Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHIELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Adaptive harnessing damping in hydrokinetic energy conversion by two rough tandem-cylinders using flow-induced vibrations

Alternating lift technology (ALT) harnesses hydrokinetic energy from currents and tides and is different from conventional steady lift technologies (turbines). ALT is still under development with an important research issue being the mitigation of wake effect on downstream cylinders in Flow Induced Oscillations (FIO) of multi-cylinder Current Energy Converters (CEC). Rather than adjust the configuration/parameters of the converter, a more direct and effective way is to actively adjust the harnessed power. In this paper, a hydrokinetic energy converter using FIO of two cylinders in tandem in one-degree-of-freedom oscillators, with nonlinear adaptive damping and linear spring stiffness, is tested experimentally. FIO include Vortex Induced Vibrations (VIV), galloping, and their coexistence. Introducing adaptive damping into the tandem cylinders overcomes the shielding effect, which previous research on two tandem cylinders has shown to reduce power output by the downstream cylinder. Shielding along with fixed damping result either in ceasing motion due to excessive damping, or in low harnessed energy due to insufficient damping. In this experimental study, damping-to-velocity rate, linear spring-stiffness, cylinder spacing, and flow-velocity are the parameters with Reynolds number 30,000 ≤ Re ≤ 120,000. Comparison to linear-oscillators in FIO shows that this nonlinear converter, with velocity-proportional damping coefficient, is more effective over the entire FIO range but especially in galloping, where both flow and cylinder speeds are higher. Experimental results for energy harvesting, efficiency and instantaneous energy of the converter are presented and discussed supported by amplitude and frequency response data. Here the results show that the nonlinear, adaptive, velocity-proportional damping coefficient is an effective way to increase the overall harnessed power and the power of downstream cylinder. The harnessed power in the VIV to galloping transition increases by up to 94%. The most significant improvement is in the galloping region, where the increase in harnessed power and efficiency is around 33%.

13 HYDRO ENERGY↗
DOE OSTI2022

Hydrated Anions: From Clusters to Bulk Solution with Quasi-Chemical Theory

The interactions of hydrated ions with molecular and macromolecular solution and interface partners are strong on a chemical energy scale. Here we recount the foremost ab initio theory for the evaluation of the hydration free energies of ions, namely, quasi-chemical theory (QCT). We focus on anions, particularly halides but also the hydroxide anion, because they have been outstanding challenges for all theories. For example, this work supports understanding the high selectivity for F – over Cl – in fluoride-selective ion channels despite the identical charge and the size similarity of these ions. QCT is built by the identification of inner-shell clusters, separate treatment of those clusters, and then the integration of those results into the broader-scale solution environment. Recent work has focused on a close comparison with mass-spectrometric measurements of ion-hydration equilibria. We delineate how ab initio molecular dynamics (AIMD) calculations on ion-hydration clusters, elementary statistical thermodynamics, and electronic structure calculations on cluster structures sampled from the AIMD calculations obtain just the free energies extracted from the cluster experiments. That theory–experiment comparison has not been attempted before the work discussed here, but the agreement is excellent with moderate computational effort. This agreement reinforces both theory and experiment and provides a numerically accurate inner-shell contribution to QCT. The inner-shell complexes involving heavier halides display strikingly asymmetric hydration clusters. Asymmetric hydration structures can be problematic for the evaluation of the QCT outer-shell contribution with the polarizable continuum model (PCM). Nevertheless, QCT provides a favorable setting for the exploitation of PCM when the inner-shell material shields the ion from the outer solution environment. For the more asymmetrically hydrated, and thus less effectively shielded, heavier halide ions clustered with waters, the PCM is less satisfactory. We therefore investigate an inverse procedure in which the inner-shell structures are sampled from readily available AIMD calculations on the bulk solutions. This inverse procedure is a remarkable improvement; our final results are in close agreement with a standard tabulation of hydration free energies, and the final composite results are independent of the coordination number on the chemical energy scale of relevance, as they should be. Finally, a comparison of anion hydration structure in clusters and bulk solutions from AIMD simulations emphasize some differences: the asymmetries of bulk solution inner-shell structures are moderated compared with clusters but are still present, and inner hydration shells fill to slightly higher average coordination numbers in bulk solution than in clusters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effective Local Geometry Descriptor for 29Si NMR Q4 Anisotropy

