SEARCH · Engineering Papers

Results for “Stress test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Final Report for Closing the Loop Between In Situ Stress Complexity and EGS Fracture Complexity

Characterizing in situ stress is essential in Enhanced Geothermal System (EGS) for both risk assessment and operation design. Standard stress measurement techniques such as diagnostic fracture injection tests (DFITs) require creating hydraulic fractures and apply analytical methods such as the G -function analysis to estimate the stress. These classical approaches rely on several assumptions, including but not limited to: (i) the induced fracture is planar and persistent, and (ii) the fracture plane is normal to the minimum horizontal stress. However, these assumptions may not hold in EGS environments like Utah FORGE, where thermo-hydro-mechanical (THM) coupling, wellbore deviation, and rock heterogeneity can alter the local stress condition and consequently lead to fracture complexities in both near-well and far-field regions.

15 GEOTHERMAL ENERGY↗

DOE OSTI2021

Assessment of Overmatched Filler (Alloy 617) to Improve Alloy 800H Stress Rupture Factors

Section III, Division 5 of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) specifies rules for elevated temperature nuclear reactors. Currently, only six metals are qualified in Section III, Division for construction of Class A metallic pressure boundary components for elevated-temperature service, one of these being Alloy 800H. There are only two permissible filler metals Alloy 800H is qualified to be welded with: Alloy A and Alloy 82. The stress rupture factors for these two filler metals are low near the maximum temperatures and service lives Alloy 800H is qualified for. This may preclude vendors from being able to use Alloy 800H for elevated-temperature nuclear construction. In this work, an overmatched filler metal, Alloy 617 is assessed to determine its potential to offer improved stress rupture factors. Scoping creep-rupture tests of cross-welds with Alloy 800H base metal and Alloy 617 filler metal were conducted. Preliminary results do not indicate that Alloy 617 will offer significantly improved stress rupture factors. Consequently, a matching filler metal, UTP A 2133, is now being investigated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗

DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗

DOE OSTI2021

A Non-Invasive Approach for Elucidating the Spatial Distribution of In Situ Stress in Deep Subsurface Geologic Formations Considered for CO 2 Storage (Task 5 Report Field Scale Stress Modeling)

This report describes research accomplishments achieved with funding provided through Department of Energy (DOE) Contract DE-FE0031686, for the project “A Non-Invasive Approach for Elucidating the Spatial Distribution of In Situ Stress in Deep Subsurface Geologic Formations Considered for CO 2 Storage.” The purpose of this DOE funding is to develop non-invasive methods to obtain important information about subsurface stresses. The overall research goal of the project was to develop and improve methods for determining the spatial distribution of stresses, including magnitude and orientation of the three principal stress components in the subsurface, based on new methods that extract stress information from seismic data combined with well measurements, extended with well tests and logs, and unified in a numerical model that permits computation of the full stress tensor throughout the domains under investigation.

58 GEOSCIENCES↗

DOE OSTI2021

Development of a Vibration Technique Based on Geometric Optimization for Fatigue Life Evaluation of Sandwich Composite Structures

A major obstacle to obtaining cost-effective experimental data on the fatigue life of sandwich panels is the prohibitive amount of time and cost required to carry out millions of cycles. On the other hand, vibration techniques applied to sandwich geometries fail to match the stress patterns that are obtained from standard flexural fatigue tests. To overcome such limitations, a vibration-based fatigue technique is proposed, which entails the use of sandwich specimens whose geometries are optimized to reproduce the stress distribution observed during three point bend loading while vibrating at the first resonant frequency. The proposed vibration technique was experimentally validated. The results, compared with the average number of cycles to failure at different stress ratios obtained via the Three-Point Bending test, showed high levels of accuracy. The proposed method is robust and time effective and indicates the possibility of attaining fatigue lifetime prediction of a wide class of composite elements, such as sandwich panels.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Identification and selection of optimal reference genes for qPCR-based gene expression analysis in Fucus distichus under various abiotic stresses

