SEARCH · Engineering Papers

Results for “Thermal Protection System (TPS)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Silica heat shield sizing

The sensitivity of silica heat shield requirements to gap width, tile edge radius, and heat transfer distribution within tile gaps was investigated. A two-dimensional thermal model was modified and used to determine the effect of two dimensional heat transfer distributions at high temperature reusable surface insulation edges on shuttle thermal protection system (TPS) requirements. The sensitivity of TPS requirements to coating thickness, emissivity, substructure thickness, and changes in gap heating for several locations on shuttle was also studied. An inverse solution technique was applied to temperature data obtained in the Ames 20 MW turbulent duct in order to examine the effect of tile edge radius on TPS requirements. The derived heating values were then used to predict TPS requirements. Results show that increasing tile radius reduces TPS requirements.

Ebbesmeyer, L. H.↗

NASA NTRS1977

Radiative metallic thermal protection systems - A status report

During the early stages of the space shuttle program there were a number of technological uncertainties concerning the applicability of metallic thermal protection systems (TPS) to the multimission environment of the shuttle. To resolve the uncertainties and to advance the state-of-the-art, the NASA-Langley Research Center initiated a broad-based technology program to develop metallic TPS over the temperature range from 810 K to 1590 K. Wind tunnel tests conducted to assess the influence of surface/stream interaction of wavy surfaces on the design of metallic TPS indicate small increases in heat flux and surface drag for flow angles less than 20 deg. Analytical and experimental investigations, recently completed, have significantly improved prediction methods for cyclic creep behavior of TPS components repeatedly exposed to complex mission cycles. Thermal/structural concept optimization studies to minimize mass while maintaining structural integrity have led to advanced designs with unit masses which are competitive with those for shuttle RSI. In addition, the durability and reusability of metallic TPS have been repeatedly demonstrated in tests of full-scale systems. The current state-of-the-art strongly suggests that radiative metallic TPS have come of age.

Bohon, H. L.↗

NASA NTRS1978

Design and fabrication of metallic thermal protection systems for aerospace vehicles

A program was conducted to develop a lightweight, efficient metallic thermal protection system (TPS) for application to future shuttle-type reentry vehicles, advanced space transports, and hypersonic cruise vehicles. Technical requirements were generally derived from the space shuttle. A corrugation-stiffened beaded-skin TPS design was used as a baseline. The system was updated and modified to incorporate the latest technology developments and design criteria. The primary objective was to minimize mass for the total system.

Varisco, A.↗

NASA NTRS1979

Technology and operational considerations for low-heat-rate trajectories

A broad parametric study which examines several critical aspects of low-heat-rate entry trajectories is performed. Low planform loadings associated with future winged earth-entry vehicles coupled with the potential application of metallic thermal protection systems (TPS) suggest that such trajectories are of particular interest. Studied are three heating conditions - reference, stagnation, and windward centerline, for both laminar and turbulent flow; configuration-related factors including planform loading and hypersonic angle of attack; and mission-related factors such as cross-range and orbit inclination. Results indicate benefits in the design of TPS to be gained by utilizing moderate angles of attack as opposed to high-lift coefficient, high angles of attack, during entry. An assessment of design and technology implications is made.

Wurster, K. E.↗

NASA NTRS1979

Thermal protection system flight repair kit

A thermal protection system (TPS) flight repair kit required for use on a flight of the Space Transportation System is defined. A means of making TPS repairs in orbit by the crew via extravehicular activity is discussed. A cure in place ablator, a precured ablator (large area application), and packaging design (containers for mixing and dispensing) for the TPS are investigated.

Source record↗

NASA NTRS1980

Structural tests on a tile/strain isolation pad thermal protection system

The aluminum skin of the space shuttle is covered by a thermal protection system (TPS) consisting of a low density ceramic tile bonded to a matted-felt material called strain insulation pad (SIP). The structural characteristics of the TPS were studied experimentally under selected extreme load conditions. Three basic types of loads were imposed: tension, eccentrically applied tension, and combined in-plane force and transverse pressure. For some tests, transverse pressure was applied rapidly to simulate a transient shock wave passing over the tile. The failure mode for all specimens involved separation of the tile from the SIP at the silicone rubber bond interface. An eccentrically applied tension load caused the tile to separate from the SIP at loads lower than experienced at failure for pure tension loading. Moderate in-plane as well as shock loading did not cause a measurable reduction in the TPS ultimate failure strength. A strong coupling, however, was exhibited between in-plane and transverse loads and displacements.

Williams, J. G.↗

NASA NTRS1980

A design assessment of multiwall, metallic stand-off, and RSI reusable thermal protection systems including space shuttle application

The design and assessment of reusable surface insulation (RSI), metallic stand off and multiwall thermal protection systems (TPS) is discussed. Multiwall TPS is described in some detail, and analyses useful for design of multiwall are included. Results indicate that multiwall has the potential to satisfy the TPS design goals better than the other systems. The total mass of the stand-off TPS and of the metallic systems require less primary structure mass than the RSI system, since the nonbuckling skin criteria required for RSI may be removed. Continued development of multiwall TPS is required to verify its potential and to provide the necessary data base for design.

