Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ti”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

The gamma-gamma prime region of the Ni-Al-Cr-Ti-W-Mo system at 850 C

The compositional limits of gamma and gamma-prime phases in nickel-base superalloys are determined experimentally. It is found that gamma-prime had the following range of compositions for the various elements contained in this phase: 72.1 to 78.0 at.% Ni; 7.8 to 17.3 at.% Al; 1.5 to 8.9 at.% Cr; 0.3 to 13.9 at.% Ti, 0.0 to 3.9 at.% Mo, and 0.0 to 7.2 at.% W. The composition of gamma varied as follows: Ni is balanced; 1.9 to 15.4 at.% Al; 6.6 to 30.7 at.% Cr; 0.0 to 3.1 at.% Ti; 0.0 to 8.7 at.% Mo; and 0.0 to 5.0 at.% W. W additions to the gamma appeared to increase somewhat the solubility of Al in this phase. Mo and W added together decreased the solubility of Al in gamma.

Dreshfield, R. L.↗
NASA NTRS1975

Growth of surface and corner cracks in beta-processed and mill-annealed Ti-6Al-4V

Empirical stress-intensity expressions were developed to relate the growth of cracks from corner flaws to the growth of cracks from surface flaws. An experimental program using beta-processed Ti-6Al-4V verified these expressions for stress ratios, R greater than or equal to 0. An empirical crack growth-rate expression which included stress-ratio and stress-level effects was also developed. Cracks grew approximately 10 percent faster in transverse-grain material than in longitudinal-grain material and at approximately the same rate in longitudinal-grain mill-annealed Ti-6Al-4V. Specimens having surface and corner cracks and made of longitudinal-grain, beta-processed material were tested with block loads, and increasing the stresses in a block did not significantly change the crack growth rates. Truncation of the basic ascending stress sequence within a block caused more rapid crack growth, whereas both the descending and low-to-high stress sequences slowed crack growth.

Bell, P. D.↗
NASA NTRS1976

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

Results are presented for an experimental study intended to provide sustained load crack growth (SLCG) data for Ti-6Al-4V titanium alloy tanks containing MIL-P-26536 hydrazine and refined hydrazine. Fracture mechanics data on crack growth threshold for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones (HAZ) are presented. All tests were made on uniaxially loaded fracture mechanics specimens involving part-through cracks, and an electrical discharge machined notch was used to start the crack. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are obtained for the temperature range 40-71 C. Major conclusions are that extreme susceptibility to SLCG in hydrazine is a universal property of unaged weld metal in Ti-6Al-4V titanium alloy of normal interstitial content, and that aging both weld metal and HAZ at 510 C for 4 hr after welding completely removes all susceptibility to SLCG induced by hydrazine, with less susceptibility to SLCG in refined hydrazine.

Lewis, J. C.↗
NASA NTRS1977

Volatile products in the corrosion of Cr, Mo, Ti and four superalloys exposed to O2 containing H2O and gaseous NaCl

Cooled target collection techniques were used to study the formation of volatile products when samples of Cr, Ti, IN-738, 713C, NASA-TRW VIA and B-1900 were exposed, at elevated temperatures, to oxidizing environments containing H2O(g) and NaCl(g). Samples were heated to 1050 C in one atmosphere of slowly flowing oxygen, saturated with water at 21 C, and containing about 50 ppm NaCl(g). Volatile products were detected for all materials except B-1900 and Ti. High pressure mass spectrometric sampling was used to directly identify volatile products emanating from samples of Cr and IN-738 subject to the above environments.

Fryburg, G. C.↗
NASA NTRS1977

Investigation of the fracture mechanism in Ti-5Al-2.5Sn at cryogenic temperatures

The influence of microstructure on the fracture mechanism and plane-strain fracture toughness of Ti-5Al-2.5Sn was studied through the use of fractography and metallographic sectioning techniques. One-inch thick plates of extra low interstitial (ELI) and normal interstitial Ti-5Al-2.5Sn were mill annealed at 815 C followed by either air or furnace cooling. These variations in composition and cooling rate resulted in differences in the volume fraction and internal structure of the iron-stabilized phase, and in the crystallographic texture and ordering of the alpha matrix. The tensile properties of these plates were determined at 20 K, 77 K, and 295 K. The air-cooled ELI plate was the toughest material evaluated.

Vanstone, R. H.↗
NASA NTRS1976

Cross sections for He and Ne isotopes in natural Mg, Al, and Si, He isotopes in CaF2, Ar isotopes in natural Ca, and radionuclides in natural Al, Si, Ti, Cr, and stainless steel induced by 12- to 45-MeV protons

Stacks of thin Mg, Al, Si, Ca, CaF2, Ti, and stainless steel foils were bombarded in twelve irradiations by a variable energy cyclotron. Cross sections are reported for He and Ne in natural Mg, Al, and Si, and for He in CaF2, and for Ar in natural Ca, as determined from mass spectrometer analysis of the inert gases. In addition, cross sections of Na-22 in natural Al and Si, of V-48 in natural Ti, and of Cr-51, Mn-52, and Co-57 in stainless steel are reported. From these were deduced Cr-51 and Mn-52 cross sections in natural Cr.

