were reduced when 18 percent ATBN was used. Anaerobic char yields of the resins at 800 C and the limiting oxygen indexes of the laminates decreased with increasing ATBN concentration. The perfluorodiamine (3F) was used with both imide resins at 6.4 percent concentration. The shear strength was doubled in the case of the bisimide with no loss of flammability characteristics. The modified trisimide laminate also had improved properties over the unmodified one. The dynamic mechanical analysis of a four-ply laminate indicated a glass transition temperature above 300 C. Scanning electron micrographs of the ATBN modified imide resins were also recorded.

Varma, I. K.↗

NASA NTRS1989

Spectroscopic study of combustion diagnostics on hydroxyl radicals

Experimental observations of propane/air flames have been carried out. Measurements of hydroxyl (OH) radical concentration have been made using resonance line absorption techniques. A microwave-pumped low pressure discharge in argon and water vapor is employed to produce strong OH radical band radiation in the 308 nm region. This radiation is transmitted through the plume and absorption data is taken at various radial positions using an optical multichannel analyzer. This absorption data is used to compute OH number density using a model for the absorption band characteristics as a function of temperature based on an atlas of line strengths. A numerical computation of flow fields, temperature profile, OH number density and water vapor mass fraction profiles was carried out by using a technique of computational fluid dynamics (CFD). The results of CFD computation are compared with experimental observation with a good agreement.

Eskridge, Richard↗

NASA NTRS2002

A Discrete-Vortex Method for Studying the Wing Rock of Delta Wings

A discrete-vortex method is developed to investigate the wing rock problem associated with highly swept wings. The method uses two logarithmic vortices placed above the wing to represent the vortex flow field and uses boundary conditions based on conical flow, vortex rate of change of momentum, and other considerations to position the vortices and determine their strengths. A relationship based on the time analogy and conical-flow assumptions is used to determine the hysteretic positions of the vortices during roll oscillations. Static and dynamic vortex positions and wing rock amplitudes and frequencies calculated by using the method are generally in good agreement with available experimental data. The results verify that wing rock is caused by hysteretic deflections of the vortices and indicate that the stabilizing moments that limit wing rock amplitudes are the result of the one primary vortex moving outboard of the wing where it has little influence on the wing.

Gainer, Thomas G.↗

NASA NTRS2012

Performance of Reynolds Averaged Navier-Stokes Models in Predicting Separated Flows: Study of the Hump Flow Model Problem

Separation can be seen in most aerodynamic flows, but accurate prediction of separated flows is still a challenging problem for computational fluid dynamics (CFD) tools. The behavior of several Reynolds Averaged Navier-Stokes (RANS) models in predicting the separated ow over a wall-mounted hump is studied. The strengths and weaknesses of the most popular RANS models (Spalart-Allmaras, k-epsilon, k-omega, k-omega-SST) are evaluated using the open source software OpenFOAM. The hump ow modeled in this work has been documented in the 2004 CFD Validation Workshop on Synthetic Jets and Turbulent Separation Control. Only the baseline case is treated; the slot flow control cases are not considered in this paper. Particular attention is given to predicting the size of the recirculation bubble, the position of the reattachment point, and the velocity profiles downstream of the hump.

Cappelli, Daniele↗

NASA NTRS2023

Dynamical Core Damping of Thermal Tides in Martian Atmosphere

Atmospheric oscillations with daily periodicity are observed in in-situ near-surface pressure, temperature, and winds observations, and also in remotely sensed temperature and pressure observations of the Martian atmosphere. Such oscillations are interpreted as thermal tides driven by the diurnal cycle of solar radiation and occur at various frequencies, with the most prominent being the diurnal, semidiurnal, terdiurnal and quadiurnal tides. Mars global circulation models reproduce these tides with varying levels of success. Until recently, both the MarsWRF and newly developed MarsMPAS models were able to produce realistic diurnal and semidiurnal tide amplitudes but predicted higher-order mode amplitudes that were significantly weaker than observed. We use linear wave analysis to show that the divergence damping applied within both MarsWRF and MarsMPAS is responsible for suppressing the amplitude of thermal tides with frequency greater than 2 per sol, despite being designed to suppress only acoustic wave modes. Decreasing the strength of the divergence damping in MarsWRF and MarsMPAS allows for excellent prediction of the higher order tidal modes. This finding demonstrates that care must be taken when applying numerical dampers and filters that may eliminate some desired dynamical features in planetary atmospheres.

Yuan Lian↗

NASA NTRS1956

Interim Report on Fatigue Characteristics of a Typical Metal Wing

Constant amplitude fatigue tests of seventy-two P-51D "Mustang" wings are reported. The tests were performed by a vibrational loading system and by an hydraulic loading device for conditions with and without varying amounts of pre-load. The results indicate that: (a) the frequency of occurrence of fatigue at any one location is related to the range of the loads applied, (b) the rate of propagation of visible cracks is more or less constant for a large portion of the life of the specimen, (c) the fatigue strength of the structure is similar to that of notched material having a theoretical stress concentration factor of more than 3.0, (d) the frequency distribution of fatigue life is approximately logarithmic normal, (e) the relative increase in fatigue life for a given pre-load depends on the maximum load of the loading cycle only, while the optimum pre-load value is approximately 85 percent of the ultimate failing load, and (f) that normal design procedure will not permit the determination of local stress levels with sufficient accuracy to determine the fatigue strength of an element of a redundant structure.

