Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Microstructure of Li(Mn{sub 1/3}Ni{sub 1/3}Co{sub 1/3})O{sub 2} cathode material for lithium ion battery: Dependence of crystal structure on calcination and heat-treatment temperature

Graphical abstract: TEM micrograph of Li(Mn{sub 1/3}Ni{sub 1/3}Co{sub 1/3})O{sub 2} compound calcined at 900 °C. - Highlights: • Synthesis condition of Li(Mn{sub 1/3}Ni{sub 1/3}Co{sub 1/3})O{sub 2} compound was optimized. • Effect of calcination and heat treatment on the structure was investigated. • Controlled heat-treatment reduced cation mixing and improved structural ordering. • Calcination and heat-treatment condition affected distribution of particle size. - Abstract: Cathode compounds of composition Li(Mn{sub 1/3}Ni{sub 1/3}Co{sub 1/3})O{sub 2} have been prepared by calcination of the precursor materials at 700, 800, 900 and 1000 °C for 24 h and by subsequent heat-treatments at 1100 °C for 4–6 h. It has been observed that the structural ordering and particle size increase with increasing calcination temperature. The compounds calcined at 700 °C and 800 °C are not well-crystallized, but the distribution of particles is uniform. However, the compounds calcined at 900 °C and 1000 °C are well-crystallized with a non-uniform distribution of particles. The compounds calcined at 900 °C are well-crystallized with a well-ordered hexagonal structure. The samples calcined at 800 °C and heat treated at 1100 °C for 4 h also show same structure. They have smooth surface morphology with uniform distribution of particles in the sub-micron (0.15–0.40 μm) range and less amount of cation mixing.

36 MATERIALS SCIENCE↗

Thermal runaway mechanism of lithium-ion battery with LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode materials

Battery safety is critical to the application of lithium-ion batteries, especially for high energy density battery applied in electric vehicles. In this paper, the thermal runaway mechanism of LiNi 0.8 Co 0.1 Mn 0.1 O 2 based lithium-ion battery is illustrated. And the reaction between cathode and flammable electrolyte is proved as the trigger of the thermal runaway accident. In detail, with differential scanning calorimeter tests for battery components, the material combination contributing to thermal runaway was decoupled. Characterization with synchrotron X-ray diffraction and transmission electron microscopy with in-situ heating proved that the vigorous exothermic reaction is initiated by the liberated oxygen species. The pulse of highly active oxygen species reacted quickly with the electrolyte, accompanied with tremendous heat release, which accelerated the phase transformation of charged cathode. Also, the mechanism is verified by a confirmatory experiment when the highly active oxygen species were trapped by anion receptor, the phase transformation of the charged cathode was inhibited. Clarifying the thermal runaway mechanism of LiNi 0.8 Co 0.1 Mn 0.1 based lithium-ion battery may light the way to battery chemistries of both high energy density and high safety.

25 ENERGY STORAGE↗

On the P2-Na x Co 1– y (Mn 2/3 Ni 1/3 ) y O 2 Cathode Materials for Sodium-Ion Batteries: Synthesis, Electrochemical Performance, and Redox Processes Occurring during the Electrochemical Cycling

P2-type NaMO 2 sodiated layered oxides with mixed transition metals are receiving considerable attention for use as cathodes in sodium-ion batteries. A study on solid solution (1 – y)P2-Na x CoO 2 –( y )P2-Na x Mn 2/3 Ni 1/3 O 2 ( y = 0, 1/3, 1/2, 2/3, 1) reveals that changing the composition of the transition metals affects the resulting structure and the stability of pure P2 phases at various temperatures of calcination. For 0 ≤ y ≤ 1.0, the P2-Na x Co (1– y ) Mn 2 y /3 Ni y /3 O 2 solid-solution compounds deliver good electrochemical performance when cycled between 2.0 and 4.2 V versus Na + /Na with improved capacity stability in long-term cycling, especially for electrode materials with lower Co content ( y = 1/2 and 2/3), despite lower discharge capacities being observed. The (1/2)P2-Na x CoO 2 –(1/2)P2-Na x Mn 2/3 Ni 1/3 O 2 composition delivers a discharge capacity of 101.04 mAh g –1 with a capacity loss of only 3% after 100 cycles and a Coulombic efficiency exceeding 99.2%. Cycling this material to a higher cutoff voltage of 4.5 V versus Na + /Na increases the specific discharge capacity to ≈140 mAh g –1 due to the appearance of a well-defined high-voltage plateau, but after only 20 cycles, capacity retention declines to 88% and Coulombic efficiency drops to around 97%. In situ X-ray absorption near-edge structure measurements conducted on composition Na x Co 1/2 Mn 1/3 Ni 1/6 O 2 ( y = 1/2) in the two potential windows studied help elucidate the operating potential of each transition metal redox couple. As a result, it also reveals that at the high-voltage plateau, all of the transition metals are stable, raising the suspicion of possible contribution of oxygen ions in the high-voltage plateau.

