Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “battery control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Preventing Voltage Divergence in Series-Stacked Bidirectional Battery Energy Storage DC-DC Converter under Asymmetrical Operating Conditions

DC stacked topologies have gained popularity for interfacing individual photovoltaic panels to a high-voltage DC bus. A similar approach can be used to interface individual battery packs to the same DC bus, which allows active balancing of battery substrings and the use of lower voltage switches. Any imbalance in battery current, however, can cause the converter output voltages to diverge. This paper describes the source of voltage divergence and demonstrates a solution that allows seamless stacking of multiple battery packs to be interfaced to a high voltage DC bus. To prevent the voltage divergence phenomenon and allow asymmetrical battery charging for efficient battery state of charge management, the PI-based decentralized voltage control enabling both capacitor voltage sharing and asymmetrical capacitor voltage control is proposed. The effectiveness of the decentralized voltage control strategy is demonstrated through controller hardware-in-the-loop test results.

Kim, Namwon↗
DOE OSTI2022

Tension‐Induced Cavitation in Li‐Metal Stripping

Abstract Designing stable Li metal and supporting solid structures (SSS) is of fundamental importance in rechargeable Li‐metal batteries. Yet, the stripping kinetics of Li metal and its mechanical effect on the supporting solids (including solid electrolyte interface) remain mysterious to date. Here, through nanoscale in situ observations of a solid‐state Li‐metal battery in an electron microscope, two distinct cavitation‐mediated Li stripping modes controlled by the ratio of the SSS thickness ( t ) to the Li deposit's radius ( r ) are discovered. A quantitative criterion is established to understand the damage tolerance of SSS on the Li‐metal stripping pathways. For mechanically unstable SSS ( t / r < 0.21), the stripping proceeds via tension‐induced multisite cavitation accompanied by severe SSS buckling and necking, ultimately leading to Li “trapping” or “dead Li” formation; for mechanically stable SSS ( t / r > 0.21), the Li metal undergoes nearly planar stripping from the root via single cavitation, showing negligible buckling. This work proves the existence of an electronically conductive precursor film coated on the interior of solid electrolytes that however can be mechanically damaged, and it is of potential importance to the design of delicate Li‐metal supporting structures to high‐performance solid‐state Li‐metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Modeling Framework for Data Center

This chapter highlights the critical need for advanced modeling of data centers due to their rapidly increasing energy consumption and impact on grid reliability. Driven by the demand for AI applications, data centers are projected to consume a significant portion of US energy by 2028, putting stress on an already challenged power grid. The chapter emphasizes the importance of "fast" time-scale models to understand the dynamic interactions between data centers and the grid, especially given the rapid power fluctuations of AI workloads. It outlines a modeling framework that includes both offline and real-time EMT domain simulations, detailing the necessary representations for various components like utility interfaces, transformers, IT loads, UPS, cooling loads, Battery Energy Storage Systems (BESS), generators, protection systems, and higher-level control systems. While standard simulation tools like PSCAD offer basic models, custom development is often required to accurately capture the unique and fast-changing behaviors of modern data centers. The chapter also discusses key metrics and test cases for validating these models, focusing on transient load responses, protection relay coordination, and demand flexibility. Finally, it addresses the challenges of modeling large-scale data centers, such as computational complexity and the trade-off between model fidelity and practicality, suggesting hybrid modeling approaches as a solution. The overarching goal is to create a robust framework that helps assess data center impacts on grid stability, identify vulnerabilities, and inform the development of standards for reliable integration of these large loads into the bulk power system.

25 ENERGY STORAGE↗
DOE OSTI2024

Risk-informed Hierarchical Control of Behind-the-Meter DERs with AMI Data Integration (Final Technical Report)

This project addresses several key barriers to implement the next generation demand response applications and provides a clear understanding of implementing hierarchical and standalone control using AMI data. Through this program, Eaton has developed and tested a meter-as-a-controller prototype with the help of other partners--- National Renewable Energy Laboratory (NREL), Electric Power Research Institute (EPRI), Pecan St Inc. (PSI), and Delaware Electric Cooperative (DEC). The controller can utilize residential controllable loads such as heating, ventilation, and air conditioner (HVAC), electric water heater and distributed energy resources like solar PV and battery energy storage systems for off-setting the demand that is required from the grid, thus providing reliable grid-services for demand reduction or peak shaving. The controller is also capable of coordinating the resources of the premises for better management and energy efficiency while meeting the comfort bound of the premises owner as quality-of-service. The development has been demonstrated in a three virtual-home setup at system performance lab of NREL with real appliances (HVAC, electric water heater, solar PV, and battery). The technology has also been proved through laboratory and field demonstration with successful interconnectivity (e.g., end-to-end communication and data exchange) between the residential appliances and utility through the RF network at Delaware Electric Co-op (DEC) in Delaware.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