The nuclear shielding anisotropy, ζ, is a useful nuclear magnetic resonance (NMR) shielding tensor parameter in describing the extent of electron cloud distortion about an atom. Despite the advantages afforded by NMR in structural characterization, the relationship between ζ and local structure of an atom in high-symmetry environments, such as Si-Q 4 sites, is poorly understood. Here, we use a data-driven approach combining random forest feature ranking and the Sure Independence Screening and Sparsifying Operator (SISSO) approach to derive a simple and accurate geometric descriptor for ζ with a root-mean-squared prediction error of 6.77 ppm and an R 2 of 0.761. We then apply this descriptor to describe the local geometric distortion of zeolites Sigma-2 and silica-ZSM-5 whose chemical shift anisotropy tensor has been reported. We envision that this geometric descriptor will allow for structural description and refinement in previously difficult-to-describe materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Correlated Anion Disorder in Heteroanionic Cubic TiOF 2

Resolving anion configurations in heteroanionic materials is crucial for understanding and controlling their properties. For anion-disordered oxyfluorides, conventional Bragg diffraction cannot fully resolve the anionic structure, necessitating alternative structure determination methods. We have investigated the anionic structure of anion-disordered cubic (ReO 3 -type) TiOF 2 using X-ray pair distribution function (PDF), 19 F MAS NMR analysis, density functional theory (DFT), cluster expansion modeling, and genetic-algorithm structure prediction. Our computational data predict short-range anion ordering in TiOF 2 , characterized by predominant cis-[O 2 F 4 ] titanium coordination, resulting in correlated anion disorder at longer ranges. To validate our predictions, we generated partially disordered supercells using genetic-algorithm structure prediction and computed simulated X-ray PDF data and 19 F MAS NMR spectra, which we compared directly to experimental data. To construct our simulated 19 F NMR spectra, we derived new transformation functions for mapping calculated magnetic shieldings to predicted magnetic chemical shifts in titanium (oxy)fluorides, obtained by fitting DFT-calculated magnetic shieldings to previously published experimental chemical shift data for TiF 4 . We find good agreement between our simulated and experimental data, which supports our computationally predicted structural model and demonstrates the effectiveness of complementary experimental and computational techniques in resolving anionic structure in anion-disordered oxyfluorides. From additional DFT calculations, we predict that increasing anion disorder makes lithium intercalation more favorable by, on average, up to 2 eV, highlighting the significant effect of variations in short-range order on the intercalation properties of anion-disordered materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Can ERA5 Be Used to Study Mesoscale Convective System Climatological Characteristics?

Mesoscale convective systems (MCSs) produce more than half of tropical rainfall and are central to the global hydrologic cycle. As the climate warms, environments favorable for MCSs may become more common; however, limited observational records hamper understanding of how MCSs respond to variations and changes in their environments. Here, we evaluate how well MCSs are represented in ERA5, a widely used global high‐resolution reanalysis product. Using PyFLEXTRKR, which jointly tracks top‐of‐atmosphere infrared brightness temperature and surface precipitation, we identified MCSs in ERA5 and compared them with those identified in satellite observations using the same detection algorithm. This comparison analysis spans 2007–2020 using hourly data at 0.25° horizontal resolution focusing over the tropics. ERA5 reproduces observed brightness‐temperature statistics and captures the geographic distribution and seasonal and diurnal cycles of MCS cold cloud shields. However, ERA5 precipitation exhibits an intensity bias—too much light rain and too little heavy rain—which shifts the rain‐rate distribution and reduces the frequency of MCSs relative to observations. Within MCSs, ERA5 precipitation exhibits the same pattern of bias, yielding a systematic underestimation of MCS precipitation intensity. Consistent with these biases, ERA5 underestimates the contribution of MCS to tropical rainfall by 25%–34% in key regions. Overall, ERA5 is suitable for studying MCS cold cloud‐shield climatology and evolution, but precipitation‐based MCS characteristics (including event‐level precipitation features and the geospatial distribution of MCS precipitation) should be interpreted with caution. These findings clarify which aspects of MCS behavior are robustly represented in ERA5 for climatological applications.

