SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrical, mechanical, and operational aspects of a test cell assembly for studying rotating fluids with a free surface are described. Results of a stress analysis prepared to document the structural adequacy for safe use on the KC-135 aircraft are presented along with results of a single load proof test of the most critical load case. Engineering drawings are included.
A new firefly luciferase bioluminescence assay method that differentiates free extracellular ATP (dead cells, etc.) from intracellular ATP (viable microbes) was used to determine the viable microbial cleanliness of various clean-room facilities. For comparison, samples were taken from both clean-rooms, where the air was filtered to remove particles >0.5 microm, and ordinary rooms with unfiltered air. The intracellular ATP was determined after enzymatically degrading the sample's free ATP. Also for comparison, cultivable microbial populations were counted on nutrient-rich trypticase soy agar (TSA) plates. Both the cultivable and ATP-based determinations indicate that the microbial burden was lower in clean-room facilities than in ordinary rooms. However, there was no direct correlation between the two sets of measurements because the two assays measured very different populations. A large fraction of the samples yielded no colony formers on TSA, but were positive for intracellular ATP. Subsequently, genomic DNA was isolated directly from selected samples and 16S rDNA fragments were cloned and sequenced, identifying nearest neighbors, many of which are known to be noncultivable in the media employed. It was concluded that viable microbial contamination can be reliably monitored by measurement of intracellular ATP, and that this method may be considered superior to cultivable colony counts due to its speed and its ability to report the presence of viable but noncultivable organisms. When the detection of nonviable microbes is of interest, the ATP assay can be supplemented with DNA analysis.
The observed steep kinetic scale turbulence spectrum in the solar wind raises the question of how that turbulence originates. Observations of keV energetic electrons during solar quiet time suggest them as a possible source of free energy to drive kinetic turbulence. Using particle-in-cell simulations, we explore how the free energy released by an electron two-stream instability drives Weibel-like electromagnetic waves that excite wave-wave interactions. Consequently, both kinetic Alfvénic and whistler turbulence are excited that evolve through inverse and forward magnetic energy cascades.
The ionomer content in platinum group metal (PGM)-free polymer electrolyte fuel cell (PEFC) cathode catalyst layer (CCL) plays an important role in the electrode gas transport properties, proton conductivity, and hence, membrane electrode assembly (MEA) performance. In this work, the ionomer content in the CCL is varied, influencing electrode microstructure by altering porosity, tortuosity, as well as ionomer distribution and coverage of the catalyst particles. A novel technique consisting of a H 2 pump, combined with a Pt black sensor layer, is used to measure the bulk mass transport resistance of a series of PGM-free CCL prepared with different ionomer contents. The values for bulk electrode mass transport resistance are contrasted with electrode proton transport resistance in the cathode catalyst layer, establishing a clearly defined trade-off between two key performance limiting phenomena and identifying a need for novel PGM-free electrode fabrication strategies.
Elemental boron exists in multiple allotropes, each characterized by structures containing icosahedral subunits. These structures have interstitial sites between the icosahedral subunits that are partially occupied. The number of atoms in the unit cell varies depending on the occupancy of these interstitial sites. Here we have investigated the thermodynamic stability of boron allotropes for different numbers of atoms in the unit cell by calculating the free energies, including the contribution of phonons. It has been found that β-rhombohedral boron is most stable with 107 atoms/cell at low temperatures, while it becomes most stable with 105 atoms/cell above 1700 K. This suggests the occurrence of a phase transition at this temperature, which could account for the large variation in the number of atoms in the unit cell for β-rhombohedral boron samples. α-tetragonal boron is consistently most stable with 52 atom/cell and becomes unstable with more than 52 atoms/cell. Similar to β-rhombohedral boron, β-tetragonal boron may undergo a phase transition between 192 and 190 atoms/cell configurations. However, the thermodynamic stability of pure β-tetragonal boron has been questioned in comparison with other allotropes.
