Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Cross-linked polyvinyl alcohol films as alkaline battery separators

Cross-linking methods have been investigated to determine their effect on the performance of polyvinyl alcohol (PVA) films as alkaline battery separators. The following types of cross-linked PVA films are discussed: (1) PVA-dialdehyde blends post-treated with an acid or acid periodate solution (two-step method) and (2) PVA-dialdehyde blends cross-linked during film formation (drying) by using a reagent with both aldehyde and acid functionality (one-step method). Laboratory samples of each cross-linked type of film were prepared and evaluated in standard separator screening tests. Then pilot-plant batches of films were prepared and compared to measure differences due to the cross-linking method. The pilot-plant materials were then tested in nickel oxide-zinc cells to compare the two methods with respect to performance characteristics and cycle life. Cell test results are compared with those from tests with Celgard.

Sheibley, D. W.↗

A burnup credit approach for margin estimation of loaded boiling water reactor canisters in UNF-ST-DARDS

This paper discusses the modeling approach applied in the Used Nuclear Fuel Storage, Transportation, and Disposal Analysis Resource and Data System (UNF-ST-DARDS) to take credit for the reduced reactivity associated with the burnup of boiling water reactor (BWR) fuel for canister-specific as-loaded criticality analysis. Burnup credit is routinely used for the analysis of pressurized water reactor (PWR) spent nuclear fuel (SNF) storage (wet), transportation, and disposal. The fresh fuel assumption has historically been applied to BWR SNF criticality analyses for dry storage and transportation, and the peak reactivity method of burnup credit has been applied to pool storage. The fresh fuel assumption ignores the credit for gadolinium burnable absorbers in BWR fuel, as well as the burnup of the fuel, and is therefore conservative. This work employs the framework traditionally used for PWR burnup credit analyses and applies available data and recently published regulatory guidance to justify a new approach to model the as-loaded burnup and enrichment of SNF assemblies in currently loaded dry casks. The following features of this criticality analysis approach are presented in this paper: (1- selection of axial burnup profiles for BWR fuel from publicly available sources using methods derived from recently published research, (2- justification of the selected axial burnup profiles as relevant to all types of BWR fuel, (3- justification for modeling the fuel assemblies with a uniform axial and radial enrichment, and (4- justification for modeling the axial void profile and control blade insertion during depletion. This analysis approach was used to evaluate 153 already-loaded BWR casks at 8 sites as a function of time in UNF-ST-DARDS. Finally, the results of the as-loaded criticality safety margin assessments are presented. The results show the k{sub eff} calculated for storage and transportation cases range from 0.71 to 0.83, and the eigenvalues calculated for the disposal cases range from 0.85 to 1.03, though the highest cases are dominated by very limiting hypothetical damaged fuel assumptions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Dry Saliva Development-Artemis

Prior to the deployment of prolonged deep space missions which may carry increased crew health risks, it is essential to determine the effect that missions beyond the Van Allen Belt will have on physiology. Historically the National Aeronautics and Space Administration (NASA), Human Research Program (HRP) has developed, conducted, and delivered research findings and countermeasures that will maintain the health and safety of crews aboard the International Space Station (ISS) in anticipation of future exploration class missions. To support these objectives, research operations on ISS typically include the collection and storage of human physiological samples and their return to Earth for analysis. Transition to Gateway and Artemis lunar exploration will limit the available up mass and biosample return capability resulting in new challenges to monitor crew health during the mission. The Artemis lunar missions provide a perfect opportunity to assess new technology that could support crew biosample return that is compatible with the severe operational constraints of Artemis mission design. Dried biosample chemistry analysis is a potential technology that can enable the collection of samples and tracking of crew health during these exploration class missions. The development and implementation of dried biosample chemistry technology for tracking immune health, viral reactivation and hormone fluctuations provide a simple alternative strategy for sample collection and sample return (light weight non-conditioned stowage option) for the continuation of human research during Artemis missions. Saliva is established as an informative biosample that has both its own unique available analytes as well as others that are also present in blood. Saliva is already routinely collected from ISS astronauts for the detection of stress hormones and latent virus DNA. The ‘Dry Saliva’ book sample collection/storage protocol, already successfully deployed to ISS, represents a perfect method for collecting biosamples from Gateway and Artemis astronauts because it requires a simple, non-invasive sample collection protocol, minimum volume, and uses non-conditioned storage. We are currently conducting an expanded stability study of the dry saliva analyte platform to include additional stress hormones, cytokines, antimicrobial proteins, and latent virus DNA as well as other markers of immunity and inflammation. Validation testing on parabolic flight will establish collection methods for saliva and blood to dry sampling substrates to finalize the collection protocols for flight. For the new expanded analyte stability study, a short-term stability study with time points out to 14 days has been completed with analysis underway to determine whether additional analytes could be recovered, as well as assessing the best storage conditions for the samples collected. In parallel, a long-term stability study is being conducted out to 1 year to improve the stability of some unstable analytes. To this end, the NASA Johnson Space Center’s Immunology/Virology lab is currently finalizing the saliva dry chemistry platform, including assay compatibility and stability studies. This technology is approved to be implemented, as part of the ‘Biomarkers’ study, during Artemis II through Artemis IV lunar missions.

