SEARCH · Engineering Papers

Results for “circular data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1961

Analog Simulation of a Pilot-Controlled Rendezvous

The rendezvous of a pilot-controlled space ferry vehicle with an orbiting space station was simulated in six degrees of freedom. A fixed-base simulator and an analog computer were used. The ferry vehicle was assumed to have a single main thrusting rocket and to be provided with attitude control. Control of the thrust was provided by a rocket throttle quadrant which could provide either proportional or on-off control. The attitude of the vehicle was controlled during the rendezvous with a two-axis, pencil-type side-arm controller and rudder pedals. For the most part rendezvous maneuvers were made with the target satellite in a circular orbit. In addition, an elliptical station orbit was investigated. Tolerable initial conditions, as well as adequate data presentations, were determined. Results of the investigation indicate that a human pilot can rendezvous successfully with the vehicle and instrumentation considered over a wide band of initial conditions. Coplanar conditions are not necessary. Retro-rocket fuel used is not greatly increased by imposing perturbing influences such as rocket-misalignment torques on the rendezvous vehicle. When excessive attitude-control torques are required to maintain the necessary trim attitudes under misalignment influences, the reaction fuel used for this control increases. The time required for a specific rendezvous varies somewhat between pilots. If control of the time for completing the rendezvous is desired, requirements for retrorocket fuel are affected, and an energy-management schedule is required. Continuous variation of the thrust is not necessary. The pilot positions the throttle to obtain a desired level of thrust, and applies bursts of thrust as required. All data were presented on dialed instruments. The quantities required are range and range rate and line-of-sight rates between the vehicle and the station, vehicle attitudes and angular rates, and the angles subtended by the line of sight. For the equipment assumed herein, satellite rendezvous presented no great problem to the pilot.

Brissenden, Roy F.↗

NASA NTRS2004

Full-duplex optical communication system

A method of full-duplex electromagnetic communication wherein a pair of data modulation formats are selected for the forward and return data links respectively such that the forward data electro-magnetic beam serves as a carrier for the return data. A method of encoding optical information is used wherein right-hand and left-hand circular polarizations are assigned to optical information to represent binary states. An application for an earth to low earth orbit optical communications system is presented which implements the full-duplex communication and circular polarization keying modulation format.

Shay, Thomas M.↗

NASA NTRS2016

Low-Amplitude Topographic Features and Textures on the Moon: Initial Results from Detrended Lunar Orbiter Laser Altimeter (LOLA) Topography

Global lunar topographic data derived from ranging measurements by the Lunar Orbiter Laser Altimeter (LOLA) onboard LRO mission to the Moon have extremely high vertical precision. We use detrended topography as a means for utilization of this precision in geomorphological analysis. The detrended topography was calculated as a difference between actual topography and a trend surface defined as a median topography in a circular sliding window. We found that despite complicated distortions caused by the non-linear nature of the detrending procedure, visual inspection of these data facilitates identification of low-amplitude gently-sloping geomorphic features. We present specific examples of patterns of lava flows forming the lunar maria and revealing compound flow fields, a new class of lava flow complex on the Moon. We also highlight the identification of linear tectonic features that otherwise are obscured in the images and topographic data processed in a more traditional manner.

Moon↗

NASA NTRS1988

Comparison of circular orbit and Fourier power series ephemeris representations for backup use by the upper atmosphere research satellite onboard computer

The Upper Atmosphere Research Satellite (UARS) is a three-axis stabilized Earth-pointing spacecraft in a low-Earth orbit. The UARS onboard computer (OBC) uses a Fourier Power Series (FPS) ephemeris representation that includes 42 position and 42 velocity coefficients per axis, with position residuals at 10-minute intervals. New coefficients and 32 hours of residuals are uploaded daily. This study evaluated two backup methods that permit the OBC to compute an approximate spacecraft ephemeris in the event that new ephemeris data cannot be uplinked for several days: (1) extending the use of the FPS coefficients previously uplinked, and (2) switching to a simple circular orbit approximation designed and tested (but not implemented) for LANDSAT-D. The FPS method provides greater accuracy during the backup period and does not require additional ground operational procedures for generating and uplinking an additional ephemeris table. The tradeoff is that the high accuracy of the FPS will be degraded slightly by adopting the longer fit period necessary to obtain backup accuracy for an extended period of time. The results for UARS show that extended use of the FPS is superior to the circular orbit approximation for short-term ephemeris backup.

