SEARCH · Engineering Papers

Results for “additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

DOE OSTI2015

Effects of N{sub 2}O gas addition on the properties of ZnO films grown by catalytic reaction-assisted chemical vapor deposition

The influence of N{sub 2}O gas addition on the properties of zinc oxide (ZnO) films grown on a-plane (11–20) sapphire (a-Al{sub 2}O{sub 3}) substrates was investigated, using a chemical vapor deposition method based on the reaction between dimethylzinc and high-temperature H{sub 2}O produced by a catalytic H{sub 2}-O{sub 2} reaction on platinum (Pt) nanoparticles. The addition of N{sub 2}O was found to increase the size of the crystalline facets and to improve the crystal orientation along the c-axis. The electron mobility at 290 K was also increased to 234 cm{sup 2}/Vs following the addition of N{sub 2}O gas at a pressure of 3.2 × 10{sup −3 }Pa. In addition, the minimum full width at half maximum of the most intense photoluminescence peak derived from neutral donor bound excitons at 10 K decreased to 0.6 meV by the addition of N{sub 2}O gas at a pressure of 3.1 × 10{sup −2 }Pa.

36 MATERIALS SCIENCE↗

DOE OSTI2017

The Catalytic Effect of Electronegative Additives on Removal of Perchloroethylene Vapor from Air by Pulsed Corona Discharge

It is established that electronegative additives (CCl{sub 4}, freon-113) produce a catalytic effect on the conversion of volatile organic compounds (VOCs) under the action of atmospheric-pressure nonequilibrium plasma generated in pulsed corona discharge. At concentrations below 0.1%, these additives significantly decrease the discharge current, but the energy efficiency of the process of VOC removal from air increases. The catalytic effect of electronegative additives on the VOC conversion in air and nitrogen is quantitatively demonstrated in the case of perchloroethylene C{sub 2}Cl{sub 4} (PCE) vapor removal. The addition of 0.085% CCl{sub 4} to air reduces the energy consumption for PCE removal at initial concentration of 0.09% by half (from 12 to 6 eV per molecule) at a 63% degree of cleaning. Mechanisms explaining the active inf luence of electronegative additives on the discharge current and the process of impurity removal are suggested.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2016

Measurement of $\mathrm{ t \bar{t} } $ production with additional jet activity, including b quark jets, in the dilepton decay channel using pp collisions at $\sqrt{s} =$ 8 TeV

Jet multiplicity distributions in top quark pair (tt-bar) events are measured in pp collisions at a centre-of-mass energy of 8 TeV with the CMS detector at the LHC using a data set corresponding to an integrated luminosity of 19.7 fb -1 . The measurement is performed in the dilepton decay channels (e + e - ,μ + μ - and e ± μ ∓ ). Furthermore, the absolute and normalized differential cross sections for tt-bar production are measured as a function of the jet multiplicity in the event for different jet transverse momentum thresholds and the kinematic properties of the leading additional jets. The differential tt-barb and tt-barbb-bar cross sections are presented for the first time as a function of the kinematic properties of the leading additional b jets. Furthermore, the fraction of events without additional jets above a threshold is measured as a function of the transverse momenta of the leading additional jets and the scalar sum of the transverse momenta of all additional jets. Finally, the data are compared and found to be consistent with predictions from several perturbative quantum chromodynamics event generators and a next-to-leading ordercalculation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Design of a Scavenging Pyrrole Additive for High Voltage Lithium-Ion Batteries

We report 1-(dimethylamino) pyrrole (PyDMA) as an electrolyte additive for high voltage lithium-ion batteries based on LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)//Graphite with an upper cutoff voltage of 4.4 V. Density Functional Theory (DFT) modeling indicates that the unique structure of PyDMA could be effective in preventing the hydrolysis of LiPF 6 in a carbonate electrolyte, mitigating issues related to HF formation. The calculations also indicated that the additive would oxidize at lower potentials than typical electrolyte solvents, which could lead to protective films at the cathode surface. These expectations were tested using Nuclear Magnetic Resonance (NMR) and extensive electrochemical characterization. NMR studies confirmed the superb dehydrating capability of PyDMA, which successfully prevents HF formation even at high water content. Addition of 0.5 wt% PyDMA resulted in improved capacity retention in full-cells, and also in lower levels of transition metal dissolution from the cathode. Incremental capacity (dQ/dV) analysis indicates that benefits of PyDMA at low concentration (0.5–1 wt%) are associated with decreased rates of Li + -trapping reactions, and that higher concentrations of the additive can lead to isolation of cathode domains. Furthermore, our study indicates that PyDMA could be a promising electrolyte additive for high voltage lithium-ion batteries at a low concentration.