Mayra Nelman-Gonzalez↗

Remote sensing techniques for prediction of watershed runoff

Hydrologic parameters of watersheds for use in mathematical models and as design criteria for flood detention structures are sometimes difficult to quantify using conventional measuring systems. The advent of remote sensing devices developed in the past decade offers the possibility that watershed characteristics such as vegetative cover, soils, soil moisture, etc., may be quantified rapidly and economically. Experiments with visible and near infrared data from the LANDSAT-1 multispectral scanner indicate a simple technique for calibration of runoff equation coefficients is feasible. The technique was tested on 10 watersheds in the Chickasha area and test results show more accurate runoff coefficients were obtained than with conventional methods. The technique worked equally as well using a dry fall scene. The runoff equation coefficients were then predicted for 22 subwatersheds with flood detention structures. Predicted values were again more accurate than coefficients produced by conventional methods.

Blanchard, B. J.↗

A Burnup Credit Approach for Margin Estimation of Loaded Boiling Water Reactor Canisters in UNF-ST&DARDS

This paper discusses the modeling approach applied in the Used Nuclear Fuel Storage, Transportation, & Disposal Analysis Resource and Data System (UNF-ST&DARDS) to take credit for the reduced reactivity associated with the burnup of boiling water reactor (BWR) fuel for canister-specific as loaded criticality analysis. Burnup credit is routinely used for the analysis of pressurized water reactor (PWR) spent nuclear fuel (SNF) storage (wet), transportation, and disposal. The fresh fuel assumption has historically been applied to BWR SNF criticality analyses for dry storage and transportation, and the peak reactivity method of burnup credit has been applied to pool storage. The fresh fuel assumption ignores the credit for gadolinium burnable absorbers in BWR fuel, as well as the burnup of the fuel, and is therefore conservative. This work employs the framework traditionally used for PWR burnup credit analyses and applies available data and recently published regulatory guidance to justify a new approach to model the as-loaded burnup and enrichment of SNF assemblies in currently loaded dry casks. The following features of this criticality analysis approach are presented in this paper: (1) selection of axial burnup profiles for BWR fuel from publicly available sources using methods derived from recently published research, (2) justification of the selected axial burnup profiles as relevant to all types of BWR fuel, (3) justification for modeling the fuel assemblies with a uniform axial and radial enrichment, and (4) justification for modeling the axial void profile and control blade insertion during depletion. This analysis approach was used to evaluate 153 already-loaded BWR casks at 8 sites as a function of time in UNF ST&DARDS. Finally, the results of the as-loaded criticality safety margin assessments are presented. The results show the k eff calculated for storage and transportation cases range from 0.71 to 0.83, and the eigenvalues calculated for the disposal cases range from 0.85 to 1.03, though the highest cases are dominated by very limiting hypothetical damaged fuel assumptions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Drying/self-assembly of nanoparticle suspensions.