25 ENERGY STORAGE↗

Study of the Durability of Doped Lanthanum Manganite and Cobaltite Cathode Materials under ''Real World'' Air Exposure Atmospheres

The overall objective of the program is to develop and validate mechanisms responsible for the overall structural and chemical degradation of lanthanum manganite as well as lanthanum ferrite cobaltite based cathode when exposed to “real world” air atmosphere exposure conditions during SOFC systems operation. Of particular interest are the evaluation and analysis of degradation phenomena related to and responsible for (a) products formation and interactions with air contaminants, (b) dopant segregation and oxide exolution at free surfaces, (c) cation interdiffusion and reaction products formation at the buried interfaces, (d) interface morphology changes, lattice transformation and the development of interfacial porosity and (e) micro-cracking and delamination from the stack repeat units. Reaction processes have been studied using electrochemical and high temperature materials compatibility tests followed by structural and chemical characterization. Degradation hypothesis has been proposed and validated through further experimentation and computational simulation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Novel Silver Molybdenum Oxyfluoride Perovskite as a Cathode Material for Lithium Batteries

Novel electroactive nanostructured silver molybdenum oxyfluoride (SMOF) perovskites Ag{sup 1+}{sub 3}Mo{sup 6+}(O{sub 3}F{sub 3}) have been successfully synthesized by a mechanochemical reaction. The formation of this perovskite was investigated throughout the Ag-Mo composition range with the use of either Ag{sup 1+} or Ag{sup 2+} in the form of AgF and AgF{sub 2} as the reactant, respectively. The compositional study combined with X-ray diffraction and extensive Raman investigation was utilized to determine structure and cation distribution and infer oxidation state. Finally, preliminary electrochemical characterization of the perovskites vs lithium was investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lithicone‐Protected Lithium Metal Anodes for Lithium Metal Batteries with Nickel‐Rich Cathode Materials

The high energy density advantage of lithium (Li) metal batteries (LMBs) makes them increasingly desirable; however, problems such as strong reactivity and dendrite growth of Li metal anode limit their practical uses. In this work, a novel Li‐containing glycerol (LiGL) or lithicone protection layer on a 50 μm thick Li metal anode is employed for improving the performance of LMBs. This LiGL layer was accurately deposited via a molecular layer deposition (MLD) process at 150 °C, using lithium tert‐butoxide and glycerol as precursors. The as‐formed LiGL coating layer is highly tunable in its thickness by simply adjusting MLD cycles and shows a good stability and outstanding ionic transport properties. The LiGL layer is found to effectively mitigate side reactions and enhance cycling stability in both symmetric cells and full cells. Specifically, the LMBs with LiGL@Li anode of 400 MLD cycles and LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode enable a capacity retention of ≈87%, much higher than ≈35% of the cells with bare Li after 200 cycles at a charge/discharge current density of 2.1 mA cm −2 . This work paves a feasible way for practical LMBs with improved capacity and stability through applying an innovative protection layer on Li metal anodes.

25 ENERGY STORAGE↗

High Energy Density Li-ion Cells for EV’s Based on Novel, High Voltage Cathode Material Systems

This Li-ion cell technology development project had three objectives: to develop advanced electrode materials and cell components to enable stable high-voltage operation; to design and demonstrate a Li-ion cell using these materials that meets the PHEV40 performance targets; and to design and demonstrate a Li-ion cell using these materials that meets the EV performance targets. The major challenge to creating stable high energy cells with long cycle life is system integration. Although materials that can give high energy cells are known, stabilizing them towards long-term cycling in the presence of other novel cell components is a major challenge. The major technical barriers addressed by this work include low cathode specific energy, poor electrolyte stability during high voltage operation, and insufficient capacity retention during deep discharge for Si-containing anodes. Through the course of this project, Farasis was able to improve capacity retention of NCM materials for 4.4+ V operation, through both surface treatment and bulk-doping approaches. Other material advances include increased rate capability and of HE-NCM materials through novel synthesis approach, doubling the relative capacity at 1C over materials synthesized using standard methods. Silicon active materials proved challenging throughout the project and ultimately were the limiting factor in the energy density vs. cycle life trade off. By avoiding silicon anodes for the lower energy PHEV design, we manufactured cells with intermediate energy density and long cycle life under high voltage operation for PHEV applications. Cells with high energy density for EV applications were manufactured targeting a 300 Wh/kg design and were able to achieve > 200 cycles.

