Results for “Product design” — Page 25

DOE OSTI2022

Critical Analysis of Replacements for R-410A in Heat Pump Applications

Using low-GWP refrigerants can reduce the Green House Gas (GHG) emission of HVAC systems. Research has shown that using heat exchangers with small diameter tubes is a promising solution to meet the performance goals of heat pump using low-GWP refrigerants due to reduced refrigerant charge, reduced flammable impact and environmental impact. However, application of small diameter tube requires in-depth component design optimization to make the new system adapt to low-GWP refrigerants.In this paper, multi-objective optimizations using Particle Swarm Optimization (PSO) algorithm on a R-410A residential 5-ton air source heat pump is performed for improved system performance and reduced material cost. Five R-410A alternatives, i.e., R-32, R-454A, R-454B, R-454C and R-455A are investigated. R-455A and R-454C have GWP lower than 150. As a result of optimization, 12.4%-19.1% Energy Efficiency Ratio (EER) improvement and up to 71% HXs material cost saving is achieved. Life Cycle Climate Performance (LCCP) analysis shows that optimized systems reduce total CO2 emission by 13%-33% depending on the choice of refrigerant and climate zone.The optimal heat exchangers resulting from this research can fit into the original R-410A fan-coil units. The proposed heat pump design method establishes a production and installation path to produce cost-effective low-GWP heat pumps easily accepted by end users.

Li, Zhenning↗

DOE OSTI2022

Fabrication experience of the pre-production PIP-II SSR2 cavities at Fermilab

The Proton Improvement Plan-II (PIP-II, [1]) linac will include 35 Single Spoke Resonators type 2 (SSR2). A total of eight pre-production SSR2 jacketed cavities will be procured and five installed in the first pre-production cryomodule. The mechanical design of the jacketed cavity has been finalized and it will be presented in this paper along with fabrication and processing experience. The importance of interfaces, quality controls and procurement aspects in the design phase will be remarked as well as lessons learned during the fabrication process. Furthermore, development studies will be presented together with other design validation tests.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Optimization of a Residential Air Source Heat Pump using Refrigerants with GWP <150 for Improved Performance and Reduced Emission

Using low-GWP refrigerants can reduce the Green House Gas (GHG) emission of heat pump systems. Heat exchangers and compressors are the key components and have a prominent impact on system performance, significant research is devoted to reducing the cost of the heat exchangers while achieving the same or better system performance with refrigerant charge reduction.To better understand the environmental impacts of optimized systems with low-GWP refrigerants, Life Cycle Climate Performance (LCCP) evaluation method was used to evaluate the direct and indirect emissions of the system over the course of its lifetime from manufacturing to disposal. The DOE/ORNL Heat Pump Design Model (HPDM) is used to evaluate the performance of heat pumps. Multi-objective optimizations using Particle Swarm Optimization (PSO) algorithm are performed on a 3-ton R410A residential air source heat pump on market. Seven R410A alternatives, i.e., R32, R454B, R454C, R455A, R457A, R1234yf and R1234ze(E) are investigated. The last five fluids have GWP lower than 150.As a result, 5.5%-12.8% seasonal energy efficiency ratio 2 (SEER2) improvement is achieved, and the optimized systems reduce life cycle CO2 emission by 8.5%-28.6% with GWP lower than 150 refrigerants. The optimal heat exchangers can fit into the original R410A fan-coil units; therefore, the proposed design method establishes a production and installation path to produce cost-effective low-GWP heat pumps easily accepted by end users.

Li, Zhenning↗

DOE OSTI2025

The Profiled Feldman-Cousins Method for Confidence Interval Construction for the Nova 3-Flavor Oscillation Analysis

The small interaction cross-section of neutrinos makes experimental neutrino physics particularly responsive to technological advancements. A significant development leveraged by the NOvA experiment is large-scale parallel processing, enabling novel computational approaches to longstanding experimental challenges. Central to managing the resulting high-throughput data is NOvA’s implementation of the Freight Train model, designed for efficient data production and handling.This dissertation details the methodology and execution of the NOvA 2024 3-Flavor Oscillation Analysis, supported by a comprehensive dataset spanning ten years. It emphasizes frequentist results refined through the Feldman-Cousins (FC) technique, specifically addressing confidence interval corrections in parameter estimation. The computational intensity associated with Feldman-Cousins arises from extensive Monte Carlo simulations, which were substantially mitigated through parallel computing on the Perlmutter supercomputer at the National Energy Research Scientific Computing Center (NERSC), employing the MPI framework.To further enhance computational efficiency, an Importance Sampling method is introduced and evaluated, demonstrating significant potential to reduce complexity, particularly in exploring extreme parameter space regions. This thesis presents both the successful application of advanced computational resources and the development of sophisticated statistical techniques, aiming to enhance the precision and scope of neutrino oscillation analyses.

