Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “contact pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Development of mainshaft seals for advanced air breathing propulsion systems

A gas-film face seal design incorporating shrouded Rayleigh step lift pads at the primary sealing face was analyzed for performance over a wide range of gas turbine engine conditions. Acceptable leakage rates and operation without rubbing contact was predicted for engine conditions that included sealed pressures to 500 psi, sliding speeds to 600 ft/sec, and sealed gas temperatures to 1200 F. In the experimental evaluation, measured gas leakage rates were, in general, close to that predicted and sometimes lower. Satisfactory performance of the gas-film seal was demonstrated at the maximum seal seat axial runout expected in present positive contact face seal applications. Stable operation was shown when testing was performed with air-entrained dirt.

Dobek, L. J.↗
DOE OSTI2021

Effect of workpiece curvature on the tool influence function during hemispherical sub-aperture tool glass polishing

The influence of workpiece curvature on the tool influence function spot during polishing of fused silica glass with cerium oxide slurry, while using a rotating hemispherical pad-foam tool for a wide variety of process conditions (tool displacement, inclination angle, and rotation rate), has been investigated. (Workpiece curvature ranged from 500 mm radius concave to 43 mm radius convex.) The TIF spot decreases in diameter and increases in the peak removal rate on more convex workpieces. In contrast, the TIF spot increases both in diameter and peak removal rate on more concave workpieces. For the range of workpiece curvatures investigated, both the spot size and the peak removal rate changed significantly, as much as 2 times. An elastic sphere–sphere contact mechanics model, which utilizes both a modified displacement (that leads to a change in the applied load) as well as a mismatch factor (that influences the pressure distribution shape), has been developed. Furthermore, the model was validated using both offline load-displacement measurements and finite-element analysis simulations. The model quantitatively describes the measured change in the relative contact diameter and relative pressure distribution, as well as semiquantitively describes the change in the relative volumetric removal rate on a large variety of TIF spots. The change in the volumetric removal rate for convex workpieces is a result of the balance between a decreasing spot size (reducing removal) and an increasing peak pressure (increasing removal), which usually results in relatively small changes in volumetric removal. In the case of concave workpieces, the volumetric removal rate change is also governed by a similar balance, but the spot size increase contribution dominates, resulting in a significant increase in volumetric removal rate. Understanding these trends can enable methods to add greater determinism during the fabrication of freeform optics by adjusting polishing parameters (such as dwell time) while the tool translates along a workpiece surface with different local curvatures.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Vapor detection and vapor pressure measurements of fentanyl and fentanyl hydrochloride salt at ambient temperatures

There is a need for non-contact, real-time vapor detection of drugs to combat illicit transportation and help curb the opioid epidemic. The low-volatility of drugs, like fentanyl, makes room temperature vapor detection of illicit drugs challenging, but feasible by atmospheric flow tube-mass spectrometry (AFT-MS). AFT-MS is a non-contact vapor detection approach capable of ultra-trace detection of drugs, including fentanyl and its analogs at low parts-per-quadrillion (ppqv) levels. The determination of vapor pressure values of fentanyl is necessary to understand potential vapor concentrations that may be available for detection. In this paper, vapor pressures of fentanyl free base and fentanyl hydrochloride salt (a common form of the illicit drug) were measured as a function of temperature at or near ambient conditions using the transpiration (gas saturation) method and AFT-MS. Based on our measurements, the vapor pressure of fentanyl at 25 °C is 9.0 × 10-14 atm (90 ppqv), and the vapor pressure of fentanyl hydrochloride at 25 °C is 1.8 x 10-17 atm (0.018 ppqv). We also demonstrate non-contact, real-time vapor detection of fentanyl. Preconcentration of vapors can further extend the detection capabilities. The collection, desorption, and detection of fentanyl vapors at ambient conditions was demonstrated for sampling times of seconds to an hour resulting in increased signal. AFT-MS is a viable detection method of fentanyl and other drugs for screening of packages and cargo.

atmospheric flow tube-mass spectrometry (AFT-MS), ↗
NASA NTRS1991

An improved compression molding technology for continuous fiber reinforced composite laminate. Part 1: AS-4/LaRC-TPI 1500 (HFG) Prepreg system

Poor processability of fiber reinforced high performance polyimide thermoplastic resin composites is a well recognized issue which, in many cases, prohibits the fabrication of composite parts with satisfactorily consolidated quality. Without modifying the resin matrix chemistry, improved compression modeling procedures were proposed and investigated with the AS-4/LaRC-TPI 1500 High Flow Grade (HFG) prepreg system. Composite panels with excellent C-scans can be consistently molded by this method under 700 F and a consolidation pressure as low as 100 psi. A mechanism for the consolidation of the composite under this improved molding technique is discussed. This mechanism reveals that a certain degree of matrix shear and tow filament slippage and nesting between plies occur during consolidation, which leads to a reduction of the consolidating pressure necessary to offset the otherwise intimate inter fiber-fiber contact and consequently achieves a better consolidation quality. Outstanding short beam shear strength and flexural strength were obtained from the molded panels. A prolonged consolidation step under low pressure, i.e., 100 psi at 700 F for 75 minutes, was found to significantly enhance the composite mechanical properties.