The most feasible way to disperse particles in a bulk material or control their packing at a substrate is through fluidization in a carrier that can be processed with well-known techniques such as spin, drip and spray coating, fiber drawing, and casting. The next stage in the processing is often solidification involving drying by solvent evaporation. While there has been significant progress in the past few years in developing discrete element numerical methods to model dense nanoparticle dispersion/suspension rheology which properly treat the hydrodynamic interactions of the solvent, these methods cannot at present account for the volume reduction of the suspension due to solvent evaporation. As part of LDRD project FY-101285 we have developed and implemented methods in the current suite of discrete element methods to remove solvent particles and volume, and hence solvent mass from the liquid/vapor interface of a suspension to account for volume reduction (solvent drying) effects. To validate the methods large scale molecular dynamics simulations have been carried out to follow the evaporation process at the microscopic scale.

36 MATERIALS SCIENCE↗

Techno-economic analysis of producing solid biofuels and biochar from forest residues using portable systems

Wildfires are becoming extreme and more frequent because of increased fuel loads in the forest and extended dry conditions. Prevention of wildfire by fuel treatment methods will generate forest residues in large volumes, which in addition to available logging residues, can be used to produce biofuels and bioproducts. In this study, the techno-economic assessment of three portable systems to produce woodchips briquettes (WCB), torrefied-woodchips briquettes (TWCB) and biochar from forest residues were evaluated using pilot-scale experimental data. A discounted cash flow rate of return method was used to estimate minimum selling prices (MSPs) for each product, to conduct sensitivity analyses, and to identify potential cost-reduction strategies. Using a before-finance-and-tax 16.5% nominal required return on investment, and a mean transport distance of 200 km, the estimated delivered MSPs per oven-dry metric ton (ODMT) of WCB, TWCB, and biochar were $162, $274, and $1044 respectively. The capital investment (16–30%), labor cost (23–28%), and feedstock cost (10–13%) without stumpage cost were the major factors influencing the MSP of solid biofuels and biochar. However, the MSPs of WCB, TWCB, and biochar could be reduced to $65, $145, and $470/ODMT respectively with technologically improved portable systems. In addition, the MSPs of solid biofuels and biochar could be further reduced by renewable energy and carbon credits, if the greenhouse gas (GHG) reduction potentials are quantified and remunerated. In conclusion, portable systems could be economically feasible to use forest residues and make useful products at current market prices while simultaneously reducing potential wildfires and GHG emissions.

09 BIOMASS FUELS↗

Towards local progression estimation of pulmonary emphysema using CT

Purpose: Whole lung densitometry on chest CT images is an accepted method for measuring tissue destruction in patients with pulmonary emphysema in clinical trials. Progression measurement is required for evaluation of change in health condition and the effect of drug treatment. Information about the location of emphysema progression within the lung may be important for the correct interpretation of drug efficacy, or for determining a treatment plan. The purpose of this study is therefore to develop and validate methods that enable the local measurement of lung density changes, which requires proper modeling of the effect of respiration on density. Methods: Four methods, all based on registration of baseline and follow-up chest CT scans, are compared. The first naïve method subtracts registered images. The second employs the so-called dry sponge model, where volume correction is performed using the determinant of the Jacobian of the transformation. The third and the fourth introduce a novel adaptation of the dry sponge model that circumvents its constant-mass assumption, which is shown to be invalid. The latter two methods require a third CT scan at a different inspiration level to estimate the patient-specific density-volume slope, where one method employs a global and the other a local slope. The methods were validated on CT scans of a phantom mimicking the lung, where mass and volume could be controlled. In addition, validation was performed on data of 21 patients with pulmonary emphysema. Results: The image registration method was optimized leaving a registration error below half the slice increment (median 1.0 mm). The phantom study showed that the locally adapted slope model most accurately measured local progression. The systematic error in estimating progression, as measured on the phantom data, was below 2 gr/l for a 70 ml (6%) volume difference, and 5 gr/l for a 210 ml (19%) difference, if volume correction was applied. On the patient data an underlying linearity assumption relating lung volume change with density change was shown to hold (fitR{sup 2} = 0.94), and globalized versions of the local models are consistent with global results (R{sup 2} of 0.865 and 0.882 for the two adapted slope models, respectively). Conclusions: In conclusion, image matching and subsequent analysis of differences according to the proposed lung models (i) has good local registration accuracy on patient data, (ii) effectively eliminates a dependency on inspiration level at acquisition time, (iii) accurately predicts progression in phantom data, and (iv) is reasonably consistent with global results in patient data. It is therefore a potential future tool for assessing local emphysema progression in drug evaluation trials and in clinical practice.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