On the quality of tape-cast thin films of sulfide electrolytes for solid-state batteries

All-solid-state lithium batteries (ASSLBs) have the potential to increase energy density, improve safety, and allow for lower manufacturing costs compared to conventional, liquid-based Li-ion batteries. The thickness of solid electrolyte (SE) layer dictates the cell-level energy density and it is desirable to make the SE layer as thin as possible while maintaining uniformity and defect-free. Manufacturing a high- quality, thin sulfide SE layer at large-scale, however, is challenging. Previous studies have addressed the compatibility of materials used for manufacturing thin sulfide SE films, paving the way for further investigation of processing conditions and film quality. Here we report a strong correlation between the solid loading of dispersions and the quality of tape-casted thin sulfide SE films. We also demonstrate a method for quantifying the quality of thin SE films by observing both pin-hole defects and larger heterogeneous agglomerations of particles in the films. Our thin sulfide SE films containing ~5 wt% binder are defect-free and show similar ionic conductivity compared to a cold-pressed, binder-free, thick SE pellet, resulting in an ~11X reduction of area specific resistance. Here, this work on the solid loading of the dispersion used in a scalable tape casting process provides insight for manufacturing high-quality, thin sulfide SE films and to increase the cell-level energy density of ASSLB.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Gel composite electrolyte – an effective way to utilize ceramic fillers in lithium batteries

Achieving synergy between ion-conducting polymers and ceramics in a composite electrolyte has been proven to be difficult as the complicated ceramic/polymer interface presents challenges to understand and control. In this work, we report a strategy to utilize discrete ceramic fillers to form a gel composite electrolyte with enhanced transport properties for lithium metal batteries. The matrix of the composite membrane is crosslinked poly(ethylene oxide) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). The membrane is plasticized with tetraethylene glycol dimethyl ether (TEGDME). The incorporation of doped-lithium aluminum titanium phosphate particles (LICGC™) into the membrane greatly improves the membrane's cycling characteristics against the lithium electrode, exhibiting lower interfacial impedance, lower overpotential and higher rate capability. The underpinnings of the superior performance of the gel composite electrolyte are discussed in depth. LICGC™ can immobilize the TFSI - anions in the polymer matrix and simultaneously promote Li+ transport by increasing the plasticizer to Li + ratio. Further, the transport enhancement is achieved without sacrificing mechanical properties. The composite membrane shows significantly improved handleability and processability. This work sheds light on the design strategy for a safe electrolyte towards stable Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Controlled large-area lithium deposition to reduce swelling of high-energy lithium metal pouch cells in liquid electrolytes

Lithium (Li) metal battery technology, renowned for its high energy density, faces practical challenges, particularly concerning large volume change and cell swelling. Despite the profound impact of external pressure on cell performance, there is a notable gap in research regarding the interplay between external pressure and the electroplating behaviours of Li+ in large-format pouch cells. Here we delve into the impact of externally applied pressure on electroplating and stripping of Li in 350 Wh kg –1 pouch cells. Employing a hybrid design, we monitor and quantify self-generated pressures, correlating them with observed charge–discharge processes. A two-stage cycling process is proposed, revealing controlled pouch cell swelling of less than 10%, comparable to state-of-the-art Li-ion batteries. Finally, the pressure distribution across the cell surface unveils a complex Li+ detour behaviour during electroplating, highlighting the need for innovative strategies to address uneven Li plating and enhance Li metal battery technology.

25 ENERGY STORAGE↗
DOE OSTI2021

Selective dopant segregation modulates mesoscale reaction kinetics in layered transition metal oxide

Incorporation of foreign elements into the cathode material is broadly adopted by both academia and industry to improve the battery performance. The lack of an in-depth understanding for the underlying mechanism, however, makes it a largely try-and-error process with unsatisfactory efficiency and effectiveness. This is particularly true for the electrochemical reaction kinetics that is heterogeneous over a broad range of length scales and is determined collectively by the cathode’s electronic structure, lattice configuration, and micro-morphology. In this work, we unveiled a facet-dependent dopant segregation effect in Zr-modified single-crystal LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode. By forming kinetically favored corners on the cathode particles, the presence of a trace amount of Zr critically modulates the mesoscale reaction kinetics. Our findings suggest that a delicately controlled dopant distribution is a viable strategy for designing the next-generation battery cathode with superior structural and chemical robustness.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Grid-forming Control of Single- and Two-Stage Solar PV Systems with Mode Transition