mesoscale convection↗
DOE OSTI2023

Functional Janus structured liquids and aerogels

Janus structures have unique properties due to their distinct functionalities on opposing faces, but have yet to be realized with flowing liquids. We demonstrate such Janus liquids with a customizable distribution of nanoparticles (NPs) throughout their structures by joining two aqueous streams of NP dispersions in an apolar liquid. Using this anisotropic integration platform, different magnetic, conductive, or non-responsive NPs can be spatially confined to opposite sides of the original interface using magnetic graphene oxide (mGO)/GO, Ti 3 C 2 T x /GO, or GO suspensions. The resultant Janus liquids can be used as templates for versatile, responsive, and mechanically robust aerogels suitable for piezoresistive sensing, human motion monitoring, and electromagnetic interference (EMI) shielding with a tuned absorption mechanism. The EMI shields outperform their current counterparts in terms of wave absorption, i.e., SE T ≈ 51 dB, SE R ≈ 0.4 dB, and A = 0.91, due to their high porosity ranging from micro- to macro-scales along with non-interfering magnetic and conductive networks imparted by the Janus architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Long-baseline quantum sensor network as dark matter haloscope

Ultralight dark photons constitute a well-motivated candidate for dark matter. A coherent electromagnetic wave is expected to be induced by dark photons when coupled with Standard-Model photons through kinetic mixing mechanism, and should be spatially correlated within the de Broglie wavelength of dark photons. Here we report the first search for correlated dark-photon signals using a long-baseline network of 15 atomic magnetometers, which are situated in two separated meter-scale shield rooms with a distance of about 1700 km. Both the network’s multiple sensors and the shields large size significantly enhance the expected dark-photon electromagnetic signals, and long-baseline measurements confidently reduce many local noise sources. Using this network, we constrain the kinetic mixing coefficient of dark photon dark matter over the mass range 4.1 feV-2.1 peV, which represents the most stringent constraints derived from any terrestrial experiments operating over the aforementioned mass range. Our prospect indicates that future data releases may go beyond the astrophysical constraints from the cosmic microwave background and the plasma heating.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Measurement of correlated charge noise in superconducting qubits at an underground facility

The charge environment of superconducting qubits may be studied through the introduction of controlled, quantified amounts of ionizing radiation. We measure space- and time-correlated charge jumps on a four-qubit device, operating 107 meters below the Earth’s surface in a low-radiation, cryogenic facility designed for the characterization of low-threshold particle detectors. The rock overburden of this facility reduces the cosmic ray muon flux by over 99% compared to laboratories at sea level. Combined with 4π coverage of a movable lead shield, this facility enables quantifiable control over the flux of ionizing radiation on the qubit device. Long-time-series charge tomography measurements on these weakly charge-sensitive qubits capture discontinuous jumps in the induced charge on the qubit islands, corresponding to the interaction of ionizing radiation with the qubit substrate. The rate of these charge jumps scales with the flux of ionizing radiation on the qubit package, as characterized by a series of independent measurements on another energy-resolving detector operating simultaneously in the same cryostat with the qubits. Using lead shielding, we achieve a minimum charge jump rate of $0.19^{+0.04}_{-0.03}$ mHz, almost an order of magnitude lower than that measured in surface tests, but a factor of roughly seven higher than expected based on reduction of ambient gammas alone. We operate four qubits for over 22 consecutive hours with zero correlated charge jumps at length scales above three millimeters.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Five-volt-class high-capacity all-solid-state lithium batteries