A method for evaluating bias in global measurements of CO 2 total columns from space

We describe a method of evaluating systematic errors in measurements of total column dry-air mole fractions of CO{sub 2} (X{sub CO{sub 2}} ) from space, and we illustrate the method by applying it to the Atmospheric CO{sub 2} Observations from Space retrievals of the Greenhouse Gases Observing Satellite (ACOS-GOSAT) v2.8. The approach exploits the lack of large gradients in X{sub CO{sub 2}} south of 25{degree} S to identify large-scale offsets and other biases in the ACOS-GOSAT data with several retrieval parameters and errors in instrument calibration. We demonstrate the effectiveness of the method by comparing the ACOS-GOSAT data in the Northern Hemisphere with ground truth provided by the Total Carbon Column Observing Network (TCCON). We use the correlation between free-tropospheric temperature and X{sub CO{sub 2}} in the Northern Hemisphere to define a dynamically informed coincidence criterion between the ground-based TCCON measurements and the ACOS-GOSAT measurements. We illustrate that this approach provides larger sample sizes, hence giving a more robust comparison than one that simply uses time, latitude and longitude criteria. Our results show that the agreement with the TCCON data improves after accounting for the systematic errors. A preliminary evaluation of the improved v2.9 ACOS-GOSAT data is also discussed.

54 ENVIRONMENTAL SCIENCES↗

Techno-economic analysis of jet-fuel production from biorefinery waste lignin

Utilizing lignin feedstock along with cellulosic ethanol for the production of high-energy-density jet fuel offers a significant opportunity to enhance the overall operation efficiency, carbon conversion efficiency, economic viability, and sustainability of biofuel and chemical production. A patented catalytic process to produce lignin-substructure-based hydrocarbons in the jet-fuel range from lignin was developed. Comprehensive techno-economic analysis of this process was conducted through process simulation in this study. The discounted cash flow rate of return (DCFROR) method was used to evaluate a 2000 dry metric ton/day lignocellulosic ethanol biorefinery with the co-production of lignin jet fuel. The minimum selling price of lignin jet fuel at a 10% discount rate was estimated to be in the range of $6.35-$1.76/gal depending on the lignin and conversion rate and capacity. With a production capacity of 1.5-16.6 million gallon jet fuel per year, capital costs ranged from $38.0 to $39.4 million. On the whole, the co-production of jet fuel from lignin improved the overall economic viability of an integrated biorefinery process for corn ethanol production by raising co-product revenue from jet fuels.

09 BIOMASS FUELS↗

Structural and morphological characterization of Mg{sub 0.8}Al{sub 0.2}(OH){sub 2}Cl{sub 0.2} hydrotalcite produced by mechanochemistry method

