Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Source release”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Light-absorbing impurities accelerating glacial melting in southeastern Tibetan Plateau

Deposition of light-absorbing particles on glacier surfaces poses a series of adverse impacts on the cryospheric environment, climate and human health. Broad attention of the scientific community has been paid on insoluble light-absorbing impurities (ILAIs) in snow and ice on glaciers over the Tibetan Plateau (TP). However, systematic investigation of ILAIs in snowpack of glaciers on the TP is scarce. In this study, the properties and darkening effect of ILAIs in snowpack on glaciers are extensively investigated in the southeast of TP. Results show that ILAIs concentrations in multiple types of snow and ice samples were significantly different. Snowpit depths varied substantially from one profile to another during May and June 2016. The average concentrations of ILAIs in snowpits increase as snow melting progresses. Black carbon (BC) and dust cause snow albedo reduction more in snow with larger grain size Re. Based on a radiative transfer model calculation, the average albedo reduction induced by BC in the snowpack was 0.141 ± 0.02, and associated daily maximum radiative forcing (RF) was 72.97 ± 12.7 W m-2. BC is a controlling light-absorbing factor in snowpack and causes substantial albedo reduction and thus the associated daily maximum RF. The maximum reduction of snow cover duration was 4.56 ± 0.71 days caused by BC and dust in snowpack in southeastern TP. The average mass absorption cross-section (MAC) of BC from multiple snowpits was 3.26 ± 0.46 m2 g-1, which represents a typical value of MAC in snow on glaciers, but it is type-dependent of snow/ice samples. Tropospheric aerosols vertically extended up to 8 km over the TP and its surrounding areas, which indicates the transport of aerosols from remote sources through elevated pathways. A large amount of carbon stored in the brittle glaciers can be potentially released with meltwater runoff under a warming climate. This study provides a new insight for investigating carbonaceous and light-absorbing particles in glacierization areas.

Niu, Hewen↗
DOE OSTI2024

What if GW190425 did not produce a black hole promptly?

ABSTRACT It is widely believed that the binary neutron star merger GW190425 produced a black hole promptly upon merger. Motivated by the potential association with the fast radio burst FRB 20190425A, which took place 2.5 h after the merger, we revisit the question of the outcome of GW190425 by means of numerical relativity simulations. We show that current laboratory and astrophysical constraints on the equation of state of dense matter do not rule out the formation of a long-lived remnant. However, the formation of a stable remnant would have produced a bright kilonova, in tension with upper limits by ZTF at the location and time of FRB 20190425A. Moreover, the ejecta would have been optically thick to radio emission for days to months, preventing a putative FRB from propagating out. The predicted dispersion measure is also several orders of magnitude larger than that observed for FRB 20190425A. Our results indicate that FRB 20190425A and GW190425 are not associated. However, we cannot completely rule out the formation of a long-lived remnant, due to the incomplete coverage of the relevant sky regions. More observations of GW190425-like events, including potential upper limit, have the potential to constrain nuclear physics. To this aim, it is important that follow-up observational campaigns of gravitational wave events are informed by the properties of the source, such as their chirp mass, and we urge the LIGO-Virgo-KAGRA collaboration to promptly release them publicly.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

New Developments and Capabilities Within WEC-Sim

WEC-Sim is an open-source software for simulating wave energy converters and has been actively developed and applied since its initial release in 2014 to simulate a wide variety of device archetypes. WEC-Sim is developed jointly by the National Renewable Energy Laboratory and Sandia National Laboratories within the MATLAB/SIMULINK environment. A general wave-to-wire model begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of wave energy converters (WEC), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modeling the entire wave-to-wire is difficult and encompasses multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze, and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM)-based frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). With this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Additional WEC-Sim functionalities include pre-built Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems. The developers of WEC-Sim continue to release new versions of the software, at least annually, with the latest release in September 2022. These releases include bug fixes, updates to software documentation, as well as new features to expand WEC-Sim's capabilities to model a wide range of WEC concepts. This publication will highlight the new features added to WEC-Sim between versions 4.1.0 to 5.0.1, which spans a 2-year period from June 2020 to September 2022. New features described here include topics such as continuous integration checks, revised Morison Element and nonlinear hydro implementations, run directly from Simulink (required for hardware-in-the-loop execution), BEMIO updates to import Capytaine BEM hydrodynamics, addition of cable blocks, and new wave visualization features.

