Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “differential mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

The Polarimetric Radar Scattering Properties of Oriented Aggregates

The scattering properties of aggregates are studied herein. Early aggregates (<7 monomers) of branched planar crystals and mature aggregates (up to 100 monomers) of columns are randomly generated with varying assumptions about the monomer attachment processes and the orientation behavior during collection. The resulting physical properties of the aggregates correspond well with prior in situ and retrieved sizes and shapes. Assumed azimuthally uniform orientations during collection and monomer pivoting upon attachment resulted in flatter and denser aggregates. The column aggregates had lower density and more spherical shapes than the branched planar crystal aggregates. The scattering properties were calculated using the discrete dipole approximation for a set of orientation angles and transformed to spectral coefficients representing modes of orientation angle variability. The zeroth- and second-order coefficients dominate this variability, with the zeroth-order coefficients representing the scattering properties for randomly oriented particles. The second-order coefficients for backscatter showed differences between horizontal and vertical polarization increasing with density, and these coefficients for specific differential phase increase with both mass and density. Similarly, coefficients for the copolar covariance decreased with density. Rapid changes in the contributions to the radar moments from the second-order coefficients from low to moderate density were observed, likely due to the increasing presence of horizontally aligned monomers in the aggregate structure. Differences in how differential reflectivity and correlation coefficient evolve with the orientation distribution parameters suggest that these measurements, along with specific differential phase and reflectivity, provide complementary information about aggregate sizes, shapes, and orientation distributions.

Cloud microphysics↗
NASA NTRS1981

DC calibration of the strain sensitivity of a single mode optical fiber interferometer

The strain sensitivity of an optical fiber interferometer developed for the detection of pulsed ultrasonic waves in solids has been calibrated. The optical paths in both signal and reference arms of the interferometer are through similar 2 m lengths of ITT-110 single mode fibers mode stripped by index matching at both ends and attached to opposite sides of a 30 cm plexiglas bar 0.3 cm thick. Light from the output ends of both fibers was superimposed to form an interference fringe pattern that was interrogated in the far field to give a signal proportional to the differential optical fiber path length. Strain sensitivity was determined by comparing data obtained by clamping and bending the bar at different lengths to simple cantilever beam theory. Calibration indicates a minimum theoretical detectable strain of less than 10 to the -10.

Claus, R. O.↗
NASA NTRS1986

Spline-based Rayleigh-Ritz methods for the approximation of the natural modes of vibration for flexible beams with tip bodies

Rayleigh-Ritz methods for the approximation of the natural modes for a class of vibration problems involving flexible beams with tip bodies using subspaces of piecewise polynomial spline functions are developed. An abstract operator-theoretic formulation of the eigenvalue problem is derived and spectral properties investigated. The existing theory for spline-based Rayleigh-Ritz methods applied to elliptic differential operators and the approximation properties of interpolatory splines are used to argue convergence and establish rates of convergence. An example and numerical results are discussed.

Rosen, I. G.↗
NASA NTRS1988

Goertler vortices in supersonic boundary layers

The problem of Goertler vortices in compressible boundary layers over concave walls is studied by solving parabolic partial differential equations. The numerical scheme used is based upon a fourth-order accurate compact difference scheme. The results show that both the velocity and temperature fluctuations may lead to a Goertler vortex. The vortex growth rates determined from the present method are found to differ somewhat from those given by normal mode solution. The effects of cooling, heating and pressure gradient are also studied. At a Mach number of 3.5, cooling has a small destabilizing effect. The effect of adverse pressure gradient is also found to be destabilizing on a Mach 8 boundary layer.

Spall, R. E.↗
NASA NTRS1994

Recent lidar technology developments and their influence on measurements of tropospheric water vapor

In this paper the influences of recent technology developments in the areas of lasers, detectors, andoptical filters of a differential absorption lidar (DIAL) system on the measurenent of tropospheric water vapor (H2O) profiles are discussed. The lidar parameters selected are based upon a diode-seeded Ti:sapphire laser that is locked to an H2O line in the 820- or 930-nm band of H2O. To assess the influence of the mode of deployment on the measurement of tropospheric H2O, DIAL performance is evaluated for operation from a medium-altitude (12 km) aircraft, the ground, and space-based systems. It is found that incorporation of these developments could greatly enhance DIAL measurement capability.

Ismail, Syed↗
NASA NTRS2002

Restoring Redundancy to the MAP Propulsion System

The Microwave Anisotropy Probe is a follow-on to the Differential Microwave Radiometer instrument on the Cosmic Background Explorer. Sixteen months before launch, it was discovered that from the time of the critical design review, configuration changes had resulted in a significant migration of the spacecraft's center of mass. As a result, the spacecraft no longer had a viable backup control mode in the event of a failure of the negative pitch axis thruster. Potential solutions to this problem were identified, such as adding thruster plume shields to redirect thruster torque, adding mass to, or removing it from, the spacecraft, adding an additional thruster, moving thrusters, bending thrusters (either nozzles or propellant tubing), or accepting the loss of redundancy for the thruster. The impacts of each solution, including effects on the mass, cost, and fuel budgets, as well as schedule, were considered, and it was decided to bend the thruster propellant tubing of the two roll control thrusters, allowing that pair to be used for back-up control in the negative pitch axis. This paper discusses the problem and the potential solutions, and documents the hardware and software changes that needed to be made to implement the chosen solution. Flight data is presented to show the propulsion system on-orbit performance.

