Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drag”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Variation of the drag coefficient and its dependence on sea state

Using a Gill propeller vane anemometer and resistance wave wires over a water column depth of 15 m, simultaneous measurements of the momentum flux and sea surface wave spectra were acquired from the Pisa mast, 28 km offshore in the German Bight during autumn and winter 1979. These data were analyzed to identify the relationship between wind stress and surface waves. It was found that wind stresses for wind speeds above 15 m/s were regularly higher than open ocean wind stresses as reported by Smith (1980) and by Large and Pond (1981) for the same mean wind speed. These results, when described in terms of the drag coefficient, compared closely with the results of Sheppard et al. (1972), who collected surface layer statistics over Lough Neagh, Northern Ireland. After modeling the surface waves of the North Sea as a function of wave saturation (or wave age), it became evident that variations in the magnitude of the drag coefficient could be explained by coincident variations in the surface wave energy spectrum. By applying the wave dependent roughness length model described by Kitaigorodskii (1973), the North Sea drag coefficient was predicted to be larger than drag coefficients reported from the open sea.

Geernaert, G. L.↗

Determination of lift and drag characteristics of Space Shuttle Orbiter using maximum likelihood estimation technique

This paper presents the technique and results of maximum likelihood estimation used to determine lift and drag characteristics of the Space Shuttle Orbiter. Maximum likelihood estimation uses measurable parameters to estimate nonmeasurable parameters. The nonmeasurable parameters for this case are elements of a nonlinear, dynamic model of the orbiter. The estimated parameters are used to evaluate a cost function that computes the differences between the measured and estimated longitudinal parameters. The case presented is a dynamic analysis. This places less restriction on pitching motion and can provide additional information about the orbiter such as lift and drag characteristics at conditions other than trim, instrument biases, and pitching moment characteristics. In addition, an output of the analysis is an estimate of the values for the individual components of lift and drag that contribute to the total lift and drag. The results show that maximum likelihood estimation is a useful tool for analysis of Space Shuttle Orbiter performance and is also applicable to parameter analysis of other types of aircraft.

Trujillo, B. M.↗

Formationkeeping of Spacecraft via Differential Drag

This paper examines the use of differential drag in the formationkeeping of spacecraft. In many future space missions one satellite will be required to fly in a specific position with respect to another satellite; this action is referred to as formationkeeping. In this study, differential drag is the difference in drag between the two satellites. Reasons to use differential drag as an actuator for formationkeeping include the avoidance of jet plume impingement effects on closely spaced satellites and possible fuel savings. The equations of relative motion between the two satellites are derived and a mathematical transformation is made to reduce the formationkeeping problem to the simultaneous solution of a double integrator and a harmonic oscillator. A two-part control law is developed that simultaneously and dependently solves the double oscillator and harmonic integrator. Results are presented of eight test cases being driven to a target position; two different simulations are used. The validity of assumptions made in the derivation of the control law is examined in the comparison of similar test cases run through different simulations. The control law developed can drive a satellite from an initial position to a target position and maintain the satellite at that location.

Leonard, Carolina Lee↗

Enhanced viscous flow drag reduction using acoustic excitation

Proper acoustic excitation of a single large-eddy break-up device can increase the resulting drag reduction and, after approximately 40 to 50 delta downstream, provide net drag reduction. Precise optimization of the input time delay, amplitude and response threshold is difficult but possible to achieve. Drag reduction is improved with optimized conditions. The possibility of optimized processing strongly suggests a mechanism which involves interaction of the acoustic waves and large eddies at the trailing edge of the large eddy break-up device. Although the mechanism for spreading of this phenomenon is unknown, it is apparent that the drag reduction effect does tend to spread spanwise as the flow convects downstream. The phenomenon is not unique to a particular blade configuration or flow velocity, although all data have been obtained at relatively low Reynolds numbers. The general repeatibility of the results for small configuration changes serves as verification of the phenomenon.

Nagel, Robert T.↗

Investigation of generic hub fairing and pylon shapes to reduce hub drag

Reported are investigations of fairing configurations pointed toward substantially reducing hub drag. Experimental investigations have shown the importance of hub-fairing camber, lower-surface curvature, and relative size of the drag. The significance of pylon and hub fairings in combination have also been shown. Model test data presented here documented these findings, and also showed the effect of gaps and hub-fairing inclination angle on drag. From a drag standpoint, the best hub fairing had a circular arc, upper-surface curvature, a flat bottom surface, and 8.75% camber.

