SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Forebody tangential blowing for control at high angles of attack

A feasibility study to determine if the use of tangential leading edge blowing over the forebody could produce effective and practical control of the F-18 HARV aircraft at high angles of attack was conducted. A simplified model of the F-18 configuration using a vortex-lattice model was developed to obtain a better understanding of basic aerodynamic coupling effects and the influence of forebody circulation on lifting surface behavior. The effect of tangential blowing was estimated using existing wind tunnel data on normal forebody blowing and analytical studies of tangential blowing over conical forebodies. Incorporation of forebody blowing into the flight control system was investigated by adding this additional yaw control and sideforce generating actuator into the existing F-18 HARV simulation model. A control law was synthesized using LQG design methods that would schedule blowing rates as a function of vehicle sideslip, angle of attack, and roll and yaw rates.

Kroo, I.↗

NASA NTRS1963

Dynamic Model Investigation of a 1/20 Scale Gemini Spacecraft in the Langley Spin Tunnel

The investigation was conducted in the Langley spin tunnel. The tunnel is an atmospheric wind tunnel with a vertically rising airstream in the test section and a maximum airspeed of approximately 90 feet per second. For this investigation, the model was hand launched into the vertically rising airstream. At times the model, both with and without a drogue parachute, was launched gently with as little disturbance as possible to determine what motions of the spacecraft were self-excited. At other times, the spacecraft with pre-deployed drogue parachute was launched into various spinning motions to determine the effectiveness of the drogue parachute in terminating these spinning motions. During drogue-parachute deployment tests, the spacecraft was launched into various spinning and tumbling motions and the drogue parachute was deployed. The motions of the model were photographed with a motion-picture camera, and some of the film records were read to obtain typical time histories of the model motion. The angles of attack indicated in the time histories presented are believed to be accurate within +/-1 degree. The mass and dimensional characteristics of the dynamic model are believed to be measured to an accuracy of: +/-1 percent for the weight, +/-1 percent for z(sub cg)/d, +/-15 percent for x (sub cg), and +/-5 percent for the moments of inertia. The towline and bridle-line lengths were simulated to an accuracy of +/-1 foot full scale.

Lee, Henry A.↗

DOE OSTI2023

Data-driven Vulnerability Analysis of Networked Pipeline System

This paper introduces an attack generation framework for evaluating the vulnerability of nonlinear networked pipeline systems. The vulnerability analysis is formulated as determining the presence of feasible attack sets, defined by boundary functions representing the effectiveness and stealthiness of attack signals with respect to the objective and attack detection module. The framework utilizes three data-driven models, including two discriminative models that learn the boundary functions and a generative model that produces elements of the feasible attack set. A new loss function ensures successful attack generation with high probability.

03 NATURAL GAS↗

DOE OSTI2021

Cybersecurity for Grid Connected eXtreme Fast Charging (XFC) Station (CyberX) (Final Scientific/Technical Report)

This report summarizes the activities conducted under the DOE VTO funded project DE- EE0008451, where ABB Inc. (ABB), in collaboration with Idaho National Laboratory (INL), APS Global (APS), and XOS Trucks (XOS) pursued the development of a cyber-resilient extreme fast charging (XFC) management system. This project entitled Cybersecurity for Grid Connected eXtreme Fast Charging (XFC) Station (CyberX) focuses on a resilient architecture for smart charging EV Supply Equipment (EVSE) device control and Coordinated Anomaly Detection System (CADS) features that can be added at the charging site depot level to increase cybersecurity. The project was split into two budget periods focused first on developing the threat model and resilient control concepts and second on testing, improving, and validating those developed resilient control algorithms and features with a focus on key vulnerabilities identified during the threat assessment portion of the project. During the first budget period of the CyberX project, the ABB led team focused on activities to identify, model, and quantitatively prioritize high-impact attack scenarios with potential cyber-physical effects while also modeling and developing concepts for a resilient control system that could securely address integration of DERs and other resources with EV charging. Development of the security focused XFC management system (XMS) was accomplished first by offline simulation using a developed XFC station or depot with 480V input level and simulating measurement inputs to monitoring and control systems in concept development. A representative distribution grid model was developed supporting an EV charging site model with BESS and 6 general EV charging models. These EV charging models allowed multiple configurations of charging level, multiple connected protection and measurement devices, and simulation function to show general compromise of EV, BESS, and protection features based on parallel threat analysis. During the second budget period, the EV site and supporting systems model was developed in more detail and converted from offline model to real-time to real-time with EV charging hardware in the loop (HIL). The resilient control architecture developed as concept in the first part of the project was further tested and validated for integration of local energy resources and XFC charging station site equipment while maintaining cybersecure operating principles. The proposed resilient architecture for smart charging and cybersecurity features consists of two main concepts developed and tested within the project. The first concept is an XFC management system (XMS) consisting of a hardware gateway, software platform, and Supervisory Control and Data Acquisition (SCADA) or Distribution Management System integration components. The second concept is a Coordinated Anomaly Detection System (CADS) which forms a primarily software-related subsystem of the total CyberX solution focused on monitoring system measurements, estimation of measurement states, and predicting current at the utility point of interaction based on machine learning for anomaly detection.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1981