Kast, J. R.↗

NASA NTRS1983

Windward fraction of the total mass or heat transport for flow past a circular cylinder

The windward fraction of the total mass or heat transport for flow past a cylindrical aerodynamic object was estimated using the available experimental data for the angular distribution of the Nusselt transfer coefficient, Nu(theta, Re). The Re dependence of the windward surface fraction was calculated for the values of Re between 2 and 400,000. The results obtained from polar integrations of data from eight sources indicate that, for Reynolds numbers up to about 2000, more than 70 percent of the total transfer occurs on the windward surface. For the Re values above 100,000, the windward percentage is less than 50 percent.

Gokoglu, S.↗

NASA NTRS1979

Lunar physical properties from analysis of magnetometer data

The electromagnetic properties of the lunar interior are discussed with emphasis on (1) bulk, crustal, and local anomalous conductivity; (2) bulk magnetic permeability measurements, iron abundance estimates, and core size limits; (3) lunar ionosphere and atmosphere; and (4) crustal magnetic remanence: scale size measurements and constraints on remanence origin. Appendices treat the phase relationship between the energetic particle flux modulation and current disc penetrations in the Jovian magnetosphere (Pioneer 10 inbound) theories for the origin of lunar magnetism; electrical conductivity anomalies associated with circular lunar maria; electromagnetic properties of the Moon; Mare Serenitatis conductivity anomaly detected by Apollo 16 and Lunokhod 2 magnetometers; and lunar properties from magnetometer data: effects of data errors.

Daily, W. D.↗

NASA NTRS1977

Updated dispersion analysis for the first Orbital Flight Test (OFT-1) mission

A dispersion analysis considering 3-sigma uncertainties (or perturbations) in platform, vehicle, and environmental parameters was performed for the first orbital flight test (OFT-1) mission. The dispersion analysis is based on the nominal trajectory for the OFT-1 reference flight profile and was performed to determine state vector and performance dispersions (or variations) which result from the indicated 3 sigma uncertainties. The dispersions are determined at major mission events and fixed times from liftoff (time slices). Principal error contributors to the covariance matrix are listed. The dispersion data indicates that the largest position error occurs in the down range component. At main engine cutoff and circularization, the vehicle performance uncertainties are the major contributors to down range error.

Snow, L. S.↗

NASA NTRS1981

Receiving signals of any polarization

Two-channel detection accomodates linear, circular, and elliptical polarization in one receiving unit. Receiver employs orthomode transducer which breaks any type signal into one left and one right circular component. These are processed in separate receiver channels with equal time-delay, and then recombined for data extraction. System eliminates losses due to polarization mismatch.

Ohlson, J. E.↗

NASA NTRS1983

X-ray and microwave observations of active regions

Coordinated high-resolution (1-3 arcsec) observations of two active solar regions (H 421 and H 419) on November 16, 1979, are reported: soft-X-ray filtergrams from a sounding rocket flight, VLA total-intensity and circular-polarization microwave (6-cm) radio maps, KPNO full-disk photospheric magnetograms, and BBSO H-alpha data. The images were converted to 4.8-arcsec/mm-scale transparencies and coaligned on the basis of sunspot positions for comparison. The two active regions are characterized in detail, and intensity, size, and polarization data for the brightest microwave components (BMC) are listed. It is found that 19 of the 32 BMC are farther than 5 arcsec from any sunspot, and that X-ray-emitting structures only rarely correspond to sunspots, or BMC. About one third of the BMC are located at the feet or legs of coronal loops smaller than about 50,000 km. The limitations implied by these obervations for proposed thermal-bremsstrahlung, thermal-gyro-resonance, and nonthermal microwave-emission mechanisms are discussed.

Webb, D. F.↗

NASA NTRS1987

Analysis of crossover between local and massive separation on airfoils

The occurrence of massive separation on airfoils operating at high Reynolds number poses an important problem to the aerodynamicist. In the present study, the phenomenon of crossover, induced by airfoil thickness, between local separation and massive separation is investigated for low speed (incompressible), symmetric flow past realistic airfoil geometries. This problem is studied both for the infinite Reynolds number asymptotic limit using triple-deck theory and for finite Reynolds number using interacting boundary-layer theory. Numerical results are presented which illustrate how the flow evolves from local to massive separation as the airfoil thickness is increased. The results of the triple-deck and the interacting boundary-layer analyses are found to be in qualitative agreement for the NACA four digit series and an uncambered supercritical airfoil. The effect of turbulence on the evolution of the flow is also considered. Solutions are presented for turbulent flows past a NACA 0014 airfoil and a circular cylinder. For the latter case, the calculated surface pressure distribution is found to agree well with experimental data if the proper eddy pressure level is specified.

