Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Silicon Partitioning Between Iron-Rich Metal and Silicate Melt: New Constraints From Aerodynamic Laser Levitation Furnace Experiments

The partitioning of light elements (e.g., Si, C, H, etc.) between silicate melts and iron metal alloys as a function of pressure and temperature is a critical constraint in defining the compositional evolution of planetary interiors. While there are a significant number of experimental studies in the literature that examine the various influences of oxygen fugacity, temperature, pressure, and composition on the metal-melt partitioning of silicon, it is difficult to disentangle the effects of each variable due to the nominally independent parameters (e.g., pressure, temperature, composition) being collinear. To better test for the independent effects of pressure, temperature, and melt composition on the partitioning of silicon between iron alloy and silicate melt, new high temperature (1800°–2500°C), rapid quench (~700°C/s) aerodynamic levitation laser-heating experiments in the Fe-Si-Mg-O (En65-Fa5-Si3-Fe27) system were conducted. This high temperature, low pressure method is ideal for these experiments because it eliminates the metal container as a sink for elements of interest to partition into, and it has a rapid quench rate that minimizes potential exsolution of silicon from the metal phase during quench cooling. Given the short run times of the levitation experiments (30–60 seconds), a time series at a lower temperature (1700°C) in a vertical gas-mixing muffle tube furnace was also conducted to assess equilibrium times of the bulk composition. All successful runs were imaged using back-scatter electron imaging and analyzed for phase composition using a JEOL 8530F field emission microprobe. These new data were added to a comprehensive and internally consistent data set created from published experiments, and subsequently modeled using parameters designed to minimize collinearity (e.g., optical basicity is used as a proxy for melt composition). High collinearity is found in the data set however between temperature and oxygen fugacity, precluding any model that contains both as nominally independent variables. The resulting model demonstrates a statistically significant effect of pressure, temperature, and melt composition on the partitioning of silicon in Fe-rich metal, which has implications for the formation of planetary cores in rocky planets and provides important constraints on potential bulk core compositions.

Metal↗

Thermal Expansion Calculation of Silicate Glasses at 210°C, Based on the Systematic Analysis of Global Databases

Thermal expansion data for more than 5500 compositions of silicate glasses were analyzed statistically. These data were gathered from the scientific literature, summarized in SciGlass© 6.5, a new version of the well known glass property database and information system. The analysis resulted in a data reduction from 5500 glasses to a core of 900, where the majority of the published values is located within commercial glass composition ranges and obtained over the temperature range 20 to 500°C. A multiple regression model for the linear thermal expansivity at 210°C, including error formula and detailed application limits, was developed based on those 900 core data from over 100 publications. The accuracy of the model predictions is improved about twice compared to previous work because systematic errors from certain laboratories were investigated and corrected. The standard model error (precision) was 0.37 ppm/K, with R² = 0.985. The 95% confidence interval for individual predictions largely depends on the glass composition of interest and the composition uncertainty. The model is valid for commercial silicate glasses containing Na2O, CaO, Al2O3, K2O, MgO, B2O3, Li2O, BaO, ZrO2, TiO2, ZnO, PbO, SrO, Fe2O3, CeO2, fining agents, and coloring and de-coloring components. In addition, a special model for ultra-low expansion glasses in the system SiO2-TiO2 is presented. The calculations allow optimizing the time-temperature cooling schedule of glassware, the development of glass sealing materials, and the design of specialty glass products that are exposed to varying temperatures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

LOW VELOCITY SHPERE IMPACT OF SODA LIME SILICATE GLASS

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity ( 30 m/s or 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations.