Advances in battery technology have been impeded by the voltage constraints of electrolytes. Here, in this study, we present a high-energy all-solid-state battery design featuring >5 V operation and an ultrahigh areal capacity of 35.3 mAh cm −2 ; these attributes were enabled by a highly conductive and ultrahigh-voltage stable fluoride solid electrolyte, LiCl–4Li 2 TiF 6 (1.7 × 10 −5 S cm −1 at 30 °C). LiCl–4Li 2 TiF 6 shields high-voltage spinel oxide cathodes, achieving 106 mAh g −1 at 2C with 75.2% retention over 500 cycles for LiNi 0.5 Mn 1.5 O 4 , sharply contrasting with the conventional LiNbO 3 counterpart, which decomposes and fails to prevent detrimental interfacial degradation. The efficacy of LiCl–4Li 2 TiF 6 is validated across various systems, including LiCoMnO 4 , LiFe 0.5 Mn 1.5 O 4 and pouch-type LiNi 0.5 Mn 1.5 O 4 ||Li (or Ag–C) all-solid-state batteries, and further demonstrated by operability down to 2.3 V with 258 mAh g −1 and ultrathick 1.8-mm electrodes. This shielding layer with >5 V stability introduces a transformative design paradigm by revisiting the previously forbidden high-voltage cathodes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrodeposition and analysis of thick bismuth films

Due to its unique physical and chemical properties, bismuth is an attractive candidate for a wide range of applications such as battery anodes, radiation shielding, and semiconductors, to name a few. This work presents the electrodeposition of mechanically stable and homogenous bismuth films at micron-scale thicknesses. A simple one-step electrodeposition process using either a pulse/reverse or direct current source yielded thick, homogenous, and mechanically stable bismuth films. Morphology, electrochemical behavior, adhesion, and mechanical stability of bismuth coatings plated with varying parameters were characterized via optical profilometry, cyclic voltammetry, electron microscopy, and tribology. Scratch testing on thick electroplated coatings (> 100 µm) revealed similar wear resistance properties between the pulse/reverse plated and direct current electroplated films. This study presents a versatile bismuth electroplating process with the possibility to replace lead in radiation shields with an inexpensive, non-toxic metal, or to make industrially relevant electrocatalytic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Comprehensive analysis of disruption mitigation methods using gas and pellet-like injections in ITER-like Tokamaks

Abstract Inert-gas shielding could be an effective mechanism for protection of plasma facing surfaces (PFS) against plasma particles impact and photon radiation heat loads during transient events in fusion devices. Neutral gas injection is one promising way to mitigate erosion of tokamak components and contamination. The objective of this work is to study and optimize mitigation methods using neutral gas and pellet-like injections to decrease the heat load to the divertor surfaces and to prevent vaporization of the various internal surfaces due to transient events in ITER-like devices. The integrated self-consistent models implemented in the HEIGHTS package was used for detailed analysis of the potential secondary plasma generation from the injected inert gas, its radiative characteristics, and shielding effectiveness. We varied the density, size, and location of an argon gas cloud to minimize the disruption energy deposited into the divertor components. We also investigated innovative ways for minor changes in ITER-like internal design to mitigate disruptions. We found the optimum parameters to fully protect ITER tokamak surfaces from erosion and vaporization during plasma instabilities. This preliminary analysis showed that using Ar gas injection methods could lead to enhancement in components lifetime in ITER-like and future DEMO devices with minor design changes.

Science & Technology - Other Topics↗
DOE OSTI2025

Solidification cracking of laser melted commercial-purity tungsten

The high melting temperature of tungsten (W) makes it an attractive candidate for energy generation applications; however, its use is limited by its poor ductility at low temperatures. This limitation affects even melt-based additive manufacturing (AM) processes such as laser powder bed fusion (PBF-LB), with as-fabricated pure W exhibiting both longitudinal and transverse cracks. Metallurgical and processing factors that affect these cracks are still being explored. This work utilizes powderless single-tracks on pure W plates made over a range of power and velocity combinations in three unique PBF-LB setups: one with flowing argon, one with continuous vacuum, and an in situ high-speed synchrotron X-ray radiography setup. Each had different oxygen activities in their build environments. Longitudinal cracks with oxides appearing to exude from the crack were found for tracks deposited in a build environment with argon shield gas, while no such cracks were observed for builds conducted in vacuum. A calculation showed that direct oxygen ingress into the melt pool from the build environment is negligible when argon shield gas is present. Thus, incorporation of spatter is a likely mechanism for oxygen ingress into the melt pool. Radiography showed extensive keyholing, spatter generation, and crack formation at keyhole porosity. A heat transfer calculation showed the crack formation time was consistent with cooling below its ductile-to-brittle transition (DBT) temperature. This work identifies solidification cracking as a feasible mechanism in pure W beyond the well-known DBT related cracking.

