Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diamond”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Characterization of diamond thin films deposited by a CO{sub 2} laser-assisted combustion-flame method

Diamond thin films were deposited by a CO{sub 2} laser-assisted O{sub 2}/C{sub 2}H{sub 2}/C{sub 2}H{sub 4} combustion-flame process. The effect of the deposition parameters, in particular the laser wavelength and power, on the film surface morphology, microstructure and phases present was the primary focus of the work. The laser power was set at 100, 400 and 800 W while the wavelength was varied and set at 10.591 {mu}m in the untuned condition and set at 10.532 {mu}m to resonantly match the CH{sub 2}-wagging vibrational mode of the C{sub 2}H{sub 4} molecule when in the tuned condition. When the laser was coupled to the combustion flame during deposition the diamond film growth was enhanced as the lateral grain size increased from 1 {mu}m to greater than 5 {mu}m. The greatest increase in grain size occurred when the wavelength was in the tuned condition. Scanning transmission electron microscopy images from focused-ion beam cross-sectioned samples revealed a sub-layer of smaller grains less than 1 {mu}m in size near the substrate surface at the lower laser powers and untuned wavelength. X-ray diffraction results showed a more intense Diamond (111) peak as the laser power increased from 100 to 800 W for the films deposited with the tuned laser wavelength. Micro-Raman spectra showed a diamond peak nearly twice as intense from the films with the tuned laser wavelength.

36 MATERIALS SCIENCE↗

Photoluminescence studies of growth-sector dependence of nitrogen distribution in synthetic Ib diamond

The photoluminescence technology previously employed to investigate the boron distribution of type IIb diamond has now been applied to study the nitrogen distribution of type Ib diamond. All growth sectors were clearly distinguished by the characteristic colors and the brightness of the synthetic Ib diamond's cathodoluminescence topography. As a measure of the concentration of nitrogen impurity, the nitrogen-vacancy luminescence gave relative concentrations in different growth sectors as: the (111) sector was the highest, followed by the (311), (100) and (511) sectors. The results were reconfirmed by the evidence of the broadened and strengthened zero phonon lines of nitrogen-vacancy center with the increase of nitrogen concentration of type Ib diamond. - Highlights: • The growth sectors were clearly distinguished by CL technology. • The N distribution was investigated by the examination of PL spectroscopy. • Results showed that (111) has the highest N, followed by (311), (100) and (511). • The conclusion was reconfirmed by the PL results of NV center.

36 MATERIALS SCIENCE↗

Strain-induced ordered structure of titanium carbide during depositing diamond on Ti alloy substrate

During the deposition of diamond films on Ti alloy substrates, titanium carbide is a common precipitated phase, preferentially formed at the interfacial region. However, in this case, the precipitation of an ordered structure of titanium carbide has not been reported. In our work, a long periodic ordered structure of TiC has been observed at the deposited diamond film/Ti alloy interface by high resolution transmission electron microscopy (HRTEM). The long periodic ordered structure is identified as 6H-type. The formation mechanism is revealed by comparative studies on the different structures of TiC precipitated under different diamond deposition conditions in terms of deposition time, atmosphere and temperature. A large number of carbon vacancies in the interfacial precipitated TiC phase are verified through electron energy loss spectroscopy (EELS) quantification analysis. However, an ordered arrangement of these carbon vacancies occurs only when the interfacial stress is large enough to induce the precipitation of 6H-type TiC. The supplementary analysis by X-ray diffraction (XRD) further confirms that additional diffraction peaks presented in the XRD patterns are corresponding to the precipitation of 6H-type TiC. - Highlights: •Different structures of TiC are observed during deposited diamond on Ti alloy. •One is common NaCl structure, the other is periodic structure. •The periodic structure is identified as 6H-type by HRTEM. •Carbon vacancies are verified to always exist in the TiC phase. •The precipitation of 6H-type TiC is mainly affected by interfacial stress.