36 MATERIALS SCIENCE↗

Sorption Behavior of Iodide Ions on Calcium Silicate Hydrate Formed under the Condition Saturated with Saline Water - 17069

The sorption behavior of iodide ions on calcium-silicate-hydrate (CSH gel) under the condition saturated with saline water was examined by using a Raman spectroscopy and ICP-AES, without drying process. In the sorption experiments, I-127 is a stable isotope was used as an alternative of I-129. CSH gel was synthesized with mixing CaO, SiO{sub 2}, and NaCl solution. The Ca/Si molar ratios of CSH gel were set to 0.4, 0.8, 1.2 and 1.6, and the concentration of NaCl solution was set to 0.6 M for simulating the condition of saline groundwater. The liquid/solid weight ratios of CSH gel were set to 10, 13, 15, 17, and 20, and the total weight of solid phase was 1.5 g. Furthermore, at the preparation of CSH gel, the substance of iodide ions in each sample was adjusted to 15 μmol. The synthesis procedure for all samples was conducted in a glove bag filled with nitrogen gas. The curing period was 7, 14, 30, and 60 days at a room temperature (298 K) with shaking at 120 strokes/min. The results of the sorption experiments, iodide ions adsorbed on CSH gel regardless of the high concentration of NaCl. The concentration of iodide ions in liquid phase was equal to the initial one under all experimental conditions. Moreover, the distribution coefficients, K{sub d}, were kept constant (K{sub d} = 1 mL/g) after 14 days. In the results of Raman analysis, the structure of CSH gel was scarcely influenced by incorporating iodide ions from the viewpoint of the silicate chain. These results suggest that iodide ions will be incorporated into CSH gel with the hydration water without changing its structure. Such effect of CSH gel formed with leaching cementitious constituents around the repository may retard the migration of radionuclide (I-129) in the natural barrier of the radioactive waste disposal system. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Interactions of cesium and barium ions with calcium silicate hydrate under the condition saturated with saline water - 15247

The interaction of cesium (Cs) and barium (Ba) ions with calcium silicate hydrate (CSH gel) without drying processes was examined under the condition saturated with saline water, by monitoring the concentrations of Cs and Ba and using the Raman spectroscopy and the zeta potential. In the experiments, Ca/Si molar ratios of CSH gel were set to 0.4, 0.8, 1.2 and 1.6. Each sample was synthesized with CaO powder, SiO{sub 2} powder and NaCl solution in given combinations. The concentration of NaCl solution was set to 0.006, 0.06 and 0.6 M. At the same time, CsCl or BaCl{sub 2} solution was added to the sample in order to adjust its concentration to 1.0 mM. The curing period was set to 7, 14, 30 days. As a results, the sorption of Cs and Ba ions on CSH gel became stronger with lower Ca/Si molar ratio. On the other hand, even though the zeta potential showed the surface charge of higher Ca/Si ratio samples was positive charge which inhibits the sorption of cations, Cs and Ba ions significantly sorbed on CSH gel. In addition, Raman spectra of higher Ca/Si ratio samples showed that the degree of depolymerization of silicate chain increased with the sorption of Cs and Ba ions on CSH gel. In other words, even in higher Ca/Si ratio samples, Cs and Ba ions can sorb on CSH gel through the structural deformation of CSH gel. These results suggest that CSH gel might be able to contribute the migration retardation of Cs and/or Ba ions through the interaction with CSH gel, even if the near-field of the geological repository are saturated by saline groundwater. (authors)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Alteration Behaviors of Granite Minerals Forming Calcium Silicate Hydrate under Ca-Rich Highly Alkaline Conditions - 16160

Cementitious materials used for geological disposal systems leach large amounts of alkaline ions (Ca{sup 2+}, Na{sup +}, K{sup +}) into groundwater, and alter the pH of groundwater by up to 13. The altered groundwater contacts the host rock and forms Calcium Silicate-Hydrate (CSH) through the interaction of Ca ions and the silicate species, which in turn clogs the flow paths of the host rock. This clogging effect in the flow paths is expected to retard the migration of radionuclides. A previous study reported the heterogeneous formation of CSH on the surface of granite under Carich and highly alkaline conditions. To clarify the formation process of CSH, this study examined the CSH formation with the dissolution of some minerals contained in the granite under Ca-rich and highly alkaline conditions. In the experiments, the granite block and the crushed minerals contained in the granite were immersed in a 6.4-8.5 mM Ca(OH){sub 2} solution adjusted pH to 12.5 by adding NaOH solution. As a result, biotite and anorthite supplied more Si to the formation of CSH than other minerals. Furthermore, most of the formed CSH precipitated on the solid surface although a little CSH remained in liquid phase as supernatant. These results suggest that under Ca-rich highly alkaline conditions the CSH formed as a secondary mineral will retard the migration of radionuclides released from the repository because of the clogging effect of the flow path. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Interaction of Cesium and Barium Ions with Calcium Silicate Hydrate under a Geological Temperature Condition - 16239