Wing-alone aerodynamic characteristics at high angles of attack

An experimental investigation has been conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The family of wings tested varied in aspect ratio from 0.5 to 4.0 and taper ratio from 0.0 to 1.0. The wings were tested at angles of attack ranging from 0 to 60 deg and Mach numbers from 1.6 to 4.6. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surface. Comparison of these data with the limited available data from the literature indicate the present data are free of sting interference effects through the test range of angle of attack. Presented and discussed are results showing the effects of model geometry, Mach number and angle of attack on aerodynamic characteristics consisting of normal force, pitching moment, bending moment, longitudinal center-of-pressure locations, and lateral center-of-pressure locations.

Stallings, R. L., Jr.↗

NASA NTRS1984

Progress towards large wind tunnel magnetic suspension and balance systems

Recent developments and current research efforts leading towards realization of a large scale production wind tunnel Magnetic Suspension and Balance facility are reviewed. Progress has been made in the areas of model roll control, high angle-of-attack testing, digital system control, high magnetic moment superconducting solenoid model cores, and system failure tolerance. Formal design studies of large scale facilities have commenced and are continuing.

Britcher, C. P.↗

NASA NTRS2022

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures from a model of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft in the C612A configuration was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for two different mounting options: a swept blade strut that attached at the top of model ahead of the inlet, and rear-entry sting that was made as one piece with a dummy nacelle, and which had a 2”-long cylindrical segment aft of the nozzle exit before tapering up in size. The blade strut allowed for a clean aft end of the model for evaluation of the shocks from that region, while the sting avoided the significant distortions of the flow and shocks from the blade strut along the top of the model. Both the sting and the strut had adapters that attached to a force balance. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail horizontal surface. Off-body static pressure measurements of the flow field below the model were made by use of a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the wind tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the tunnel strut and the balance. The longitudinal positioning allowed multiple pressure signatures to be obtained along different portions of the rail. These signatures were aligned by accounting for the model longitudinal movement and then averaged to take out the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for all the variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

NASA NTRS2023

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

NASA NTRS2023

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

Sonic boom↗

NASA NTRS1980

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 2: High-wing model C

Aerodynamic characteristics obtained in a helical flow environment utilizing a rotary balance located in the Langley spin g tunnel are presented in plotted form for a 1/6 scale, single engine, high wing, general aviation model. The configurations tested included the basic airplane and control deflections, wing leading edge devices, tail designs, and airplane components. Data are presented without analysis for an angle of attack range of 8 deg to 90 deg and clockwise and counter clockwise rotations covering a spin coefficient range from 0 to 0.9.

Hultberg, R. S.↗

NASA NTRS1983

Determination of aerodynamic parameters of a fighter airplane from flight data at high angles of attack

A procedure for the estimation of airplane model structure and parameters is applied to data from a modern fighter airplane operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, and the estimation method. The results presented contain basic longitudinal characteristics of the airplane and the estimates of aerodynamic parameters in the yawing-moment equations. These estimates are obtained from small and large amplitude maneuvers. Because the latter set of data was not suitable for airplane identification, some of the large amplitude maneuvers were joined together and then partitioned into subsets according to the values of angle of attack. Each subset was then analyzed as a separate data set. Most of the estimated parameters and functions are in good agreement with the wind tunnel measurements. The estimated lateral parameters in the model equations also demonstrate good prediction capabilities.

Klein, V.↗

NASA NTRS1990

Application of variable-gain output feedback for high-alpha control

A variable-gain, optimal, discrete, output feedback design approach that is applied to a nonlinear flight regime is described. The flight regime covers a wide angle-of-attack range that includes stall and post stall. The paper includes brief descriptions of the variable-gain formulation, the discrete-control structure and flight equations used to apply the design approach, and the high performance airplane model used in the application. Both linear and nonlinear analysis are shown for a longitudinal four-model design case with angles of attack of 5, 15, 35, and 60 deg. Linear and nonlinear simulations are compared for a single-point longitudinal design at 60 deg angle of attack. Nonlinear simulations for the four-model, multi-mode, variable-gain design include a longitudinal pitch-up and pitch-down maneuver and high angle-of-attack regulation during a lateral maneuver.