Quantitative gene expression analysis is an important tool in the scientist’s belt. The identification of evenly expressed reference genes is necessary for accurate quantitative gene expression analysis, whether by traditional RT-PCR (reverse-transcription polymerase chain reaction) or by qRT-PCR (quantitative real-time PCR; qPCR). In the Stramenopiles (the major line of eukaryotes that includes brown algae) there is a noted lack of known reference genes for such studies, largely due to the absence of available molecular tools. Here we present a set of nine reference genes (Elongation Factor 1 alpha (EF1A), Elongation Factor 2 alpha (EF2A), Elongation Factor 1 beta (EF1B), 14-3-3 Protein, Ubiquitin Conjugating Enzyme (UBCE2), Glyceraldehyde-3-phosphate Dehydrogenase (GAPDH), Actin Related Protein Complex (ARP2/3), Ribosomal Protein (40s; S23), and Actin) for the brown alga Fucus distichus . These reference genes were tested on adult sporophytes across six abiotic stress conditions (desiccation, light and temperature modification, hormone addition, pollutant exposure, nutrient addition, and wounding). Suitability of these genes as reference genes was quantitatively evaluated across conditions using standard methods and the majority of the tested genes were evaluated favorably. However, we show that normalization genes should be chosen on a condition-by-condition basis. We provide a recommendation that at least two reference genes be used per experiment, a list of recommended pairs for the conditions tested here, and a procedure for identifying a suitable set for an experimenter’s unique design. With the recent expansion of interest in brown algal biology and accompanied molecular tools development, the variety of experimental conditions tested here makes this study a valuable resource for future work in basic biology and understanding stress responses in the brown algal lineage.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

High-burnup fuel stress analysis prior to and during a LOCA transient

High-burnup fuel fragmentation and pulverization have been experimentally observed during simulated loss-of-coolant accident (LOCA) transient testing of high-burnup (>62 GWd/tU) nuclear fuel. The cause of this phenomenon is generally accepted to be the formation of stresses arising from the off-normal conditions. However, the primary mechanism(s) contributing to the stress formation is/are still being debated. Leading hypotheses suggest that the concurrence of fission gas bubbles and high burnup structure on the pellet periphery (i.e., the rim) leave the fuel susceptible to pulverization. Other hypotheses suggest that pulverization is artificially inflated during externally heated tests that do not reproduce prototypic fuel stresses and radial temperature profiles as the fuel transitions from full-power nuclear heating to decay heating. This work performs finite element analyses of fuel pellet temperatures and macroscopic stresses prior to and during a LOCA transient to identify (1) operating conditions that may exacerbate the fuel pellet stress state, (2) differences in predicted stresses with nuclear vs. furnace heating, and (3) how fuel cracking impacts the subsequent stress state in the pellet fragments. Analyses predict that macroscopic transient fuel stresses resulting from constrained thermal expansion will remain below the fracture stress of fresh UO 2 once the fragment size reaches ~4 mm or less. Calculated fuel stresses from simulated LOCA tests performed with representative nuclear vs. electrical heating rates are shown to be equal within 5% and essentially unchanged for all times after the first 27 seconds of the transients. Because the fuel stresses do not change once the temperature profile becomes uniform, macroscopic transient stresses would be no different than those following a normal shutdown. Because pulverization of high burnup fuel does not occur prior to a LOCA test, pulverization of high burnup UO 2 cannot be initiated by differential thermal stresses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Data Management for Digital Twin Implementation: Enhancing Existing SCADA Architecture for INL's CITRC Test Distribution System

The United States power grid will continue to experience stress from aging infrastructure, extreme weather, and increasing loads. In order to strengthen resiliency, researchers need to run tests and simulations that model real-life infrastructure. Idaho National Laboratory (INL) is creating a digital twin of its Critical Infrastructure Test Range Complex (CITRC). CITRC is an at-scale grid testbed which can be configured in utility-realistic distribution scenarios for a variety of tests, such as advanced grid protection and control. A digital twin of this infrastructure would support in-depth tests/simulations without risking physical consequences, before trialing devices under test at-scale. This project focuses on the data acquisition part of constructing a digital twin. It investigates the Supervisory Data Acquisition and Control (SCADA) system of CITRC and explores ways to utilize this system for the twin. Future “ideal” at-scale implementations such as upgraded equipment, modern communication protocols, and automation applications are also explored.