The interaction of calcium-silicate-hydrate (CSH gel) and cationic radionuclides such as cesium-135 significantly affects the assessment of radionuclide migration. This study examined the influence of temperature on the interaction of Cs and barium (Ba) ions with CSH gel because temperature generally affects chemical reactions such as sorption. In the sorption experiments, CSH gel was prepared by the hydration of CaO and fumed silica without a drying process, with Ca/Si molar ratios ranging from 0.4 to 1.6 and the liquid/solid weight ratio set to 20. The concentration of Cs and/or Ba ions was adjusted to 1.0 mM. The temperature conditions during the sorption experiments for 14 days were set to 298, 313 and 333 K. As a result, the sorption of Cs ions on CSH gel increased at higher temperature. Moreover, Raman spectroscopy studies showed that the silicate chain of CSH gel depolymerized with the increase in temperature. That is, the structural deformation of CSH gel at a relatively high temperature facilitates the sorption of Cs ions. On the other hand, the sorption of Ba ions on CSH gel remained high (90 %) regardless of temperature, and hardly affected the sorption of Cs ions. These findings suggest that CSH gel around the repository is expected to further retard the migration of cationic radionuclides under temperature condition up to 333 K. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sorption Behavior of Iodate Ions on Calcium Silicate Hydrate under a High Saline Condition - 18176

The sorption behavior of iodate ions on calcium-silicate hydrate (CSH) gel under high saline condition was examined by monitoring the concentrations of iodate ions and chloride ions using ion chromatography and Raman spectroscopy, without drying process. In the sorption experiments, a stable isotope I-127 was used as an alternative of I-129 which is radioactive one. Each sample was synthesized with mixing CaO powder, SiO{sub 2} as fumed silica and NaCl solution. Ca/Si molar ratios of CSH gel were set to 0.4, 0.8, 1.2 and 1.6 (add 0.2, 0.6, 1.0 and 1.4 only L/S = 20), and the concentration of NaCl solution was set to 0 M or 0.6 M for simulating the condition of fresh or saline groundwater. The liquid/solid (L/S) ratios of CSH gel were set to 10, 15 and 20, and the total weight of solid phase was 1.5 g. At the same time, NaIO{sub 3} solution was added to the sample in order to adjust its concentration to 1.0 mM, 0.67 mM and 0.5 mM for each L/S ratios. The synthesis procedure for all samples was conducted in a glove bag filled with nitrogen gas. The curing period was 7, 14, 30, and 60 days at a room temperature (298 K) with shaking at 120 strokes/min. As a results, the concentration of iodate ions in the liquid phase decreased for all samples under experimental conditions. Besides, the sorption behavior of iodate ions were hardly changed by the concentration of NaCl. That is, iodate ions migrated to solid phase in spite of the high concentration of NaCl. The distribution coefficients, Kd, increased as Ca/Si ratio increased, and hardly depended on NaCl concentration. The results of Raman analysis shows that the structure of CSH gel was almost not changed with or without NaCl from the viewpoint of the silicate chain under this condition. These results suggest that a sorption process except for the electrostatic process such as an ion exchange and a complexation exists between CSH gel and iodate ions. Besides, CSH gel might be able to contribute the retardation for the migration of iodate ions without changing its structure, even if the disposal environment are saturated by a high saline groundwater. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ultrasmall Zeolite L Crystals Prepared from Highly Interdispersed Alkali‐Silicate Precursors

Abstract The preparation of nanosized zeolites is critical for applications where mass‐transport limitations within microporous networks hinder their performance. Often the ability to generate ultrasmall zeolite crystals is dependent upon the use of expensive organics with limited commercial relevance. Herein, we report the generation of zeolite L crystals with uniform sizes less than 30 nm using a facile, organic‐free method. Time‐resolved analysis of precursor assembly and evolution during nonclassical crystallization highlights key differences among silicon sources. Our findings reveal that a homogenous dispersion of potassium ions throughout silicate precursors leads to the formation of a metastable nonporous phase, which undergoes an intercrystalline transformation to zeolite L. The generation of highly interdispersed alkali‐silicate precursors is seemingly critical to enhancing the rate of nucleation and facilitating the formation of ultrasmall crystal.