TIDAL AND WAVE POWER↗
DOE OSTI2020

beluga

Submission-beluga is an open-source optimal control software that uses publicly available indirect methods to model inequality constraints at boundaries. This release of beluga introduces a method known as UTM, modified handling of constraints to support the UTM method, and includes bug fixes and related requirements changes.SAND2020-12847 M Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

Sparapany, Michael↗
DOE OSTI2021

A Verification of Flux Sensitivity Estimates Using the MCNP Tally Perturbation Tool

Nuclear data is commonly used in applications such as nuclear nonproliferation, safeguards, and criticality safety. More specifically, nuclear data is used in predictive simulation codes like the Monte-Carlo N-Particle (MCNP ® ) transport code, Serpent, and similar radiation transport codes. The improvement of nuclear data enables more precise and accurate simulations, which result in higher fidelity designs and reduced operational/procedural costs. Therefore, the improvement of nuclear data is of paramount importance across the nuclear community. Nuclear data is improved and validated through integral benchmark experiments. The design of benchmark experiments is an extensive process; therefore, these experiments are often optimized on multiple characteristics, including sensitivity to the nuclear data, during the design process. Sensitivity is a measure of how much a quantity changes due to changes in independent variables such as experimental configuration. An experimental design that has a larger sensitivity to the nuclear data of interest will have a larger impact on the accuracy and precision of the validated data. Past integral benchmark experiments have primarily used the effective multiplication factor ($k_{eff}$) as the predominant measured quantity; however, experiments designed with other quantities in mind would be able to optimize on validating different areas of the nuclear data. A primary goal of the EUCLID project is to design, constrain, and reduce compensating errors in experiments focused on quantities other than $k_{eff}$ to better validate nuclear data across the board. Currently, there is a capability in MCNP to easily calculate the sensitivity of $k_{eff}$ to specific nuclear data of numerous reactions types and isotopes (KSEN card); however, the sensitivity of other quantities must be estimated in more strenuous manners. For example, the perturbation feature (PERT card) of MCNP can be used to estimate first-order sensitivities of some response in fixed source simulations. A recent announcement revealed that the first- and second-order perturbation features in previous releases of MCNP contained a bug. It was identified that particles were being scored into the wrong energy bin. The bug is in the most recent public release (MCNP6.2); however, a patch has been added to the most up to date version (MCNP6.2.2) that has not been released publicly. A direct comparison of the PERT card results for an F4 (neutron flux averaged over a cell) tally before and after the patch are shown in figure 1. All simulations used in the sensitivity estimates in this report were performed with MCNP6.2.2. This work verifies the patched MCNP perturbation tool by comparing first order sensitivities made using the PERT card to estimates made using manual perturbation of the compact ENDF (ACE) files.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Thermochemical Modeling in Molten Fluoride Salts for Radionuclide Speciation

An important aspect of the licensing process for nuclear reactors is providing a reasonable assurance of safety to the general public. This includes modeling potential radionuclide releases from the reactor during normal operations and accident scenarios, which is known as the reactor’s source term. A new class of advanced (non-LWR) reactors are being developed which use molten salts as the coolant fluid. Because the molten salt coolant represents a credited barrier for radionuclide transport between the fuel and the environment, a necessary aspect of mechanistic source term (MST) analysis for the KP-FHR is modeling the thermochemistry of molten salts. Provided here is a review of the theory of the thermodynamic principles governing multicomponent phase equilibria, the background of molten salt thermochemistry research, and a summary of the thermochemical data relevant to the KP-FHR coolant salt, Li 2 BeF 4 , commonly referred to as “FLiBe”. A review of literature is followed by a brief introduction to methods that can be used to model the thermochemical behavior of molten salt mixtures. The methodology outlined is based on the use of a commercial thermodynamic modeling software called FactSage, which is one of only a few available softwares based on the modified quasichemical model(MQM), which is the recommended solution model for molten salts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