Walton, J. R.↗
NASA NTRS1977

Very low Ti /VLT/ basalts - A new mare rock type from the Apollo 17 drill core

Phaneritic fragments, vitrophyres, and glass beads of a new very low Ti (VLT) mare basalt are found in the Apollo 17 drill core. VLT lithic fragments are characterized by TiO2 content of approximately 0.5%, Mg/(Mg + Fe) of approximately 0.52, CaO/Al2O3 of approximately 0.9, and low alkali content. Although mineral systematics and modal composition of VLT basalt are similar to Apollo 12 and 15 low Ti basalts, VLT basalts cannot be related to these mare basalts by crystal fractionation. Since VLT basalt is isochemical with some of the less mafic green glasses, fractionation of VLT magma from a liquid of green-glass composition is a possibility. Spectral reflectance studies suggest that VLT-type basalts may be relatively common in mare basins.

Vaniman, D. T.↗
NASA NTRS1975

On the origin of high-Ti mare basalts

Analyses were conducted of sixteen Apollo 17 mare basalts for alkali, alkaline-earth, and rare-earth elements, Co, and Sc. The obtained data were utilized in a study concerning the nature of the igneous processes responsible for the chemical variations among the high-Ti, low-K basalts. Estimates were obtained regarding the abundances of the large-ion, lithophile elements in the source regions for the basalts. It is shown that the source regions could plausibly have been produced by processes believed to have occurred during the early history of the moon. Attention is given to chemical variations among the Apollo 17 mare basalts, near-surface (low-pressure) crystal fractionation, partial melting, limits on the extent of partial melting, and a summary of possible events leading to formation of high-Ti mare basalts.

Shih, C.-Y.↗
NASA NTRS1978

Fracture resistance of Ti-5Al-2.5Sn extra-low interstitial castings

Fracture toughness and cyclic crack propagation data for Ti-5Al-2.5Sn extra-low interstitial (ELI) castings, 0.51 and 2.54 cm (0.20 and 1.00 in.) thick, at 394, 294, 77, and 20 K (250, 70, -320, and -423 F), are presented. Both surface flaw and compact tension geometries were tested. Comparison is made with other titanium alloys in both wrought and cast forms. Crack propagation resistance is comparable to wrought Ti-5Al-2.5Sn ELI, even with the extremely coarse as-cast grain size encountered.

Fiftal, C. F.↗
NASA NTRS1979

L-series satellite spectra in Ti XII and Fe XVI

Transitions in Na-like Ti and Fe ions, which appear as satellites to 2p-3s and 2p-3d transitions in Ne-like ions, were studied. The soft X-ray spectra produced by a focused-laser source and a vacuum-spark device were obtained with the same grazing-incidence spectrograph. Atomic structure calculations agreed with the observed 2p-3s spectral patterns and made possible line identifications in Ti XII and Fe XVI.

Burkhalter, P. G.↗
NASA NTRS1979

Spectra of Fe-Ti silicate glasses - Implications to remote-sensing of planetary surfaces

Optical spectra of synthetic Fe-Ti silicate glasses and the temperature variations of the spectral features were investigated. The spectra are assigned to absorptions due to crystal field (CF) transitions in Ti(3+), Fe(2+) in octahedral coordination, and Fe(2+) in tetrahedral coordination, and to metal-metal and oxygen-metal charge transfer (CT) transitions which contribute to the near ultraviolet absorption edge. Temperature variations of the optical bands have been studied to explore implications for remote sensing. Caution is urged in the use of the absorption edge as a measure of TiO2 concentrations on planetary surfaces and in regolith samples.

Nolet, D. A.↗
NASA NTRS1980

Cl, P2O5, U and Br associated with mineral separates from a low and a high Ti mare basalt

Low Ti basalt 12040 and high Ti basalt 75055 have approximately the same Cl/P2O5 ratio; the Cl is that remaining after a hot water leach. Pyroxene, plagioclase and ilmenite minerals separated from the basalts also tend to have this same Cl/P2O5 ratio. This is evidence that these major minerals do not control the ratio since Cl and P would not be expected to partition to the same extent into each mineral. Olivine appears to be a special case. It is proposed that the grains measured contained inclusions with leachable and P2O5-related Cl. Dilute acid leaches of whole rock and separated minerals have the same or nearly the same Cl/P2O5 ratios as the residual samples. Apatite and whitlockite were probably the phases leached. They must be constituents of the mesostasis and are present as microminerals or coatings on major mineral grains. The acid leach results imply little or no partition of Cl and P2O5 into major minerals.