Legacy power systems once dominated by con-ventional synchronous machines are transitioning into systems driven by fast-acting power-electronic converters that integrate renewable resources. The majority of integrated renewables such as PV and wind bring down system inertia and can cause stability issues due to their volatile nature. The state-of-the-art grid-forming (GFM) control is proven to enhance system inertia and stability in low-inertia systems. However, most of the existing GFM inverters are applied for battery systems, which are much more expensive than PV. Motivated by this, in this paper we propose a holistic grid-forming (GFM) control strategy for PV systems without the need of energy storage. The proposed strategy is developed on the secondary level of the grid-forming control that enables the PV inverter to operate smoothly among islanded, synchronization, GFM, and limited grid-forming (LGF) modes. The practical criteria for determining the operation modes are established and implemented based on the grid operation scenarios. Here, the proposed design is successfully validated by case studies with a laboratory prototype using Siemens Software Defined Inverters.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

A review of thermal physics and management inside lithium-ion batteries for high energy density and fast charging

Traditionally it has been assumed that battery thermal management systems should be designed to maintain the battery temperature around room temperature. That is not always true as lithium-ion battery (LIB) R&D is pivoting towards the development of high energy density and fast charging batteries. Therefore, it is necessary to have a comprehensive review of thermal considerations for LIBs targeted for high energy density and fast charging, i.e., the optimal thermal condition, thermal physics (heat transport and generation) inside the battery, and thermal management strategies. As the energy density and charge rate increases, the optimal battery temperature can shift to be higher than room temperature. In the first part of the review various sources of heat generation inside LIBs and various approaches to minimizing battery heat generation are summarized. The importance of heat of mixing due to ion diffusion during fast charging is also highlighted. To improve the temperature uniformity and avoid excessive internal temperature rise, heat transfer inside the battery needs to be enhanced, and reducing the thermal contact resistance between the electrodes and separator can significantly increase the effective thermal conductivity of batteries. In the second part of the review various challenges and latest developments related to thermal transport and properties of LIBs are discussed. Finally, a summary of latest advancement on smart control of internal temperature of LIBs is discussed as depending on the ambient temperature and the optimal temperature; the battery heat needs to be retained or dissipated to elevate or avoid temperature rise.

25 ENERGY STORAGE↗
DOE OSTI2025

Grid Resiliency with a 100% Renewable Microgrid

San Diego Gas & Electric Company (SDG&E) installed America’s first and largest utility-scale microgrid in Borrego Springs in 2013. The first generation Borrego Springs Microgrid utilized diesel generators to form and stabilize the microgrid island, with support from grid-scale batteries and local solar photovoltaic (PV) generation. In this project, SDG&E in partnership with National Renewable Energy Laboratory (NREL) demonstrated through modeling, simulation and utility field testing that blackstart and islanding of the microgrid can be led with 100% renewable, inverter based resources (IBRs), to help reduce community reliance on conventional generation resources. Through equipment upgrades, grid-forming island leader capability was transitioned to a battery IBR instead of the Borrego Springs Microgrid diesel generators. A new microgrid controller was integrated to the microgrid and programmed to control and manage multiple energy storage systems. Synchrophasor and other power quality data verified autonomous, high-speed response of the IBRs through blackstart, islanding, and load step testing. Results of project field evaluations provide distribution systems operators (DSO) with increased confidence that renewable, IBR can replace traditional generators to blackstart and island microgrids and rapidly establish stable island frequency with rapid changes in peak power demand. Importantly, the project validated the integration feasibility of a distributed energy resource management system (DERMS) controller that manages multiple grid-forming and grid-following IBRs, establishing a standard design interface to reduce the complexity of integrating new DERs in the future and supporting replication by the industry. As a result of learnings in this project, SDG&E has implemented the microgrid controller strategy at multiple other microgrid sites, thereby validating the replicability of the solution. Hardware-in-the-loop (HIL) simulations including power and controller HIL hardware — along with electromagnetic transient (EMT) simulations of Borrego Springs Microgrid —informed adjustments to inverter parameters and were important to characterize the performance of the IBRs in relevant operating conditions before deployment. The EMT and HIL simulations of islanding the entire community are important contributions in providing confidence in IBR performance prior to future islanding of the community in the field. High-fidelity EMT and/or HIL simulation of IBRs can de-risk field operations, and its relevance and importance as a tool is increasing as distribution grids and microgrids become more complex and dynamic with an increasing proportion of renewable generation, distributed energy storage, and two-way power and energy flows.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Power Electronics as an Enabler of the Current and Future Grid: Control Instead of Copper