ACES: Infrastructure As Code. Model Optimization and Performance Capability

Infrastructure as Code (IaC) refers to managing infrastructure (networks, physical/virtual machines, storage, and connection topology) in a descriptive model/language, rather than configuring it manually or using interactive configuration tools. Just like source code can be compiled to generate the same binary code, IaC enables generating the same environment every time it is applied. IaC is a key DevOps practice and is generally used in conjunction with continuous integration (CI) and continuous delivery (CD). In CI, all code changes are merged into a mainline branch and validated multiple times a day as developers check in their changes to the source code. In CD on the other hand, code changes are automatically packaged for a new release-to-production on a regular basis. This typically enables teams to deliver software changes much more quickly and often. Developing and managing the ACES platform using (IaC) is vital for the robust deployment and continued sustainment of this foundational computing capability. IaC and DevOps practices will help us solve many of the common challenges often encountered in developing and maintaining compute infrastructure. First, it will make the provisioning, deployment, and maintenance of the compute infrastructure across multiple environments much more efficient. Second, these processes help make the overall system much more stable by continuously testing new changes as they are introduced to the system. Third, it allows us to be much more confident of the security controls in place since they can be tested as part of the CI process and all new changes can be audited and tracked. Finally, IaC enables the ACES Platform to be adaptable to the emerging technologies due to its ability to spin up different test beds to evaluate and incorporate these technologies. This document addresses common infrastructure-management challenges, describes what happens if they are not addressed, and highlights the value of utilizing IaC to tackle them. Finally, we will provide a high-level overview of the IaC and DevOps practices being utilized by the ACES Platform team.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

H2@Scale Concept Hydrogen Demand and Resources

The H2@Scale concept involves hydrogen as an energy intermediate. Hydrogen can be produced from various conventional and renewable energy sources including as a responsive load on the electric grid. Hydrogen has many current applications and many more potential applications, such as energy for transportation, as a feedstock for synthetic fuels, and to upgrade oil and biomass, heat for industry and buildings, and electricity storage. Owing to its flexibility and fungibility, a hydrogen intermediate could link energy sources that have surplus availability to markets that require energy or chemical feedstocks, benefiting both. This data release provides estimates on hydrogens serviceable consumption potential for possible hydrogen applications and the technical potential for producing hydrogen from various resources. We define the technical potential as the resource potential constrained by real-world geography and system performance, but not by economics.

Array↗
DOE OSTI2024

BSEC VPRM 10m Hourly Biogenic Fluxes in Baltimore (2021)

Model outputs from the Vegetation Photosynthesis and Respiration Model (VPRM: version from Horne et al. in prep). Model remote sensing inputs come from Sential 2-derived EVI and LSWI. Model meteorological inputs for two-meter air temperature and shortwave incoming come from the BSEC WRF 2021 Control Run (Foust, W. 2023). Plant functional Types (PFTs) are spatially classified using the Chesapeake Bay Program 2018 land use land cover product. The final biogenic flux (µmol CO2 m^-2 s^-1) outputs of NEE, RESP, and GEE are a weighted average based on the portion of PFTs within the cell. Individual PFT outputs are saved inside PFT directories (e.g., Crops, Grass, etc.) inside the specific month directory. Model outputs are denoted as a negative flux into the land system (i.e., photosynthesis) and a positive flux as a net release into the overlying atmosphere. Respiration (RESP) fluxes are positive and combine heterotrophic (only soil) and autotrophic sources. Gross ecosystem exchange (GEE) is a negative flux driven by only photosynthetic activity from vegetation, and the Net ecosystem exchange (NEE) is the sum of the two (i.e., NEE=RESP+GEE). Data Characteristics Spatial Resolution: 10m Temporal Resolution: Hourly File Format: VPRM_ _BSEC. .tif (Hour is in UTC) For more information on the model results, please email Jason Horne (jph6488@psu.edu). References: Foust, W. (2023). BSEC WRF 2021 Control Run Output (v0.1.0) [Data set]. MSD-LIVE Data Repository. https://data.msdlive.org/records/m0e6m-vvq17

