Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process settings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

DDS-Suite - A Dynamic Data Acquisition, Processing, and Analysis System for Wind Tunnel Testing

Wind Tunnels have optimized their steady-state data systems for acquisition and analysis and even implemented large dynamic-data acquisition systems, however development of near real-time processing and analysis tools for dynamic-data have lagged. DDS-Suite is a set of tools used to acquire, process, and analyze large amounts of dynamic data. Each phase of the testing process: acquisition, processing, and analysis are handled by separate components so that bottlenecks in one phase of the process do not affect the other, leading to a robust system. DDS-Suite is capable of acquiring 672 channels of dynamic data at rate of 275 MB / s. More than 300 channels of the system use 24-bit analog-to-digital cards and are capable of producing data with less than 0.01 of phase difference at 1 kHz. System architecture, design philosophy, and examples of use during NASA Constellation and Fundamental Aerodynamic tests are discussed.

Burnside, Jathan J.↗
NASA NTRSDate not supplied

Preparation for and Performance of a Pseudomonas aeruginosa Biofilm Experiment On Board the International Space Station

Biofilms are a problem on Earth given their ability to degrade the materials upon which they grow and due to their relevance to infections. Remarkably, 65% and 80% of infections and chronic diseases on Earth are associated with biofilms, respectively. In space, these problems' impact is higher because the crew's lives and mission success depend on nominal operation of mechanical systems. Furthermore, the isolated confined environment nature of spaceflight may increase the rates of disease transmission. In the case of the International Space Station (ISS), biofilms are an identified problem on the Environmental Control and Life Support System (ECLSS), namely on the water processor assembly (WPA). In late 2019, the Space Biofilms experiment launched towards ISS to (i) characterize the mass, thickness, morphology, and gene expression of biofilms formed in space with respect to matched Earth controls, (ii) interrogate the expression of antimicrobial resistance genes, and (iii) test novel materials as potential biofilm control strategies for future ECLSS components. For this, 288 bacterial samples were prepared prior to the launch of the Northrop Grumman CRS-12 mission from NASA's Wallops Flight Facility. The samples were integrated into the spaceflight hardware, BioServe's Fluid Processing Apparatus (FPA) packed in sets of eight in Group Activation Packs (GAP). Half of these samples were activated and terminated on orbit by NASA astronauts Jessica Meir and Christina Koch, while the remaining half were processed equivalently on Earth. The spaceflight bacterial samples of Space Biofilms returned on board SpaceX' CRS-19 Dragon spacecraft, in early 2020. We here describe the test campaign implemented to verify the experiment design and confirm it would enable us to achieve the project's scientific goals. This campaign ended with the Experiment Verification Test (EVT), from which we here present example morphology and transcriptomic results. We describe in detail the sample preparation prior to flight, including cleaning and sterilization of the coupons of six materials (SS316, passivated-SS316, lubricant impregnated surface, catheter-grade silicone with and without a nanotopography, and cellulose membrane), loading and integration of growth media, bacterial inoculum, fixative and preservative to enable experiment termination on orbit. Additionally, we describe the performance of the experiment on board the ISS, including crew activities, use of assets, temperature profile, and experiment timeline; all leading to a successful spaceflight experiment.

Pamela Flores↗
NASA NTRS1981

SPAR data set contents

The contents of the stored data sets of the SPAR (space processing applications rocket) finite element structural analysis system are documented. The data generated by each of the system's processors are stored in a data file organized as a library. Each data set, containing a two-dimensional table or matrix, is identified by a four-word name listed in a table of contents. The creating SPAR processor, number of rows and columns, and definitions of each of the data items are listed for each data set. An example SPAR problem using these data sets is also presented.

Cunningham, S. W.↗
NASA NTRS1996

Variance Analysis of Unevenly Spaced Time Series Data

We have investigated the effect of uneven data spacing on the computation of delta (sub chi)(gamma). Evenly spaced simulated data sets were generated for noise processes ranging from white phase modulation (PM) to random walk frequency modulation (FM). Delta(sub chi)(gamma) was then calculated for each noise type. Data were subsequently removed from each simulated data set using typical two-way satellite time and frequency transfer (TWSTFT) data patterns to create two unevenly spaced sets with average intervals of 2.8 and 3.6 days. Delta(sub chi)(gamma) was then calculated for each sparse data set using two different approaches. First the missing data points were replaced by linear interpolation and delta (sub chi)(gamma) calculated from this now full data set. The second approach ignored the fact that the data were unevenly spaced and calculated delta(sub chi)(gamma) as if the data were equally spaced with average spacing of 2.8 or 3.6 days. Both approaches have advantages and disadvantages, and techniques are presented for correcting errors caused by uneven data spacing in typical TWSTFT data sets.