Li, Rui↗

Spectral-Luminescent Properties of Alkoxysilane–Metallophthalocyanine Conjugates Covalently Bonded to the Polymeric Chains of Silicate Gel Materials

Conjugates of metal hydroxyl phthalocyanines (М(ОН){sub n}Рс; М = Si, Ge, Al, Ga) with 3-aminopropyltriethoxysilane (APTEOS) are synthesized. By means of the sol-gel method, polymeric silicate gel materials doped with the (APTEOS){sub n}–М(ОН){sub n}Рс conjugates are prepared: the latter form structural links in the composition of the copolymer with the siloxane fragments of the polymeric chains (in the case of n = 2) or are ″grafted″ to such chains in the form of side substituents (n = 1). It is shown by spectral-luminescent and kinetic spectroscopy methods that the (APTEOS){sub n}–М(ОН){sub n}Рс conjugates, on the introduction into a silicate gel material, retain their molecular structure and the photophysical characteristics of MPc in the monomeric form. The obtained macromolecular substances are promising as monomeric dopants in new functional materials for optics and quantum electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ruthenium supported on silicate and aluminosilicate mesoporous materials applied to selective sugar hydrogenation: Xylose to xylitol

A series of ruthenium-based catalysts supported on a set of silicate and aluminosilicate mesoporous molecular sieves was synthesized and tested in xylose hydrogenation. The materials were characterized in terms of morphology, textural properties, acidity, as well as ruthenium loading, dispersion, and oxidation state. In general, the aluminosilicates-based catalysts displayed a higher activity compared to their respective silicate supports, which can be ascribed to a higher Ru content and dispersion, enhanced by a higher acidity. The most active synthesized catalyst (Ru/Al-MCM-4) displayed an improved performance compared to a commercial Ru/C catalyst due to a better xylitol selectivity. Two modelling approaches were implemented to describe the kinetic rate. The first model was based on the hypothesis that xylose molecules and hydrogen are adsorbed in different active sites on the catalyst surface, while the second model supposes the formation of an intermediate on the catalyst surface that reacts to form xylitol. Both models gave a very good description of the experimental data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New insights into creep characteristics of calcium silicate hydrates at molecular level

The fundamental mechanisms under concrete creep are far from being fully understood, especially at the molecular level. Hereby, a calcium-silicate-hydrate (C-S-H) molecular model is developed to explain, for the first time, the creep characteristics at various stress states, temperature levels and water contents, which are not accessible experimentally. Rather tensile and compressive loadings, C-S-H only creeps under shear loadings originating from the sliding of the calcium silicate layers over each other as the interlayer component (water and ions) acts as a lubricator. A heterogeneous creep characteristic is observed. Elevated temperature reduces the interlayer lubricator viscosity and weakens the interfacial adhesion between the layers and the interlayer lubricator, which accelerates C-S-H creep. The removal of interlayer water enhances the creep resistance, resulting from the reduced interlayer space and enhanced interfacial adhesion. The atomic-level mechanisms explain the inter-CSH-particle behaviours at the microscale, which bridges the gap between atomistic simulation and microcosmic phenomenon.

