Results for “delay errors.” — Page 25

NASA NTRSDate not supplied

Spectrally Dependent Radiometric Measurement Errors Due to Ccd Serial Pixel-to-Pixel Readout Interference in the Ocean Color Instrument of the NASA PACE Mission

The Ocean Color Instrument on NASA’s PACE mission is a 322 887 nm hyperspectral imager with 1 km x 1 km nadir spatial resolution and 5 nm spectral resolution utilizing charge-coupled devices (CCDs) operating in Time Delay Integration (TDI) mode where each TDI column represents a different wavelength in 0.625 nm increments. After TDI, the charge is moved into serial output pixels and read out. The spatial resolution requires an 8.5 MHz readout rate. This only allows 59 ns for the CCD reset and video to be asserted and settled before sampling. The response exhibits serial pixel-to-pixel readout interference due to the lack of full settling. Each serial pixel value has a dependence on the value of the preceding pixel value. This leads to a spectrally dependent radiometric measurement error of up to 0.3 %. We explain the operation of the detection system, the behavior of the interference, and show the resulting measurement error based on data from both ground testing and on-orbit characterization.

Remote Sensing↗

NASA NTRS2024

Spectrally Dependent Radiometric Measurement Errors Due to CCD Serial Pixel-to-Pixel Readout Interference in the Ocean Color Instrument of the NASA PACE Mission

The Ocean Color Instrument on NASA’s PACE mission is a 322 887 nm hyperspectral imager with 1 km x 1 km nadir spatial resolution and 5 nm spectral resolution utilizing charge-coupled devices (CCDs) operating in Time Delay Integration (TDI) mode where each TDI column represents a different wavelength in 0.625 nm increments. After TDI, the charge is moved into serial output pixels and read out. The spatial resolution requires an 8.5 MHz readout rate. This only allows 59 ns for the CCD reset and video to be asserted and settled before sampling. The response exhibits serial pixel-to-pixel readout interference due to the lack of full settling. Each serial pixel value has a dependence on the value of the preceding pixel value. This leads to a spectrally dependent radiometric measurement error of up to 0.3 %. We explain the operation of the detection system, the behavior of the interference, and show the resulting measurement error based on data from both ground testing and on-orbit characterization.

Remote Sensing↗

NASA NTRSDate not supplied

From Formal Errors Towards Realistic Uncertainties

Evaluation of uncertainties of geodetic parameter estimates is the problem that is not yet solved in a satisfactory way. A direct evaluation of the uncertainties derived from a least square solution is labeled "formal" and is usually biased, sometimes up to an order of magnitude. Customary, the use of formal errors for scientific analysis is discouraged. We claim that the root of the problem is neglecting off-diagonal elements in the variance-covariance matrix of the noise in the data. A careful reconstruction of the full variance-covariance matrix, including the off-diagonal terms greatly improves realism of uncertainty estimates derived from least squares. We processed the dataset of VLBI group delays and built a prior variance-covariance of the atmosphere-driven noise based on analysis of the output of NASA high-resolution numerical weather models. We found that the uncertainties of parameter estimates derived from this least square solution that uses such variance-covariance matrices become much closer to realistic errors. We consider approaches for implementation of this method in routine data analysis of space geodesy data.

Leonid Petrov↗

NASA NTRS1977

Method of and means for testing a tape record/playback system

A tape record/playback system was tested by first deriving an analog test signal and a band-limited digital reference signal from a pseudo-noise sequence generator driven by a clock signal. It recorded the signals on respective tracks of the system during operation in a record mode. During the playback mode of operation of the system, a delayed analog reference signal without time base variations was reconstructed from the played back reference signal. It was compared with the played back test signal in order to obtain an error signal that was a measure of the performance of the system.

Wallace, G. R.↗

NASA NTRS1980

Pseudonoise code tracking loop

A delay-locked loop is presented for tracking a pseudonoise (PN) reference code in an incoming communication signal. The loop is less sensitive to gain imbalances, which can otherwise introduce timing errors in the PN reference code formed by the loop.