Prolonged spaceflight causes degeneration of skeletal tissue with incomplete recovery even after return to Earth. We hypothesize that heavy-ion irradiation, a component of Galactic Cosmic Radiation, damages osteoblast progenitors and may contribute to bone loss during long duration space travel beyond the protection of the Earth's magnetosphere. Male, 16 week-old C57BL6/J mice were exposed to high-LET (56-Fe, 600MeV) radiation using either low (5 or 10cGy) or high (50 or 200cGy) doses at the NASA Space Radiation Lab and were euthanized 3-4, 7, or 35 days later. Bone structure was quantified by microcomputed tomography (6.8 μm pixel size) and marrow cell redox assessed using membrane permeable, free radical-sensitive fluorogenic dyes. To assess osteoblastogenesis, adherent marrow cells were cultured ex vivo, then mineralized nodule formation quantified by imaging and gene expression analyzed by RT-PCR. Interestingly, 3-4 days post-exposure, fluorogenic dyes that reflect cytoplasmic generation of reactive nitrogen/oxygen species (DAF-FM Diacetate or CM-H2DCFDA) revealed irradiation (50cGy) reduced free radical generation (20-45%) compared to sham-irradiated controls. Alternatively, use of a dye showing relative specificity for mitochondrial superoxide generation (MitoSOX) revealed an 88% increase compared to controls. One week after exposure, reactive oxygen/nitrogen levels remained lower (24%) relative to sham-irradiated controls. After one month, high dose irradiation (200 cGy) caused an 86% decrement in ex vivo nodule formation and a 16-31% decrement in bone volume to total volume and trabecular number (50, 200cGy) compared to controls. High dose irradiation (200cGy) up-regulated expression of a late osteoblast marker (BGLAP) and select genes related to oxidative metabolism (Catalase) and DNA damage repair (Gadd45). In contrast, lower doses (5, 10cGy) did not affect bone structure or ex vivo nodule formation, but did down-regulate iNOS by 0.54-0.58 fold. Thus, both low- and high-doses of heavy-ion irradiation cause time-dependent, adaptive changes in redox state within marrow cells but only high doses (50, 200cGy) inhibit osteoblastogenesis and cause cancellous bone loss. We conclude space radiation has the potential to cause persistent damage to bone marrow-derived stem and progenitor cells for osteoblasts despite adaptive changes in cellular redox state.
The seasonal cycle of surface albedo of sea ice in the Arctic is estimated from measurements made with the Advanced Very High Resolution Radiometer (AVHRR) on the polar-orbiting satellites NOAA-10 and NOAA-11. The albedos of 145 200-km-square cells are analyzed. The cells are from March through September 1989 and include only those for which the sun is more than 10 deg above the horizon. Cloud masking is performed manually. Corrections are applied for instrument calibration, nonisotropic reflection, atmospheric interference, narrowband to broadband conversion, and normalization to a common solar zenith angle. The estimated albedos are relative, with the instrument gain set to give an albedo of 0.80 for ice floes in March and April. The mean values for the cloud-free portions of individual cells range from 0.18 to 0.91. Monthly averages of cells in the central Arctic range from 0.76 in April to 0.47 in August. The monthly averages of the within-cell standard deviations in the central Arctic are 0.04 in April and 0.06 in September. The surface albedo and surface temperature are correlated most strongly in March (R = -0.77) with little correlation in the summer. The monthly average lead fraction is determined from the mean potential open water, a scaled representation of the temperature or albedo between 0.0 (for ice) and 1.0 (for water); in the central Arctic it rises from an average 0.025 in the spring to 0.06 in September. Sparse data on aerosols, ozone, and water vapor in the atmospheric column contribute uncertainties to instantaneous, area-average albedos of 0.13, 0.04, and 0.08. Uncertainties in monthly average albedos are not this large. Contemporaneous estimation of these variables could reduce the uncertainty in the estimated albedo considerably. The poor calibration of AVHRR channels 1 and 2 is another large impediment to making accurate albedo estimates.
