SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Complementary Aerodynamic Performance Datasets for Variable Speed Power Turbine Blade Section from Two Independent Transonic Turbine Cascades

Two independent experimental studies were conducted in linear cascades on a scaled, two-dimensional mid-span section of a representative Variable Speed Power Turbine (VSPT) blade. The purpose of these studies was to assess the aerodynamic performance of the VSPT blade over large Reynolds number and incidence angle ranges. The influence of inlet turbulence intensity was also investigated. The tests were carried out in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility and at the University of North Dakota (UND) High Speed Compressible Flow Wind Tunnel Facility. A large database was developed by acquiring total pressure and exit angle surveys and blade loading data for ten incidence angles ranging from +15.8deg to −51.0deg. Data were acquired over six flow conditions with exit isentropic Reynolds number ranging from 0.05×106 to 2.12×106 and at exit Mach numbers of 0.72 (design) and 0.35. Flow conditions were examined within the respective facility constraints. The survey data were integrated to determine average exit total-pressure and flow angle. UND also acquired blade surface heat transfer data at two flow conditions across the entire incidence angle range aimed at quantifying transitional flow behavior on the blade. Comparisons of the aerodynamic datasets were made for three "match point" conditions. The blade loading data at the match point conditions show good agreement between the facilities. This report shows comparisons of other data and highlights the unique contributions of the two facilities. The datasets are being used to advance understanding of the aerodynamic challenges associated with maintaining efficient power turbine operation over a wide shaft-speed range.

Turbine↗

NASA NTRS2015

Comparison of Computational and Experimental Results for a Transonic Variable-speed Power-Turbine Blade Operating with Low Inlet Turbulence Levels

A computational assessment of the aerodynamic performance of the midspan section of a variable-speed power-turbine blade is described. The computation comprises a periodic single blade that represents the 2-D Midspan section VSPT blade that was tested in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. A commercial, off-the-shelf (COTS) software package, Pointwise and CFD++, was used for the grid generation and RANS and URANS computations. The CFD code, which offers flexibility in terms of turbulence and transition modeling options, was assessed in terms of blade loading, loss, and turning against test data from the transonic tunnel. Simulations were assessed at positive and negative incidence angles that represent the turbine cruise and take-off design conditions. The results indicate that the secondary flow induced at the positive incidence cruise condition results in a highly loaded case and transitional flow on the blade is observed. The negative incidence take-off condition is unloaded and the flow is very two-dimensional. The computational results demonstrate the predictive capability of the gridding technique and COTS software for a linear transonic turbine blade cascade with large incidence angle variation.

rotary wing↗

NASA NTRSDate not supplied

Predicted Performance Effects of Blade Elasticity on Testing of Rotors for Mars

The Rotor Optimization for the Advancement of Mars Exploration project (ROAMX) has designed and manufactured a set of rotor blades optimized for hover on Mars. These blades will soon be tested for hover performance in the NASA Ames Research Center Planetary Aeolian Laboratory, a large vacuum chamber capable of rotor testing at reduced pressures. To match the tip Mach numbers during this testing with the tip Mach numbers that would be experienced in the Martian atmosphere, the rotor will be spun faster in the vacuum chamber than it would be spun on Mars. While this accomplishes the goal of simulating the tip Mach numbers of Mars operations, the elevated RPM may have undesired consequences for performance, due to elastic deflections of the blades. The purpose of this paper is to use CAMRAD II, a rotorcraft comprehensive analysis code, to predict the effect on performance of blade elasticity at elevated RPM in the vacuum chamber environment. Results are presented for different thrust conditions and different rotor speeds, and comparisons are made between rigid and elastic blade predictions. Overall, the CAMRAD II analysis suggests that blade elasticity does influence rotor performance in the operating conditions of interest, although the effect is moderate enough to conclude that the PAL testing will be a good simulation of Mars operation.