Barnett, Mark↗

NASA NTRS1989

The measurement of boundary layers on a compressor blade in cascade. Volume 1: Experimental technique, analysis and results

Measurements were made of the boundary layers and wakes about a highly loaded, double-circular-arc compressor blade in cascade. These laser Doppler velocimetry measurements have yielded a very detailed and precise data base with which to test the application of viscous computational codes to turbomachinery. In order to test the computational codes at off-design conditions, the data were acquired at a chord Reynolds number of 500,000 and at three incidence angles. Moreover, these measurements have supplied some physical insight into these very complex flows. Although some natural transition is evident, laminar boundary layers usually detach and subsequently reattach as either fully or intermittently turbulent boundary layers. These transitional separation bubbles play an important role in the development of most of the boundary layers and wakes measured in this cascade and the modeling or computing of these bubbles should prove to be the key aspect in computing the entire cascade flow field. In addition, the nonequilibrium turbulent boundary layers on these highly loaded blades always have some region of separation near the trailing edge of the suction surface. These separated flows, as well as the subsequent near wakes, show no similarity and should prove to be a challenging test for the viscous computational codes.

Zierke, William C.↗

NASA NTRS1992

Analysis of thermo-chemical nonequilibrium models for carbon dioxide flows

The aerothermodynamics of thermochemical nonequilibrium carbon dioxide flows is studied. The chemical kinetics models of McKenzie and Park are implemented in separate three-dimensional computational fluid dynamics codes. The codes incorporate a five-species gas model characterized by a translational-rotational and a vibrational temperature. Solutions are obtained for flow over finite length elliptical and circular cylinders. The computed flowfields are then employed to calculate Mach-Zehnder interferograms for comparison with experimental data. The accuracy of the chemical kinetics models is determined through this comparison. Also, the methodology of the three-dimensional thermochemical nonequilibrium code is verified by the reproduction of the experiments.

Rock, Stacey G.↗

NASA NTRS1994

Automatic commanding of the Mars Observer Camera

Mars Observer, launched in September 1992, was intended to be a 'survey-type' mission that acquired global coverage of Mars from a low, circular, near-polar orbit during an entire Martian year. As such, most of its instruments had fixed data rates, wide fields of view, and relatively low resolution, with fairly limited requirements for commanding. An exception is the Mars Observer Camera, or MOC. The MOC consists of a two-color Wide Angle (WA) system that can acquire both global images at low resolution (7.5 km/pixel) and regional images at commandable resolutions up to 250 m/pixel. Complementing the WA is the Narrow Angle (NA) system, that can acquire images at 8 resolutions from 12 m/pixel to 1.5 m/pixel, with a maximum crosstrack dimension of 3 km. The MOC also provides various forms of data compression (both lossless and lossy), and is designed to work at data rates from 700 bits per second (bps) to over 80k bps. Because of this flexibility, developing MOC command sequences is much more difficult than the routine mode-changing that characterizes other instrument operations. Although the MOC cannot be pointed (the spacecraft is fixed nadir-pointing and has no scan platform), the timing, downlink stream allocation, compression type and parameters, and image dimensions of each image must be commanded from the ground, subject to the constraints inherent in the MOC and the spacecraft. To minimize the need for a large operations staff, the entire command generation process has been automated within the MOC Ground Data System. Following the loss of the Mars Observer spacecraft in August 1993, NASA intends to launch a new spacecraft, Mars Global Surveyor (MGS), in late 1996. This spacecraft will carry the MOC flight spare (MOC 2). The MOC 2 operations plan will be largely identical to that developed for MOC, and all of the algorithms described here are applicable to it.