Jackson, L. R.↗

NASA NTRS1980

Photoelastic tests on models of thermal protection system for space shuttle orbiter

The thermal protection system (TPS) of the space shuttle orbiter vehicle, consisting of ceramic tile/adhesive/strain isolator pad/adhesive/aluminum substructure, was modeled photoelasticity. A highly sensitive photoelastic material was used in the models to show the nature of the stress-transfer between the strain isolation pad (SIP) and the ceramic tile through the RTV-adhesive layer. Isochromatic fringe patterns were obtained for models subjected to tension and combined tension and bending. Tests indicated that the load-transfer between the SIP and the photoelastic material occurred at discrete locations causing stress concentrations in the photoelastic material. Stress concentration factors of the order of 1.9 were measured, but as the observed photoelastic response was an integrated effect through the model thickness, the local stress concentration factors at the SIP/tile interface could be even higher.

Prabhakaran, R.↗

NASA NTRS1980

Substructure procedure for including tile flexibility in stress analysis of shuttle thermal protection system

A substructure procedure to include the flexibility of the tile in the stress analysis of the shuttle thermal protection system (TPS) is described. In this procedure, the TPS is divided into substructures of (1) the tile which is modeled by linear finite elements and (2) the SIP which is modeled as a nonlinear continuum. This procedure was applied for loading cases of uniform pressure, uniform moment, and an aerodynamic shock on various tile thicknesses. The ratios of through-the-thickness stresses in the SIP which were calculated using a flexible tile compared to using a rigid tile were found to be less than 1.05 for the cases considered.

Giles, G. L.↗

NASA NTRS1980

Mass reduction for advanced winged entry vehicles through integrated thermostructural-trajectory design

This study examines the impact of aerothermo-structure design integration on thermal protection system (TPS) mass for advanced winged entry vehicles. Four basic categories of TPS are considered: external insulation, metallic hot structures, metallic standoff, and hybrid systems. A variety of concepts that fit in these basic categories are examined. Entry trajectories tailored specifically to the characteristics of each TPS concept are generated. An aerodynamic heating program is used with the appropriately tailored trajectories to determine the centerline TPS requirements for each concept. Included in the investigation is the impact on the combined TPS-structure mass of structural materials which maintain their integrity to higher temperatures. Results indicate that significant mass reduction can be realized through appropriate aerothermo-structure design integration. An assessment is made of the relative merits of the TPS/structure/trajectory combinations considered in the study.

Wurster, K. E.↗

NASA NTRS1981

Structural tests on space shuttle thermal protection system constructed with nondensified and densified Li 900 and LI 2200 tile

Structural tests were conducted on thermal protection systems (TPS) LI 900 and LI 2200 tiles and .41 cm and .23 cm thick strain isolation pads. The bond surface of selected tiles was densified to obtain improved strength. Four basic types of experiments were conducted including tension tests, substrate mismatch (initial imperfection) tests, tension loads eccentrically applied, and pressure loads applied rapidly to the tile top surface. A small initial imperfection mismatch (2.29 m spherical radius on the substrate) did not influence significantly the ultimate failure strength. Densification of the tile bond region improved the strength of TPS constructed both of LI 900 tile and of LI 2200 tile. Pressure shock conditions studied did not significantly affect the TPS strength.

Williams, J. G.↗

NASA NTRS1981

Effect of load eccentricity and substructure deformation on ultimate strength of shuttle orbiter thermal protection system

The effect of load eccentricity and substructure deformation on the ultimate strength and stress displacement properties of the shuttle orbiter thermal protection system (TPS) was determined. The LI-900 Reusable Surface Insulation (RSI) tiles mounted on the .41 cm thick Strain Isolator Pad (SIP) were investigated. Substructure deformations reduce the ultimate strength of the SIP/tile TPS and increase the scatter in the ultimate strength data. Substructure deformations that occur unsymmetric to the tile can cause the tile to rotate when subjected to a uniform applied load. Load eccentricity reduces SIP/tile TPS ultimate strength and causes tile rotation.

Sawyer, J. W.↗

NASA NTRS1981

The Shuttle tile story

The structural problems associated with the reusable thermal protection system (TPS) of the Space Shuttle Orbiter are assessed. The ceramic insulation was placed on the aluminum in the form of about 30,000 tiles over approximately 70% of the Orbiter's exterior. The tiles were bonded to felt pads, and then the tile-pad structure was attached to the aluminum skin. As Orbiter design progressed, it was discovered that the TPS would have to withstand loads greater than initially predicted. The group tensile strength was less than that of the individual components. This was the primary factor contributing to the delay of the first flight. Values are given for Orbiter isotherms during a normal flight as well as the corresponding TPS distribution. The complete TPS assemblage is shown schematically, noting the sequence of assembling the tile components into a testing specimen. It is noted that tensile loads are applied to the strain-isolation path at discrete regions along transverse fiber bundles, causing a 50% reduction in system tensile strength. Procedures for strengthening the interface between the insulation and strain-isolation path are discussed and flight-simulation tests are outlined.