36 MATERIALS SCIENCE↗

Divergence study and emittance measurements for the electron beam emitted from a diamond pyramid

This paper reports the results of a divergence study and emittance measurements for an electron beam emitted from a single diamond pyramid in a sparse diamond field-emitter array (DFEA) cathode. DFEA cathodes are arrays of micrometer scale diamond pyramids with nanometer scale tips. A single diamond pyramid produces currents as high as 10 μA from a small surface area. DFEA cathodes are expected to be a good beam source for compact dielectric laser accelerators. For the electron beam divergence experiment, we have designed and assembled a test stand consisting of a DFEA cathode, a mesh anode, and a screen. We measured current and the size of the beam on the screen as functions of the distance between the cathode and the anode, the size of a pyramid’s base, and applied voltage on the cathode. In order to perform beam emittance measurements, we designed and fabricated a magnetic lens to be placed between the mesh and the screen. By measuring the size of the beam for different distances between the lens and the screen, we estimate the beam’s emittance. Here, we also simulated the electron beam dynamics with Computer Simulation Technology Studio and General Particle Tracer codes. Experimentally measured divergence angles and normalized transverse emittance show good agreement with simulations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Core-Shell Diamond as a Support for Solid-Phase Extraction and High-Performance Liquid Chromatography

We report the formation of core-shell diamond particles for solid phase extraction (SPE) and high performance liquid chromatography (HPLC) made by layer-by-layer (LbL) deposition. Their synthesis begins with the amine functionalization of microdiamond by its immersion in an aqueous solution of a primary amine-containing polymer (polyallylamine (PAAm)). The amine-terminated microdiamond is then immersed in an aqueous suspension of nanodiamond, which leads to adsorption of the nanodiamond. Alternating (self-limiting) immersions in the solutions of the amine-containing polymer and the suspension of nanodiamond are continued until the desired number of nanodiamond layers is formed around the microdiamond. Finally, the core-shell particles are cross-linked with 1,2,5,6-diepoxycyclooctane or reacted with 1,2-epoxyoctadecane. Layer-by-layer deposition of PAAm and nanodiamond is also studied on planar Si/SiO2 surfaces, which were characterized by SEM, Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA). Core-shell particles are characterized by diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), environmental scanning electron microscopy (ESEM), and Brunauer Emmett Teller (BET) surface area and pore size measurements. Larger (ca. 50 μm) core-shell diamond particles have much higher surface areas, and analyte loading capacities in SPE than nonporous solid diamond particles. Smaller (ca. 3 μm), normal and reversed phase, core-shell diamond particles have been used for HPLC, with 36,300 plates per meter for mesitylene in a separation of benzene and alkyl benzenes on a C18 adsorbent, and 54,800 plates per meter for diazinon in a similar separation of two pesticides.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Extensively Microtwinned Diamond with Nanolaminates of Lonsdaleite Formed by Flash Laser Heating of Glassy Carbon

Diamond’s unique properties on the nanoscale make it one of the most important materials for use in biosensors and quantum computing and for components that can withstand the harsh environments of space. We synthesize oriented, faceted diamond particles by flash laser heating of glassy carbon at 16 GPa and 2300 K. Detailed transmission electron microscopy shows them to consist of a mosaic of diamond nanocrystals frequently joined at twin boundaries forming microtwins. Striking 3-fold translational periodicity was observed in both imaging and diffraction. This periodicity was shown to originate from nanodimensional wedge-shaped overlapping regions of twinned diamond and not from a possible 9R polytype, which has also been reported in other group IVa elements and water ice. Extended bilayers of hexagonal layer stacking were observed, forming lonsdaleite nanolaminates. In conclusion, the particles exhibited optical fluorescence with a rapid quench time (<1 ns) attributed to their unique twinned microstructure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Plasmonic Diamond Membranes for Ultrafast Silicon Vacancy Emission

