SEARCH · Engineering Papers

Results for “STRENGTH CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strengths showed an unexpected interaction involving the bearing mode. Compressive bypass loads reduced the bearing strength by decreasing the bolt-hole contact arc and thus increasing the severity of the bearing loads. The bearing stresses at the hole boundary were not accurately estimated by superposition of the stress components for separate bearing and bypass loading. However, superposition produced reasonably accurate estimates for tangential stresses especially near the specimen net-section.

Crews, J. H., Jr.↗

NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

Crews, J. H., Jr.↗

NASA NTRS1987

Effect of atmospheric turbulence on the bit error probability of a space to ground near infrared laser communications link using binary pulse position modulation and an avalanche photodiode detector

The effect of atmospheric turbulence on the bit error rate of a space-to-ground near infrared laser communications link is investigated, for a link using binary pulse position modulation and an avalanche photodiode detector. Formulas are presented for the mean and variance of the bit error rate as a function of signal strength. Because these formulas require numerical integration, they are of limited practical use. Approximate formulas are derived which are easy to compute and sufficiently accurate for system feasibility studies, as shown by numerical comparison with the exact formulas. A very simple formula is derived for the bit error rate as a function of signal strength, which requires only the evaluation of an error function. It is shown by numerical calculations that, for realistic values of the system parameters, the increase in the bit error rate due to turbulence does not exceed about thirty percent for signal strengths of four hundred photons per bit or less. The increase in signal strength required to maintain an error rate of one in 10 million is about one or two tenths of a db.

Safren, H. G.↗

NASA NTRS1978

Bar-driven spiral waves in disk galaxies

The response of rotating disks of gas to barlike perturbations in galactic gravitational fields is investigated. In particular, two-dimensional time-dependent numerical hydrodynamical calculations have been performed in order to determine the steady-state response of disks of gas to rotating barlike perturbations. Two types of barlike perturbations are considered: oval distortions in the axisymmetric gravitational field of the disk, and heterogeneous prolate spheroids. The calculations reveal that in the absence of gaseous self-gravity, a viscous differentially rotating disk of gas responds to a rotating barlike perturbation by forming a central gas bar with two trailing spiral waves. The local phase of the gas response is primarily a function of the number and spacing of the principal resonances in the disk. This result may be understood in terms of particle orbit theory. The gas response to barlike perturbations also depends on the relative strength and the effective axial ratio of the bar. In these calculations strong narrow bars produce offset shocks in the central gas bar. These shocks correspond in position to the long narrow dust lanes observed in many barred spiral galaxies.

Huntley, J. M.↗

NASA NTRS1972

Interpolation constants for calculation of transmittance and rate of dissociation of molecular oxygen in the mesosphere and lower thermosphere

Values of band oscillator strengths and rotational line widths for the Schumann-Runge band system have been used to derive interpolation constants from which the transmittance and rate of dissociation of molecular oxygen can be calculated. These constants, valid for temperatures between 150 and 300 K and for column densities between 1 x 10 to the 17th power/cm sq and 7 x 10 to the 24th power/cm sq, cover the wavelength range 1750 and 2050A.

Hudson, R. D.↗

NASA NTRS1952

A Summary of Diagonal Tension Part I : Methods of Analysis

Previously published methods for stress and strength analysis of plane and curved shear webs working in diagonal tension are presented as a unified method. The treatment is sufficiently comprehensive and detailed to make the paper self-contained. Part 1 discusses the theory and methods for calculating the stresses and shear deflections of web systems as well as the strengths of the web, the stiffeners, and the riveting. Part 2, published separately, presents the experimental evidence. (author)

Kuhn, Paul↗

NASA NTRS1947

Strength analysis of stiffened beam webs

Explore the source record for details and available documents.

STRESS CALCULATIONS↗

NASA NTRS1976

An analytical study of noise generation by subsonic flows in the presence of rigid surfaces

A general analytical method is developed for determination of the radiated noise field from highly sheared, subsonic flows in the presence of rigid surfaces. The method is specifically formulated to use measurable flow field properties as the basis input data for calculations. The governing equations of a viscous, incompressible fluid are employed to determine approximately the so-called shear noise source strength distribution in the flow. Mean rates of strain and fluctuating velocity covariances are the fundamental input data for calculations. The method is applied to the wall jet region of a circular jet impinging at 45 deg to an infinite plane surface. Velocity field measurements of Foss are used to describe the required flow properties. Comparisons of calculated results with measured surface pressures and sound pressure levels are given and discussed.