Power electronics are becoming more pervasive in the power system. Solar, wind and battery energy storage systems regularly connect to the grid using power electronic interfaces. Loads are also increasingly power electronic-based. These changes, coupled with the change in the power system's operating characteristics as more and more renewable energy is integrated into the power system, offer a challenge to power electronic and power system engineers alike - how do we design and operate the power system moving forward?

direct connect↗
DOE OSTI2021

Correlating Catalyst Design and Discharged Product to Reduce Overpotential in Li-CO 2 Batteries

Li-CO 2 batteries with dual efficacy for greenhouse gas CO 2 sequestration and high energy output have been regarded as a promising electrochemical energy storage technology. However, battery feasibility has been hampered by inferior electrochemical performance due to large overpotentials and low cyclability primarily caused by the difficult decomposition of ultra-stable Li 2 CO 3 during charge. The use of cathode catalysts has been highlighted as a promising solution and catalyst properties, as well as the nature of discharge products, are closely correlated with electrochemical performance. Here, the catalyst design strategies that include active site enrichment, electrical transport enhancement, and mass transfer improvement are summarized. Catalyst effects on product decomposition are then subsequently introduced, while product geometry and chemical composition will be explored, with an emphasis on the formation/decomposition of Li 2 C 2 O 4 instead of Li 2 CO 3 . Building on previous research, future directions that facilitate improvements in catalyst design are put forward to reinforce the fundamental development of Li-CO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Battery detectives: Uncovering cathode impact on anode-free Li cell performance by operando NMR

Here, Anode-free Li-ion batteries could attain new levels of energy density, but challenges remain in controlling deposition and managing degradation. In this issue of Chem, Kwon et al. probe Li metal growth using operando NMR to unravel how cathode materials impact performance and establish criteria for the high-energy/low-cost design tradeoff.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Temperature-Dependent Fracture Resistance of Silicon Nanopillars during Electrochemical Lithiation

During the lithation of silicon anodes, the solid-state diffusion of lithium into Li x Si follows the Arrhenius law, the resulting morphology and fracture behavior are determined by the silicon anode operation temperature. Here, we reveal the temperature dependence of the lithiation mechanics of crystalline silicon nanopillars (SiNPs) via microscopic observations of the anisotropic growth and fracture behavior. In this work, we fabricated 1D SiNP structures with various orientations ($\langle100\rangle, \langle110\rangle$, and $\langle111\rangle$) as working electrodes and operated them at temperatures ranging from –20 to 40 °C. The lithiation of crystalline silicon at low temperatures exhibited preferential volume expansion along $\langle110\rangle$ and decreased fracture resistance. Furthermore, low temperatures caused the catastrophic fracture of amorphous silicon after the second lithiation. Our findings demonstrate the importance of silicon anode temperature control to prevent mechanical fracture during the cycle of lithium-ion batteries in harsh environments (e.g., electric vehicles in winter).

25 ENERGY STORAGE↗
DOE OSTI2021

Formation of Surface Impurities on Lithium–Nickel–Manganese–Cobalt Oxides in the Presence of CO 2 and H 2 O

Surface impurities involving parasitic reactions and gas evolution contribute to the degradation of high Ni content LiNi x Mn y Co z O 2 (NMC) cathode materials. The transient kinetic technique of Temporal Analysis of Products (TAP), density functional theory, and infrared spectroscopy have been used to study the formation of surface impurities on varying nickel content NMC materials (NMC811, NMC622, NMC532, NMC433, NMC111) in the presence of CO 2 and H 2 O. CO 2 reactivity on a clean surface as characterized by CO 2 conversion rate in the TAP reactor follows the order: NMC811 > NMC622 > NMC532 > NMC433 > NMC111. The capacity of CO 2 uptake follows a different order: NMC532 > NMC433 > NMC622 > NMC811 > NMC111. Moisture pretreatment slows down the direct CO 2 adsorption process and creates additional active sites for CO 2 adsorption. Electronic structure calculations predict that the (012) surface is more reactive than the ($10\bar{1}4$) surface for CO 2 and H 2 O adsorption. CO 2 adsorption leading to carbonate formation is exothermic with formation of ion pairs. The average CO 2 binding energies on the different materials follow the CO 2 reactivity order. Water hydroxylates the (012) surface and surface OH groups favor bicarbonate formation. Water creates more active sites for CO 2 adsorption on the ($10\bar{1}4$) surface due to hydrogen bonding. The composition of surface impurities formed in ambient air exposure is dependent on water concentration and the percentage of different crystal planes. Different surface reactivities suggest that battery performance degradation due to surface impurities can be mitigated by precise control of the dominant surfaces in NMC materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