This report documents the preliminary design for a military fixed-base power system of 3 MWe nominal capacity using Westinghouse's tubular Solid Oxide Fuel Cell [SOFC] and Haldor Topsoe's logistic fuels processor [LFP]. The LFP provides to the fuel cell a methane rich sulfur free fuel stream derived from either DF-2 diesel fuel, or JP-8 turbine fuel. Fuel cells are electrochemical devices that directly convert the chemical energy contained in fuels such as hydrogen, natural gas, or coal gas into electricity at high efficiency with no intermediate heat engine or dynamo. The SOFC is distinguished from other fuel cell types by its solid state ceramic structure and its high operating temperature, nominally 1000'C. The SOFC pioneered by Westinghouse has a tubular geometry closed at one end. A power generation stack is formed by aggregating many cells in an ordered array. The Westinghouse stack design is distinguished from other fuel cell stacks by the complete absence of high integrity seals between cell elements, cells, and between stack and manifolds. Further, the reformer for natural gas [predominantly methane] and the stack are thermally and hydraulically integrated with no requirement for process water. The technical viability of combining the tubular SOFC and a logistic fuels processor was demonstrated at 27 kWe scale in a test program sponsored by the Advanced Research Projects Agency [ARPA) and carried out at the Southern California Edison's [SCE] Highgrove generating station near San Bernardino, California in 1994/95. The LFP was a breadboard design supplied by Haldor Topsoe, Inc. under subcontract to Westinghouse. The test program was completely successful. The LFP fueled the SOFC for 766 hours on JP-8 and 1555 hours of DF-2. In addition, the fuel cell operated for 3261 hours on pipeline natural gas. Over the 5582 hours of operation, the SOFC generated 118 MVVH of electricity with no perceptible degradation in performance. The LFP processed military specification JP-8 and DF-2 removing the sulfur and reforming these liquid fuels to a methane rich gaseous fuel. Results of this program are documented in a companion report titled 'Final Report-Solid Oxide Fuel Cell/ Logistic Fuels Processor 27 kWe Power System'.
Changes in the vacuolation in root apex cells of soybean (Glycine max L. [Merr.]) seedlings grown in microgravity were investigated. Spaceflight and ground control seedlings were grown in the absence or presence of KMnO4 (to remove ethylene) for 6 days. After landing, in order to study of cell ultrastructure and subcellular free calcium ion distribution, seedling root apices were fixed in 2.5% (w/v) glutaraldehyde in 0.1 M cacodylate buffer and 2% (w/v) glutaraldehyde, 2.5% (w/v) formaldehyde, 2% (w/v) potassium antimonate K[Sb(OH)6] in 0.1 M K2HPO4 buffer with an osmolarity (calculated theoretically) of 0.45 and 1.26 osmol. The concentrations of ethylene in all spaceflight canisters were significantly higher than in the ground control canisters. Seedling growth was reduced in the spaceflight-exposed plants. Additionally, the spaceflight-exposed plants exhibited progressive vacuolation in the root apex cells, particularly in the columella cells, to a greater degree than the ground controls. Plasmolysis was observed in columella cells of spaceflight roots fixed in solutions with relatively high osmolarity (1.26 osmol). The appearance of plasmolysis permitted the evaluation of the water status of cells. The water potential of the spaceflight cells was higher than the surrounding fixative solution. A decrease in osmotic potential and/or an increase in turgor potential may have induced increases in cell water potential. However, the plasmolysed (i.e. non-turgid) cells implied that increases in water potential were accompanied with a decrease in osmotic potential. In such cells changes in vacuolation may have been involved to maintain turgor pressure or may have been a result of intensification of other vacuolar functions like digestion and storage. c2003 COSPAR. Published by Elsevier Ltd. All rights reserved.
An autoclavable all-glass system for studying microbial dynamics at permeable surfaces is described. Standard hydrophobic or hydrophilic membranes (46-mm diameter) of various pore sizes were supported on a glass frit through which nutrient solutions were pumped by a peristaltic pump. The pump provided a precisely controlled flow at speeds of 0.5 to 500 ml of defined or natural cell exudates per h, which passed through the membrane into a receiving vessel. The construction allowed a choice of membranes, which could be modified. The system was tested with a bacterium, isolated from rape plant roots (Brassica napus L.), that was inoculated on a hydrophilic membrane filter and allowed to develop into a biofilm. A defined medium with a composition resembling that of natural rape root exudate was pumped through the membrane at 0.5 ml/h. Scanning electron microscopic examinations indicated that the inoculum formed microcolonies embedded in exopolymers evenly distributed over the membrane surface. The lipid composition and content of poly-beta-hydroxybutyrate in free-living and adhered cells were determined by gas chromatography. The bacterial consumption of amino acids in the exudate was also studied.