Hou, Tan-Hung↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. 4: Starvation results

The influence of lubricant starvation on minimum film thickness was investigated by moving the inlet boundary closer to the contact center. The following expression was derived for the dimensionless inlet distance at the boundary between the fully flooded and starved conditions: m* = 1 + 3.06 ((R/b)(R/b)H) to the power 0.58, where R is the effective radius of curvature, b is the semiminor axis of the contact ellipse, and H is the central film thickness for fully flooded conditions. A corresponding expression was also given based on the minimum film thickness for fully flooded conditions. Therefore, for m m*, starvation occurs and, for m m*, a fully flooded condition exists. Two other expressions were also derived for the central and minimum film thicknesses for a starved condition. Contour plots of the pressure and the film thickness in and around the contact are shown for the fully flooded and starved lubricating conditions, from which the film thickness was observed to decrease substantially as starvation increases.

Hamrock, B. J.↗
NASA NTRS1978

Surface temperatures and glassy state investigations in tribology, part 1

The research in this report is divided into two categories: (1) lubricant rheological behavior, and (2) thermal behavior of a simulated elastohydrodynamic contact. The studies of the lubricant rheological behavior consists of high pressure, low shear rate viscosity measurements, viscoelastic transition measurements, by volume dilatometry, dielectric transitions at atmospheric pressure and light scattering transitions. Lubricant shear stress-strain behavior in the amorphous glassy state was measured on several fluids. It appears clear from these investigations that many lubricants undergo viscoplastic transitions in typical EHD contacts and that the lubricant has a limiting maximum shear stress it can support which in turn will determine the traction in the contact except in cases of very low slide-roll ratio. Surface temperature measurements were made for a naphthenic mineral oil and a polyphenyl ether. The maximum surface temperature in these experiments was approximately symmetrical about the zero slide-roll ration except for absolute values of slide-roll ratio greater than about 0.9. Additional surface temperature measurements were made in contacts with rough surfaces where the composite surface roughness was approximately equal to the EHD film thickness. A regression analysis was done to obtain a predictive equation for surface temperatures as a function of pressure, sliding speed, and surface roughness. A correction factor for surface roughness effects to the typical flash temperature analysis was found.

Winer, W. O.↗
NASA NTRS1980

Effects of varying oxygen partial pressure on molten silicon-ceramic substrate interactions

The silicon sessile drop contact angle was measured on hot pressed silicon nitride, silicon nitride coated on hot pressed silicon nitride, silicon carbon coated on graphite, and on Sialon to determine the degree to which silicon wets these substances. The post-sessile drop experiment samples were sectioned and photomicrographs were taken of the silicon-substrate interface to observe the degree of surface dissolution and degradation. Of these materials, silicon did not form a true sessile drop on the SiC on graphite due to infiltration of the silicon through the SiC coating, nor on the Sialon due to the formation of a more-or-less rigid coating on the liquid silicon. The most wetting was obtained on the coated Si3N4 with a value of 42 deg. The oxygen concentrations in a silicon ribbon furnace and in a sessile drop furnace were measured using the protable thoria-yttria solid solution electrolyte oxygen sensor. Oxygen partial pressures of 10 to the minus 7 power atm and 10 to the minus 8 power atm were obtained at the two facilities. These measurements are believed to represent nonequilibrium conditions.

Ownby, D. P.↗
DOE OSTI2023

Manufacturing Water‐Based Low‐Tortuosity Electrodes for Fast‐Charge through Pattern Integrated Stamping

Achieving high energy density and fast charging of lithium‐ion batteries can accelerate the promotion of electric vehicles. However, the increased mass loading causes poor charge transfer, impedes the electrochemical reaction kinetics, and limits the battery charging rate. Herein, this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode, which benefits ion transport and increases the rate performance of the electrode. Meanwhile, the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode. Compared to the conventional bar‐coated electrode with the same thickness of 155 μm (delivered a discharge capacity of 16 mAh g −1 at the rate of 3 C), the stamped low‐tortuosity LiFePO 4 electrode delivered 101 mAh g −1 capacity. Additionally, water was employed as a solvent in this study. Owing to its eco‐friendliness, high scalability, and minimal waste generation, this novel stamping technique inspire a new method for the industrial‐level efficient roll to roll fabrication of fast‐charge electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Thermo-hydrologic processes in maar eruptions: The role of vapor transport and condensation

Phreatomagmatic eruptions occur when magma interacts directly with water or slurries, commonly from groundwater in the shallow crust, resulting in rapid conversion of thermal energy to mechanical energy in a set of processes known as molten fuel-coolant interaction (MFCI). The efficiency of MFCI is controlled by properties of the magma and coolant, contact surface geometry, and system conditions, such as pressure and temperature; phreatomagmatic behavior can range from passive thermal granulation to violent thermohydraulic explosions (Zimanowski et al., 2015). Maar-diatreme eruptions, characterized by repetitive phreatomagmatic explosions, can form in a wide range of near-surface environments, from soft sediment substrate (e.g., Tecuitlapa, Mexico, Ort and Carrasco-Núñez, 2009; Hopi Buttes, AZ, Lefebvre et al., 2013) to hard, fractured country rock (e.g., West Eifel volcanic field, Germany and Massif Central, France, Lorenz, 2003). Country-rock structure, including faults and joints, rock type, and shallow crustal hydrologic properties, can influence an eruption’s behavior by controlling how much and at what rate water can be supplied to the magma (hydraulic flow rate), and determining the sediment: water ratio in the case of soft-sediment substrate eruptions. In a “soft” substrate environment, volcanic tremor can lead to liquefaction of saturated sediment, producing a slurry that may then interact with magma in unique ways (White, 1996; Auer, et al., 2006).