36 MATERIALS SCIENCE↗

The first experimental evidence for improved nanomechanical properties of calcium silicate hydrate by polycarboxylate ether and graphene oxide

Graphene oxide (GO) efficiently enhances macroscale mechanical properties of cement-based materials. Yet the nanoscale reinforcing mechanism of GO for calcium silicate hydrate (C-S-H), the key binding phase of concrete, remains poorly understood. Moreover, how polycarboxylate ether (PCE)-based superplasticizers affect the nanomechanical properties of C-S-H remains unclear. The intrinsic mechanical properties of the nanocomposites are measured using high-pressure X-ray diffraction. The influences of GO and PCE on the local Ca and Si environments are probed using X-ray absorption spectroscopy. For the first time, we evidence that PCE-induced well-dispersed GO nanoplatelets strengthen the C-S-H basal planes, whereas poorly water-dispersed GO weakly interacts with basal planes and does not strengthen in plane Casingle bondO bonds. Both PCE and GO only slightly strengthen C-S-H's c-axis. Here, the bulk modulus of C-S-H/PCE/GO nanocomposite is 190% than pure C-S-H. Functional groups of PCE and GO prefer interacting with the Casingle bondO sheets of C-S-Hs instead of silicate tetrahedra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical structure and complex growth modes of magnesium silicate hydrate: Nanoparticle orientation, aggregation, and fusion

The extent of utilization of magnesium silicate hydrate (MSH) in construction is limited partly because of insufficient data ascertaining the kinetics of its precipitation. In this report MSH grown homogeneously or heterogeneously in the range of magnesium to silicon solution molar concentration ratios, [Mg]/[Si] = 0.5-1.5, and temperature = 25-80 °C was analyzed for its chemical structure and morphology. Infrared spectroscopy and geochemical modeling show that increasing the [Mg]/[Si] ratio results in less silicate polymerization in MSH. Atomic force microscopy reveals the presence of nanoparticles that aggregate and fuse to form films. Oriented attachment of nanoparticles and features indicative of enhanced crystallinity were observed at higher temperatures and longer reaction times. These data provide direct evidence for the persistence of hierarchical structures (i.e., nanoparticles forming 3D microparticles and 2D film layers) at the nanoscale to mesoscale. These findings offer insights into the precise chemical synthesis of MSH and its widespread use as a binder for construction purposes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silicate coating to prevent leaching from radiolabeled surrogate far-field fallout in aqueous environments

Recent characterization of radioactive particles indicate that a large percentage of the radioactivity observed during the Fukushima Daiichi nuclear meltdown was insoluble 137 Cs bound within silica microparticles. Therefore, much of the decontamination research performed prior to the Fukushima incident that used either soluble radionuclides deposited onto wet surfaces or large (~100 μm) particles characteristic of nuclear weapons fallout do not accurately represent the characteristics of potential contamination. Thus, the common practice of extrapolating radioactive decontamination methods generically to all radioactive release events is, at best, suspect. In response, a method to produce chemically-inert, radiolabeled silica particles was developed. Binding 152 Eu within a sodium silicate coating required proper temperature control and ethanol was beneficial as a volatile dispersant to limit residues. In the end, a step-wise method, which first deposited 152 Eu or 241 Am as a nitrate salt, decomposed the salt to a sesquioxide, and finally coated the surface with sodium silicate led to dispersed particles of the desired 2 or 0.5 μm diameters. Dynamic light scattering and scanning election microscopy confirmed the particle size was unchanged. Leaching studies into several common decontaminants were performed to ensure particle inertness. In this paper, our approach allows for substitution of other radionuclides making it a robust, simple, and novel method to produce inert particle surrogates for a release event that allows direct comparison of decontamination techniques and contaminant fate studies, greatly aiding the development of response and recovery plans.

61 RADIATION PROTECTION AND DOSIMETRY↗

Contrasting thermally-induced structural and microstructural evolution of alumino-silicates with tubular and planar arrangements: Case study of halloysite and kaolinite