LOADS AND STRESSES, STRUCTURAL - REPEATED DYNAMIC↗

NASA NTRS1975

Design of a graphite/epoxy metering truss for the Large Space Telescope

This paper presents the design development of a truss-type structure which utilizes graphite/epoxy as the primary material system. A review is given of an on-going NASA sponsored program to develop a structural assembly which is required to have a very high degree of dimensional stability. Methods of material characterization and selection are given along with property data such as strength, stiffness, outgassing and thermal expansion. Finite element (NASTRAN) analysis will be discussed and deflection plots of the lowest mode frequencies will be presented. Proposed full scale tests: static, dynamic, and thermal/vacuum will be described.

Oken, S.↗

NASA NTRS1981

Determination of load sequence effects on the degradation and failure of composite materials

A theoretical model was established to predict the fatigue behavior of composite materials, with emphasis placed on predictions of the degradation of residual strength and residual stiffness during fatigue cycling. The model parameters were evaluated from three test series including static strength fatigue life and residual strength tests. The tests were applied to two graphite/epoxy laminates. Load sequence effects were emphasized for both laminates and the predicted results agreed quite well with subsequent verification tests. Dynamic as well as static stiffness reduction data were collected by use of a PDP11-03 computer, which performed quite satisfactorily and permitted the recording of a substantial amount of dynamic stiffness reduction data.

Yang, J. N.↗

NASA NTRS1995

A case and statistical study of transient magnetic field events at geosynchronous orbit and their solar wind origin

We present a statisical survey of Prognoz 10 solar wind observations at the times of transient (step function and impulsive) variations in the dayside magnetospheric magnetic field strength measured by the GOES 5 and 6 geosynchronous satellites. The results indicate that 51% of the magnetospheric events can be associated with corresponding variations in the solar wind dynamic pressure. A further 17% of the events can be associated with fluctuations in the interplanetary magnetic field orientation in the sense previously associated with foreshock pressure pulses. We find no tendency for impulsive events at dayside geosynchronous orbit to be associated with north/south fluctuations in the interplanetary magnetic field (IMF) orientation, nor for the events to occur primarily during intervals of southward IMF. The success rate for associating transient events at dayside geosynchronous orbit with solar wind features decreases as Prognoz 10 moves farther from the Earth-Sun line. The observations indicate that variations in the solar wind dynamic pressure and foreshock pressure pulses associated with variations in the IMF cone angle are the predominant causes of large-amplitude transient events observed at dayside geosynchronous orbit.

Borodkova, N. L.↗

NASA NTRS1997

Magnetospheric Plasmas-Flow and Energization of the Ionospheric Source

In a paper of more than a decade ago, estimated the strength of the ionospheric source and its ability to supply the different plasma regions of the Earth's magnetosphere. The launch of the POLAR spacecraft with the Thermal Ion Dynamics Experiment (TIDE) and the active control of spacecraft potential thro6gh the Plasma Source Instrument (PSI) made possible for the first time the direct measurement of low energy ions moving from the ionosphere into the lobes of the magnetotail. A particle trajectory model has been used to trace particles representative 6f TIDE measurements, taken during the operation of PSI, back to the location of the ionospheric source and forward to the entry point of the ions to the plasma sheet.

Chappell, C. R.↗

NASA NTRS2000

Magnetically Actuated Propellant Orientation Experiment, Controlling Fluid Motion With Magnetic Fields in a Low-Gravity Environment

This report details the results of a series of fluid motion experiments to investigate the use of magnets to orient fluids in a low-gravity environment. The fluid of interest for this project was liquid oxygen (LO2) since it exhibits a paramagnetic behavior (is attracted to magnetic fields). However, due to safety and handling concerns, a water-based ferromagnetic mixture (produced by Ferrofluidics Corporation) was selected to simplify procedures. Three ferromagnetic fluid mixture strengths and a nonmagnetic water baseline were tested using three different initial fluid positions with respect to the magnet. Experiment accelerometer data were used with a modified computational fluid dynamics code termed CFX-4 (by AEA Technologies) to predict fluid motion. These predictions compared favorably with experiment video data, verifying the code's ability to predict fluid motion with and without magnetic influences. Additional predictions were generated for LO2 with the same test conditions and geometries used in the testing. Test hardware consisted of a cylindrical Plexiglas tank (6-in. bore with 10-in. length), a 6,000-G rare Earth magnet (10-in. ring), three-axis accelerometer package, and a video recorder system. All tests were conducted aboard the NASA Reduced-Gravity Workshop, a KC-135A aircraft.