Cooper, P. A.↗

NASA NTRS1981

An assessment of the impact of transition on advanced winged entry vehicle thermal protection system mass

This study examines the impact of turbulent heating on thermal protection system (TPS) mass for advanced winged entry vehicles. Four basic systems are considered: insulative, metallic hot structures, metallic standoff, and hybrid systems. TPS sizings are performed using entry trajectories tailored specifically to the characteristics of each TPS concept under consideration. Comparisons are made between systems previously sized under the assumption of all laminar heating and those sized using a baseline estimate of transition and turbulent heating. The relative effect of different transition criteria on TPS mass requirements is also examined. Also investigated are entry trajectories tailored to alleviate turbulent heating. Results indicate the significant impact of turbulent heating on TPS mass and demonstrate the importance of both accurate transition criteria and entry trajectory tailoring.

Wurster, K. E.↗

NASA NTRS1981

Evaluation of proof testing as a means of assuring mission success for the Space Shuttle thermal protection system

The reliability analysis of a thermal protection system (TPS) incorporating low density, fibrous ceramic materials must take into account the time-dependency and variability of the system's strength. Fracture mechanics concepts can be used to estimate the allowable strength and expected lifetime, as well as to define a proof test scheme for assuring mission success of TPS. The aim of this study was to evaluate the proof testing scheme used on the TPS of the Space Shuttle with these fracture mechanics concepts. The analysis confirmed that proof testing was necessary for the undensified system and that proof testing should lead to adequate reliability with respect to the design stresses. For the undensified system, fracture mechanics predictions were confirmed by measuring the strength of samples that survived proof testing. It was also found that the time-dependent nature of the system's strength was controlled mainly by the ceramic and that this time-strength dependency is similar to that observed for bulk glasses that have compositions similar to the glass fibers present in the ceramic tiles.

Green, D. J.↗

NASA NTRS1981

A title-gap flow model for use in aerodynamic loads assessment of space shuttle thermal protection system: Parallel gap faces

The problem of predicting aerodynamic loads on the insulating tiles of the space shuttle thermal protection system (TPS) is discussed and seen to require a method for predicting pressure and mass flux in the gaps between tiles. A mathematical model of the tile-gap flow is developed, based upon a slow viscous (Stokes) flow analysis, and is verified against experimental data. The tile-gap pressure field is derived from a solution of the two-dimensional Laplace equation; the mass-flux vector is then calculated from the pressure gradient. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is given. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is given. The flow model shows tile-gap mass flux to be very sensitive to the gap width indicating a need for coupling the TPS flow and tile displacement calculation. Analytical and experimental work to improve TPS flow predictions and a possible shuttle TPS hardware modification are recommended.

Dwoyer, D. L.↗

NASA NTRS1982

An Assessment of Alternate Thermal Protection Systems for the Space Shuttle Orbiter: Executive Summary - Volume 1

Alternate thermal protection system (TPS) concepts to the Space Shuttle Orbiter were assessed. Metallic, ablator, and carbon-carbon concepts which are the result of some previous design, manufacturing and testing effort were considered. Emphasis was placed on improved TPS durability, which could potentially reduce life cycle costs and improve Orbiter operational characteristics. Integrated concept/orbiter point designs were generated and analyzed on the basis of Shuttle design environments and criteria. A merit function evaluation methodology based on mission impact, life cycle costs, and risk was developed to compare the candidate concepts and to identify the best alternate. Voids and deficiencies in the technology were identified, along with recommended activities to overcome them. Finally, programmatic plans, including ROM costs and schedules, were developed for all activities required to bring the selected alternate system up to operational readiness.

Hays, D.↗

NASA NTRS1982

Baggie: A unique solution to an orbiter icing problem

The orbiter icing problem, located in two lower surface mold line cavities, was solved. These two cavities are open during Shuttle ground operations and ascent, and are then closed after orbit insertion. If not protected, these cavities may be coated with ice, which may be detrimental to the adjacent thermal protection system (TPS) tiles if the ice breaks up during ascent, and may hinder the closing of the cavity doors if the ice does not break up. The problem of ice in these cavities was solved by the use of a passive mechanism called baggie, which is purge curtain used to enclose the cavity and is used in conjunction with gaseous nitrogen as the local purge gas. The baggie, the final solution, is unique in its simplicity, but its design and development were not. The final baggie design and its development testing are discussed. Also discussed are the baggie concepts and other solutions not used.

Walkover, L. J.↗