Wooley, J. P.↗

NASA NTRS1982

Predicting Tensile Strengths of Boron/Aluminum Composites

To develop predictive theory to account for time/temperature effect of B/A1 composites, series of deformation and fracture studies was performed on commercial boron fibers over wide ranges of stress, stress application time, and temperature. By combining these single fiber results with fracture theory for metal matrix composites, design formulas were derived that describe B/A1 composite tensile and stress rupture strengths as function of time and temperature. Using derived formulas, calculated and experimental results agree to within 3 percent.

Decarlo, J. A.↗

NASA NTRS1981

Analytical prediction of aerospace vehicle vibration environments

Considerable attention has been given recently to the formulation and validation of analytical models for the prediction of aerospace vehicle vibration response to acoustic and fluctuating pressures. This paper summarizes the development of such analytical models for two applications, (1) structural vibrations of the Space Shuttle orbiter vehicle due to broadband rocket noise and aerodynamic boundary layer turbulence, and (2) structural vibrations of general aviation aircraft due to discrete frequency propeller and reciprocating engine exhaust noise. In both cases, the spatial exterior excitations are convected pressure fields which are described on the basis of measured cross spectra (coherence and phase) information. Structural modal data are obtained from analytical predictions, and structural responses to appropriate excitation fields are calculated. The results are compared with test data, and the strengths and weaknesses of the analytical models are assessed.

Wilby, J. F.↗

NASA NTRS1982

Mechanics aspects of NDE by sound and ultrasound

Nondestructive evaluation (NDE) is considered as a means to detect the energy release mechanism of defects and the interaction of microstructures within materials with sound waves and/or ultrasonic waves. Ultrasonic inspection involves the frequency range 20 kHz-1 GHz with amplitudes depending on the sensitivity of the test instrumentation. Pulse echo systems are most frequently used in NDE. Information is extracted from the signals through measurements of the signal velocity, attenuation, the acoustic emission when stress is applied, and calculation of the acoustoelastic coefficients. Fracture properties, tensile and shear strengths, the interlaminar shear strength, the cohesive strength, yield and impact strengths, the hardness, and the residual stress can be assayed by ultrasonic methods. Finally, attention is given to analytical treatment of the derived data, with mention given to transition matrix, integral equation, and eigenstrain approaches.

Fu, L. S.↗

NASA NTRS1985

Osteocalcin as an indicator of bone metabolism during spaceflight

The effect of microgravity on osteocalcin (OC) is investigated in rats flown on Spacelab 3. Serum, Ca, Pi, total protein, alkaline phosphatase, and OC contents, and the breaking strength of the humerus of control and Spacelab rats are calculated; the procedures utilized for these analyses are described. It is detected that the OC is reduced, and the serum and alkaline phosphatase are unaffected by microgravity.

Patterson-Buckendahl, P. E.↗

NASA NTRS1989

Transferring Lens Prescriptions Between Lens-Design Programs

Optical Lens Prescription Data Formatter computer program enables user to transfer complicated lens prescriptions quickly and easily from one major optical-design program to another and back again. One can take advantage of inherent strength of either program. Programs are ACCOS V from Scientific Calculations, Inc., of Fishers, NY, and CODE V from Optical Research Associates of Pasadena, CA. VAX version written in FORTRAN.

Stacy, John E.↗

NASA NTRS1989

Oscillator strengths and electron collisional excitation cross sections for atomic oxygen

The electron-impact excitations of 12 states of O I are analyzed using a close-coupling approximation. The absorption oscillator strengths for dipole-allowed transitions among the states are calculated. Cross sections for excitation of the states by electron impact in the energy region 13.87 to 100 eV are compared with the data of Smith (1976) and Doering and Gulcicek. It is observed that there is a correlation between the data at energies 13.87, 20, and 30 eV for the (3)P-3p(5)P transition and at energies 13.87 and 16.5 eV for the (3)P-3s(5)S(0) transitions; however, for the dipole-allowed (3)P-3d(3)D(0) and (3)P-3s(prime)(3)D(0) transitions there are discrepancies in magnitude.