Blade elasticity↗

DOE OSTI2022

Wind turbine blade design with airfoil shape control using invertible neural networks

Wind turbine blade design is a highly multidisciplinary process that involves aerodynamics, structures, controls, manufacturing, costs, and other considerations. More efficient blade designs can be found by controlling the airfoil cross-sectional shapes simultaneously with the bulk blade twist and chord distributions. Prior work has focused on incorporating panel-based aerodynamic solvers with a blade design framework to allow for airfoil shape control within the design loop in a tractable manner. Including higher fidelity aerodynamic solvers, such as computational fluid dynamics, makes the design problem computationally intractable. In this work, we couple an invertible neural network trained on high-fidelity airfoil aerodynamic data to a turbine design framework to enable the design of airfoil cross sections within a larger blade design problem. We detail the methodology of this coupled framework and showcase its efficacy by aerostructurally redesigning the IEA 15-MW reference wind turbine blade. The coupled approach reduces the cost of energy by 0.9% compared to a more conventional design approach. This work enables the inclusion of high-fidelity aerodynamic data earlier in the design process, reducing cycle time and increasing certainty in the performance of the optimal design.

17 WIND ENERGY↗

NASA NTRS2014

Structural Health Monitoring on Turbine Engines Using Microwave Blade Tip Clearance Sensors

The ability to monitor the structural health of the rotating components, especially in the hot sections of turbine engines, is of major interest to aero community in improving engine safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, are able to operate in a high temperature environment, and can detect minute changes and hidden flaws before catastrophic events occur. The National Aeronautics and Space Administration (NASA) has taken a lead role in the investigation of new sensor technologies and techniques for the in situ structural health monitoring of gas turbine engines. As part of this effort, microwave sensor technology has been investigated as a means of making high temperature non-contact blade tip clearance, blade tip timing, and blade vibration measurements for use in gas turbine engines. This paper presents a summary of key results and findings obtained from the evaluation of two different types of microwave sensors that have been investigated for use possible in structural health monitoring applications. The first is a microwave blade tip clearance sensor that has been evaluated on a large scale Axial Vane Fan, a subscale Turbofan, and more recently on sub-scale turbine engine like disks. The second is a novel microwave based blade vibration sensor that was also used in parallel with the microwave blade tip clearance sensors on the experiments with the sub-scale turbine engine disks.

Gas Turbine Engines↗

NASA NTRS2020

Investigation of a Helicopter Individual Blade Control (IBC) System in Two Full-Scale Wind Tunnel Tests: Volume I