Materials science↗
DOE OSTI2025

NADH-bound AIF activates the mitochondrial CHCHD4/MIA40 chaperone by a substrate-mimicry mechanism

Mitochondrial metabolism requires the chaperoned import of disulfide-stabilized proteins via CHCHD4/MIA40 and its enigmatic interaction with oxidoreductase Apoptosis-inducing factor (AIF). By crystallizing human CHCHD4’s AIF-interaction domain with an activated AIF dimer, we uncover how NADH allosterically configures AIF to anchor CHCHD4’s β-hairpin and histidine-helix motifs to the inner mitochondrial membrane. The structure further reveals a similarity between the AIF-interaction domain and recognition sequences of CHCHD4 substrates. NMR and X-ray scattering (SAXS) solution measurements, mutational analyses, and biochemistry show that the substrate-mimicking AIF-interaction domain shields CHCHD4’s redox-sensitive active site. Disrupting this shield critically activates CHCHD4 substrate affinity and chaperone activity. Regulatory-domain sequestration by NADH-activated AIF directly stimulates chaperone binding and folding, revealing how AIF mediates CHCHD4 mitochondrial import. These results establish AIF as an integral component of the metazoan disulfide relay and point to NADH-activated dimeric AIF as an organizational import center for CHCHD4 and its substrates. Importantly, AIF regulation of CHCHD4 directly links AIF’s cellular NAD(H) sensing to CHCHD4 chaperone function, suggesting a mechanism to balance tissue-specific oxidative phosphorylation (OXPHOS) capacity with NADH availability.

Brosey, Chris A↗
DOE OSTI2020

Radiation driven Hohlraum using 2 ω for ICF implosions at the NIF

Radiation flux symmetry in laser-irradiated Hohlraum environments is difficult to model and control and relies on the details of plasma evolution and laser energy deposition in the harsh plasma-filled Hohlraum over the duration of the laser pulse. This study presents a conceptual design and assesses the feasibility of using lasers to create a radiation drive where the implosion symmetry relies mainly on radiation transport. In this design, the ends of a capsule containing Hohlraum are irradiated by drive laser beams that are shielded from the view of the capsule. This configuration enables the use of frequency doubled light that has a higher power and energy threshold for the current capability of NIF, up to 670 TW and ∼3.5 MJ. We estimate, using VISRAD benchmarked against HYDRA calculations, that the same drive conditions that are currently being achieved in hybridE experiments at the NIF 270–290 at the equator can be reached in this new geometry and large 6.4 mm diameter Hohlraums. The radiation drive asymmetries in this design can be mitigated by shimming the capsule ablator thickness or through tailoring the shape of the shielding to the laser spots.

Kritcher, A. L. (ORCID:0000000296941088)↗
DOE OSTI2020

Sensitive neutron transverse polarization analysis using a 3 He spin filter

Here we report an experimental implementation for neutron transverse polarization analysis that is capable of detecting a small angular change ($\ll$10 –3 rad) in neutron spin orientation. This approach is demonstrated for monochromatic beams, and we show that it could be extended to polychromatic neutron beams. Our approach employs a 3 He spin filter inside a solenoid with an analyzing direction perpendicular to the incident neutron polarization direction. The method was tested with polarized neutron beams and a spin rotator placed inside a μ -metal shield just upstream of the analyzer. No cryogenic superconducting shields or additional neutron spin manipulations are needed. With a counting detector, we experimentally show that the angular resolution δ θ = 1 / ( P n A N ) rad is only determined by the counting statistics for the total counts N and the product of the neutron polarization P n and the analyzing power A . With a high-flux neutron beam, 10 –6 rad angular sensitivity is feasible within a day. This simple, classical-quantum-limited transverse polarization analysis scheme may reduce the overall complexity of experimental implementation for applications requiring sensitive neutron polarimetry and improve the precision in fundamental science studies and polarized neutron imaging.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