Hackman, Christine↗
NASA NTRS2005

Analytical Laboratory Science on the 2009 Mars Science Laboratory (MSL) Mission

The Odyssey Missions orbital maps of near surface ice abundance using neutron spectroscopy (Boynton et al., 2002), the Mars Exploration Rover s confirmation of aqueous processing (Squyres et al., 2004), and the Mars Express detailed infrared maps of specific mineral types that were likely formed in aqueous environments (Bibring et al., 2005) have dramatically expanded our tool set for understanding of aqueous processes on Mars. The 2009 Mars Science Laboratory is designed to extend the "follow the water" crosscutting theme of the Mars Exploration Program toward an even more detailed exploration of habitability - the potential of the Mars environment to support life. The next steps in understanding the habitability of Mars are a more detailed in situ analysis of the chemical state of elements such as C, H, O, N, S, P, Ca, and Fe that are essential for terrestrial life. Of particular interest are experiments that establish definitive mineralogy for a wider range of compounds and those that implement a more comprehensive and sensitive search for organic molecules both in the atmosphere and in surface or near surface rocks, soils, and fines. The recent reports of atmospheric methane in the Martian atmosphere make the organics exploration even more compelling. The substantial mass and power resources of MSL combined with its mobility and powerful sample acquisition and processing tools will enable it to locate a variety of near-surface samples and analyze these in some detail. NASA is presently considering the possibility of landing a second MSL rover in 2011.

Mahaffy, P. R.↗
NASA NTRS1994

Assessment of the SFC database for analysis and modeling

SFC is one of the four clusters that make up the Integrated Work Control System (IWCS), which will integrate the shuttle processing databases at Kennedy Space Center (KSC). The IWCS framework will enable communication among the four clusters and add new data collection protocols. The Shop Floor Control (SFC) module has been operational for two and a half years; however, at this stage, automatic links to the other 3 modules have not been implemented yet, except for a partial link to IOS (CASPR). SFC revolves around a DB/2 database with PFORMS acting as the database management system (DBMS). PFORMS is an off-the-shelf DB/2 application that provides a set of data entry screens and query forms. The main dynamic entity in the SFC and IOS database is a task; thus, the physical storage location and update privileges are driven by the status of the WAD. As we explored the SFC values, we realized that there was much to do before actually engaging in continuous analysis of the SFC data. Half way into this effort, it was realized that full scale analysis would have to be a future third phase of this effort. So, we concentrated on getting to know the contents of the database, and in establishing an initial set of tools to start the continuous analysis process. Specifically, we set out to: (1) provide specific procedures for statistical models, so as to enhance the TP-OAO office analysis and modeling capabilities; (2) design a data exchange interface; (3) prototype the interface to provide inputs to SCRAM; and (4) design a modeling database. These objectives were set with the expectation that, if met, they would provide former TP-OAO engineers with tools that would help them demonstrate the importance of process-based analyses. The latter, in return, will help them obtain the cooperation of various organizations in charting out their individual processes.

Centeno, Martha A.↗
NASA NTRS1989

Strategies for automatic planning: A collection of ideas

The main goal of the Jet Propulsion Laboratory (JPL) is to obtain science return from interplanetary probes. The uplink process is concerned with communicating commands to a spacecraft in order to achieve science objectives. There are two main parts to the development of the command file which is sent to a spacecraft. First, the activity planning process integrates the science requests for utilization of spacecraft time into a feasible sequence. Then the command generation process converts the sequence into a set of commands. The development of a feasible sequence plan is an expensive and labor intensive process requiring many months of effort. In order to save time and manpower in the uplink process, automation of parts of this process is desired. There is an ongoing effort to develop automatic planning systems. This has met with some success, but has also been informative about the nature of this effort. It is now clear that innovative techniques and state-of-the-art technology will be required in order to produce a system which can provide automatic sequence planning. As part of this effort to develop automatic planning systems, a survey of the literature, looking for known techniques which may be applicable to our work was conducted. Descriptions of and references for these methods are given, together with ideas for applying the techniques to automatic planning.