The 3.5 inch, 50 ampere-hour nickel-hydrogen cell was on a Low Earth Orbit (LEO) test regime and was being cycled at 10 C and 60 percent depth of discharge. At cycle number 511 the Automatic Control and Data Acquisition System (ACDAS) terminated the test when the end of discharge voltage dropped below the 1.00 volt cutoff. Upon removal of the stack assembly from the pressure vessel, portions of the zircar separator were found to be completely missing. Upon further examination portions of both the positive and negative plates were found to be missing from its substrate and several gas screens were damaged due to excessive heat which caused fusing. The postulated cause of failure is free electrolyte in the cell which caused oxygen channelization resulting in localized recombination which degraded the stack components.
Our laboratory has purified an 18 kDa cell surface sialoglycopeptide growth inhibitor (CeReS-18) from intact bovine cerebral cortex cells. Evidence presented here demonstrates that sensitivity to CeReS-18-induced growth inhibition in BALB-c 3T3 cells is influenced by calcium, such that a decrease in the calcium concentration in the growth medium results in an increase in sensitivity to CeReS-18. Calcium did not alter CeReS-18 binding to its cell surface receptor and CeReS-18 does not bind calcium directly. Addition of calcium, but not magnesium, to CeReS-18-inhibited 3T3 cells results in reentry into the cell cycle. A greater than 3-hour exposure to increased calcium is required for escape from CeReS-18-induced growth inhibition. The calcium ionophore ionomycin could partially mimic the effect of increasing extracellular calcium, but thapsigargin was ineffective in inducing escape from growth inhibition. Increasing extracellular calcium 10-fold resulted in an approximately 7-fold increase in total cell-associated 45Ca+2, while free intracellular calcium only increased approximately 30%. However, addition of CeReS-18 did not affect total cell-associated calcium or the increase in total cell-associated calcium observed with an increase in extracellular calcium. Serum addition induced mobilization of intracellular calcium and influx across the plasma membrane in 3T3 cells, and pretreatment of 3T3 cells with CeReS-18 appeared to inhibit these calcium mobilization events. These results suggest that a calcium-sensitive step exists in the recovery from CeReS-18-induced growth inhibition. CeReS-18 may inhibit cell proliferation through a novel mechanism involving altering the intracellular calcium mobilization/regulation necessary for cell cycle progression.
We introduce cracked film lithography (CFL) as a way to reduce the cost of III–V photovoltaics (PV). We spin-coat nanoparticle suspensions onto GaAs thin-film device stacks. The suspensions dry in seconds, forming crack networks that we use as templates through which to electroplate the solar cells’ front metal grids. For the first time, we show that heating the crack template allows it to flow and refill cracks, which decreases crack footprint and improves final grid transmittance. We demonstrate 24.7%-efficient single-junction GaAs solar cells using vacuum-free CFL grids. These devices are only 1.7% (absolute) less efficient than the baseline grids patterned by photolithography with the loss mostly resulting from the reduced transparency of the CFL pattern. Additional optimization could decrease this difference. Initial cost modeling suggests that CFL is more scalable than photolithography: In particular, CFL’s lower materials and equipment costs could greatly reduce the levelized cost of electricity of III–V PV at scale, a potential step toward terrestrial deployment.
In direct alcohol fuel cells (DAFCs), the oxidation of alcohols happens at the expenses of the oxygen reduction reaction at the cathode. DAFCs' cathodes use a significant amount of platinum that is an expensive critical raw material. Moreover, platinum oxidizes alcohols, a fact that combined with alcohol crossover, decreases significantly the performance of the cells. The use of Fe-based (Fe-N-C) platinum group metal–free (PGM-free) cathodes is a convenient strategy to overcome these limitations. This review analyzes the application of PGM-free cathodes to DAFCs. The discussion focuses on acidic systems and covers the following subjects: (i) the breakdown of DAFC potential in its components, (ii) the analysis of the advantages from the use of the PGM-free cathode, and (iii) a review of the performance and durability of DAFCs. Finally, the review closes with a view of the authors of the future perspective for the research.