This report presents the data acquired during the testing of an individual blade control (IBC) system on a full-scale helicopter rotor in two test entries in the NASA Ames 40- by 80-Foot Wind Tunnel. The objective of these investigations was to evaluate the potential benefits of using IBC to improve rotor performance, reduce blade vortex interaction (BVI) noise, and alleviate helicopter vibrations. The wind tunnel tests were an international, collaborative effort between NASA, the U.S. Army Aeroflightdynamics Directorate, ZF Luftfahrttechnik GmbH, Eurocopter Deutschland GmbH, and the German Aerospace Laboratory (DLR). They were conducted as a task of the U.S./German Memorandum of Understanding (MOU) on Helicopter Aeromechanics. The IBC tests were performed using a full-scale BO-105 helicopter rotor mounted to the NASA/U.S. Army Rotor Test Apparatus (RTA). The first test, performed in 1993, was the first full-scale wind tunnel test to explore the effects of an IBC system on rotor vibration, noise, and performance. In this test, the pitch links of the rotor were replaced by servo-actuators. The servo-actuators and IBC control system were designed and manufactured by ZF Luftfahrttechnik GmbH. This control system allowed the pitch of each rotor blade to be changed independently of the other blades. The IBC inputs had large effects on the hub vibrations and BVI noise. However, the rotor hub moments were not retrimmed with each new IBC input. This resulted in an out-of-trim rotor configuration. The same IBC system was used in the second IBC test performed in 1994. This test more carefully investigated the potential of IBC to simultaneously reduce noise and vibration and also investigated the effect of IBC on rotor performance in high-speed-cruise flight. In the 1994 test, the hub moment and rotor thrust were readjusted to maintain rotor trim as the IBC inputs were applied. For this reason, the data taken from the second test are considered to be more accurate, except for some unique IBC input combinations not repeated in the second test. IBC controls that were evaluated were single-frequency inputs from 2/rev to 6/rev and multi-harmonic combinations of these frequencies to form pulses, wavelets, and doublets. Extensive data were acquired for each IBC data point. These data included rotor performance, average and time-varying hub loads, rotor blade bending loads, control system loads, inboard and outboard blade pitch motions, and BVI noise data. The rotor balance hub force and moment data included the mean values, half-peak-to-peak values, and sine/cosine harmonics up to the 20th rotor harmonic. The time history and averaged Fourier spectrum for each measurement are available electronically from NASA Ames Research Center. The data indicate that significant reduction in both BVI noise and hub vibration can be obtained using IBC. The 2/rev input produced the best single-frequency results. At a typical descent flight condition, 2/rev IBC combined with other IBC harmonics reduced the BVI noise up to 12 dB (85 percent) at some microphone locations. At the same time, this input could also reduce the dominant 4/rev vibratory hub loads by up to 75 percent. The data also show that performance improvements of up to 7 percent were obtained using 2/rev IBC at high-speed forward flight conditions. An analysis of the hydraulic power requirements for BVI noise suppression, vibration reduction, and rotor performance improvement is included in this report. This analysis shows that the power required by the IBC system is negligible at low-speed flight conditions, and that a net gain of 3 percent of rotor horsepower can be achieved at high-speed flight conditions.

Investigation↗

DOE OSTI2020

Impact of control blade insertion on the deformation behavior of SiC-SiC channel boxes in BWRs

This article describes the analysis of distortion of a silicon carbide fiber-reinforced, silicon carbide matrix (SiC-SiC) composite channel box under in-reactor conditions of a boiling water reactor (BWR). The BWR core has significant gradients in the fast neutron flux across the channel box due to the presence of water rods within the fuel assemblies, and these gradients increase further with the insertion of control blades. As a result of the temperature and neutron flux dependent irradiation-induced swelling of SiC, the SiC-SiC composite channel box can undergo distortion. In this work, we evaluate the SiC-SiC channel box distortion for three different control blade positions. This analysis is based on the neutron flux and temperature distributions in the BWR core calculated using the neutronics code MPACT and thermal-hydraulics code CTF. This calculation is coupled through temperature feedback. Subsequently, we have performed structural analysis based on the calculated neutron flux and temperature distributions to determine the deformation and stress development in the channel box. The structural analysis was performed using the fuel performance modeling code BISON and the commercial finite element analysis software Abaqus. The results indicate that large gradients in fast neutron flux (up to 35–40% across a single axial level) will develop across the channel box. Due to these gradients, the channel box will undergo time-dependent bending for all the control blade positions in the assembly. The time-dependent bowing behavior is dominated by the transient swelling of SiC-SiC material under non-uniform neutron flux, and changes with variation in the control blade position. The bending will cause temporary interference between the channel box and control blade, and the interference is expected to be most severe for the fully inserted control blade position. The developed stresses due to differential swelling in the channel box exceed the proportional limit stress of the material, which may cause matrix microcracking in the channel box. However, the stresses remain below the tensile strength of the material, and therefore, development of a full, through-thickness crack in the channel box is not expected. Finally, further work is recommended to explore and evaluate the mitigation strategies.