Collins, Carol↗
NASA NTRS1998

A Framework for Preliminary Design of Aircraft Structures Based on Process Information

This report discusses the general framework and development of a computational tool for preliminary design of aircraft structures based on process information. The described methodology is suitable for multidisciplinary design optimization (MDO) activities associated with integrated product and process development (IPPD). The framework consists of three parts: (1) product and process definitions; (2) engineering synthesis, and (3) optimization. The product and process definitions are part of input information provided by the design team. The backbone of the system is its ability to analyze a given structural design for performance as well as manufacturability and cost assessment. The system uses a database on material systems and manufacturing processes. Based on the identified set of design variables and an objective function, the system is capable of performing optimization subject to manufacturability, cost, and performance constraints. The accuracy of the manufacturability measures and cost models discussed here depend largely on the available data on specific methods of manufacture and assembly and associated labor requirements. As such, our focus in this research has been on the methodology itself and not so much on its accurate implementation in an industrial setting. A three-tier approach is presented for an IPPD-MDO based design of aircraft structures. The variable-complexity cost estimation methodology and an approach for integrating manufacturing cost assessment into design process are also discussed. This report is presented in two parts. In the first part, the design methodology is presented, and the computational design tool is described. In the second part, a prototype model of the preliminary design Tool for Aircraft Structures based on Process Information (TASPI) is described. Part two also contains an example problem that applies the methodology described here for evaluation of six different design concepts for a wing spar.

Rais-Rohani, Masoud↗
NASA NTRS2006

Increasing Efficiency at the NTF by Optimizing Model AoA Positioning

The National Transonic Facility (NTF) at NASA Langley Research Center (LaRC) is a national resource for aeronautical research and development. The government, military and private industries rely on the capability of this facility for realistic flight data. Reducing the operation costs and keeping the NTF affordable is essential for aeronautics research. The NTF is undertaking an effort to reduce the time between data points during a pitch polar. This reduction is being driven by the operating costs of a cryogenic facility. If the time per data point can be reduced, a substantial cost savings can be realized from a reduction in liquid nitrogen (LN2) consumption. It is known that angle-of-attack (AoA) positioning is the longest lead-time item between points. In January 2005 a test was conducted at the NTF to determine the cause of the long lead-time so that an effort could be made to improve efficiency. The AoA signal at the NTF originates from onboard instrumentation then travels through a number of different systems including the signal conditioner, digital voltmeter, and the data system where the AoA angle is calculated. It is then fed into a closed loop control system that sets the model position. Each process along this path adds to the time per data point affecting the efficiency of the data taking process. Due to the nature of the closed loop feed back AoA control and the signal path, it takes approximately 18 seconds to take one pitch pause point with a typical AoA increment. Options are being investigated to reduce the time delay between points by modifying the signal path. These options include: reduced signal filtering, using analog channels instead of a digital volt meter (DVM), re-routing the signal directly to the AoA control computer and implementing new control algorithms. Each of these has potential to reduce the positioning time and together the savings could be significant. These timesaving efforts are essential but must be weighed against possible loss of data quality. For example, a reduction in filtering can introduce noise into the signal and using analog channels could result in some loss of accuracy. Data quality assessments need to be performed concurrently with timesaving techniques since data quality parameters are essential in maintaining facility integrity. This paper will highlight time saving efforts being undertaken or studied at the NTF. It will outline the instrumentation and computer systems involved in setting of the model pitch attitude then suggest changes to the process and discuss how these system changes would effect the time between data points. It also discusses the issue of data quality and how the potential efficiency changes in the system could affect it. Lastly, it will discuss the possibility of using an open loop control system and give some pros and cons of this method.

Crawford, Bradley L.↗
NASA NTRSDate not supplied

Recalibration of the NASA Exterior Effects Room

The Exterior Effects Room (EER) is a psychoacoustic testing facility at NASA Langley Research Center which primarily focuses on testing human response to aircraft noise. The 39-seat auditorium houses a real-time spatial audio system and flyover simulation environment. The audio server utilizes an implementation of three-dimensional vector base amplitude panning (VBAP), a perceptual spatial audio technique exploiting loudspeaker triplets to place a virtual sound source at an arbitrary spatial position. Due to the irregular room geometry and nonuniform loudspeaker setup, the audio server applies equalization filtering to compensate for spectral coloration attributed to loudspeaker installation, crossover filtering, and delay/gain offsets. These filters can incorporate measurements taken at multiple listening points, allowing a more extensive listening area than filters derived from measurements taken at a single listening point. This work endeavors to update the existing equalization filter generation process by producing a new set of filters for various human subject testing scenarios.