Stroub, Robert H.↗

Drag reducing outer-layer devices in rough wall turbulent boundary layers

The ability of outer-layer devices to reduce wall shear stress over a substantial streamwise distance in rough-wall turbulent boundary layers has been studied experimentally. The devices examined are a pair of thin flat ribbons placed in tandem as well as those having symmetric airfoil sections. The wall conditions examined are smooth, d- and k-type transverse-groove and sandgrain roughnesses. The wall drag is found to be reduced from the respective normal levels in all rough walls. All k-type rough walls exhibit a similar level of relative wall drag reduction which is also smaller than that in a smooth-wall. The d-type rough walls exhibit a transitional behaviour - the relative wall drag reduction drops from the smooth wall level to that of the k-type roughness with increasing roughness Reynolds number. However, the absolute reductions in the local wall shear stress are similar in both the rough and smooth walls. On the other hand, the relative reductions are lower in the rough walls because of a higher reference drag which is caused by the unique presence of a pressure component on which the devices are not as effective.

Bandyopadhyay, P. R.↗

The effect of flow oscillations on cavity drag

An experimental investigation of flow over an axisymmetric cavity shows that self-sustained, periodic oscillations of the cavity shear layer are associated with low cavity drag. In this low-drag mode the flow regulates itself to fix the mean-shear-layer stagnation point at the downstream corner. Above a critical value of the cavity width-to-depth ratio there is an abrupt and large increase of drag due to the onset of the 'wake mode' of instability. It is also shown by measurement of the momentum balance how the drag of the cavity is related to the state of the shear layer, as defined by the mean momentum transport and the Reynolds stress, and how these are related to the amplifying oscillations in the shear layer. The cavity shear layer is found to be different, in several respects, from a free shear layer.

Gharib, M.↗

Flight and wind-tunnel measurements showing base drag reduction provided by a trailing disk for high Reynolds number turbulent flow for subsonic and transonic Mach numbers

The effectiveness of a trailing disk, or trapped vortex concept, in reducing the base drag of a large body of revolution was studied from measurements made both in flight and in a wind tunnel. Pressure data obtained for the flight experiment, and both pressure and force balance data were obtained for the wind tunnel experiment. The flight test also included data obtained from a hemispherical base. The experiment demonstrated the significant base drag reduction capability of the trailing disk to Mach 0.93 and to Reynolds numbers up to 80 times greater than for earlier studies. For the trailing disk data from the flight experiment, the maximum decrease in base drag ranged form 0.08 to 0.07 as Mach number increased from 0.70 to 0.93. Aircraft angles of attack ranged from 3.9 to 6.6 deg for the flight data. For the trailing disk data from the wind tunnel experiment, the maximum decrease in base and total drag ranged from 0.08 to 0.05 for the approximately 0 deg angle of attack data as Mach number increased from 0.30 to 0.82.

Powers, Sheryll Goecke↗

Advanced natural laminar flow airfoil with high lift to drag ratio

An experimental verification of a high performance natural laminar flow (NLF) airfoil for low speed and high Reynolds number applications was completed in the Langley Low Turbulence Pressure Tunnel (LTPT). Theoretical development allowed for the achievement of 0.70 chord laminar flow on both surfaces by the use of accelerated flow as long as tunnel turbulence did not cause upstream movement of transition with increasing chord Reynolds number. With such a rearward pressure recovery, a concave type deceleration was implemented. Two-dimensional theoretical analysis indicated that a minimum profile drag coefficient of 0.0026 was possible with the desired laminar flow at the design condition. With the three-foot chord two-dimensional model constructed for the LTPT experiment, a minimum profile drag coefficient of 0.0027 was measured at c sub l = 0.41 and Re sub c = 10 x 10 to the 6th power. The low drag bucket was shifted over a considerably large c sub l range by the use of the 12.5 percent chord trailing edge flap. A two-dimensional lift to drag ratio (L/D) was 245. Surprisingly high c sub l max values were obtained for an airfoil of this type. A 0.20 chort split flap with 60 deg deflection was also implemented to verify the airfoil's lift capabilities. A maximum lift coefficient of 2.70 was attained at Reynolds numbers of 3 and 6 million.

Viken, Jeffrey K.↗

A preliminary investigation of drag reduction and mechanism for a blunt body of revolution with slanted base

This is a preliminary study of the drag reduction effect and its mechanism of a blunt body of revolution with a 21-deg slant angle by using a series of base plates. Drag coefficients were measured to investigate the effect of base installation position and plate height. An effective drag reduction device was found. Through the measurement of base pressure and total pressure distribution and flow pattern display, flow characteristics and drag reduction mechanism in the vortex near the wake were investigated.