Laflame, D. T.↗

NASA NTRS2012

Addressing the Influence of Space Weather on Airline Navigation

The advent of satellite-based augmentation systems has made it possible to navigate aircraft safely using radio signals emitted by global navigation satellite systems (GNSS) such as the Global Positioning System. As a signal propagates through the earth's ionosphere, it suffers delay that is proportional to the total electron content encountered along the raypath. Since the magnitude of this total electron content is strongly influenced by space weather, the safety and reliability of GNSS for airline navigation requires continual monitoring of the state of the ionosphere and calibration of ionospheric delay. This paper examines the impact of space weather on GNSS-based navigation and provides an overview of how the Wide Area Augmentation System protects its users from positioning error due to ionospheric disturbances

airline navigation↗

NASA NTRS2010

Spotlight-Mode Synthetic Aperture Radar Processing for High-Resolution Lunar Mapping

During the 2008-2009 year, the Goldstone Solar System Radar was upgraded to support radar mapping of the lunar poles at 4 m resolution. The finer resolution of the new system and the accompanying migration through resolution cells called for spotlight, rather than delay-Doppler, imaging techniques. A new pre-processing system supports fast-time Doppler removal and motion compensation to a point. Two spotlight imaging techniques which compensate for phase errors due to i) out of focus-plane motion of the radar and ii) local topography, have been implemented and tested. One is based on the polar format algorithm followed by a unique autofocus technique, the other is a full bistatic time-domain backprojection technique. The processing system yields imagery of the specified resolution. Products enabled by this new system include topographic mapping through radar interferometry, and change detection techniques (amplitude and coherent change) for geolocation of the NASA LCROSS mission impact site.

SAR↗

NASA NTRS2015

Phase-Based Adaptive Estimation of Magnitude-Squared Coherence Between Turbofan Internal Sensors and Far-Field Microphone Signals

A cross-power spectrum phase based adaptive technique is discussed which iteratively determines the time delay between two digitized signals that are coherent. The adaptive delay algorithm belongs to a class of algorithms that identifies a minimum of a pattern matching function. The algorithm uses a gradient technique to find the value of the adaptive delay that minimizes a cost function based in part on the slope of a linear function that fits the measured cross power spectrum phase and in part on the standard error of the curve fit. This procedure is applied to data from a Honeywell TECH977 static-engine test. Data was obtained using a combustor probe, two turbine exit probes, and far-field microphones. Signals from this instrumentation are used estimate the post-combustion residence time in the combustor. Comparison with previous studies of the post-combustion residence time validates this approach. In addition, the procedure removes the bias due to misalignment of signals in the calculation of coherence which is a first step in applying array processing methods to the magnitude squared coherence data. The procedure also provides an estimate of the cross-spectrum phase-offset.

Combustion↗

NASA NTRS2017

Novel Estimation of Pilot Performance Characteristics

Two mechanisms internal to the pilot that affect performance during a tracking task are: 1) Pilot equalization (i.e. lead/lag); and 2) Pilot gain (i.e. sensitivity to the error signal). For some applications McRuer's Crossover Model can be used to anticipate what equalization will be employed to control a vehicle's dynamics. McRuer also established approximate time delays associated with different types of equalization - the more cognitive processing that is required due to equalization difficulty, the larger the time delay. However, the Crossover Model does not predict what the pilot gain will be. A nonlinear pilot control technique, observed and coined by the authors as 'amplitude clipping', is shown to improve stability, performance, and reduce workload when employed with vehicle dynamics that require high lead compensation by the pilot. Combining linear and nonlinear methods a novel approach is used to measure the pilot control parameters when amplitude clipping is present, allowing precise measurement in real time of key pilot control parameters. Based on the results of an experiment which was designed to probe workload primary drivers, a method is developed that estimates pilot spare capacity from readily observable measures and is tested for generality using multi-axis flight data. This paper documents the initial steps to developing a novel, simple objective metric for assessing pilot workload and its variation over time across a wide variety of tasks. Additionally, it offers a tangible, easily implementable methodology for anticipating a pilot's operating parameters and workload, and an effective design tool. The model shows promise in being able to precisely predict the actual pilot settings and workload, and observed tolerance of pilot parameter variation over the course of operation. Finally, an approach is proposed for generating Cooper-Harper ratings based on the workload and parameter estimation methodology.