Silicon vacancy centers (SiVs) in diamond have emerged as a promising platform for quantum sciences due to their excellent photostability, minimal spectral diffusion, and substantial zero-phonon line emission. However, enhancing their slow nanosecond excited-state lifetime by coupling to optical cavities remains an outstanding challenge, as current demonstrations are limited to ~10-fold. Here, we couple negatively charged SiVs to sub-diffraction-limited plasmonic cavities and achieve an instrument-limited ≤8 ps lifetime, corresponding to a 135-fold spontaneous emission rate enhancement and a 19-fold photoluminescence enhancement. Nanoparticles are printed on ultrathin diamond membranes on gold films which create arrays of plasmonic nanogap cavities with ultrasmall volumes. SiVs implanted at 5 and 10 nm depths are examined to elucidate surface effects on their lifetime and brightness. The interplay between cavity, implantation depth, and ultrathin diamond membranes provides insights into generating ultrafast, bright SiV emission for next-generation diamond devices.

Purcell enhancement↗

Heterogenous Integration of Boron-Doped p -Diamond with Monolayer n -MoS 2 for PN Junctions Operating at Room Temperature

Diamond has tremendous potential for power electronics, due to its superior thermal conductivity, large electric field strength, and high carrier mobilities. However, the absence of a reliable room temperature n-type transport has impeded any advancements in diamond-based electronics. Here, we circumvent this bottleneck by integrating n-type two-dimensional (2D) monolayers of molybdenum disulfide (MoS 2 ) with boron doped p-type single crystal diamond and demonstrate 2D/3D heterostructure-based PN junction diodes that operate at room temperature with excellent rectification characteristics. Our diodes achieve a maximum forward current density (J D ) of ∼4000 A/cm 2 , an ideality factor (η) value of ∼3.7, and a rectification ratio (RR) of 10 6 . We find that the origin of current rectification stems from the interlayer recombination of majority carriers driven by direct tunnelling (DT) and Fowler Nordheim (FN) tunnelling mechanisms. In conclusion, our demonstration can open new avenues for diamond-based power electronics through its integration with 2D materials.

2D/3D integration↗

Multiple substrate microwave plasma-assisted chemical vapor deposition single crystal diamond synthesis

A multiple substrate, microwave plasma-assisted chemical vapor deposition synthesis process for single crystal diamond (SCD) is demonstrated using a 915 MHz reactor. Diamond synthesis was performed using input chemistries of 6-8% of CH{sub 4}/H{sub 2}, microwave input powers of 10-11.5 kW, substrate temperatures of 1100-1200 deg. C, and pressures of 110-135 Torr. The simultaneous synthesis of SCD over 70 diamond seeds yielded good quality SCD with deposition rates of 14-21 {mu}m/h. Multiple deposition runs totaling 145 h of deposition time added 1.8-2.5 mm of diamond material to each of the 70 seed crystals.

36 MATERIALS SCIENCE↗

Containment of fluid samples in the hydrothermal diamond-anvil cell without the use of metal gaskets: Performance and advantages for in situ analysis

Metal gaskets (Re, Ir, Inconel, or stainless steel) normally used to contain fluid samples in the hydrothermal diamond-anvil cell (HDAC) are sometimes undesirable due to possible contamination and to gasket deformation at high pressures and temperatures resulting in nonisochoric behavior. Furthermore, in x-ray spectroscopic experiments, metal gaskets may attenuate the incident x-ray beam and emitted fluorescence x-rays, and the interaction of scattered radiation with the gasket may produce fluorescence that interferes with the x-ray spectrum of the sample. New arrangements and procedures were tested for the operation of the HDAC without using the metal gaskets. Distilled, de-ionized water was loaded into the sample chamber, a laser-milled recess 300 {micro}m in diameter and - 50 {micro}m deep centered in the 1.0 mm face of the lower diamond anvil, and sealed by pressing the top diamond anvil face directly against the lower one without a metal gasket in between. A maximum sample pressure of 202 MPa at 617 C was maintained for a duration of 10 min without evidence of leakage. A small change in fluid density was observed in one experiment where the sample was held at 266 MPa at 708 C for 10 min. The gasketless HDAC was also employed in x-ray absorption spectroscopy experiments, where, in addition to the sample chamber in the lower diamond, two grooves were milled at a 90{sup o} angle to each other around the sample chamber to minimize the attenuation of incident and fluorescent x rays. With a minimum distance between the sample chamber and the grooves of 80 {micro}m, a pressure of 76 MPa at 500 C was maintained for 2 h with no change in the original fluid density.