42 ENGINEERING↗

NASA NTRS1972

A Theoretical and Experimental Investigation of Flap-Lag Stability of Hingeless Helicopter Rotor Blades

The stability of hingeless rotor blade oscillations in hover is examined theoretically using a simplified centrally-hinged, spring-restrained, rigid blade to approximate the deflections of actual elastic blades. The aerodynamic and inertial coupling between the flap and lead-lag degrees of freedom is primarily responsible for instability, however elastic coupling and kinematic pitch-lag coupling both exert a powerful influence on hingeless rotor blade stability. Experimental results obtained from a two-bladed 1.81m diameter model rotor designed for minimum elastic coupling have confirmed the results of linear theory. For this model configuration rotor blade stall at high pitch angles was found to counteract the destabilizing flap-lag coupling and increase the damping of lead-lag oscillations. It was possible to account for this effect with the theory by using drag data for stalled airfoils.

Ormiston, R. A.↗

NASA NTRS1972

Turbulent boundary layer on a rotating helical blade.

Investigation of the boundary-layer characteristics on a helical blade of large chord length, enclosed in an annulus and rotating in a fluid otherwise at rest. The three-dimensional form of momentum integral equations is derived, and is used to predict the boundary-layer growth and limiting streamline angles on the blade surface. The measurements are in general agreement with the predictions. The wall shear stress correlation, which includes both Reynolds number and rotation parameters, valid for a rotating blade operating at zero pressure gradient, is derived. Radial and tangential velocity profiles, the tangential component of turbulence intensity, and blade static pressures are measured at several locations on the blade surface. The nature of flow near the blade tip is discussed. An expression for the radial velocity profile, valid in the outer region of the boundary layer, is derived theoretically.

Lakshminarayana, B.↗

NASA NTRS1972

Methods for reducing blade passing frequency noise generated by rotor-wake - stator interaction

A theoretical model for the generation of blade-passage noise caused by the interaction of rotor wakes with the downstream stator blades in a fan stage has been compiled. This model has combined a description of the rotor wake based on existing experimental correlations with an existing theory for the response of the stator blades to those wakes. This model of the interaction-caused blade-passage noise has been used to examine some effects of blade geometry and flow conditions on the noise generated. A set of significant parameters has been identified to reduce this interaction-caused blade-passage frequency noise. A redesign of an existing fan with the use of these concepts has produced a theoretical noise reduction of more than 7 decibels.

Dittmar, J. H.↗

NASA NTRS1972

Effects of increased leading-edge thickness on performance of a transonic rotor blade

A single-stage transonic compressor was tested with two rotor blade leading-edge configurations to investigate the effect of increased leading-edge thickness on the performance of a transonic blade row. The original rotor blade configuration was modified by cutting back the leading edge sufficiently to double the blade leading-edge thickness and thus the blade gap blockage in the tip region. At design speed this modification resulted in a decrease in rotor overall peak efficiency of four points. The major portion of this decrement in rotor overall peak efficienty was attributed to the flow conditions in the outer 30 percent of the blade span. At 70 and 90 percent of design speed, the modification had very little effect on rotor overall performance.

Reid, L.↗

NASA NTRS1974

FOD impact testing of composite fan blades

The results of impact tests on large, fiber composite fan blades for aircraft turbofan engine applications are discussed. Solid composite blades of two different sizes and designs were tested. Both graphite/epoxy and boron/epoxy were evaluated. In addition, a spar-shell blade design was tested that had a boron/epoxy shell bonded to a titanium spar. All blades were tested one at a time in a rotating arm rig to simulate engine operating conditions. Impacting media included small gravel, two inch diameter ice balls, gelatin and RTV foam-simulated birds, as well as starlings and pigeons. The results showed little difference in performance between the graphite and boron/epoxy blades. The results also indicate that composite blades may be able to tolerate ice ball and small bird impacts but need improvement to tolerate birds in the small duck and larger category.