25 ENERGY STORAGE↗

DOE OSTI2022

Performance of a Novel In-Situ Converted Additive for High Voltage Li-ion Pouch Cells

In search for new classes of additives for high voltage NMC/graphite lithium-ion cells, the precursor additive bis(trimethylsilyl) malonate (bTMSM) is shown to be activated via a spontaneous reaction with LiPF 6 and LiBF 4 salts in carbonate-based electrolyte to form lithium tetrafluoro(malonato)phosphate (LiTFMP), and lithium difluoro(malonato)borate (LiDFMB), respectively. The reaction schemes and rates were studied via NMR spectroscopy and GCMS. The effects of LiTFMP and LiDFMB on high voltage electrochemical performance were then examined up to 4.5 V in Li[Ni 0.4 Mn 0.4 Co 0.16 ]O 2 (NMC442)/graphite and Li[Ni 0.6 Mn 0.4 Co 0.0 ]O 2 (NMC/640)/graphite pouch cells using aggressive voltage-hold cycling, long-term charge/discharge cycling, storage experiments, electrochemical impedance spectroscopy, and gas evolution measurements. While in situ converted additives suffer from gassing issues due to the presence of trimethylfluorosilane (TMSF) gas, a side product of the in situ reaction of bTMSM with LiPF 6 , the cycling and storage capability for the activated additives under study shows competitive performance and controlled impedance when compared to other well-known high voltage additives. Micro X-ray fluorescence spectroscopy (μXRF) confirmed that LiTFMP successfully minimizes the rate of transition metal deposition on the surface of graphite apparently by forming a protective agent at the cathode surface, hence allowing for improved cycling performance at high voltages.

25 ENERGY STORAGE↗

DOE OSTI2014

Effects of Substrate Addition on Soil Respiratory Carbon Release Under Long-Term Warming and Clipping in a Tallgrass Prairie

Regulatory mechanisms of soil respiratory carbon (C) release induced by substrates (i.e., plant derived substrates) are critical for predicting ecosystem responses to climate change, but the mechanisms are not well understood. In this study, we sampled soils from a long-term field manipulative experiment and conducted a laboratory incubation to explore the role of substrate supply in regulating the differences in soil C release among the experimental treatments, including control, warming, clipping, and warming plus clipping. Three types of substrates (glucose, C 3 and C 4 plant materials) were added with an amount equal to 1% of soil dry weight under the four treatments. We found that the addition of all three substrates significantly stimulated soil respiratory C release in all four warming and clipping treatments. In soils without substrate addition, warming significantly stimulated soil C release but clipping decreased it. However, additions of glucose and C 3 plant materials (C 3 addition) offset the warming effects, whereas C 4 addition still showed the warming-induced stimulation of soil C release. Our results suggest that long-term warming may inhibit microbial capacity for decomposition of C 3 litter but may enhance it for decomposition of C 4 litter. Such warming-induced adaptation of microbial communities may weaken the positive C-cycle feedback to warming due to increased proportion of C 4 species in plant community and decreased litter quality. In contrast, clipping may weaken microbial capacity for warming-induced decomposition of C 4 litter but may enhance it for C 3 litter. Warming- and clipping-induced shifts in microbial metabolic capacity may be strongly associated with changes in plant species composition and could substantially influence soil C dynamics in response to global change.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2016

Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheet material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture geometry using the EBM technology in order to compare deposition features such as surface roughness, geometric accuracy, deposition rate, surface and subsurface porosity, and material quality. It was determined that the laser powder bed technology was ideal for the geometry and requirements of the fixture set by Praxair, and Praxair moved forward with the purchase of a laser powder bed system. The subsequent portion of the project focused on determining the ideal processing parameters for alloy X for the laser powder bed system using ORNL’s Renishaw laser powder bed system. Praxair supplied gas atomized powders of alloy X material with properties specified by ORNL. ORNL printed text cube arrays in order to determine the ideal combination of laser powder and laser travel speed in order to maximize material density, improve surface quality, and maintain geometric accuracy. Additional powder supplied by Praxair was used to fabricate a full-scale fixture component.