ODonnell, James R., Jr.↗
NASA NTRS1984

Analysis of lateral and torsional vibration characteristics of beams and shafts with end located rotational masses

Partial differential equations are derived for free lateral and torsional vibration of a uniform free-free beam with a rotational mass attached to each extremity. For appropriate boundary conditions, nonlinear algebraic equations are obtained using a symbolic manipulation computer program, the solutions of which enable the computation of the neutral frequencies and mode-shapes. The mode-shapes are linear combinations of trigonometric and hyperbolic sine and cosine functions. A computer program is written for the numerical solution of the algebraic equations mentioned above, which can compute the natural frequencies, mode-shapes, and node points for any given set of parameters, for any given number of modes.

Robertson, D. K.↗
NASA NTRS2009

Phased-array optical whispering gallery mode modulation and method

A whispering gallery mode (WGM) resonator device and method capable of filtering sidebands of optical modulators are provided. The method includes providing an optical resonator adapted to support whispering gallery modes and forming a first field and a second field from a first location and a second location, respectively, at the circumference of the optical resonator and being separated by an arc angle, .alpha.. The method includes adjusting relative phase between the first field and the second field in accordance to a differential phase, .beta., and combining the first and the second fields into an output. Particular selection of the arc angle, .alpha., and the differential phase, .beta., can determine the function of the output.

Strekalov, Dmitry V.↗
NASA NTRS1980

Steady, Oscillatory, and Unsteady Subsonic and Supersonic Aerodynamics, production version (SOUSSA-P 1.1). Volume 1: Theoretical manual

Recent developments of the Green's function method and the computer program SOUSSA (Steady, Oscillatory, and Unsteady Subsonic and Supersonic Aerodynamics) are reviewed and summarized. Applying the Green's function method to the fully unsteady (transient) potential equation yields an integro-differential-delay equation. With spatial discretization by the finite-element method, this equation is approximated by a set of differential-delay equations in time. Time solution by Laplace transform yields a matrix relating the velocity potential to the normal wash. Premultiplying and postmultiplying by the matrices relating generalized forces to the potential and the normal wash to the generalized coordinates one obtains the matrix of the generalized aerodynamic forces. The frequency and mode-shape dependence of this matrix makes the program SOUSSA useful for multiple frequency and repeated mode-shape evaluations.

Morino, L.↗
NASA NTRS1983

Orbiting chains and rings

Two very different, highly flexible, space structures proposed during the last decade which involve analytical solution of certain partial differential equations are discussed. The first structure is an array, or hanging chain of aluminum beads which would serve as a convenient communicator if, under the influence of the Earth's gravity gradient, it assumes a local vertical orientation as it circles the Earth. Two passive schemes have been proposed for damping the rigid modes: twist the wire at the ends to provide non-zero moment of inertia about the vertical, thereby inducing relative motion of the two tips during rigid pitch or roll, and thus exercising a damper; and introduce weak lossy springs between the end sections and the main section; thereby providing linear coupling between the springs and all the in-plane (pitch) modes. The second structure is a complete ring of satellites cabled together at synchronous altitude. By a slight increase in altitude, the cable is in tension. This configuration is, however, unstable, and an active feedback control scheme is required to stabilize it. A possible scheme involves local cable length adjustment based on measurement of local altitude and shape variations and their rates.

Breakwell, J. V.↗
NASA NTRS1991

Likelihood estimation for distributed parameter models for NASA Mini-MAST truss

A maximum likelihood estimation for distributed parameter models of large flexible structures was formulated. Distributed parameter models involve far fewer unknown parameters than independent modal characteristics or finite element models. The closed form solutions for the partial differential equations with corresponding boundary conditions were derived. The closed-form expressions of sensitivity functions led to highly efficient algorithms for analyzing ground or on-orbit test results. For an illustration of this approach, experimental data of the NASA Mini-MAST truss was used. The estimations of modal properties involve lateral bending modes and torsional modes. The results show that distributed parameter models are promising in the parameter estimation of large flexible structures.

Shen, Ji-Yao↗
NASA NTRS1992

Likelihood estimation for distributed parameter models of large beam-like structures

A maximum likelihood estimation for distributed parameter models of large flexible structures was formulated. Distributed parameter models involve far fewer unknown parameters than independent modal characteristics or finite element models. The closed form solutions for the partial differential equations with corresponding boundary conditions were derived. The closed-form expressions of sensitivity functions led to highly efficient algorithms for analyzing ground or on-orbit test results. For an illustration of this approach, experimental data of the NASA Mini-Mast truss was used. The estimations of modal properties involve lateral bending modes and torsional modes. The results show that distributed parameter models are promising in the parameter estimation of large flexible structures.