Signal Processing↗
NASA NTRS1993

A new method for recognizing quadric surfaces from range data and its application to telerobotics and automation

The problem of recognizing and positioning of objects in three-dimensional space is important for robotics and navigation applications. In recent years, digital range data, also referred to as range images or depth maps, have been available for the analysis of three-dimensional objects owing to the development of several active range finding techniques. The distinct advantage of range images is the explicitness of the surface information available. Many industrial and navigational robotics tasks will be more easily accomplished if such explicit information can be efficiently interpreted. In this research, a new technique based on analytic geometry for the recognition and description of three-dimensional quadric surfaces from range images is presented. Beginning with the explicit representation of quadrics, a set of ten coefficients are determined for various three-dimensional surfaces. For each quadric surface, a unique set of two-dimensional curves which serve as a feature set is obtained from the various angles at which the object is intersected with a plane. Based on a discriminant method, each of the curves is classified as a parabola, circle, ellipse, hyperbola, or a line. Each quadric surface is shown to be uniquely characterized by a set of these two-dimensional curves, thus allowing discrimination from the others. Before the recognition process can be implemented, the range data have to undergo a set of pre-processing operations, thereby making it more presentable to classification algorithms. One such pre-processing step is to study the effect of median filtering on raw range images. Utilizing a variety of surface curvature techniques, reliable sets of image data that approximate the shape of a quadric surface are determined. Since the initial orientation of the surfaces is unknown, a new technique is developed wherein all the rotation parameters are determined and subsequently eliminated. This approach enables us to position the quadric surfaces in a desired coordinate system. Experiments were conducted on raw range images of spheres, cylinders, and cones. Experiments were also performed on simulated data for surfaces such as hyperboloids of one and two sheets, elliptical and hyperbolic paraboloids, elliptical and hyperbolic cylinders, ellipsoids and the quadric cones. Both the real and simulated data yielded excellent results. Our approach is found to be more accurate and computationally inexpensive as compared to traditional approaches, such as the three-dimensional discriminant approach which involves evaluation of the rank of a matrix. Finally, we have proposed one other new approach, which involves the formulation of a mapping between the explicit and implicit forms of representing quadric surfaces. This approach, when fully realized, will yield a three-dimensional discriminant, which will recognize quadric surfaces based upon their component surfaces patches. This approach is faster than prior approaches and at the same time is invariant to pose and orientation of the surfaces in three-dimensional space.

Alvertos, Nicolas↗
NASA NTRS1988

Empirical studies of design software: Implications for software engineering environments

The empirical studies team of MCC's Design Process Group conducted three studies in 1986-87 in order to gather data on professionals designing software systems in a range of situations. The first study (the Lift Experiment) used thinking aloud protocols in a controlled laboratory setting to study the cognitive processes of individual designers. The second study (the Object Server Project) involved the observation, videotaping, and data collection of a design team of a medium-sized development project over several months in order to study team dynamics. The third study (the Field Study) involved interviews with the personnel from 19 large development projects in the MCC shareholders in order to study how the process of design is affected by organizationl and project behavior. The focus of this report will be on key observations of design process (at several levels) and their implications for the design of environments.

Krasner, Herb↗
NASA NTRS1981

AVE-SESAME program for the REEDA System

The REEDA system software was modified and improved to process the AVE-SESAME severe storm data. A random access file system for the AVE storm data was designed, tested, and implemented. The AVE/SESAME software was modified to incorporate the random access file input and to interface with new graphics hardware/software now available on the REEDA system. Software was developed to graphically display the AVE/SESAME data in the convention normally used by severe storm researchers. Software was converted to AVE/SESAME software systems and interfaced with existing graphics hardware/software available on the REEDA System. Software documentation was provided for existing AVE/SESAME programs underlining functional flow charts and interacting questions. All AVE/SESAME data sets in random access format was processed to allow developed software to access the entire AVE/SESAME data base. The existing software was modified to allow for processing of different AVE/SESAME data set types including satellite surface and radar data.

Hickey, J. S.↗
NASA NTRS1972

Data processing at the University of Kansas

Two systems for processing remotely sensed image data have been discussed. The first system, IDECS, is a near real-time hardware system oriented towards processing multi-image data sets quickly and economically. The IDECS has convenient film input and color display output capabilities and implements simple kinds of decision rules. The second system, KANDIDATS, is a software system capable of performing many of the more sophisticated processing methods. Because of its monitor which handles all bookkeeping and its modular design, KANDIDATS easily allows the testing of new automatic processing techniques. After a new technique has been proven on KANDIDATS, it may be simplified and hard-wired in IDECS, thereby keeping the volume processing of remotely sensed data always up to the current state-of-the-art.