42 ENGINEERING↗

DOE OSTI2016

Process Modeling for Additive Manufacturing

Additive Manufacturing (AM) provides a new avenue to design innovative materials and components that cannot be created using traditional machining operations. With current AM capabilities, complex designs (such as those required in weapon systems) can be readily manufactured with laser powder forming (or Laser-Engineered Net Shaping (LENSTM)) [1] that would be otherwise cost prohibitive or impossible to produce. However, before an AM product can be qualified for weapon applications, the characteristics of the metals produced by additive manufacturing processes need to be well understood. This work focuses on the development of computational simulation tools to model the metal additive manufacturing process. This work extends and integrates existing Sandia National Laboratories tools to accomplish the following: (i) be able to better predict residual stresses in AM product, (ii) extend high-fidelity material models to capture material evolution during the formation process, leading to prediction of end-state material properties, and (iii) provide a basis for engineering tools to propose improvements to additive manufacturing process variables, including those that minimize process variation. While this work in its current state is directly applicable to additive manufacturing processes, the tools developed may also help enable modeling welding processes such as gas tungsten arc (GTA), electron beam, and laser welding.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2019

Shortening the Design and Certification Cycle for Additively Manufactured Materials by Improved Mesoscale Simulations and Validation Experiments: Fiscal Year 2019 Status Report.

This report outlines the fiscal year (FY) 2019 status of an ongoing multi-year effort to develop a general, microstructurally-aware, continuum-level model for representing the dynamic response of material with complex microstructures. This work has focused on accurately representing the response of both conventionally wrought processed and additively manufactured (AM) 304L stainless steel (SS) as a test case. Additive manufacturing, or 3D printing, is an emerging technology capable of enabling shortened design and certification cycles for stockpile components through rapid prototyping. However, there is not an understanding of how the complex and unique microstructures of AM materials affect their mechanical response at high strain rates. To achieve our project goal, an upscaling technique was developed to bridge the gap between the microstructural and continuum scales to represent AM microstructures on a Finite Element (FE) mesh. This process involves the simulations of the additive process using the Sandia developed kinetic Monte Carlo (KMC) code SPPARKS. These SPPARKS microstructures are characterized using clustering algorithms from machine learning and used to populate the quadrature points of a FE mesh. Additionally, a spall kinetic model (SKM) was developed to more accurately represent the dynamic failure of AM materials. Validation experiments were performed using both pulsed power machines and projectile launchers. These experiments have provided equation of state (EOS) and flow strength measurements of both wrought and AM 304L SS to above Mbar pressures. In some experiments, multi-point interferometry was used to quantify the variation is observed material response of the AM 304L SS. Analysis of these experiments is ongoing, but preliminary comparisons of our upscaling technique and SKM to experimental data were performed as a validation exercise. Moving forward, this project will advance and further validate our computational framework, using advanced theory and additional high-fidelity experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Impacts of the Addition of Sodium Reactor Experiment (SRE) and DR-3 Fuel from H-Canyon to Tank 40 on Acid Stoichiometry and Hydrogen Production

H-Canyon plans to discard Sodium Reactor Experiment (SRE) material that is currently stored in Tanks 16.3 and 16.4. Savannah River Remediation (SRR) determined that a portion of the SRE material can be added to Sludge Batch 9 (SB9) in Tank 40 and the remainder will be added to Sludge Batch 10 (SB10) that is currently being prepared in Tank 51. A processing flowsheet for both the nitric-formic acid flowsheet and the nitric-glycolic acid flowsheet were previously developed for SB9 sludge-only and coupled operation with the Actinide Removal Process – Modular Caustic Side Solvent Extraction Unit (ARP-MCU) and the Salt Waste Processing Facility (SWPF). Due to the compositional change in Tank 40 after the addition of SRE material, it is necessary to determine the influence on the acid stoichiometry operating window and hydrogen production for SB9 processing. An assessment was completed to address the influence of an addition of SRE and DR-3 Fuel from H-Canyon on the chemistry of Tank 40, the defined acid stoichiometry window (with and without SWPF streams) for the nitric-formic and nitric-glycolic acid flowsheets, and the resulting influence of the hydrogen production. Hydrogen production during the SRAT/SME cycles consists of thermolytic, radiolytic, and catalytic hydrogen. For the nitric-formic acid flowsheet, catalytic hydrogen dominates the hydrogen production during DWPF operation mode for the SRAT and SME vessels. This report was written to summarize that assessment. No SRNL testing is needed prior to adding up to 7,100 additional gallons of SRE and DR-3 Fuel from H-Canyon to Tank 40. Also, the addition of SRE will not exceed the Shielded Cells reported values for catalytic hydrogen for either the nitric-formic acid flowsheet (Technical Safety Requirement (TSR) limit of 0.15 lb/h) or the nitric-glycolic acid flowsheet (TSR limit 0.024 lb/h). The addition of the ARP stream from SWPF and the use of the nitric-glycolic acid flowsheet are both expected to decrease hydrogen generation, leading to a larger safety margin in the CPC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Assessment of the 3420 Building Filtered Exhaust Stack Sampling Probe Location: Stack Verification Following Fan and Air Blender Additions