Dye ajdye11190@gmail.com, Andrew Joseph [Mississip↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2024

Scientific Foundations and Approaches for Qualification of Additively Manufactured Structural Components

Additive manufacturing (AM) maintains a wide process window that enables complex designs otherwise unattainable via conventional production technologies. However, the lack of confidence in qualifying AM parts that leverage AM process–structure–property–performance (PSPP) relationships stymies design optimization and adoption of AM. While continuing efforts to map fundamental PSPP relationships that cover the potential design space, we first need pragmatic and then long-term solutions that overcome challenges associated with qualifying AM-designed parts. Two pragmatic solutions include: (1) AM material specifications to substantiate process reproducibility, and (2) component risk categorization to associate system risk relative to part performance and required part quality. A novel qualification paradigm under development involves efficient prediction of part performance over wide-ranging PSPP relationships through targeted testing and computational simulation. Here this paper describes projects at Sandia National Laboratories on PSPP relationship discovery, these pragmatic approaches, and the novel qualification approach.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Design and Optimization of Processing Pathways for Rare Earth Element Recovery from End-of-Life Products

In this presentation, we first discuss the benefits of targeting end-of-life (EOL) products as a feedstock. We then discuss the problem statement of designing a processing facility for recovering rare earth elements (REEs) from EOL HDDs and motors from EOL EVs/HEVs. We then discuss the most profitable pathway, and then discuss the environmental impacts associated with the processing pathway, comparing it to a processing facility in China, and find it to have lower impacts overall. We also investigate the trade-off solutions for other pathways that are not as profitable, but have lower impacts by generating Pareto Fronts. In the next portion of the presentation, Critical Materials Recycling, Inc. is discussed. We discuss how their process was found to be the optimal pathway after performing superstructure optimization, and how we are currently working with them to further optimize their process to increase profits. Finally, we wrap up with conclusions summarizing the main takeaways of the presentation.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Integration of High-Z Converter into Full-scale Production Target for Accelerator-based Production of 99 Mo

NorthStar Medical Technologies is planning to produce the 99Mo isotope via the photonuclear route. The Rhodotron accelerator designed by IBA will be used as an electron-beam source. The Rhodotron is an efficient recirculating accelerator, providing low energy dispersion and a low-emittance electron beam. The nominal beam power is assumed to be 120 kW at 40 MeV. In photonuclear production of 99 Mo, a high-power electron beam impinges on a helium-cooled Mo disk target. Electrons are converted into photons through the Bremsstrahlung process. Consequently, high-energy photons interact with the target nuclei, producing 99 Mo through the 100 Mo(γ, n) 99 Mo reaction. Traditionally, photonuclear production is realized using high-Z material as the electron-to-photon converter. NorthStar plans not to use a high-Z converter in the initial production target design, but it may be interested in the increased production capabilities a high-Z converter can provide. The purpose of this report is to evaluate the advantages and disadvantages of incorporating a high-Z converter into the target design.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2020

Accident-Tolerant Fuel

Advanced light water reactor (LWR) fuels have been developed incrementally for more than 60 years before the term Accident Tolerant Fuel (ATF) was created. There are many different categories of ATF concepts, which range from near-term marginal enhancements to fission gas release in fuel or hydrogen pickup in the cladding, to transformational fuel types with new engineered fission product barriers. In this work we characterize these different types of ATF, and give several important examples for each.We conclude that transformational ATF concepts have the greatest potential to enhance the traditional definition of defense-in-depth by enhancing current barriers and/or by providing additional barriers to fission product release. This objective can primarily be achieved by introducing a new fission product barrier that enhances defense-in-depth by design, for example the added barriers to fission product release in some engineered ATF concepts. We recommend future gap analyses and a phenomena identification and ranking to assess the applicability of existing safe acceptable fuel design limits and the standard review plan to specific ATF concepts.