Human pilot models↗

NASA NTRS2018

Using an Automated Air Traffic Simulation Capability for a Parametric Study in Traffic Flow Management

Flight delays occur when demand for capacity-constrained airspace or airports exceeds predicted capacity. Demand for capacity-constrained airspace or airports can be controlled by a series of Traffic Management Initiatives (TMIs), which use departure and airborne delays, as well as pre-departure and airborne reroutes, to manage access to the constrained resources. Two systems exist in current and planned future operations to address imbalances between demand and capacity. The Collaborative Trajectory Options Program (CTOP) reduces demand to constrained resources by assigning strategic departure delay and pre-departure reroutes. Reroutes are selected from Trajectory Options Sets (TOSs) submitted by airlines. As flights approach the constrained resource, the Time-Based Flow Management System (TBFM) is used to assign tactical delay to satisfy constraints. This paper describes experiments performed to study the impact of varying levels of airline participation in CTOP via submission of TOSs on ground delay and flight time, and the impact of departure uncertainty on TBFM delays. Results suggest that as CTOP participation increases, average ground delays decrease for all airlines, but to the greatest extent for airlines participating in CTOP. A threshold in CTOP participation, which varies with the constraint capacity, is identified beyond which there is relatively little further reduction in average ground delays. Similarly, given the likely level of CTOP participation, the capacity reduction for which CTOP would be an appropriate TMI is also identified. Results also suggest that high average departure errors and high variability in departure error can make the prioritization of TBFM internal departures in TBFM metering and scheduling infeasible. Departure errors at current levels are, however, acceptable.

CTOP↗

NASA NTRS2018

Using an Automated Air Traffic Simulation Capability for a Parametric Study in Traffic Flow Management

Flight delays occur when demand for capacity-constrained airspace or airports exceeds predicted capacity. Demand for capacity-constrained airspace or airports can be controlled by a series of Traffic Management Initiatives (TMIs), which use departure and airborne delays, as well as pre-departure and airborne reroutes, to manage access to the constrained resources. Two systems exist in current and planned future operations to address imbalances between demand and capacity. The Collaborative Trajectory Options Program (CTOP) reduces demand to constrained resources by assigning strategic departure delay and pre-departure reroutes. Reroutes are selected from Trajectory Options Sets (TOSs) submitted by airlines. As flights approach the constrained resource, the Time-Based Flow Management System (TBFM) is used to assign tactical delay to satisfy constraints. This paper describes experiments performed to study the impact of varying levels of airline participation in CTOP via submission of TOSs on ground delay and flight time, and the impact of departure uncertainty on TBFM delays. Results suggest that as CTOP participation increases, average ground delays decrease for all airlines, but to the greatest extent for airlines participating in CTOP. A threshold in CTOP participation, which varies with the constraint capacity, is identified beyond which there is relatively little further reduction in average ground delays. Similarly, given the likely level of CTOP participation, the capacity reduction for which CTOP would be an appropriate TMI is also identified. Results also suggest that high average departure errors and high variability in departure error can make the prioritization of TBFM internal departures in TBFM metering and scheduling infeasible. Departure errors at current levels are, however, acceptable.