58 GEOSCIENCES↗
DOE OSTI2024

Flexible operation of nuclear hybrid energy systems for load following and water desalination

Nuclear hybrid energy systems (NHES) have the potential to provide dependable and emission-free electricity to the grid while also increasing the flexibility and reliability of the electrical grid. Molten salt reactor (MSR) technology can provide consistent, carbon-free electricity while also increasing efficiency, security, and sustainability and reducing nuclear waste. This study investigates the integration of Molten Salt Reactors (MSR) and conventional Pressurized Water Reactors (PWR) with desalination technologies: Direct Contact Membrane Distillation (DCMD), Multi-Stage Flash Distillation (MSFD), and Reverse Osmosis (RO). Dynamic first-principles models were developed and tested using real grid data from the New York Independent System Operator. The results demonstrate that nuclear power is capable of flexibly responding to changing grid demand while simultaneously producing clean water, particularly during periods of low electricity demand. The MSR-RO system was found to be the most efficient in electricity generation and water production, and all hybrid systems reduced CO2 emissions by 356,000 to 682,000 tons annually. Economic analysis reveals that nuclear desalination technologies are cost-competitive with conventional systems, especially when paired with RO. Finally, these findings confirm the technical feasibility and environmental benefits of nuclear hybrid systems for sustainable electricity and water production.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Developing a model for the impact of non-conformal lithium contact on electro-chemo-mechanics and dendrite growth

Lithium dendrite growth hinders the use of lithium metal anodes in commercial batteries. We present a 3D model to study the mechanical and electrochemical mechanisms that drive microscale plating. With this model, we investigate electrochemical response across a lithium protrusion characteristic of rough anode surfaces, representing the separator as a porous polymer in non-conformal contact with a lithium anode. The impact of pressure on separator morphology and electrochemical response is of particular interest, as external pressure can improve cell performance. We explore the relationships between plating propensity, stack pressure, and material properties. External pressure suppresses lithium plating due to interfacial stress and separator pore closure, leading to inhomogeneous plating rates. For moderate pressures, dendrite growth is completely suppressed, as plating will occur in the electrolyte-filled gaps between anode and separator. In fast-charging conditions and systems with low electrolyte diffusivities, the benefits of pressure are overridden by ion transport limitations.

25 ENERGY STORAGE↗
DOE OSTI2020

Spatially resolved absolute densities of reactive species and positive ion flux in He-O 2 RF-driven atmospheric pressure plasma jet: touching and non-touching with dielectric substrate

Atmospheric pressure plasma jets (APPJs) are operating in direct contact with dielectric substrates for many applications. Nonetheless, many studies have been focusing on free jets. In this letter, we report spatially resolved measurements of reactive species including neutral and ionic species in an He + 1% O 2 RF-driven APPJ by molecular beam mass spectrometry equipped with a dielectric sampling plate, enabling to detect species densities for APPJ operating remotely or in direct contact with a substrate. Here, the spatially resolved distribution of O, O 2 (a 1 Δ g ) and O 3 is dominated by convection and, remarkably, shows minimum differences between touching and non-touching conditions.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS1973

Elastohydrodynamic analysis using a power law pressure-viscosity relation

An isothermal elastohydrodynamic (EHD) inlet analysis of the Grubin type which considers a power law pressure-viscosity relation and a finite pressure at the inlet edge of the Hertzian contact zone was performed. Comparisons made with published X-ray EHD film thickness data for a synthetic paraffinic oil and when conventional EHD theory showed that the present theory exhibits a slightly stronger film thickness load dependence than do previous isothermal EHD theories but far less than that exhibited by the measured data.

Loewenthal, S. H.↗
NASA NTRS1978

Postural illusions experienced during Z-axis recumbent rotation and their dependence upon somatosensory stimulation of the body surface

A blindfolded recumbent subject experiences a variety of postural illusions when rotated about his Z axis. Initially, during the acceleratory phase of rotation, turning about his Z axis is experienced; but, as rotary velocity increases, a spiraling of the body outward in the direction opposite to true rotation is experienced as well. Above 15-20 rpm, only orbital motion of the body is experienced, with the subject feeling that he is always facing in the same direction. One cycle of the apparent orbit is completed each time the subject actually rotates 360 deg. The reverse sequence of illusory motion is experienced during deceleration. The illusory motion all subjects experience during Z-axis recumbent rotation is shown to depend upon the touch and pressure stimulation of the body surface generated by contact forces of support.

Lackner, J. R.↗