Martin, J. J.↗

NASA NTRS2002

Static and Dynamic Effects of Lateral Carrier Diffusion in Semiconductor Lasers

Electron and hole diffusions in the plane of semiconductor quantum wells play an important part in the static and dynamic operations of semiconductor lasers. It is well known that the value of diffusion coefficients affects the threshold pumping current of a semiconductor laser. At the same time, the strength of carrier diffusion process is expected to affect the modulation bandwidth of an AC-modulated laser. It is important not only to investigate the combined DC and AC effects due to carrier diffusion, but also to separate the AC effects from that of the combined effects in order to provide design insights for high speed modulation. In this presentation, we apply a hydrodynamic model developed by the present authors recently from the semiconductor Bloch equations. The model allows microscopic calculation of the lateral carrier diffusion coefficient, which is a nonlinear function of the carrier density and plasma temperature. We first studied combined AC and DC effects of lateral carrier diffusion by studying the bandwidth dependence on diffusion coefficient at a given DC current under small signal modulation. The results show an increase of modulation bandwidth with decrease in the diffusion coefficient. We simultaneously studied the effects of nonlinearity in the diffusion coefficient. To clearly identify how much of the bandwidth increase is a result of decrease in the threshold pumping current for smaller diffusion coefficient, thus an effective increase of DC pumping, we study the bandwidth dependence on diffusion coefficient at a given relative pumping. A detailed comparison of the two cases will be presented.

Li, Jian-Zhong↗

NASA NTRS2017

Meteoroid Bulk Density and Ceplecha Types

Determination of asteroid bulk density is an important aspect of NEO characterization, yet difficult to measure. As a fraction of meteoroids originate from asteroids (including some NEOs), a study of meteoroid bulk densities can potentially provide useful insights into the densities of NEOs and PHOs in lieu of mutual perturbations, satellite, or expensive spacecraft missions. NASA's Meteoroid Environment Office characterizes the meteoroid environment for the purpose of spacecraft risk and operations. To accurately determine the risk, a distribution of meteoroid bulk densities are needed. This is not trivial to determine. If the particle survives to the ground the bulk density can be directly measured, however only the most dense particles land on the Earth. The next best approach is to model the meteor's ablation, which is not straightforward. Clear deceleration is necessary to do this and there are discrepancies in results between models. One approach to a distribution of bulk density is to use a measured proxy for the densities, then calibrate the proxy with known densities from meteorite falls, ablation modelling, and other sources. An obvious proxy choice is the Ceplecha type, K(sub B), thought to indicate the strength of a meteoroid. KB is frequented cited as a good proxy for meteoroid densities, but we find it is poorly correlated with density. However, a distinct split by dynamical type was seen with Jovian Tisserand parameter, T(sub J), with meteoroids from Halley Type comets (T(sub J less than 2 ) exhibiting much lower densities than those originating from Jupiter and asteroids (T(sub J greater than 2).

Blaauw, R. C.↗

NASA NTRSDate not supplied

Lunar Laser Ranging in the Artemis Era

The retroreflector arrays placed on the lunar surface by the Apollo astronauts and the Soviet Luna missions continue to contribute to our understanding of gravitational physics, Earth and Moon geophysics, geodesy, and dynamics. The key science questions addressed by Lunar Laser Ranging remain very relevant today: What is the interior structure of the Moon? Is the Equivalence Principle exact? Does the strength of gravity vary with space and time? What is the nature of spacetime? Do extra dimensions or other new physics alter the inverse square law of gravity? The lunar retroreflectors are also an essential component of the realizations of the lunar reference frames. The half-century old lunar retroreflectors continue to provide excellent ranging targets but are showing signs of degradation and the measurement error associated with their physical size and varying tilt is becoming a limitation in the quest for more precise range measurements. In addition, the clustering of the arrays in the mid-latitudes of the Moon limits their geometrical strength and coverage. The south polar region planned for Artemis presents an ideal opportunity for improving the geometric distribution. Retroreflectors utilizing a large optical cross-section single cube corner do not have tilt error associated with the existing arrays making them good options for lunar deployment. Several new retroreflectors of this type are being prepared for upcoming Commercial Lunar Payload Services missions as well as Artemis. This presentation will discuss NASA’s plans for expanding the lunar laser ranging capabilities with a focus on the Artemis Lunar Laser Retroreflector.

Stephen Merkowitz↗

NASA NTRS1998

Electromagnetics and Fluid Dynamics

Previous efforts focused on developing tools for design of low observables were sustained. The final product was the maturation of a high-order accurate finite-volume based code to solve Maxwell's equations. One of the primary achievements was the development and implementation of efficient filtering techniques which enhance the robustness of high-order and optimized schemes without significant adverse impact on accuracy. This has eliminated the stability barrier which restrains the common use of high-order schemes for conservative wave propagation phenomena on curvilinear meshes. A study was performed of crossing shock interactions under conditions of increasing interaction strength and asymmetry. In the first category, the observed computed topological bifurcations were correlated with the formation of various lines of coalescence and divergence evident in experimental and computed surf-ace oil maps. ne flow structure arising from asymmetric interactions was investigated with particular emphasis on: 1) vorticity dynamics, 2) shock-structure and 3) sidewall vortex loading. Several efforts of the prior year were successfully published in archival journals. The high-order algorithms developed for CEM have been implemented into the FDL3DI CFD code are presently undergoing extensive testing. Preliminary results are highly encouraging.

Gaitonde, Datta↗