25 ENERGY STORAGE↗

First-Cycle Simulation for Li-Rich Layered Oxide Cathode Material x Li 2 MnO 3 • (1- x )Li M O 2 ( x = 0.4)

Here, lithium-rich layered oxides (LRLO) x Li 2 MnO 3 • (1- x )Li M O 2 continue to attract attention owing to their promise of high capacity and energy density as lithium-ion battery cathodes, despite the degradation of atomic structure and energy density (voltage fade) with cycling. First-principles DFT calculations for the model systems M = Co and M = Mn 0.5 Ni 0.5 provide insights into the atomic-scale transformations in the bulk during the first charge and discharge of LRLO. The simulations were performed with the VASP code at the GGA+ U level. Molecular dynamics simulations were conducted at T = 1000 K (charge) and 2000 K (discharge) to accelerate the dynamics. Considerable Co migration to the Li layer occurs during the first charge for the system with M = Co, but the Li M O 2 component remains substantially intact for the system with M = Mn 0.5 Ni 0.5 . First-charge oxygen dimerization in the M = Co system occurs in both the Li M O 2 and the Li 2 MnO 3 components of the material, and exceeds than for M = Mn 0.5 Ni 0.5 , where dimerization is essentially confined to the Li 2 MnO 3 component. About half of the oxygen dimers created during the voltage plateau dissociate during the first discharge. Analysis of the redox suggests that some Mn 3+ is generated during the first charge for the system M = Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DFT simulation of the X-ray diffraction pattern of aluminum-ion-intercalated graphite used as the cathode material of the aluminum-ion battery

Many breakthroughs have been achieved in rechargeable aluminum-ion battery technologies in recent years. Most recently, operando X-ray diffraction (XRD) combined with density functional theory (DFT) calculations was reported to study the chloroaluminate anion (AlCl 4 -)-intercalated graphite cathode of the battery. However, there are quite a few discrepancies between the measured and simulated XRD patterns. This work is focused on the simulation of XRD patterns of graphite intercalation compounds (GICs) with DFT calculations. Our results reveal that both the geometry of AlCl 4 - in graphite and the gallery height of GICs are dependent on the intercalant density. At low intercalant density, the gallery height keeps constant, but at high intercalant densities, the gallery height is linearly related to the intercalant density. Our simulated XRD patterns are highly consistent with the measured operando XRD patterns. Not only do the angles of the peaks match very well, but also the relative intensities and the corresponding electrode capacities show reasonable agreement with the experimental results. The DFT simulation of the XRD pattern provides significant information on the stage index and the charge capacity of the GIC electrode.

25 ENERGY STORAGE↗

Phase Control on Surface for the Stabilization of High Energy Cathode Materials of Lithium Ion Batteries

The development of high energy electrode materials for lithium ion batteries is challenged by their inherent instabilities, which become more aggravated as the energy densities continue to climb, accordingly causing increasing concerns on battery safety and reliability. Here, taking the high voltage cathode of LiNi 0.5 Mn 1.5 O 4 as an example, we demonstrate a protocol to stabilize this cathode through a systematic phase modulating on its particle surface. We are able to transfer the spinel surface into a 30 nm shell composed of two functional phases including a rock-salt one and a layered one. The former is electrochemically inert for surface stabilization while the latter is designated to provide necessary electrochemical activity. The precise synthesis control enables us to tune the ratio of these two phases, and achieve an optimized balance between improved stability against structural degradation without sacrificing its capacity. This study highlights the critical importance of well-tailored surface phase property for the cathode stabilization of high energy lithium ion batteries.

25 ENERGY STORAGE↗

Aerospace applications of sodium batteries using novel cathode materials

Preliminary fundamental investigations aimed at evaluating sodium metal chloride systems for future aerospace applications are described. Since the sodium metal chloride systems are relatively new, the approach has been to characterize their fundamental properties in order to understand their limitations. To this end, a series of fundamental electrochemical investigations have been carried out, the results of which are reported here. The metal chloride cathodes show high exchange current densities which corroborate their good reversibility in a battery application. The reduction mechanisms appear to be complex and involve multielectron transfer steps and intermediates. Such intermediates in the reaction mechanism have already been identified in the case of FeCl2. Similar mechanisms may be operative in the case of NiCl2. CuCl2, however, exhibits a second relaxation loop in the impedance plot at low frequencies and also a sloping discharge curve, unlike FeCl2 and NiCl2, which may indicate the existence of monovalent copper in the reduction mechanism.

Ratnakumar, B. V.↗

Nitrogen-sulfur-carbon nanocomposites and their application as cathode materials in lithium-sulfur batteries

The invention is directed in a first aspect to electron-conducting porous compositions comprising an organic polymer matrix doped with nitrogen atoms and having elemental sulfur dispersed therein, particularly such compositions having an ordered framework structure. The invention is also directed to composites of such S/N-doped electron-conducting porous aromatic framework (PAF) compositions, or composites of an S/N-doped mesoporous carbon composition, which includes the S/N-doped composition in admixture with a binder, and optionally, conductive carbon. The invention is further directed to cathodes for a lithium-sulfur battery in which such composites are incorporated.

25 ENERGY STORAGE↗