Chlorine intercalated Mg–Al layered double hydroxides (Mg–Al–Cl–LDH) with a chemical formula Mg{sub 0.8}Al{sub 0.2}(OH){sub 2}Cl{sub 0.2} were successfully produced by the one-step mechanochemistry method and subsequent water washing followed by drying in oven for 1 h at 80 °C. The samples were characterized by X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FT–IR), field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), elemental mapping analysis, transmission electron microscopy (TEM), X-ray fluorescence (XRF), and the differential thermogravimetric analysis (DTGA). Results revealed that the structural characteristics of Mg–Al–Cl–LDH were affected strongly by milling time. At the beginning of milling (up to 1 h), Hydrotalcite (HT) and Brucite were the dominant phases, while the progressive mechanical activation was completed as milling time increased, which resulted in the formation of nanostructured Mg–Al–Cl–LDH. Based on XRD and FTIR data, Mg{sub 0.8}Al{sub 0.2}(OH){sub 2}Cl{sub 0.2} with high purity was obtained at 5 h milling. The interlayer spacing of LDH is also strongly influenced by milling time so that it escalated from 7.737±0.001 to 8.005±0.002 (1–15 h) and then decreased to 7.937±0.001 for 20 h milled sample. Electron microscopic observation displayed that the final product had hexagonal platelet structure with lateral dimension of 20–100 nm. Therefore, the synthesis of Mg{sub 0.8}Al{sub 0.2}(OH){sub 2}Cl{sub 0.2} via mechanochemistry owing to simplicity and versatility can be a promising candidate for use in catalyst carriers, drug delivery, and gene delivery. - Graphical Abstract: TEM image of milled sample (Mg–Al–Cl–LDH). - Highlights: • Chlorine intercalated LDH was synthesized by a facile solid-state process. • Structural features of products were influenced strongly by the milling time. • XRD and FTIR spectra suggested predominant Mg–Al–Cl–LDH after 5 h milling. • Products showed hexagonal platelet structure with lateral dimension of 20–100 nm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Force reduction of friction stir welding and processing of steel

Friction stir welding and processing (FSW&P) is considered as a new fabrication method for canisters and repair of existing dry cask storage system canisters (generally made of austenitic stainless steel). Low heat input compared to fusion joining processes and grain refinement associated with low-temperature FSW&P result in a material with improved mechanical properties and equivalent generalized corrosion performance relative to the base metal. But FSW&P of austenitic stainless steel requires significant tool forge axis force to produce a weld (or a run). Exploratory runs utilizing forge axis force control were conducted to investigate the minimum force required to achieve defect-free runs. The correlation between forge axis force and resultant plunge depth was also investigated. Furthermore, detailed microstructural characterization was conducted to display the microstructural variation within the nugget zone.

36 MATERIALS SCIENCE↗

Analysis of the Amorphous and Interphase Influence of Comononomer Loading on Polymer Properties toward Forwarding Bioadvantaged Copolyamides

In this paper we present an approach for selectively modifying the properties of semicrystalline polymers by introducing “bioadvantaged” counits. With this approach, the unique functionality of biomass can be leveraged to tailor the properties of the amorphous phase of semicrystalline polymers with minimal impact on crystallinity and thermomechanical properties. As a model case, PA 6,6 copolyamides were produced using the bioadvantaged monomer trans-3-hexenedioic acid (t3HDA). The analogous structure of t3HDA to adipic acid, a PA 6,6 monomer, allows for seamless integration. Screening over the entire composition range identified the t3HDA loading (20 mol%) beyond which properties deviate appreciably from Nylon 6,6. Once identified, copolyamides of suitable compositions were upgraded to commercial quality and fully characterized to assess the influence of counit loading and polymer structure on thermal and mechanical properties. Samples were characterized using gel permeation chromatography (GPC), proton nuclear magnetic resonance spectroscopy (1H NMR), heteronuclear single quantum coherence spectroscopy (HSQC), wide-angle X-ray scattering (WAXS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), tensile testing, flexural testing, and water absorption testing. t3HDA units were shown to hydrate during the harsh polycondensation to 3-hydroxyhexanedioic acid (3HHDA) and fully incorporate into the polymer backbone. Loading levels up to 20% were shown to have comparable thermal and mechanical properties in the dry state, yet moisture absorption—a known method for improving the toughness, yield strain, and elongation of polyamides—was enhanced by over 100% at 20% loading. This case study on bioadvantaged copolymers elucidates the governing structure-function principles that can be leveraged to forward value-added renewable polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improving the structural quality and electrical resistance of SrTiO{sub 3} thin films on Si (001) via a two-step anneal