Materials with the similar chemical structures but different morphological organization exhibit considerable differences in thermally induced chemo-morphological evolution. With recent advancements in multi-scale X-ray scattering measurements, it is now possible to non-invasively probe the structural and microstructural evolution of such materials. In this study, we investigate the chemo-morphological evolution of halloysite and contrast the results with those for kaolinite. Halloysite and kaolinite have tubular and planar morphologies, respectively. Both materials are alumino-silicates comprising silica tetrahedra (T) and alumina octahedra (O) organized in a TO structure. Four distinct stages in the structural evolution were identified. Stages I, II, III, and IV correspond to temperature ranges of 25 to 125 °C, 125 to 400 °C, 400 to 625 °C, and 625 to 875 °C. Major structural changes correspond to the removal of interlayer/adsorbed water in stage I, the existence of the halloysite structure without interlayer water in stage II, dehydroxylation of halloysite in stage III, and the conversion of ordered halloysite to amorphous meta-halloysite in stage IV. Additionally, heating halloysite up to 875 °C resulted in slight widening of the nanotubes, as the average pore radius increased from 6.4 nm to 6.6 nm. Heating also resulted in an increase of wall thickness of the nanotubes from ~120 nm (25 °C) to 161 nm (875 °C). The increase in the halloysite nanotube diameter was attributed to the expansion of the structure and an increase in the surface roughness. The pore sizes in halloysite nanotubes were also confirmed using N 2 adsorption-desorption and nano-X-ray computed tomography (nano-XCT) measurements. The interlayer basal spacing in halloysite changed from 9.8 Å to 7.2 Å after the removal of interlayer water. At temperatures in the range of 625 to 875 °C, heating halloysite causes a small widening of nanotube pores and a minor increase in the surface area. In contrast, the interlayer spacing in kaolinite collapses on heating which reduces the nanoscale porosity. Furthermore, these studies demonstrate the differences in the chemo-morphological evolution of alumino-silicates with tubular and planar morphologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silicate Carbonation in Supercritical CO2 Containing Dissolved H2O: An in situ High Pressure X-Ray Diffraction Study

Technological advances have been significant in recent years for managing environmentally harmful emissions (mostly CO2) resulting from combustion of fossil fuels. Deep underground geologic formations are emerging as reasonable options for long term storage of CO2 but mechanisms controlling rock and mineral stability in contact with injected supercritical fluids containing water are relatively unknown. In this paper, we discuss mineral transformation reactions occurring between supercritical CO2 containing water and the silicate minerals forsterite (Mg2SiO4), wollastonite (CaSiO3), and enstatite (MgSiO3). This study utilizes newly developed in situ high pressure x-ray diffraction (HXRD) and in situ infra red (IR) to examine mineral transformation reactions. Forsterite and enstatite were selected as they are important minerals present in igneous and mafic rocks and have been the subject of a large number of aqueous dissolution studies that can be compared with non-aqueous fluid tests in this study. Wollastonite, classified as a pyroxenoid (similar to a pyroxene), was chosen as a suitably fast reacting proxy for examining silicate carbonation processes associated with a wet scCO2 fluid as related to geologic carbon sequestration. The experiments were conducted under modest pressures (90 to 160 bar), temperatures between 35° to 70° C, and varying concentrations of dissolved water. Under these conditions scCO2 contains up to 3,500 ppm dissolved water.

carbon sequestration↗

Search for meteoritic GEMS II: Comparison of inclusions in amorphous silicates from the Paris chondrite and from anhydrous chondritic interplanetary dust particles

Amorphous silicates containing abundant nano-inclusions have been reported in the Paris CM chondrite (Leroux et al., 2015). They have chemical and morphological similarities to glass with embedded metal and sulfides (GEMS) found in interplanetary dust particles (IDPs) and micrometeorites believed to originate from comets. We used scanning transmission electron microscopy (STEM) with energy-dispersive X-ray spectroscopy (EDS) and nanodiffraction to study the chemistry and mineralogy of these inclusions in order to understand the origin of the GEMS-like material in Paris and its possible relationships to other materials found in primitive chondritic materials including IDP GEMS. EDS and diffraction analyses indicate compositional and mineralogical differences between the nanophase inclusions in cometary GEMS and Paris GEMS-like material. Metal inclusions are notably absent within Paris amorphous silicate. Ni-rich sulfides, including pentlandite, are common in even the least altered matrix material of Paris, while they are absent in GEMS-bearing IDPs and Ultracarbonaceous Antarctic Micrometeorites (UCAMMs). From examination of the inclusions, we cannot yet confirm or refute the possibility that GEMS-like material in Paris is related to cometary GEMS. The distinct compositions and mineralogy of the Paris material may be due to aqueous alteration of cometary GEMS precursors, but they may also denote an independent origin for meteoritic GEMS-like assemblages.

58 GEOSCIENCES↗