integrated demand management↗

NASA NTRSDate not supplied

Simulated Multipath Using Software Generated GPS Signals

Depending on the environment, multipath can be one of the largest error sources contributing to degradation in Global Navigation Satellite System (GNSS) (e.g., GPS) performance. Multipath is a phenomenon that occurs as radio signals reflect off of surfaces, such as buildings, producing multiple copies of the original signal. When this occurs with GPS signals, it results in one or more delayed signals arriving at the receiver with or without the on-time/direct GPS signal. The receiver measures the composite of these signals which, depending on the severity of the multipath, can substantially degrade the accuracy of the receiver's calculated position. Multipath is commonly experienced in cities due to tall buildings and its mitigation is an ongoing area of study. This research demonstrates a novel approach for simulating GPS multipath through the modification of an open-source tool, GPS-SDR-SIM. The resulting additional testing capability could allow for improved development of multipath mitigating technologies. Currently, open-source tools for simulating GPS signals are available and can be used in the testing and evaluation of GPS receiver equipment. These tools can generate GPS signals that, when used by a GPS receiver, result in computation of a position solution that was pre-determined at the time of signal generation. That is, the signals produced are properly formed for the pre-determined location and result in the receiver reporting that position. This allows for a GPS receiver under test to be exposed to various simulated locations and conditions without having to be physically subjected to them. Additionally, while these signals are generated by a software simulation, they can be processed by real or software defined GPS receivers. This work utilizes the GPS-SDR-SIM software tool for GPS signal generation and while this tool does implement some sources of error that are inherent to GPS, it cannot inject multipath. GPS-SDR-SIM was modified in this effort to produce additional copies of signals with pre-determined delays. These additional delayed signals mimic multipath and represent what happens to GPS signals in the real world as they reflect off of surfaces and arrive at a receiver in place of or alongside the direct GPS signal. A successful proof of concept was prototyped and demonstrated using this modified version of GPS-SDR-SIM to produce simulated GPS signals as well as additional simulated multipath signals. The generated data was processed using a software defined GPS receiver and it was found that the introduction of simulated multipath signals successfully produced the expected characteristics of a composite multipath signal. Further maturation of this work could allow for the development of a GPS receiver testing and evaluation framework and aid in the development of multipath mitigating technologies.

GPS↗

NASA NTRS1975

Experimental test of general relativity using time-delay data from Mariner 6 and Mariner 7

Range and Doppler data from Mariner 6 and Mariner 7 have been analyzed for purposes of measuring the effect of the sun's gravity field on S-band radio transmissions to the spacecraft. The prediction of general relativity, that the round-trip time delays between the station and the spacecraft will be increased by about 200 microsec near superior conjunction, has been verified with an uncertainty of 3 per cent or less. The dominant error source on the experiment is the stochastic nongravitational forces which act on the spacecraft and which limit the accuracy of the determination of the Mariner orbits. Effects of free coronal electrons on the round-trip propagation also make the measurement difficult, but the coronal contribution to the error is only about 1 per cent. Separate analyses of data from Mariner 6 and Mariner 7 yield two values near unity for the parameter gamma* which differ by about 0.3 per cent from each other. This and other considerations suggest that the error in the experiment is perhaps less than 3 per cent.

Anderson, J. D.↗

NASA NTRS1980

Parameter identification of linear discrete stochastic systems with time delays

An identification algorithm that uses the maximum likelihood technique to identify the unknown time delays, plant parameters, and noise covariances of linear discrete stochastic systems is presented. Cases of additive white noise and colored measurement noises are considered. The likelihood function is evaluated using either a minimum-variance (Kalman) filter or a minimal-order observer. The Kalman filter is used in the identification algorithm to provide minimum-variance estimates. The minimal-order observer is a lower-dimensional and computationally simpler filter, and is advantageous especially for systems with long delays. It provides a less optimal solution to the minimum-mean-square state estimation problem. The colored-noise observer algorithm has the disadvantage of having to compute an extra error covariance matrix of lower order.