The Pacific Northwest National Laboratory (PNNL) 3420 Building, which is part of the Physical Sciences Facility (PSF), houses radiological capabilities that results in the requirement that emissions monitoring must be conducted for potential radionuclides in the exhaust air discharge of this building. The air monitoring system is required to conform to Title 40 of the Code of Federal Regulations part 61 (40 CFR 61) Subpart H, which in turns requires a sampling probe in the exhaust stream to conform to the criteria of American National Standards Institute / Health Physics Society (ANSI/HPS) N13.1-2011, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. To support the air emissions permit for the 3420 Building on the PNNL campus, stack testing that used computational fluid dynamics (CFD) modeling as a surrogate stack and verification tests of velocity uniformity and flow angle on the retrofitted facility stack was performed. The ANSI/HPS N13.1-2011 criteria for the air monitoring probe location are that velocity uniformity, gaseous tracer uniformity, and particulate tracer uniformity must be less than or equal to 20%COV. Furthermore, no point in the sampling location may have a gaseous tracer concentration that varies from the mean concentration by more than 30%. Additionally, the flow angle at the sampling location must not be more than 20°. The CFD modeling of the stack, as reported by Recknagle et al. (2018) demonstrated that the stack meets the criteria at the probe location. The velocity uniformity and flow angle results from the 3420 stack verification tests, performed in October 2020, demonstrated that the CFD model results may be used to support the qualification of the stack sampling location. The measured velocity uniformity verification test result was 1.4%COV. This value is well within the uniformity criterion, which is that the velocity uniformity be =20%COV. Additionally, this value is well within the criterion that the actual stack measurement must be within 5% of the surrogate stack result of 2.1%COV when all four fans were operating. Additionally, the measured average flow angle at the 3420 stack monitor location was 15.5 degrees. Although this is higher than expected based on the CFD model, the result is =20 degrees, so the criterion is met. Based on these stack verification test results, the reconfigured 3420 Building filtered exhaust stack meets the qualification criteria given in the ANSI/HPS N13.1-2011 standard. Further changes to the system configuration or operating conditions that are outside the bounds described in this and the CFD report (Recknagle et al., 2018) may require additional tests and additional analysis to determine compliance with the standard.

3420 Building↗

DOE OSTI2020

Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

This joint project among ORNL, GM, and DRO successfully developed ionic liquid-additized low viscosity lubricants, SAE 0W-12 and 70W-80, for both IC engine and rear axle lubrication, respectively, and demonstrated combined vehicle fuel economy improvement (FEI). Phosphonium-alkylphosphate ILs have been found to be the most effective among the candidates in protecting surface damage from both sliding wear and rolling contact fatigue, and optimal IL concentrations have been determined. The IL’s impact on three-way catalyst seems to be significantly less adverse than the conventional ZDDP. Oil formulations were optimized for both energy efficiency and wear protection. Tribological bench testing of the IL-additized low-viscosity oils showed at least 40% lower boundary friction, more than 60% lower elastohydrodynamic friction, and greater than 50% less wear compared with commercial baselines. IL-additized lubricants have demonstrated FEI by 9.9% in engine dynamometer tests under extreme conditions and 6.9% increased power output in gear rig tests. Prototype IL-additized engine oil and rear axle fluid exhibited combined FEI of 1.39% and 3.24% benchmarked against the state-of-the-art baselines in vehicle testing of fresh oils under the Federal Test Procedure (FTP) city cycle and Highway Fuel Economy Driving Schedule (HWFET), respectively. Used oil analysis suggested that the IL-additized low-viscosity oils produced less wear than the commercial baselines. The gained fundamental understanding and demonstrated FEI in this work pave the way for future development and implementation of the ionic liquid technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Study of Additive Manufacturing Applications to Geothermal Technologies Final Project Report