We report on the optimization of structural and electrical properties of SrTiO{sub 3} thin films grown on Si (001) by hybrid molecular beam epitaxy. Using a dual buffer layer template, 46-nm-thick films grown at high temperatures (850 °C) resulted in a layer-by-layer growth mode and a good crystalline quality with rocking curve full width at half maximum (FWHM) of the 002 SrTiO{sub 3} peak of nearly 0.6°, which was reduced to 0.4° by increasing the film thickness to 120 nm. A high temperature post-deposition anneal was employed to further reduce the rocking curve FWHM down to 0.2° while preserving a smooth film surface morphology. The low sheet resistance of as-grown and post-growth annealed samples was increased by five orders of magnitude exceeding 10{sup 7} Ω/◻ using a lower temperature anneal in dry air. This two-step annealing method provides an easy and effective way to improve the crystalline quality of SrTiO{sub 3} thin films on Si, providing a path towards the development of electrically insulating, wafer scale virtual perovskite substrates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Study of calcium-containing orthophosphates of NaZr{sub 2}(PO{sub 4}){sub 3} structural type by high-temperature X-ray diffraction

Orthophosphates Ca{sub 0.5}Ti{sub 2}(PO{sub 4}){sub 3}, Ca{sub 0.5}Zr{sub 2}(PO{sub 4}){sub 3}, Ca{sub 0.75}Zr{sub 2}(SiO{sub 4}){sub 0.5}(PO{sub 4}){sub 2.5}, and CaMg{sub 0.5}Zr{sub 1.5}(PO{sub 4}){sub 3} (structural type NaZr{sub 2}(PO{sub 4}){sub 3}), having different occupancies of interframework positions by calcium, have been prepared by the sol-gel method with the subsequent thermal treatment of dried gels and investigated by IR spectroscopy and X-ray diffraction. The analytical indexing of X-ray diffraction patterns is performed within the sp. gr. R3{sup -}. High-temperature X-ray diffraction was used to investigate the behavior of the orthophosphates upon heating: thermal expansion in the temperature range of 20-610 Degree-Sign C (up to 500 Degree-Sign C for Ca{sub 0.5}Zr{sub 2}(PO{sub 4}){sub 3}). The coefficients of thermal expansion are calculated from the shift of diffraction peaks. The unit-cell parameters of crystals at different temperatures are determined. The dependences of thermal expansion and its anisotropy on the occupancy of cation M positions by calcium are revealed.

36 MATERIALS SCIENCE↗

Direct electron beam patterning of electro-optically active PEDOT:PSS

The optical and electronic tunability of the conductive polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has enabled emerging applications as diverse as bioelectronics, flexible electronics, and micro- and nano-photonics. High-resolution spatial patterning of PEDOT:PSS opens up opportunities for novel active devices in a range of fields. However, typical lithographic processes require tedious indirect patterning and dry etch processes, while solution-processing methods such as ink-jet printing have limited spatial resolution. Here, we report a method for direct write nano-patterning of commercially available PEDOT:PSS through electron-beam induced solubility modulation. The written structures are water stable and maintain the conductivity as well as electrochemical and optical properties of PEDOT:PSS, highlighting the broad utility of our method. We demonstrate the potential of our strategy by preparing prototypical nano-wire structures with feature sizes down to 250 nm, an order of magnitude finer than previously reported direct write methods, opening the possibility of writing chip-scale microelectronic and optical devices. We finally use the high-resolution writing capabilities to fabricate electrically-switchable optical diffraction gratings. We show active switching in this archetypal system with >95 % contrast at CMOS-compatible voltages of +2 V and -3 V, offering a route towards highly-miniaturized dynamic optoelectronic devices.

42 ENGINEERING↗

Vapor-Processing of Metal-Halide Perovskites for Photovoltaics and Optoelectronics

Metal-halide perovskites are an exciting materials platform for next generation optoelectronic devices and solar cells. In this presentation, we review our work in processing metal-halide perovskites via a dry, carrier-gas assisted vapor deposition method, and its ability to be useful for the formation of all-perovskite heterojunctions. We also outline recent work demonstrating the viability of this method for the deposition of lead-based perovskites via co-deposition.

14 SOLAR ENERGY↗