Baltimore↗
DOE OSTI2023

New Developments and Capabilities Within WEC-Sim: Preprint

WEC-Sim is an open-source software for simulating wave energy converters, which has been actively developed and applied since its initial release in 2014 to simulate a wide variety of device archetypes. WEC-Sim is developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (Sandia) within the MATLAB/SIMULINK environment. A general wave-to-wire model begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of wave energy converters (WEC), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modeling the entire wave-to-wire is difficult and encompasses multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze, and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM)-based frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). With this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Additional WEC-Sim functionalities include pre-built Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems. The developers of WEC-Sim continue to release new versions of the software, at least annually, with our latest release in September 2022. These releases include bug fixes, updates to software documentation, as well as new features to expand WEC-Sim's capabilities to model a wide range of WEC concepts. This publication will highlight the new features added to WEC-Sim between versions 4.1.0 to 5.0.1 which spans over a two year period from June 2020 to September 2022. New features to be described will include topics such as continuous integration checks, revised Morison Element and nonlinear hydro implementations, run directly from Simulink (required for hardware-in-the-loop execution), BEMIO updates to import Capytaine BEM hydrodynamics, addition of cable blocks, and new wave visualization features.

TIDAL AND WAVE POWER↗
DOE OSTI2024

ComStock™ 2024 Release 1 [SWR-19-33 and SWR-20-32]

ComStock™ is an NREL model of the U.S. commercial building stock. The model takes some building characteristics from the U.S. Department of Energy's (DOE's) Commercial Prototype Building Models and Commercial Reference Building. However, unlike many other building stock models, ComStock also combines these with a variety of additional public- and private-sector data sets. Collectively, this information provides high-fidelity building stock representation with a realistic diversity of building characteristics. This repository contains the source code used to build and execute ComStock models, including upgrade scenarios. In addition, the sampling of buildings characteristics used for the initial ComStock (V1.0) release is provided. The ComStock model is under active calibration and development, which is publicly visible on this repository. Execution of the ComStock workflow is managed through the buildstockbatch repository, a shared asset of ResStock™ and ComStock™ , specifically developed to scale to execution of tens of millions of simulations through multiple infrastructure providers. The dataset output from the initial ComStock (V1.0) release can be found at the accompanying ComStock data viewer website and additional information about ComStock found on the NREL Buildings Website. For more details about ongoing model development please consult the End Use Load Profiles website. ComStock is a direct result of the NREL residential stock modeling tool ResStock™ (recipient of a R&D100 award) and was inspired by the high-fidelity solar & storage adoption model dGen™. Additionally, this tool would not be possible without the decades of work undertaken by the OpenStudio® and EnergyPlus® visionaries and contributors, significant funding, feedback and support from the Los Angeles Department of Water and Power, and the Department of Energy's Building Technology Office ongoing support of and investment in building energy modeling software. is an analytic methodology for modeling the energy usage of the commercial building stock within the United States of America. The commercial building stock is represented through a sampling of complex probabilistic distributions of various features of interest for modeling energy usage within commercial buildings. Each sample from these distributions is converted into a building energy model based on the features of that specific sample. Each building energy model can be simulated as is, but additional changes can be made to the model through addition of energy conservation measures, component faults, or other desired alterations. The results of the simulations are then processed to provide insights for various stakeholders, including but not limited to policy makers, engineers, and marketers.