Development of boron diffusion process to diffuse large quantities of stress-free, high efficiency, radiation resistant solar cells
Proton-exchange membrane fuel cells (PEMFCs) are efficient and clean hydrogen energy technologies for transportation and stationary applications. Highly active and durable low-cost cathode catalysts for the oxygen-reduction reaction (ORR) under challenging acidic environments are desperately needed to address the cost and durability issues of PEMFCs. The most promising platinum group metal (PGM)-free catalysts for the ORR in acidic media are atomically dispersed and nitrogen-coordinated metal site catalysts denoted as M–N–C, M = Fe, Co, or Mn. Due to significant efforts in the past few decades, these catalysts have demonstrated much-improved ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the insufficient long-term stability (up to 5000 h) under PEMFC operation represents a primary technical barrier to making current PGM-free catalysts less viable yet in PEMFCs. In this Account, we highlight recent advances in synthesizing efficient PGM-free catalysts for the ORR in PEMFCs, emphasizing effective strategies to improve mass and intrinsic activity and the possible degradation mechanisms. In particular, a chemical doping method based on the zeolitic imidazolate framework (ZIF)-8 represents the key to developing efficient M–N–C catalysts containing atomically dispersed and nitrogen-coordinated single metal active sites (i.e., MN 4 ). The newly acquired understanding of the formation mechanism of MN 4 active sites during the thermal activation and its correlation to catalytic properties guide the rational catalyst design rather than relying on current trial-and-error approaches. Considerable efforts have further been invested in increasing the active site density and enhancing intrinsic activity by regulating carbon-phase structures and the local coordination environment. Furthermore, these highly active catalysts usually suffer from significant activity loss during the ORR. Therefore, breaking the activity–stability trade-off is the key to simultaneously achieving activity and stability in one catalyst, which is discussed on the basis of our recent successes in regulating local carbon structures surrounding active single metal sites. Significant research efforts toward understanding the degradation mechanisms and improving the lifetime of PGM-free catalysts are still crucial for viable applications in the future. Novel electrode designing strategies are needed to translate the PGM-free catalysts’ ORR activity to solid-state electrolyte-based membrane electrode assemblies (MEAs) with robust three-phase (i.e., gas–liquid–solid) interfaces for efficient charge and mass transports for performance improvement. On the basis of our effort at the University at Buffalo supported by ElectroCat Consortium associated with U.S. DOE’s Hydrogen and Fuel Cell Technologies Office, we provide a perspective on PGM-free cathode catalysts concerning remaining bottlenecks and future opportunities, aiming to inspire the community in both mechanistic understanding and technological development.
Lithium-metal batteries with zero excess lithium on the anode side paired with a fully lithiated cathode are regarded as a form of the highest energy-density configuration. Unfortunately, the continuous lithium loss over cycling from a limited amount of lithium reservoir significantly degrades the overall cell performance in the anode-free system. To mitigate the deterioration, modifying the current collector for enhanced lithium cycling is an indispensable route. Here, we apply a Ag/Cu ion exchange to precipitate micro-sized Ag particles on the Cu current collector to enhance the lithium reversibility via (de)alloying process. Further, we show a smoother morphology of lithium upon alloying, which leads to a lowered nucleation potential as well as increased average Coulombic efficiency in Li||Cu cells regardless of electrolyte formulation. The preferred lithium adsorption on Ag and AgLi over Cu is demonstrated with density functional theory calculations, which supports that Li is forming a gamma-phase alloy in the last stage rather than being deposited beneath the alloy. Lastly, this simple Cu foil modification enhances lithium reversibility and reduces its nucleation barrier, thus mitigating the capacity fade of a Cu||LiFePO 4 with reduced polarization.
Nonfullerene organic photovoltaics (OPVs) have achieved a breakthrough in pushing the efficiency beyond 15%. Although this sheds light on OPV commercialization, the high cost associated with the scalable device fabrications remains a giant challenge. Herein, a vacuum-free, all-solution and all-air processed OPV is reported that yields 11.12% efficiency with a fill factor of 0.725, due to the usages of high-merit polymeric electrodes and modified active blends. The design principle toward the high-merit electrodes is to induce heavy acid doping into the matrices for a raised carrier concentration and mobility, make a large removal of insulating components in the whole matrices rather than surfaces, and restrain the formation of large-domain aggregates. A unique layer-by-layer doping is developed to enable the polymeric electrodes with record-high trade-offs between optical transmittance and electrical conductivity. Moreover, solvent vapor annealing is proposed to boost device efficiency and it has the advantages of finely adjusting the active blend morphology and raising the electron mobility. The resulting devices are highly efficient and most (≈91%) of the initial efficiency are maintained in 30 day storage. Finally, this work indicates bright future for making cost-effective all-solution processed OPVs in air.