Caplinger, Michael↗

NASA NTRS2000

The Strategy for the Second Phase of Aerobraking Mars Global Surveyor

On February 19, 1999, the Mars Global Surveyor (MGS) spacecraft was able to propulsively establish its mapping orbit. This event followed the completion of the second phase of aerobraking for the MGS spacecraft on February 4, 1999. For the first time, a spacecraft at Mars had successfully employed aerobraking methods in order to reach its desired pre-launch mapping orbit. This was accomplished despite a damaged spacecraft solar array. The MGS spacecraft was launched on November 7, 1996, and after a ten month interplanetary transit was inserted into a highly elliptical capture orbit at Mars on September 12, 1997. Unlike other interplanetary missions, the MGS spacecraft was launched with a planned mission delta-V ((Delta)V) deficit of nearly 1250 m/s. To overcome this AV deficit, aerobraking techniques were employed. However, damage discovered to one of the spacecraft's two solar arrays after launch forced major revisions to the original aerobraking planning of the MGS mission. In order to avoid a complete structural failure of the array, peak dynamic pressure levels for the spacecraft were established at a major spacecraft health review in November 1997. These peak dynamic pressure levels were roughly one-third of the original mission design values. Incorporating the new dynamic pressure limitations into mission replanning efforts resulted in an 'extended' orbit insertion phase for the mission. This 'extended' orbit insertion phase was characterized by two distinct periods of aerobraking separated by an aerobraking hiatus that would last for several months in an intermediate orbit called the "Science Phasing Orbit" (SPO). This paper describes and focuses on the strategy for the second phase of aerobraking for the MGS mission called "Aerobraking Phase 2." This description will include the baseline aerobraking flight profile, the trajectory control methodology, as well as the key trajectory metrics that were monitored in order to successfully "guide' the spacecraft to its desired mapping orbit. Additionally, the actual aerobraking progress is contrasted to the planned aerobraking flight profile. (A separate paper will describe the navigation aspects of MGS aerobraking in detail.) Key to the success of the MGS mission is the delivery of the spacecraft to its final mapping orbit and the synergy the instrument complement provides to its scientific investigators when science data is returned from that orbit. The MGS mapping orbit is characterized as a low altitude, near-circular, near-polar orbit that is Sun-synchronous with the descending equatorial crossing at 2:00 AM local mean solar time (LMST).

Johnston, M. D.↗

NASA NTRS1999

Effects of Hot Streak Shape on Rotor Heating in a High-Subsonic Single-Stage Turbine

Experimental data have shown that combustor temperature non-uniformities can lead to the excessive heating of first-stage rotor blades in turbines. This heating of the rotor blades can lead to thermal fatigue and degrade turbine performance. The results of recent studies have shown that variations in the circumferential location (clocking) of the hot streak relative to the first-stage vane airfoils can be used to minimize the adverse effects of the hot streak. The effects of the hot streak/airfoil count ratio on the heating patterns of turbine airfoils have also been evaluated. In the present investigation, three-dimensional unsteady Navier-Stokes simulations have been performed for a single-stage high-pressure turbine operating in high subsonic flow. In addition to a simulation of the baseline turbine, simulations have been performed for circular and elliptical hot streaks of varying sizes in an effort to represent different combustor designs. The predicted results for the baseline simulation show good agreement with the available experimental data. The results of the hot streak simulations indicate: that a) elliptical hot streaks mix more rapidly than circular hot streaks, b) for small hot streak surface area the average rotor temperature is not a strong function of hot streak temperature ratio or shape, and c) hot streaks with larger surface area interact with the secondary flows at the rotor hub endwall, generating an additional high temperature region.

Dorney, Daniel J.↗

NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise.

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 ft/sec. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise.

Olsen, W. A.↗

NASA NTRS1974

Spinning mode sound propagation in ducts with acoustic treatment

Recent acoustic data have shown larger noise attenuations than predicted for acoustically treated aircraft engine inlets without splitter rings. These data have stimulated a more detailed theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts. In addition, the suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. The theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. It is found that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number. For annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. The results help explain why suppressors with splitter rings have been quite effective in spite of the lack of detailed information on the noise-source modal structure. Conversely, effective use of outer-wall treatment alone will require expanded knowledge of the noise-source structure. Approximate solutions are presented to help interpret the more exact theoretical results.

Rice, E. J.↗

NASA NTRS1976

Requirements and capabilities for planetary missions. Volume 2: Mars polar orbiter penetrator 1981

The Mars Polar Orbiter/Penetrator 1981 mission, intended to investigate the manner in which Mars has evolved, and which surveys its geochemistry, performs climatological investigations, and attempts to determine the planet's gravitational field, was described. The spacecraft, modified from the Viking Orbiter design, carries a new remote-sensing payload and six penetrators. The penetrators are released from a 2.46-h, 1000-km sun synchronous circular orbit and interrogated daily throughout the 2-year orbital mission. X-band telemetry is used to increase data return.

Ball, G. G.↗