24 - POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

A thermodynamically consistent finite strain phase field approach to ductile fracture considering multi-axial stress states

Phase field models for ductile fracture have gained significant attention in the last two decades due to their ability in implicitly tracking the nucleation and propagation of cracks. However, most crack phase field formulations for elastoplastic solids focus only on the effects of plastic deformation, and do not consider the different multi-axial stress states that may arise in practical designs. In this work, a thermodynamically consistent phase field approach coupled with finite strain plasticity, considering multi-axial stress states is presented. In order to account for the coupling between plasticity and stress states, the Stress-Weighted Ductile Fracture Model (SWDFM) is utilized. The SWDFM represents a criterion for predicting ductile crack initiation under both monotonic and cyclic loadings based on histories of an internal plastic variable, stress triaxiality, and the Lode angle parameter. The excellent performance of the SWDFM for predicting ductile crack initiation motivates for its incorporation into a phase field approach for predicting both crack initiation and propagation through degradation of the fracture toughness. Moreover, based on the second law of thermodynamics, exact requirements are imposed on the rate at which the fracture toughness can evolve. Here, a novel function for degrading the plastic yield surface during the evolution of damage is introduced. This function, in line with experimental observations, leads to an accumulation of plastic deformation in damaged regions of a solid, and avoids numerical instabilities arising from concentrations of large plastic deformations in severely damaged regions. For validating the proposed model, results of computational simulations are compared to data from selected tests considering different multi-axial stress states. Comparisons of the numerical results with data from laboratory experiments demonstrate the capabilities of the proposed framework.

42 ENGINEERING↗

DOE OSTI2020

Mechanical testing of PH13-8Mo H950 Steel for Xue-Wierzbicki Fracture Criterion Determination at 20° C and -40° C

Mechanical testing was conducted to collect the data needed to build a Xue-Wierzbicki (XW) fracture model for PH13-8 Mo H950 stainless steel (PH 13-8 SS). This model is intended for use in structural analysis of this material between room temperature and -40° C. Tests were performed on four different specimen geometries such that a range of stress states were characterized at room temperature and -40° C. Tensile tests on R5 tensile specimens were also performed to assess material anisotropy. Fracture toughness test were also conducted. The fracture toughness of this material at -40° C was 68% of the room-temperature value. Material strength generally increased with decreasing temperature while the opposite trend was observed for ductility. These trends were most pronounced for specimens with the largest stress triaxialities.

36 MATERIALS SCIENCE↗

DOE OSTI2024

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Magnetic and Mechanical Analysis of a Large Aperture 15 T Cable Test Facility Dipole Magnet

The US Department of Energy (DOE) Office of Science (SC), is funding a large bore “Cable Test Facility Magnet” for testing advanced cables and inserts in high transverse field. This is a joint effort between the Office of High Energy Physics (HEP) and the Office of Fusion Energy Sciences (FES). The background field magnet for this facility is being developed at Lawrence Berkeley National Laboratory (LBNL) while the cryostat and test facility will be located and operated by Fermi National Accelerator Laboratory (FNAL). The Nb 3 Sn dipole magnet, which will provide the transverse background field, is designed to generate a field of 15 T in a 100 × 150 mm bore at 1.9 K. The conceptual design of a block-type dipole with flared ends and a structure based on key-and-bladder technology will be introduced. The results of the magnetic and mechanical analysis will be presented.

43 PARTICLE ACCELERATORS↗

DOE OSTI2020

Calibration of CDM-Based Creep Constitutive Model Using Accelerated Creep Test (ACT) Data