Haralick, R. M.↗
NASA NTRS1972

A simplified correlation technique for position location using earth satellites.

To derive range to a moving vehicle for surveillance and navigation purposes, the phase delays in sets of sinusoidal tones may be measured using synchronous satellites for signal relay. When the number of users is large, problems of rapid acquisition and measurement occur in multiple-access systems. This paper describes the selection and processing of an orthogonal tone set which has several useful features. The paper also presents a simulation of a simplified digital technique for the noise-free case, as well as for a composite signal buried in wideband noise. The digital simulation is also modified to include the proposed 'hard limiting' or clipping technique.

Martin, S. C.↗
NASA NTRS1988

The TAME Project: Towards improvement-oriented software environments

Experience from a dozen years of analyzing software engineering processes and products is summarized as a set of software engineering and measurement principles that argue for software engineering process models that integrate sound planning and analysis into the construction process. In the TAME (Tailoring A Measurement Environment) project at the University of Maryland, such an improvement-oriented software engineering process model was developed that uses the goal/question/metric paradigm to integrate the constructive and analytic aspects of software development. The model provides a mechanism for formalizing the characterization and planning tasks, controlling and improving projects based on quantitative analysis, learning in a deeper and more systematic way about the software process and product, and feeding the appropriate experience back into the current and future projects. The TAME system is an instantiation of the TAME software engineering process model as an ISEE (integrated software engineering environment). The first in a series of TAME system prototypes has been developed. An assessment of experience with this first limited prototype is presented including a reassessment of its initial architecture.

Basili, Victor R.↗
NASA NTRSDate not supplied

DLES Unreal Simulation Tool (DUST)

NASA’s future Artemis missions to the Moon seek to explore areas around the Lunar South Pole. Though humans have previously set foot on the lunar surface, the proposed region provides unique and challenging environments that require insight and investigation prior to arrival. Several teams throughout the agency are performing this site and mission planning, design, and analysis to support areas like the Human Landing System (HLS), surface mobility, habitation elements, and scientific exploration. The NASA Exploration Systems Simulation (NExSyS) team at Johnson Space Center is developing a graphical environment of the Lunar South Pole region. Lunar terrain information collected from the Lunar Reconnaissance Orbiter (LRO) is compiled and made available through Johnson Space Center’s Digital Lunar Exploration Sites (DLES) data sets. The DLES data is used to build this graphic environment. The process of ingesting and accurately modeling this information in a meaningful way for analysis creates its own challenges such as generating a performant model from the source data and the application of curvature. Additionally, the area around the Lunar South Pole experiences different lighting conditions than those observed from the Apollo missions. The need to use the lunar environmental data products provided by DLES combined with the capability to calculate date specific ephemerides in real-time has given rise to the development of the DLES Unreal Simulation Tool (DUST). DUST incorporates augmented terrain from the DLES product into a desktop application that allows exploration of the Lunar South Pole region and its complex lighting conditions. DUST leverages advanced capabilities in the recently released Unreal Engine 5 renderer by Epic Games such as double precision for positioning of planetary bodies and surface elements, multiple infinite light sources to represent the Sun and eventually Earthshine, high resolution shadow maps for dynamic shadow accuracy, real-time software ray-tracing for multi-surface bounce lighting to render sunlight reflected off surface elements and terrain features, and performance optimized level of detail shifting as the eyepoint changes in a scene. This paper details the DUST application, the technologies of the engine platform that enable scientific and engineering analysis, the unique techniques and processes developed to consume the DLES data sets, and how the tool is being used to support the Artemis program.

Lunar Visualization↗
NASA NTRSDate not supplied

XV-15 Tilt Rotor Research Aircraft Photogrammetry and Metrology Measurement

A new measurement capability was created by combining photogrammetry and metrology techniques to accurately measure one half of the XV-15 Tilt Rotor Research Aircraft at the Smithsonian’s Udvar-Hazy museum. The challenges imposed by the fuselage and surrounding environment at Udvar-Hazy were overcome by careful application of photogrammetry and metrology techniques. Data analyses and processing included the use of multiple reverse engineering programs to accurately generate a complete 3-dimensional water-tight geometry of the aircraft and rotor blade. This paper describes the photogrammetry and metrology measurement systems, technology and hardware set-up, data analysis and processing methods, future work, and lessons learned. In addition, selected measurement results of the fuselage and rotor blade are presented.

XV-15↗