Ostroff, Aaron J.↗

NASA NTRS1980

Consolidation of data base for Army generalized missile model

Data from plume interaction tests, nose mounted canard configuration tests, and high angle of attack tests on the Army Generalized Missile model are consolidated in a computer program which makes them readily accessible for plotting, listing, and evaluation. The program is written in FORTRAN and will run on an ordinary minicomputer. It has the capability of retrieving any coefficient from the existing DATAMAN tapes and displaying it in tabular or plotted form. Comparisons of data taken in several wind tunnels and of data with the predictions of Program MISSILE2 are also presented.

Klenke, D. J.↗

NASA NTRS1979

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 1: High-wing model B

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in a spin tunnel are presented in plotted form for a 1/6.5 scale, single engine, high wing, general aviation airplane model. The configurations tested included the basic airplane, various wing leading-edge devices, tail designs, and rudder control settings as well as airplane components. Data are presented without analysis for an angle of attack range of 8 deg to 90 deg and clockwise and counter-clockwise rotations covering an omega b/2V range from 0 to 0.85.

Bihrle, W., Jr.↗

NASA NTRS2015

Model Deformation Measurements of Sonic Boom Models in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel

The deformations of two sonic-boom models were measured by stereo photogrammetry during tests in the 9- by 7-Ft Supersonic Wind Tunnel at NASA Ames Research Center. The models were geometrically similar but one was 2.75 times as large as the other. Deformation measurements were made by simultaneously imaging the upper surfaces of the models from two directions by calibrated cameras that were mounted behind windows of the test section. Bending and twist were measured at discrete points using conventional circular targets that had been marked along the leading and trailing edges of the wings and tails. In addition, continuous distributions of bending and twist were measured from ink speckles that had been applied to the upper surfaces of the model. Measurements were made at wind-on (M = 1.6) and wind-off conditions over a range of angles of attack between 2.5 deg. and 5.0 deg. At each condition, model deformation was determined by comparing the wind-off and wind-on coordinates of each measurement point after transforming the coordinates to reference coordinates tied to the model. The necessary transformations were determined by measuring the positions of a set of targets on the rigid center-body of the models whose model-axes coordinates were known. Smoothly varying bending and twist measurements were obtained at all conditions. Bending displacements increased in proportion to the square of the distance to the centerline. Maximum deflection of the wingtip of the larger model was about 5 mm (2% of the semispan) and that of the smaller model was 0.9 mm (1% of the semispan). The change in wing twist due to bending increased in direct proportion to distance from the centerline and reached a (absolute) maximum of about -1 at the highest angle of attack for both models. The measurements easily resolved bending displacements as small as 0.05 mm and bending-induced changes in twist as small as 0.05 deg.

model deformation↗

DOE OSTI2020

Hydrolytic Aging in Rubber-Like Materials: A Micro-Mechanical Approach to Modeling

Abstract The effect of hydrolytic aging on mechanical responses of Rubber likes materials, in particular, Mullins effect and the permanent set has been modeled. Hydrolytic aging is considered as the result of the competition between two phenomena (1) chain scission and (2) cross-link scission/reformation. Both phenomena were modeled and thus, the strain energy of the polymer matrix is written with respect to three independent mechanisms; i) the shrinking original matrix which has not been attacked by water, ii) conversion of the first network to a new network due to the reduction of the crosslinks, and iii) energy loss from network degradation due to water attacks to ester groups. The model is validated with respect to a set of experimental data. Besides accuracy, the simplicity and few numbers of fitting parameters make the model a good choice for further implementations.

Bahrololoumi, Amir↗

NASA NTRS1994

Effects of vibration on inertial wind-tunnel model attitude measurement devices

Results of an experimental study of a wind tunnel model inertial angle-of-attack sensor response to a simulated dynamic environment are presented. The inertial device cannot distinguish between the gravity vector and the centrifugal accelerations associated with wind tunnel model vibration, this situation results in a model attitude measurement bias error. Significant bias error in model attitude measurement was found for the model system tested. The model attitude bias error was found to be vibration mode and amplitude dependent. A first order correction model was developed and used for estimating attitude measurement bias error due to dynamic motion. A method for correcting the output of the model attitude inertial sensor in the presence of model dynamics during on-line wind tunnel operation is proposed.

Young, Clarence P., Jr.↗

NASA NTRS1979

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 2: Low-wing model B

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the spin tunnel are presented in plotted form for a 1/6.5 scale, single engine, low wing, general aviation airplane model. The configurations tested included the basic airplane, various wing leading-edge devices, tail designs, and rudder control settings as well as airplane components. Data are presented without analysis for an angle-of-attack range of 8 deg to 90 deg and clockwise and counter-clockwise rotations covering an (omega)(b)/2V range from 0 to 0.85.

Bihrle, W., Jr.↗