In conventional creep testing (CCT) a specimen is subject to constant load and temperature for a long-duration until creep rupture occurs. Conventional testing can be costly when considering the number of experiments needed to characterize the creep response of a material over a range of stress and temperature. To predict long-term creep-rupture properties, the time-temperature-stress superposition principle (TTSSP) approach has been employed where stress and/or temperature is applied at an elevated level; the result of which are extrapolated down to low stress and/or temperature conditions. These methods have been successful in predicting minimum-creep-strain-rate (MCSR) and stress-rupture (SR) but suffer from an inability to predict the creep deformation curve or account for changes in deformation mechanisms or aging that occurs at long-duration. An accelerated technique, termed the Stepped isostress method (SSM) allows the accelerated testing of materials to determine their creep deformation response. Unlike TTSSP tests, the SSM test employs a single specimen where the stress is periodically step increased until rupture. The SSM creep deformation curve is processed (time and strain shifted) to produce an accelerated creep deformation curve that represent the creep deformation curve at the initial stress level in SSM. A processing procedure for metals has yet to be developed. The research objective of this study is to develop a processing procedure for SSM test data using a creep-damage constitutive model. Triplicate SSM tests were conducted on Ni-based superalloy Inconel 718 at 650°C with stress being periodically increased until rupture. Triplicate CCT tests were conducted at the initial stress level of the SSM tests. The Sine-hyperbolic (Sinh) creep-damage model was employed in this study. The Sinh creep-damage constitutive model is based on coupled creep strain rate and damage evolution equations; where both rates are dependent on the current state of damage. Calibration is two-step: analytical and numerical optimization. Each stepped creep deformation curve is tackled quasi-analytically to determine MCSR and SR related material constants and accumulated damage. The damage accumulated at the end of each step was then passed onto subsequent steps to calibrate the MCSR, rupture prediction, and damage evolution. Numerical optimization was applied to optimize model constants involved in the creep strain constitutive equations in order to generate best-fitted Sinh creep deformation curves. The Sinh model predictions were compared to the SSM and CCT data. The Sinh model satisfactorily predicts the SSM data and thus the calibrated material constants provides a good estimate of rupture found in the CCT data. Calibration using SSM data reduces the number of tests needed to calibrate a model; significantly reducing costs. A single SSM test replaces numerous creep tests at different stresses.

36 MATERIALS SCIENCE↗

DOE OSTI2024

The human plasma lipidome response to exertional heat tolerance testing

The year of 2023 displayed the highest average global temperatures recorded in history— the duration and severity of extreme heat are projected to increase. Rising global temperatures represent a major public health threat, especially to occupations exposed to hot environments, such as construction and agricultural workers, and first responders. Despite efforts of the scientific community, there is still a need to characterize the pathophysiological processes leading to heat related illness and develop biomarkers that can predict its onset. Here, we performed a plasma lipidomic analysis on male and female subjects who underwent heat tolerance testing (HTT), consisting of a 2-h treadmill walk at 5 km/h with 2% inclination at a controlled temperature of 40oC. We identified 995 lipids from 27 classes, with nearly half of all detected lipids being responsive to HTT. Lipid classes related to substrate utilization were predominantly affected by HTT, with a downregulation of triacylglycerols and upregulation of free fatty acids and acyl-carnitines. We additionally examined correlations between changes in plasma lipids by using the even chain acyl-carnitines is physiological strain index (PSI). Here, even chain acyl-carnitines, bi-products of incomplete beta oxidation, and diacylglycerols displayed the highest correlation to PSI. PSI did not correlate with plasma lactate levels, which suggests that correlations with related to metabolic efficiency versus physical exertion. Overall, our results show that HTT has a strong impact on the plasma lipidome and that incomplete beta oxidation may underlie heat intolerance.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2024

Rheology characterization of ionic liquids under high pressure and high temperature

Ionic liquids (ILs) are liquid salts that exist at or below ambient temperatures and are composed of ion pairs. They offer promising alternatives to toxic, hazardous, highly flammable, and volatile solvents in various applications such as solution preparation, dispersion, gel formation, composites, and polymer melts. ILs possess unique and interesting characteristics, including excellent chemical and thermal stability and low vapor pressures. Understanding the rheological properties of ILs is essential to optimizing IL performance. This paper presents a comparative analysis of the rheological properties of two ionic liquids, Nsingle bondHexylpyridinium tetrafluoroborate (HPyBF4) and Nsingle bondHexylpyridinium bromide (HPyBr), under different shear rates, temperatures, and pressures. Rheological measurements were performed under varying controlled pressure and temperature conditions. The experimental investigation covered a pressure range of 689–12,411 kPa [100–1800 psi] and a temperature range from room temperature up to 522 kelvin (K) [480°F]. The primary objective is to explore and compare the flow behavior and viscoelastic characteristics of HPyBF4 and HPyBr under high-pressure and high-temperature conditions. The experimental data showed that HPyBF4 and HPyBr exhibited shear-thinning behavior, and pressure had an insignificant effect on rheology compared to the temperature effect. Under the same testing conditions, HPyBr showed higher shear stress and viscosity than HPyBF4. This research significantly contributes to the improved understanding of the rheological behavior of these specific ionic liquids and their suitability for diverse industrial and scientific applications, particularly in high-pressure and high-temperature environments.

15 GEOTHERMAL ENERGY↗

DOE OSTI2025

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