Brown, Nicholas↗

DOE OSTI2021

Transformational Challenge Reactor Safety Design and Radionuclide Retention Strategy

An integrated safety design and radionuclide (RN) retention strategy is developed to support the Transformational Challenge Reactor (TCR) demonstration. This demonstration aims to showcase viability for rapid deployment of a novel reactor by leveraging the advances in materials, manufacturing, and computational sciences through a highly integrated and agile design and development approach. This strategy provides a logical description and understanding of how RNs are contained within the facility. Rather than discussing fission product barriers individually between separate design and safety basis reports, this paper provides a consistent description and narrative to better facilitate regulatory interactions and focus safety design efforts. The principal barriers credited include the various coating layers in the tristructural isotropic (TRISO) fuel particle, the silicon carbide (SiC) matrix hosting the particles within the fuel element, the helium pressure boundary, and the confinement system. The choice and assumed performance of the credited barriers are highly conservative, which is a direct reflection of the low hazard that the TCR demonstration presents and the need to simplify and focus the safety review process accordingly. However, the strategy and the associated framework are generalized and may be adopted and tailored to support other advanced reactor demonstration efforts.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

FECM/NETL Unconventional Shale Well Economic Model (UShWEM): Production Data for UShWEM

The Production Data for UShWEM.xlsx is an Excel file that is formatted and organized similarly to the Production Streams sheet of the FECM/NETL Unconventional Shale Well Economic Model (UShWEM). The purpose of this file is to allow the user to import completion design and time-series production data for hundreds of wells into the UShWEM easily and quickly, and have their well data saved safely in an external location. For instructions on how to use the Production Data for UShWEM.xlsx file, see section 2.3 of the FECM/NETL Unconventional Shale Well Economic Model: User’s Manual.

Sheriff, Alana↗

DOE OSTI2021

Decision-Making Under Uncertainty for a Digital Thread-Enabled Design Process

Abstract Digital thread is a data-driven architecture that links together information from all stages of the product lifecycle. Despite increasing application in manufacturing, maintenance/operations, and design related tasks, a principled formulation of analyzing the decision-making problem under uncertainty for the digital thread remains absent. The contribution of this article is to present a formulation using Bayesian statistics and decision theory. First, we address how uncertainty propagates in the product lifecycle and how the digital thread evolves based on the decisions we make and the data we collect. By using these mechanics, we explore designing over multiple product generations or iterations and provide an algorithm to solve the underlying multistage decision problem. We illustrate our method on an example structural design problem where our method can quantify and optimize different types and sequences of decisions, ranging from experimentation, manufacturing, and sensor placement/selection, to minimize total accrued costs.

Engineering↗

DOE OSTI2021

Reliability-Informed Economic and Energy Evaluation for Design for Remanufacturing: A Case Study on a Hydraulic Manifold

Design for Remanufacturing (DfRem) is an attractive approach for sustainable product development. Evaluation of DfRem strategies, from both economic and environmental perspectives, at an early design stage can allow the designers to make informed decisions when choosing the best design option. Studying the long-term implications of a particular design scenario requires quantifying the benefits of remanufacturing for multiple life cycles while considering the reliability of the product. In addition to comparing designs on a one-to-one basis, we find that including reliability provides a different insight into comparing design strategies. We present a reliability-informed cost and energy analysis framework that accounts for product reliability for multiple remanufacturing cycles within a certain warranty policy. The variation of reuse rate over successive remanufacturing cycles is formulated using a branched power-law model which provides probabilistic scenarios of reusing or replacing with new units. To demonstrate the utility of this framework, we use the case study of a hydraulic manifold, which is a component of a transmission used in some agricultural equipment, and use real-world field reliability data to quantify the transmission’s reliability. Three design improvement changes are proposed for the manifold and we quantify the costs and energy consumption associated with each of the design changes for multiple remanufacturing cycles.

design for remanufacturing↗

DOE OSTI2024

One-Pot Self-Assembly of Sequence-Controlled Mesoporous Heterostructures via Structure-Directing Agents