36 MATERIALS SCIENCE↗

Coupling of nitrogen-vacancy centers in diamond to a GaP waveguide

The optical coupling of guided modes in a GaP waveguide to nitrogen-vacancy (NV) centers in diamond is demonstrated. The electric field penetration into diamond and the loss of the guided mode are measured. The results indicate that the GaP-diamond system could be useful in realizing coupled microcavity-NV devices for quantum information processing in diamond.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A comparison of diamond growth rate using in-liquid and conventional plasma chemical vapor deposition methods

In order to make high-speed deposition of diamond effective, diamond growth rates for gas-phase microwave plasma chemical vapor deposition and in-liquid microwave plasma chemical vapor deposition are compared. A mixed gas of methane and hydrogen is used as the source gas for the gas-phase deposition, and a methanol solution of ethanol is used as the source liquid for the in-liquid deposition. The experimental system pressure is in the range of 60-150 kPa. While the growth rate of diamond increases as the pressure increases, the amount of input microwave energy per unit volume of diamond is 1 kW h/mm{sup 3} regardless of the method used. Since the in-liquid deposition method provides a superior cooling effect through the evaporation of the liquid itself, a higher electric input power can be applied to the electrodes under higher pressure environments. The growth rate of in-liquid microwave plasma chemical vapor deposition process is found to be greater than conventional gas-phase microwave plasma chemical vapor deposition process under the same pressure conditions.

36 MATERIALS SCIENCE↗

Temperature enhancement of secondary electron emission from hydrogenated diamond films

The effect of temperature on the stability of the secondary electron emission (SEE) yield from approx100-nm-thick continuous diamond films is reported. At room temperature, the SEE yield was found to decay as a function of electron irradiation dose. The SEE yield is observed to increase significantly upon heating of the diamond surface. Furthermore, by employing moderate temperatures, the decay of the SEE yield observed at room temperature is inhibited, showing a nearly constant yield with electron dose at 200 deg. C. The results are explained in terms of the temperature dependence of the electron beam-induced hydrogen desorption from the diamond surface and surface band bending. These findings demonstrate that the longevity of diamond films in practical applications of SEE can be increased by moderate heating.

36 MATERIALS SCIENCE↗

Chemical vapor deposition diamond based multilayered radiation detector: Physical analysis of detection properties

Recently, solid state photovoltaic Schottky diodes, able to detect ionizing radiation, in particular, x-ray and ultraviolet radiation, have been developed at the University of Rome 'Tor Vergata'. We report on a physical and electrical properties analysis of the device and a detailed study of its detection capabilities as determined by its electrical properties. The design of the device is based on a metal/nominally intrinsic/p-type diamond layered structure obtained by microwave plasma chemical vapor deposition of homoepitaxial single crystal diamond followed by thermal evaporation of a metallic contact. The device can operate in an unbiased mode by using the built-in potential arising from the electrode-diamond junction. We compare the expected response of the device to photons of various energies calculated through Monte Carlo simulation with experimental data collected in a well controlled experimental setup i.e., monochromatic high flux x-ray beams from 6 to 20 keV, available at the Diamond Light Source synchrotron in Harwell (U.K.).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Diamond Photodetectors for X-Ray Absorption Spectroscopy Applications