Horsey, Henry↗
DOE OSTI2022

Wintertime Brine Discharge at the Surface of a Cold Polar Glacier and the Unexpected Absence of Associated Seismicity

A subglacial groundwater system beneath Taylor Glacier, Antarctica, discharges hypersaline, iron-rich brine episodically at the glacier surface to create Blood Falls. However, the triggering mechanism for these brine release events is not yet understood. Identifying which fracture processes are observed seismically can help us better characterize the hydrological system at Taylor Glacier, and more generally, provide us with a broader understanding of englacial hydrologic activity in cold glaciers. We document wintertime brine discharge using time-lapse photography. Subfreezing air temperatures during the brine discharge indicate that surface melt-induced hydrofracture is an unlikely trigger for brine release. Further, we analyze local seismic data to test a hypothesis that fracturing generates elevated surface wave energy preceding and/or coinciding with brine release events. Our results show no discernible elevated Rayleigh wave activity prior to or during Blood Falls brine release. Instead, we find a pattern of seismic events dominated by a seasonal signal, with more Rayleigh events occurring in the summer than the winter from the Blood Falls source area. We calculate that the volumetric opening of cracks that would generate Rayleigh waves at our detection limits are of similar size to myriad cracks in glacier ice, lake ice, and frozen sediment in the terminus area. We therefore propose that any fracturing coincident with brine release activity likely consists of a series of smaller opening events that are masked by other seismicity in the local environment.

58 GEOSCIENCES↗
DOE OSTI2020

Advances in Resin Management Using 3R-Scan - 20154

The most important factor underlying optimal waste management is developing a clear picture of the radioactivity content of the waste and its impact on waste disposal cost. For over 35 years since the publishing of 10CFR61, waste characterization has relied on sampling the final waste product after formation. In the days following 10CFR61, the cost of final disposal was marginal with only a small impact on the overall costs. Constraints were added by provisions of the Low Level Waste Policy Act of 1985 leading to increasingly limited access to those disposal sites that remained available. In addition, Nuclear Regulatory Commission (NRC) pressure promoting waste volume reduction led to disposal costs inevitably rising. Despite this, characterization practices in monitoring of waste generation for activity content still center on the same dated processes. This results in a disposal classification on the basis of endpoint sampling without consideration of the homogeneity of the waste mixture. It can also disregard consideration of the representativeness of the single or small sample base. As a minimum effort, a formalized sampling program of a fixed grouping of waste streams can be implemented that could account for more than 95% of all of the activity carried in solid waste products. The sample results for each radionuclide could then be trended as time passes to develop reasonable scaling factors for difficult to measure radionuclides. This process, identified in NRC guidance, has been rigorously followed by a relatively small number of facilities. The trended scaling factors serve to improve accuracy by identifying anomalous results that could otherwise go undetected. Direct monitoring of the accumulation of activity in process streams generating solid radwaste, including demineralizers and filter streams, is a more precise approach. Nearly all of these streams are monitored by plant chemistry on a regular schedule to maintain water quality. This paper discusses viable options for developing the basis for characterization through process monitoring of the accumulation of activity at the point of generation. Special focus is on resin bed tracking and how process knowledge of these streams can be brought together to form a consistent and precise solid waste radioactivity inventory. Some of the specific points covered in this paper include the merger of the fission product release computer program, 3R-STAT, with the radwaste sample analysis computer program, SCAN4 to create 3R-SCAN, the importance of individual waste stream influences on the overall source term, and the use of historic sample data to develop scaling factors using an automated process. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

The Fourth Catalog of Active Galactic Nuclei Detected by the Fermi Large Area Telescope: Data Release 3