Jovanovic, S.↗
NASA NTRS1983

Stress-corrosion crack-growth study of titanium alloy Ti-6Al-4V exposed to freon PCA and nitrogen tetroxide MON-1

An experimental fracture mechanics program was performed to determine the stress corrosion crack growth sensitivity of the propellant tank material, titanium alloy Ti-6Al-4V, for aerospace satellite applications involving long term exposure to Freon PCA and nitrogen tetroxide MON-1. Sustained load tests were made at a 49 C (120 F) constant temperature using thin gauge tensile test specimens containing semielliptical surface flaws. Test specimen types included parent metal, center of weld, and weld heat affected zone. It was concluded that Ti-6Al-4V alloy is not adversely affected in a stress environment when exposed to Freon PCA for 1000 hours followed by exposure to nitrogen tetroxide MON-1 for 2000 hours at stress levels up to 80% of the experimental critical plane strain stress intensity factor.

Bjorklund, R. A.↗
NASA NTRS1984

Effect of creep in titanium alloy Ti-6Al-4V at elevated temperature on aircraft design and flight test

Short-term compressive creep tests were conducted on three titanium alloy Ti-6Al-4V coupons at three different stress levels at a temperature of 714 K (825 F). The test data were compared to several creep laws developed from tensile creep tests of available literature. The short-term creep test data did not correlate well with any of the creep laws obtained from available literature. The creep laws themselves did not correlate well with each other. Short-term creep does not appear to be very predictable for titanium alloy Ti-6Al-4V. Aircraft events that result in extreme, but short-term temperature and stress excursions for this alloy should be approached cautiously. Extrapolations of test data and creep laws suggest a convergence toward predictability in the longer-term situation.

Jenkins, J. M.↗
NASA NTRS1983

The effects of Cr, Al, Ti, Mo, W, Ta, and Cb on the cyclic oxidation behavior of cast Ni-base superalloys at 1100 and 1150 C

Fifty Ni-base superalloys with concentrations of Cr, Al, Ti, Mo, W, Ta, and Cb systematically varied between two nonzero levels, were tested for cyclic oxidation resistance at 1100 and 1150 C. Oxidation resistance was interpreted in terms of the rate of specific weight change and the types of oxides formed. It is found that the resistance of the alloys to cyclic oxidation is largely determined by Al content, with a sharp increase in the oxidation resistance observed in the Al concentration range 5-8 at. pct. The effects of the other elements studied were small compared with that of aluminum. Best oxidation resistance characteristics were predicted for high Al (13 at. pct), low Cr (10 at. pct), low Ti (2 at. pct), low Cb (1 at. pct), and high Mo, W, and Ta (3 at. pct each). The effects of the refractory metals, however, are somewhat ambiguous and should be investigated further. Higher boron contents, which were unintentionally varied, were clearly detrimental even for the most resistant compositions.

Barrett, C. A.↗
NASA NTRS1985

Selected fretting-wear-resistant coatings for Ti-6 pct Al-4 pct V alloy

The ability of several wear-resistant coatings to reduce fretting in the Ti-6Al-4V alloy is investigated. The experimental apparatus and procedures for evaluating fretting in uncoated Ti-6Al-4V alloy and in the alloy with plasma-sprayed coatings, polymer-bonded coating, and surface treatments are described. The wear volume and wear rate for the alloys are measured and compared. It is concluded that Al2O3 with 13 percent TiO2, preoxidation and nitride surface treatments, and MoS2 sputtering result in wear-resistant surfaces; however, the polyimide coating is the most wear resistant coating in both dry and moist air, and it causes the least wear to the uncoated alloy surface.

Bill, R. C.↗
NASA NTRS1986

Evaluation of Ti-6Al-4V surface treatments for use with a polyphenylquinoxaline adhesive

Three surface treatments for Ti-6Al-4V adherends were evaluated using a thermoplastic polymer monoether polyphenylquinoxaline, MEPPQ, which had been shown in previous studies to have good potential as a high temperature adhesive for aerospace applications. Initial results based on long term thermal exposure at 232 C (450 F) using the phosphate-fluoride (PF) and chromic acid anodized (CAA) treatments with MEPPQ adhesive were not encouraging. A significant improvement in strength retention and a change in failure mode (cohesive) at 232 C (450F) was found for the SHA treated specimens compared to the PF and CAA treatments. Although an improvement in long term thermal durability was obtained with the SHA treatment of Ti-6Al-4V, an improved surface treatment with better long term durability is still required for aerospace applications.

Progar, D. J.↗
NASA NTRS1987

Shot peening for Ti-6Al-4V alloy compressor blades

A text program was conducted to determine the effects of certain shot-peening parameters on the fatigue life of the Ti-6Al-4V alloys as well as the effect of a demarcation line on a test specimen. This demarcation line, caused by an abrupt change from untreated surface to shot-peened surface, was thought to have caused the failure of several blades in a multistage compressor at the NASA Lewis Research Center. The demarcation line had no detrimental effect upon bending fatigue specimens tested at room temperature. Procedures for shot peening Ti-6Al-4V compressor blades are recommended for future applications.

Carek, Gerald A.↗