This report summarizes work performed to assess the potential for utilizing additive manufacturing (AM) to substantially improve either the availability, performance or cost basis for tools and components that are required for geothermal energy production. A systematic cataloging of geothermal activities, associated technologies, and current manufacturing methods was first undertaken. This included literature reviews as well as interviews with subject matter experts, service companies and OEMs. An industry workshop was held as part of this portion of the project to obtain input and concerns from a broad range of OEMs, service providers and end users. This workshop was also used to gage the current level of AM activity in industry, receptiveness to the use of AM manufactured parts, and any up front concerns that may exist. A summary of the workshop is presented in this report. Representative components and assemblies and their current manufacturing methods were then analyzed by additive manufacturing experts at a company called Senvol to determine the feasibility and required steps for producing parts by additive manufacturing. A step by step description of conventional manufacturing of the parts was also performed to establish a manufacturing baseline for comparison purposes. This analysis also considered and described the benefits of additively manufacturing the parts in terms of specific AM systems, material availability for AM, dimensional requirements and potential economic advantages. Details of the manufacturability assessment were summarized in a report which is included as a chapter in this document. The analysis of the AM subject matter experts was then be used by techno-economic analysts to perform a comparative economic evaluation of the manufacturing of select technologies by AM and conventional approaches. This activity leveraged ORNL expertise and prior experience in other applications. A framework based on assessing cost, volume production considerations, and time to manufacture was created to more easily discern the advantages or disadvantages of additive versus conventional manufacturing methods. The report concludes with a general assessment of the current applicability of AM for geothermal technologies, AM gaps and needs related to typical geothermal hardware, and the potential benefits and impacts of AM to geothermal energy production.

15 GEOTHERMAL ENERGY↗

DOE OSTI2021

Computational Tools for Additive Manufacture of Tailored Microstructure and Properties

Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Currently most additive builds use a single set of process parameters (e.g. laser power and scan speed) which results in a part with a homogenous microstructure that provides a singular performance level. To move beyond this state, Raytheon Technologies Research Center worked to create a set of computational tools to track material evolution through each step of the additive process. Computational fluid dynamics and phase field models for microstructure evolution as a function of processing parameters, and crystal plasticity models fully coupling microstructure and mechanical properties for performance predictions were leveraged to establish a connection between additive parameters and the final microstructure. This framework was utilized to tailor spatially-varying mechanical properties in a part by appropriately controlling the microstructure evolution during the additive process. Specifically, a turbine blade was 3D printed from nickel superalloy IN718 using laser powder bed fusion with coarse grains in the airfoil section which experiences the highest temperatures and is creep limited while finer grains were printed in the root of the blade which experience higher stresses but at lower temperatures and is therefore fatigue limited. The benefit of being able to intentionally insert coarse grains in the high temperature region of the blade was showcased with a microstructure sensitive creep model that indicates longer creep life for coarser grains.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

Integral Experiment Final Design for Thermal/Epithermal eXperiments (TEX) Plutonium Additional Mixed Spectrum Configurations