Abstract An incremental version of the fourth catalog of active galactic nuclei (AGNs) detected by the Fermi Large Area Telescope is presented. This version (4LAC-DR3) derives from the third data release of the 4FGL catalog based on 12 yr of E > 50 MeV gamma-ray data, where the spectral parameters, spectral energy distributions (SEDs), yearly light curves, and associations have been updated for all sources. The new reported AGNs include 587 blazar candidates and four radio galaxies. We describe the properties of the new sample and outline changes affecting the previously published one. We also introduce two new parameters in this release, namely the peak energy of the SED high-energy component and the corresponding flux. These parameters allow an assessment of the Compton dominance, the ratio of the inverse-Compton to the synchrotron-peak luminosities, without relying on X-ray data.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Evidence for suprathermal ion distribution in burning plasmas

At the National Ignition Facility, inertial confinement fusion experiments aim to burn and ignite a hydrogen plasma to generate a net source of energy through the fusion of deuterium and tritium ions. The energy deposited by α-particles released from the deuterium–tritium fusion reaction plays the central role in heating the fuel to achieve a sustained thermonuclear burn. In the hydrodynamic picture, α-heating increases the temperature of the plasma, leading to increased reactivity because the mean ion kinetic energy increases. Therefore, the ion temperature is related to the mean ion kinetic energy. In this report we use the moments of the neutron spectrum to study the relationship between the ion temperature (measured by the variance in the neutron kinetic energy spectrum) and the ion mean kinetic energy (measured by the shift in the mean neutron energy). We observe a departure from the relationship expected for plasmas where the ion relative kinetic energy distribution is Maxwell–Boltzmann, when the plasma begins to burn. Understanding the cause of this departure from hydrodynamic behaviour could be important for achieving robust and reproducible ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Improved Verification and Validation Testing and Tools [Slides]

All MCNP team supported V&V test suites are now developed in a separate repository from the MCNP source code within a Python-based framework. This entire framework will be distributed with the upcoming MCNP6.3 release. Most V&V test suites distributed with MCNP6.2 will be distributed in new framework. New V&V test suites are done or being worked on for the MCNP6.3 release.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Riverine Plastic Pollution: Field Sampling Protocol and Implementation in U.S. Rivers

Riverine plastic pollution is increasingly being recognized as a serious environmental concern. The flux of plastic from U.S. rivers into the oceans is estimated to be on the order of hundreds of tons per year. Plastic pollution has been detected in all major U.S. rivers but the observations did not measure metrics that could be used for mass flux calculations. The Department of Energy is addressing the problem of riverine plastic pollution with the Waterborne Plastics Resource Assessment and Debris Characterization (WaterPACT) project. Phase one of the WaterPACT project includes the development of a sampling protocol, field sampling events that implement the protocol, and numerical modeling studies. The field sampling will quantify and characterize the plastic pollution and the numerical modeling studies will analyze the movement of the plastic pollution by rivers. This report details the WaterPACT sampling protocol and its implementation in four major U.S. rivers. The WaterPACT sampling protocol was implemented in the Mississippi, Columbia, Delaware, and Los Angeles rivers with at least three sampling events in each river. The rivers represent four types ranging from the large Mississippi with its vast agricultural watershed to the small Los Angeles with its highly engineered urban waterway. The three sampling events covered a variety of discharge conditions from low drought flow to extreme storm events. The data obtained by the WaterPACT sampling of the four rivers will be combined to provide an invaluable dataset to researchers studying the source and chemical composition of plastic pollution and modelers estimating the flux of plastic being transported to and released into the oceans.

13 HYDRO ENERGY↗
DOE OSTI2025

Transition of SRT Source Term Software to Modern Version Control System to Enable More Efficient Verification, Validation, and User Engagement

The Simplified Radionuclide Transport (SRT) code assists in reactor design and licensing by providing a detailed analysis of radionuclide transport under specific transient scenarios. This analysis is essential for ensuring that reactors meet safety and regulatory standards before they are authorized to operate. Mechanistic source term analysis, which involves a realistic evaluation of radionuclide behavior from the source to the environment, is a key component of this process. It provides a comprehensive understanding of potential release scenarios, supporting the development of robust safety measures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