Johns, R. H.↗

NASA NTRS1974

FOD impact testing of composite fan blades

The results of impact tests on large, fiber composite fan blades for aircraft turbofan engine applications are discussed. Solid composite blades of two different sizes and designs were tested. Both graphite/epoxy and boron/epoxy were evaluated. In addition, a spar-shell blade design was tested that had a boron/epoxy shell bonded to a titanium spar. All blades were tested one at a time in a rotating arm rig to simulate engine operating conditions. Impacting media included small gravel, two inch diameter ice balls, gelatin, and RTV foam-simulated birds, as well as starlings and pigeons. The results showed little difference in performance between the graphite and boron/epoxy blades. The results also indicate that composite blades may be able to tolerate ice ball and small bird impacts but need improvement to tolerate birds in the small duck and larger category.

Johns, R. H.↗

NASA NTRS1974

Impact testing on composite fan blades

Johns, R. H.↗

NASA NTRS1975

An approximate closed-form solution for lead lag damping of rotor blades in hover

Simple stability methods are used to derive an approximate, closed-form expression for the lead-lag damping of rotor blades in hover. Destabilizing terms are shown to be a result of two dynamic mechanisms. First, the destabilizing aerodynamic forces that can occur when blade lift is higher than a critical value are maximized when the blade motion is in a straight line equidistant from the blade chord and the average direction of the air flow velocity. This condition occurs when the Coriolis terms vanish and when the elastic coupling terms align the blade motion with this least stable direction. Second, the nonconservative stiffness terms that result from pitch-flap or pitch-lag coupling can add or subtract energy from the system depending upon whether the motion of the blade tip is clockwise or counterclockwise.

Peters, D. A.↗

NASA NTRS1975

A simulation study of active feedback supression of dynamic response in helicopter rotor blades

A parameter study is presented for active feedback control applied to a helicopter rotor blade during forward flight. The study was performed on an electromechanical apparatus which included a mechanical model rotor blade and electronic analog simulation of interaction between blade deflections and aerodynamic loading. Blade response parameters were obtained for simulated vortex impinging at the blade tip at one pulse per revolution, and for a pulse which traveled from the blade tip toward its root. Results show that the response in a 1 - 10-per-rev frequency band is diminished by the feedback action, but at the same time responses at frequencies above 10-per-rev become increasingly more prominent with increased feedback amplitude, and can even lead to instability at certain levels. It appears that the latter behavior results from limitations of the laboratory simulation apparatus, rather than genuine potential behavior for a prototype helicopter.

Kana, D. D.↗

NASA NTRS1975

100-kW hingeless metal wind turbine blade design, analysis and fabrication

The design, fabrication and analysis of aluminum wind turbine rotor blades is discussed. The blades are designed to meet criteria established for a 100-kilowatt wind turbine generator operating between 8 and 60-mile-per-hour speeds at 40 revolutions per minute. The design wind speed is 18 miles per hour. Two rotor blades are used on a new facility which includes a hingeless hub and its shaft, gearbox, generator and tower. Experience shows that, for stopped rotors, safe wind speeds are strongly dependent on blade torsional and bending rigidities which the basic D spar structural blade design provides. The 0.25-inch-thick nose skin is brake/bump formed to provide the basic 'D' spar structure for the tapered, twisted blades. Adequate margins for flutter and divergence are predicted from the use of existing, correlated stopped rotor and helicopter rotor analysis programs.

Donham, R. E.↗

NASA NTRS1976

Two-dimensional cold-air cascade study of a film-cooled turbine stator blade. 3: Effect of hole size on single-row and multirow ejection

The effect of coolant discharge on the aerodynamic performance of a film cooled turbine stator blade was determined. The blade had the same number, location, and injection angle of coolant holes, but the coolant hole diameters were one half that of a previously investigated blade. Otherwise the blades were the same. Tests with discharge from individual coolant rows and multiple coolant rows, including full film discharge are studied. The results of the blade with smaller holes are reported and compared with the blades with larger holes.

Prust, H. W., Jr.↗