Wong, E. C.↗

NASA NTRS1982

Investigation of continuously traversing microphone system for mode measurement

The continuously Traversing Microphone System consists of a data acquisition and processing method for obtaining the modal coefficients of the discrete, coherent acoustic field in a fan inlet duct. The system would be used in fan rigs or full scale engine installations where present measurement methods, because of the excessive number of microphones and long test times required, are not feasible. The purpose of the investigation reported here was to develop a method for defining modal structure by means of a continuously traversing microphone system and to perform an evaluation of the method, based upon analytical studies and computer simulated tests. A variety of system parameters were examined, and the effects of deviations from ideal were explored. Effects of traverse speed, digitizing rate, run time, roundoff error, calibration errors, and random noise background level were determined. For constant fan operating speed, the sensitivity of the method to normal errors and deviations was determined to be acceptable. Good recovery of mode coefficients was attainable. Fluctuating fan speed conditions received special attention, and it was concluded that by employing suitable time delay procedures, satisfactory information on mode coefficients can be obtained under realistic conditions. A plan for further development involving fan rig tests was prepared.

Cicon, D. E.↗

NASA NTRS1992

Present status and future prospects for ionospheric propagation corrections for precise time transfer using GPS

The ionosphere can be the greatest variable source of error in precise time transfer using Global Positioning System (GPS) satellites. For single frequency GPS users, the ionospheric correction algorithm can provide an approximate 50 percent r.m.s. correction to the time delay, but users who desire a more complete correction must make actual measurements of ionospheric time delay along the path to the GPS satellite. Fortunately, at least three commercial GPS receivers, specifically designed to measure and correct for ionospheric time delay, are now, or soon will be, available. Initial operation with two different types of GPS ionospheric receivers demonstrated a high degree of accuracy in measuring the ionospheric group delay. Results of these measurements are presented. For those who use a model to correct for ionospheric time delay, it is tempting to use daily values of solar 10.7 cm radio flux to correct a monthly average ionospheric time delay model for each day's operation. The results of correlation of daily maximum ionospheric time delay against solar radio flux values show a poor correlation will be obtained by this procedure. Prospects for improving ionospheric corrections during the declining phase of the present solar cycle are discussed.

Klobuchar, John A.↗

NASA NTRS1987

Measurement of human pilot dynamic characteristics in flight simulation

Fast Fourier Transform (FFT) and Least Square Error (LSE) estimation techniques were applied to the problem of identifying pilot-vehicle dynamic characteristics in flight simulation. A brief investigation of the effects of noise, input bandwidth and system delay upon the FFT and LSE techniques was undertaken using synthetic data. Data from a piloted simulation conducted at NASA Ames Research Center was then analyzed. The simulation was performed in the NASA Ames Research Center Variable Stability CH-47B helicopter operating in fixed-basis simulator mode. The piloting task consisted of maintaining the simulated vehicle over a moving hover pad whose motion was described by a random-appearing sum of sinusoids. The two test subjects used a head-down, color cathode ray tube (CRT) display for guidance and control information. Test configurations differed in the number of axes being controlled by the pilot (longitudinal only versus longitudinal and lateral), and in the presence or absence of an important display indicator called an 'acceleration ball'. A number of different pilot-vehicle transfer functions were measured, and where appropriate, qualitatively compared with theoretical pilot- vehicle models. Some indirect evidence suggesting pursuit behavior on the part of the test subjects is discussed.

Reedy, James T.↗

NASA NTRS2005

Performance Analysis on Fault Tolerant Control System

In a fault tolerant control (FTC) system, a parameter varying FTC law is reconfigured based on fault parameters estimated by fault detection and isolation (FDI) modules. FDI modules require some time to detect fault occurrences in aero-vehicle dynamics. In this paper, an FTC analysis framework is provided to calculate the upper bound of an induced-L(sub 2) norm of an FTC system with existence of false identification and detection time delay. The upper bound is written as a function of a fault detection time and exponential decay rates and has been used to determine which FTC law produces less performance degradation (tracking error) due to false identification. The analysis framework is applied for an FTC system of a HiMAT (Highly Maneuverable Aircraft Technology) vehicle. Index Terms fault tolerant control system, linear parameter varying system, HiMAT vehicle.

Shin, Jong-Yeob↗