A neutron recoil-spectrometer for measuring yield and determining liner areal densities at the Z facility

For this study, a proof-of-principle CR-39 based neutron-recoil-spectrometer was built and fielded on the Z facility. Data from this experiment match indium activation yields within a factor of 2 using simplified instrument response function (IRF) models. The data also demonstrates the need for neutron shielding in order to infer liner areal densities. A new shielded design has been developed. The spectrometer is expected to achieve signal-to-background greater than 2 for the down-scattered neutron signal and greater than 30 for the primary signal.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Spectroscopic signature of negative electronic compressibility from the Ti core-level of titanium carbonitride MXene

Two-dimensional transition metal carbides, carbonitrides, and nitrides called MXenes exhibit high metallic conductivity, ion intercalation capability and reversible redox activity, prompting their applications in energy storage and conversion, electromagnetic interference (EMI) shielding, and electronics, among many other fields. It has been shown that replacement of about 50% of carbon atoms in the most popular MXene family member, titanium carbide (Ti 3 C 2 T x ), by nitrogen atoms, forming titanium carbonitride (Ti 3 CNT x ), leads to drastically different properties, such as very high negative charge in solution and extreme EMI shielding effectiveness, exceeding all known materials, even metals at comparable thicknesses. Here, by using ultraviolet photoemission spectroscopy (UPS), the electronic structures of Ti 3 CNT x and Ti 3 C 2 T x are systematically investigated and compared as a function of charge carrier density. We observe that, in contrast to Ti 3 C 2 T x , the Ti 3p core-level of Ti 3 CNT x exhibits a counterintuitive shift to a lower binding energy of up to approximately 250 meV upon increasing the electron density, which is a spectroscopic signature of negative electronic compressibility (NEC). These experimentally measured chemical potential shifts are well-captured by the density functional theory (DFT) calculation. The DFT results also further suggest that the hybridization of titanium-nitrogen bonding in Ti 3 CNT x helps promoting the available states of Ti atoms for receiving more electron above the Fermi level and leads to the observed NEC. Furthermore, our findings explain the differences in electronic properties between the two very important and widely studied MXenes and also suggest a new strategy to apply the NEC effect of Ti 3 CNT x in energy and charge storage applications.

2D materials↗
DOE OSTI2021

Converting existing optical detectors into fast x-ray detectors

Here, the very short burn time and small size of burning plasmas created at advanced laser-fusion facilities will require high-spatial-resolution imaging diagnostics with fast time resolution. These instruments will need to function in an environment of extremely large neutron fluxes that will cause conventional diagnostics to fail because of radiation damage and induced background levels. One solution to this challenge is to perform an ultrafast conversion of the x-ray signals into the optical regime before the neutrons are able to reach the detector and then to relay image the signal out of the chamber and into a shielded bunker, protected from the effects of these neutrons. With this goal in mind, the OMEGA laser was used to demonstrate high-temporal-resolution x-ray imaging by using an x-ray snout to image an imploding backlighter capsule onto a semiconductor. The semiconductor was simultaneously probed with the existing velocity interferometry system for any surface reflector (VISAR) diagnostic, which uses an optical streak camera and provided a one-dimensional image of the phase in the semiconductor as a function of time. The phase induced in the semiconductor was linearly proportional to the x-ray emission from the backlighter capsule. This approach would then allow a sacrificial semiconductor to be attached at the end of an optical train with the VISAR and optical streak camera placed in a shielded bunker to operate in a high neutron environment and obtain time-dependent one-dimensional x-ray images or time-dependent x-ray spectra from a burning plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