Multimaterial heterostructures have led to characteristics surpassing the individual components. Nature controls the architecture and placement of multiple materials through biomineralization of nanoparticles (NPs); however, synthetic heterostructure formation remains limited and generally departs from the elegance of self-assembly. Here, in this study, a class of block polymer structure-directing agents (SDAs) are developed containing repeat units capable of persistent (covalent) NP interactions that enable the direct fabrication of nanoscale porous heterostructures, where a single material is localized at the pore surface as a continuous layer. This SDA binding motif (design rule 1) enables sequence-controlled heterostructures, where the composition profile and interfaces correspond to the synthetic addition order. This approach is generalized with 5 material sequences using an SDA with only persistent SDA-NP interactions (“P-NP 1 –NP 2 ”; NP i = TiO 2 , Nb 2 O 5 , ZrO 2 ). Expanding these polymer SDA design guidelines, it is shown that the combination of both persistent and dynamic (noncovalent) SDA-NP interactions (“PD-NP 1 –NP 2 ”) improves the production of uniform interconnected porosity (design rule 2). The resulting competitive binding between two segments of the SDA (P- vs D-) requires additional time for the first NP type (NP 1 ) to reach and covalently attach to the SDA (design rule 3). The combination of these three design rules enables the direct self-assembly of heterostructures that localize a single material at the pore surface while preserving continuous porosity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

An Algal Nutrient‐Replete, Optimized Medium for Fast Growth and High Triacylglycerol Accumulation

Microalgae are promising sources to sustainably meet the global needs for energy and products. Algae grow under different trophic conditions, where nutritional status regulates biosynthetic pathways, energy production, and growth. The green alga Chromochloris zofingiensis has strong economic potential because it co-produces biofuel precursors and the high-value antioxidant astaxanthin while accumulating biomass when grown mixotrophically. As an emerging reference alga for photosynthesis, metabolism, and bioproduction, C. zofingiensis needs a defined, optimized medium to standardize experiments during fast growth for batch cultivation. Because the interplay of glucose treatment (+Glc) and mineral deficiency influences photosynthesis, growth, and the production of lipids and astaxanthin, we designed a replete nutrient medium tailored to the C. zofingiensis cellular ionome. We combined inductively coupled plasma mass spectrometry (ICP-MS) and +Glc growth curves to determine a medium that is nutrient replete for at least 5 days of +Glc logarithmic growth. We found that there are high nutritional needs for phosphorus and sulfur during mixotrophy. Iron was the only element measured for which the cellular concentration correlated with exogenous concentration and was iteratively adjusted until the cellular ionome was consistent through the logarithmic growth phase. This Chromochloris-Optimized Ratio of Elements (CORE) medium supports fast growth and high biomass and lipid accumulation without causing excess nutrient toxicity. This defined, nutrient-replete standard is important for future C. zofingiensis investigations and can be adapted for other species to support high biomass for batch cultivation. The method used to develop CORE medium shows how ionomics informs replicable media design and may be applied in industrial settings to inform cost-effective biofuel production.

Jeffers, Tim L. [University of California, Berkele↗

DOE OSTI2020

Advanced light source-Upgrade accumulator-ring gas bremsstrahlung production

Lawrence Berkeley National Laboratory is designing a new electron synchrotron for scientific research using synchrotron radiation. An upgrade of the Advanced Light Source (ALS) would position the nation to retain its international competitiveness in the soft X-ray sciences. The ALS is a 1.9 GeV storage ring operating at 500 mA of beam current. It is optimized to produce intense beams of soft X-rays, which offer spectroscopic contrast, nanometer-scale resolution, and broad temporal sensitivity. Upgrading the ALS storage ring from a triple-bend-achromat to a multibend-achromat (MBA) lattice design will provide a soft X-ray source that is up to 100–1,000 times brighter than today’s ALS and will provide a significantly higher fraction of coherent light in the soft X-ray region than is currently available at the ALS. Further, the upgraded ALS will offer the highest coherent flux of any existing or planned storage-ring facility, worldwide, up to a photon energy of 3.5 keV. The addition of an accumulator ring that enables on-axis, swap-out, recovery, and exchange of bunch trains is required to achieve this coherence and brightness. Analysis of the radiation generated and shielding required by the addition of this new accelerator is presented in this paper.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Energy Efficiency Requirements for Acquisition Professionals

Federal agencies are required to purchase products as certified by EPA or designated by DOE’s Federal Energy Management Program (FEMP). The two programs cover different products, sizes and applications. These requirements also have an associated FAR clause, FAR 52.223-15. They apply to both energy-consuming products and services that use energy-consuming products.

Ackerman, Allison↗