This report presents the final design (CED-2) for three additional mixed-spectra configurations for plutonium Thermal/Epithermal eXperiments (TEX) to target the intermediate energy region (IER-553). The baseline cases of IER-184 (PU-MET-MIXED-002 [2]) spanned the entire fission energy spectrum. Case 3, which had a median fission energy (MFE) of approximately 6E-5 MeV and had a fission fraction of about 42% in the intermediate energy range, resulted in a $k_{eff}$ overestimation of 1.1%. Compared to 749 previous ICSBEP plutonium benchmarks, the baseline cases accurately predicted the experiments in the thermal and fast regions where the majority of benchmarks inhabit. The benchmarks in the intermediate energy region to date are sparse and overestimate $k_{eff}$ with an average C/E between 1.02 and 1.03. The additional proposed configurations span the whole of the intermediate energy region. The experimental design utilizes the plutonium/aluminum metal alloy Zero Power Physics Reactor (ZPPR) Plutonium-Aluminum No-Nickel (PANN) plates with varying polyethylene moderator thicknesses to span the intermediate fission energy region. Each of the cases have varying fractions of thermal, intermediate, and fast fissions. The designs were chosen to maximize the intermediate energy fraction. The experiment will take place on the universal critical assembly machine, Planet. The layers will be split as equally as possible between the lower platen and the upper stationary platform of Planet. The upper half of the experimental configuration will also have an upper reflector of polyethylene of specified thicknesses to achieve criticality when the lower platen is raised fully. The previous IER-184 configurations, specifically Case 3, were used to determine the configurations for the additional experiments and neutronics calculations were used to fine-tune the configurations to ensure criticality. The quadrature sum uncertainty in Δ$k_{eff}$ for Case 3 in PU-MET-MIXED-002 was found to be 0.00219. Section 3.8 gives a detailed description of the uncertainties calculated. The additional configurations, which are based directly on Case 3, are expected to have similar uncertainties. However, it is possible to reduce the overall uncertainty of Δ$k_{eff}$ for the additional configurations using the knowledge obtained from the calculations in the benchmark.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Use of Modeling and Experiments to Assess the Effect of Minor Alloying Additions on Alumina Scale Formation during High-Temperature Oxidation

During the last decades, new generations of Ni-based superalloys have emerged with judiciously controlled chemistries. These alloys heavily rely on the addition of refractory elements to enhance their mechanical properties at elevated temperatures; however, a clear interpretation of the influence of these minor-element additions on the alloy's high-temperature oxidation behavior is still not well understood, particularly from the standpoint of predicting the transition from internal to external alumina formation. In this context, the present investigation describes a systematic study that addresses the intrinsic effects that minor element additions of Nb, Ta, and Re have on the oxidation behavior of alumina-scale forming γ-Ni alloys. By combining a novel simulation approach with high-temperature oxidation experiments, the present study evidences the generally positive effect associated with 2 at. % addition of Ta and Re as well as the detrimental consequences of Nb additions on the 1100 °C oxidation of (in at. %) Ni-6Al-(0,4,6,8)Cr alloys.

Rodriguez, Rafael↗

DOE OSTI2018

Fast Ultrasonic Imaging with Total Focusing Method (TFM) for Inspection of Additively Manufactured Polymer Composite Component

Ultrasonic adaptive imaging based on the phased-array technology and the synthetic focusing algorithm Total Focusing Method (TFM) is proposed for fast ultrasonic nondestructive evaluation of additively manufactured composite materials. Nondestructive evaluation and inspection of additively manufactured parts and components are necessary for quality assurance of the materials. Effective detection of defects and anomalies in manufactured parts prevents extra cost and production time. However, there are several limitations encountered when using conventional methods of nondestructive inspection for as built additively manufactured parts due to surface conditions and geometrical complexity. Post-processing operations, such as machining, are usually needed to detect possible defects such as layer disband, micro-cracks, and voids in the composite parts. The capability of aperture focusing in phased array ultrasonic methods provides the opportunity for the adjustment of the delay laws in ultrasonic beams and reduces the noise and beam distortion for better imaging. An additively manufactured carbon fiber reinforced Acrylonitrile Butadiene Styrene (ABS) composite sample with artificial side and bottom-drilled holes of different sizes, used to represent defects, was successfully inspected using the Total Focusing Method (TFM). Unlike conventional ultrasonic techniques, results show a promising way to provide inspection of as built additively manufactured composite parts with rough surface finishes. The proposed method helps to decrease inspection time and eliminate extra machining and preparation costs.

Taheri, Hossein↗

NASA NTRS1972

Effects of additives on volume change on melting, surface tension, and viscosity of liquid aluminum oxide

The effects of various oxide additives on the volume change on melting, the surface tension, and the viscosity of liquid Al2O3 were studied. Additives of Sm2O3, MgO, and Y2O3 which form solid solutions, compounds, and multiphase solids with Al2O3 were studied. A review of the property data for Al2O3 and Al2O3 containing oxide additives is presented. Oxide additives to Al2O3 reduce the volume change on melting and with the exception of SiO2 lower the viscosity; surface tensions change with oxide additives, but changes vary with different container material. Viscosity and volume change on melting appeared to be significantly more important for studying the properties of liquid oxides than surface tension. Supercooling of 270 K of yttrium aluminum garnet was observed.

Bates, J. L.↗