Shen, J.-Y.↗
NASA NTRS1974

A comprehensive experimental program for investigation of various Omega operational modes with selected data analysis results

The investigations considered are concerned with a better definition of the achievable accuracy and propagation characteristics of Omega and the provision of data which could be used for an analysis to study the potential application of Omega position determination to support other NASA projects. The data collection program is considered along with the experimental equipment employed. Attention is given to the design of the receiving station, aspects of data processing, position measurement errors, differential errors, problems of lane decision, and the definition of the update rate.

Lytle, C. D.↗
NASA NTRS1986

An approximate buckling analysis for rectangular orthotropic plates with centrally located cutouts

An approximate analysis for predicting buckling of rectangular orthotropic composite plates with centrally located cutouts is presented. In this analysis, prebuckling and buckling problems are converted from a two-dimensional to a one-dimensional system of linear differential equations with variable coefficients. The conversion is accomplished by expressing the displacements as series with each element containing a trigonometric function of one coordinate and a coefficient that is an arbitrary function of the other coordinate. Ordinary differential equations are then obtained from a variational principle. Analytical results obtained from the approximate analysis are compared with finite element analyses for isotropic plates and for specially orthotropic plates with central circular cutouts of various sizes. Experimental results for the specially orthotropic plates are also presented. In nearly all cases, the approximate analysis predicts the buckling mode shapes correctly and predicts the buckling loads to within a few percent of the finite element and experimental results.

Nemeth, M. P.↗
NASA NTRS1990

Depth and latitude dependence of the solar internal angular velocity

One of the design goals for the dedicated helioseismology observing state located at Mount Wilson Observatory was the measurement of the internal solar rotation using solar p-mode oscillations. In this paper, the first p-mode splittings obtained from Mount Wilson are reported and compared with those from several previously published studies. It is demonstrated that the present splittings agree quite well with composite frequency splittings obtained from the comparisons. The splittings suggest that the angular velocity in the solar equatorial plane is a function of depth below the photosphere. The latitudinal differential rotation pattern visible at the surface appears to persist at least throughout the solar convection zone.

Rhodes, Edward J., Jr.↗
NASA NTRS1998

Transient Simulation of Pressure Oscillations in the Fuel Feedline of the Fastrac Engine Thrust Chamber

During mainstage testing of the 60,000 lbf thrust Fastrac thrust chamber at MSFC's Test Stand 116 (TS 116), sustained, large amplitude oscillations near 530 Hz were observed in the pressure data. These oscillations were detected both in the RP-1 feedline, downstream of the cavitating venturi, and in the combustion chamber. The driver of the instability is believed to be feedline excitation driven by either periodic cavity collapse at the exit of the cavitating venturi or combustion instability. In covitating venturi, static pressure drops as the flow passes through a constriction resembling a converging-diverging nozzle until the vapor pressure is reached. At the venturi throat, the flow is essentially choked, which is why these devices are typically used for mass flow rate control and disturbance isolation. Typically, a total pressure drop of 15% or more across the venturi is required for cavitation. For much larger pressure differentials, unstable cavities can form and subsequently collapse downstream of the throat. Although the disturbances generated by cavitating venturis is generally considered to be broad-band, this type of phenomena could generate periodic behavior capable of exciting the feedline. An excitation brought about by combustion instability would result from the coupling of a combustion chamber acoustic mode and a feedline resonance frequency. This type of coupling is referred to as "buzz" and is not uncommon for engines in this thrust range.

Bullard, Brad↗
NASA NTRS1978

The Total In-Flight Simulator (TIFS) aerodynamics and systems: Description and analysis

The aerodynamics, control system, instrumentation complement and recording system of the USAF Total In/Flight Simulator (TIFS) airplane are described. A control system that would allow the ailerons to be operated collectively, as well as, differentially to entrance the ability of the vehicle to perform the dual function of maneuver load control and gust alleviation is emphasized. Mathematical prediction of the rigid body and the flexible equations of longitudinal motion using the level 2.01 FLEXSTAB program are included along with a definition of the vehicle geometry, the mass and stiffness distribution, the calculated mode frequencies and mode shapes, and the resulting aerodynamic equations of motion of the flexible vehicle. A complete description of the control and instrumentation system of the aircraft is presented, including analysis, ground test and flight data comparisons of the performance and bandwidth of the aerodynamic surface servos. Proposed modification for improved performance of the servos are also presented.

Andrisani, D., II↗
NASA NTRS1990

Distributed parameter estimation for large beam-like structures for general inputs

In this paper, maximum likelihood estimation for distributed parameter models of large flexible structures has been formulated. Distributed parameter models involve far fewer unknown parameters than independent modal characteristics of finite element models. The closed-form solutions for the partial differential equations with general forced inputs have been derived. The closed-form expressions of the sensitivity functions lead to highly efficient algorithms for analyzing ground or on-orbit test results. Numerical simulations with impulse and step inputs to the NASA Mini-MAST trust have been demonstrated. The estimations of modal properties involve its longitudinal elongation modes, lateral bending modes and torsional modes. The results show that distributed parameter models are promising in the parameter estimation of large flexible structures.

Shen, Ji-Yao↗