Synchrotron radiation (SR) is a fundamental tool for X-ray research. In particular, X-ray absorption spectroscopy (XAS) accesses information as electronic properties, local structure or chemical-physical state in condensed-matter studies. Ionization chambers (ICs) are the most widely used XAS detectors for transmission measurements because of their reliability, high linearity and good stability. Recently, solid-state detectors have been considered and Si p-i-n has been applied to high fluxes (10{sup 11} ph/s), where the linearity of ICs is no longer guaranteed. Silicon photodiodes exhibit an extremely linear response in at least 5 decades but show diffraction peaks. Diamond is an ideal substrate to produce radiation-hard, low dark current (<1 pA/cm{sup 2}), visible-blind and fast-response X-ray detectors with a high S/N ratio. Diamond detectors were tested as SR monitor capable to withstand the high photon flux density of the 3{sup rd} generation SR sources. Being the lowest X-ray-absorbing solid-state dielectric material, diamond maximizes the flux through thin self-standing devices with minimal spectral effect down to the soft x-ray range. We will present results of X-ray tests of photoconductors based on different diamond substrates. The results will be compared to standard ICs for XAS applications in terms of spectral quality, noise and linearity in the 4-13 keV energy range.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electrochemical hydrogen termination of boron-doped diamond

Boron-doped diamond is a promising transducer material for numerous devices which are designed for contact with electrolytes. For optimized electron transfer the surface of diamond needs to be hydrogen terminated. Up to now H-termination of diamond is done by plasma chemical vapor deposition techniques. In this paper, we show that boron-doped diamond can be H-terminated electrochemically by applying negative voltages in acidic solutions. Electrochemical H-termination generates a clean surface with virtually no carbon-oxygen bonds (x-ray photoelectron spectroscopy), a reduced electron affinity (scanning electron microscopy), a highly hydrophobic surface (water contact angle), and a fast electron exchange with Fe(CN){sub 6}{sup -3/-4} (cyclic voltammetry).

36 MATERIALS SCIENCE↗

A planar refractive x-ray lens made of nanocrystalline diamond

Diamond has unique properties which make it the ideal material for use in synchrotron instrumentation. X-ray optics made of diamond are almost transparent, they possess strength, and are subject to very low thermal expansion; therefore they will be able to withstand the powerful beams generated by fourth-generation light sources without compromising brilliance. For this reason, several groups are attempting fabrication of refractive lenses and zone plates made of diamond. Lithography and, in general, microfabrication technology, are the ultimate tools for the innovation of synchrotron focusing optics. We propose to combine modern silicon microtechnology with advanced deposition methods to fabricate nanocrystalline-diamond lenses for third- and fourth-generation synchrotron sources. The fabrication method is described here and microfocusing synchrotron tests are illustrated.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A molecular dynamics study of diamond and graphite under tritium bombardment

Carbon has proven to be a promising plasma facing material in tokamak reactors because of its high thermal conductivity and limited radiative cooling as a plasma contaminant. It is used in a range of forms, mostly graphitic or amorphous. Diamond, however, has superior thermal properties to other forms of carbon but has been largely overlooked due to fears of graphitisation. Tritium retention is, perhaps, the major disadvantage of using carbon as a plasma facing material in a deuterium-tritium fusion reactor. Here, we use molecular dynamics to study the relative performance of diamond and graphite on exposure to tritium bombardment. We model the cumulative bombarded of diamond and graphitic surfaces with a high flux (10{sup 29} m{sup -2} s{sup -1}) of low energy 15 eV tritium atoms. This was done for substrate temperatures in the range 300-2100 K. Below temperatures of graphitisation ({approx}1000 K) the diamond structure confined tritium to the upper surface, this inhibited further structural damage and resulted in lower total retention. The graphitic surface allowed for deeper tritium penetration and therefore greater retention. These results corroborate with recent experimental evidence.

36 MATERIALS SCIENCE↗