Tayal, S. S.↗

NASA NTRS1991

An iterative method for obtaining the optimum lightning location on a spherical surface

A brief introduction to the basic principles of an eigen method used to obtain the optimum source location of lightning is presented. The location of the optimum source is obtained by using multiple direction finders (DF's) on a spherical surface. An improvement of this method, which takes the distance of source-DF's as a constant, is presented. It is pointed out that using a weight factor of signal strength is not the most ideal method because of the inexact inverse signal strength-distance relation and the inaccurate signal amplitude. An iterative calculation method is presented using the distance from the source to the DF as a weight factor. This improved method has higher accuracy and needs only a little more calculation time. Some computer simulations for a 4DF system are presented to show the improvement of location through use of the iterative method.

Chao, Gao↗

NASA NTRS1994

The O(+) 834-A dayglow: Revised cross sections

This study assesses the impact of new O((sup 3)P) photoionization and N2 photoabsorption cross sections, and O(+) oscillator strengths and transition probabilities, on O II 834-A airglow calculations. The 834-A intensities computed using the new emission parameters are in good agreement with rocket measurements obtained in 1978 and 1980. The present study does not support a suggested reduction in the N2 photoabsorption cross section based on an earlier analysis of the rocket data. This study also explores the problem of determining F region electron densities from satellite limb scans of the O(+) 834-A emission. Our results indicate that electron density profiles inferred from limb scans are not necessarily unique; estimates of N(sub m)F(sub 2) and h(sub m)F(sub 2) can vary by at least a factor of 2 and 50 km, respectively.

Link, R.↗

NASA NTRS2013

Predicting Bone Mechanical State During Recovery After Long-Duration Skeletal Unloading Using QCT and Finite Element Modeling

During long-duration missions at the International Space Station, astronauts experience weightlessness leading to skeletal unloading. Unloading causes a lack of a mechanical stimulus that triggers bone cellular units to remove mass from the skeleton. A mathematical system of the cellular dynamics predicts theoretical changes to volume fractions and ash fraction in response to temporal variations in skeletal loading. No current model uses image technology to gather information about a skeletal site s initial properties to calculate bone remodeling changes and then to compare predicted bone strengths with the initial strength. The goal of this study is to use quantitative computed tomography (QCT) in conjunction with a computational model of the bone remodeling process to establish initial bone properties to predict changes in bone mechanics during bone loss and recovery with finite element (FE) modeling. Input parameters for the remodeling model include bone volume fraction and ash fraction, which are both computed from the QCT images. A non-destructive approach to measure ash fraction is also derived. Voxel-based finite element models (FEM) created from QCTs provide initial evaluation of bone strength. Bone volume fraction and ash fraction outputs from the computational model predict changes to the elastic modulus of bone via a two-parameter equation. The modulus captures the effect of bone remodeling and functions as the key to evaluate of changes in strength. Application of this time-dependent modulus to FEMs and composite beam theory enables an assessment of bone mechanics during recovery. Prediction of bone strength is not only important for astronauts, but is also pertinent to millions of patients with osteoporosis and low bone density.

Chang, Katarina L.↗

NASA NTRS2016

Contact and Bending Durability Calculation for Spiral-Bevel Gears

The objective of this project is to extend the capabilities of the gear contact analysis solver Calyx, and associated packages Transmission3D, HypoidFaceMilled, HypoidFaceHobbed. A calculation process for the surface durability was implemented using the Dowson-Higginson correlation for fluid film thickness. Comparisons to failure data from NASA's Spiral Bevel Gear Fatigue rig were carried out. A bending fatigue calculation has been implemented that allows the use of the stress-life calculation at each individual fillet point. The gears in the NASA test rig did not exhibit any bending fatigue failure, so the bending fatigue calculations are presented in this report by using significantly lowered strength numbers.

life↗