Xia, Xuejian↗

A low-drag nose-body

In the present investigation of the application of convex-curvature viscous drag reduction to an axisymmetric body, the qualification of a modified mixing-length formulation in several complex two-dimensional and axisymmetric turbulent boundary layers that are primarily curved is followed by the design of a low-drag nose-body for low drag at high subsonic speeds. The longitudinal distribution of the cross-sectional area ratio is found to be critical to boundary layer separation, requiring implementation not over a single long span of curvature but over three short spans. The possibility of a 'net' drag reduction is examined in relation to 'equivalent' nose-bodies.

Bandyopadhyay, P. R.↗

Reduction of hub- and pylon-fairing drag

A wind tunnel test was conducted to obtain data on several drag reduction methods for rotorcraft hubs. The objective of the test was to use small-scale models to develop the technology to substantially reduce hub drag. A helicopter test model, which did not incorporate a rotor, was used to study single-rotor fairing configurations. The rotor shaft assembly was modeled with nonrotating hardware. Drag trend data was obtained for the following fairing configuration changes: hub-fairing camber, hub-fairing thickness ratio, hub-fairing surface curvature, hub-fairing height with respect to the fuselage, inclusion of blade shanks in the hub fairings, hub- and pylon-fairing gaps, pylon-fairing cross-sectional geometry, pylon-fairing thickness ratio and camber. Substantial drag reductions could potentially result from application of the test results to helicopter hub- and pylon-fairing design.

Young, Larry A.↗

Wave drag and high-speed performance of supersonic STOVL fighter configurations

A supersonic STOVL fighter aircraft aerodynamic research program is being conducted at NASA Ames Research Center. The research focuses on technology development for this type of aircraft and includes generating an extensive aerodynamic database and resolving particular aerodynamic uncertainties for various twin- and single-engine aircraft concepts. Highlights of the results from this program are presented. The highlights include propulsion-induced effects on the aircraft drag, prediction capabilities, volume integration for minimizing drag, and wave drag and aerodynamic efficiency comparisons. Results indicate that estimated STOVL fighter performance is roughly comparable to the performance of modern conventional fighters in terms of wave drag and aerodynamic efficiency.

Durston, Donald A.↗

Turbulent structure in low-concentration drag-reducing channel flows

A two-component laser-Doppler velocimeter was used to obtain simultaneous measurements of the velocity components parallel and normal to the wall in two fully developed well-mixed low-concentration drag-reducing channel flows and one turbulent channel flow. For the drag-reducing flows, the average time between bursts was found to increase. Although the basic structure of the fundamental momentum transport event is shown to be the same in these drag-reducing flows, the lower-threshold Reynolds-stress-producing motions were found to be damped, while the higher-threshold motions were not. It is suggested that some strong turbulent motions are needed to maintain extended polymer molecules, which produce a solution with properties that can damp lower threshold turbulence and thereby reduce viscous drag.

Luchik, T. S.↗

Viscous induced drag

A fundamentally new approach to the aircraft minimum induced drag problem is presented. The method, a 'viscous lifting line', is based on the minimum entropy production principle and does not require the planar wake assumption. An approximate, closed form solution is obtained and compared with several classical results. In addition, the problem of optimizing in-plane wing sweep with constant wing root bending moment is considered. Like the classical lifting line theory, this theory predicts that induced drag is proportional to the square of the lift coefficient and inversely proportional to the wing aspect ratio. Unlike the classical theory, it predicts that in-plane wing sweep may significantly reduce induced drag, that induced drag is Reynolds number dependent, and that the optimum spanwise circulation distribution is non-elliptic.

Greene, George C.↗

Wave Drag and High-speed Performance of Supersonic STOVL Fighter Configuration

A supersonic STOVL fighter aircraft aerodynamic research program is under way at NASA Ames Research Center. The research focuses on technology development for this type of aircraft and includes generating an extensive aerodynamic database and resolving particular aerodynamic uncertainties for various twin- and single-engine aircraft concepts. Highlights of the results from this program are presented. The highlights include propulsion-induced effects on the aircraft drag, prediction capabilities, volume integration for minimizing drag, and wave drag and aerodynamic efficiency comparisons. Results indicate that estimated STOVL fighter performance is roughly comparable to the performance of modern conventional fighters in terms of wave drag and aerodynamic efficiency.

Durston, Donald A.↗

Investigation of generic hub fairing and pylon shapes to reduce hub drag

This paper reports investigations of fairing configurations pointed toward substantially reducing hub drag. Experimental investigations have shown the importance of hub-fairing camber,lower-surface curvature, and relative size on the drag. The significance of pylon and hub fairings in combination have also been shown. Model test data presented here documented these findings, and also showed the effect of gaps and hub-fairing inclination angle on drag. From a drag standpoint, the best hub fairing had a circular arc, upper-surface curvature, a flat bottom surface, and 8.75 percent camber.

Stroub, Robert H.↗