Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

COS-B observations of localized sources of gamma-ray emission

In October 1975, the high-energy gamma-ray flux from the Vela pulsar measured by COS-B was found to be 1.6 to 2.1 times higher than the flux measured by SAS-2 in 1973. This factor is too large to be accounted for by error in the COS-B calibration or analysis. This is supported by a comparison of the COS-B measurement of the narrow-line component from the galactic center region with the flux derived from the measurements of SAS-2; the COS-B flux comes out about 15 percent lower than the SAS-2 figure. It is interesting to note that a glitch in the pulsar period took place about 1 month prior to the COS-B observation; the previous glitch occurred about 1.5 years before the SAS-2 observation. The increased rotational energy loss after the glitch cannot simply explain the increased gamma-ray luminosity. If the two phenomena are related, the gamma-ray emission, absorption, or beaming process must be extremely sensitive to changes in rotational parameters. The existence is confirmed of a second region of enhanced radiation in the galactic anticenter in addition to that from the Crab pulsar.

Source record↗
NASA NTRS1976

Particle and flow field measurements by laser holography

Holograms make transmission recordings of aerodynamic events which are real-illuminated with ground-glass light diffusers and with no requirements for precision. The three-dimensional interferograms can be recorded by stored-beam, double-exposure, and double-plate techniques. Weak traveling shock waves, generated by rotating blade rows of an aircraft fan compressor, can be visualized by rapid double-exposure holograms recorded with a ruby laser. The same laser technique can also determine flow velocities from holograms of small flow-entrained particles. Particles larger than one-quarter millimeter are recorded under rear diffuse illumination conditions. Smaller particles can be recorded by their own forward scattering of laser light through the sensitivity of the holographic process for weak signals. Since the holographic apparatus can be path-matched, both particle and flow interferograms can be recorded with lasers of short coherence length.

Wuerker, R. F.↗
NASA NTRS1981

Evaluation of moire techniques for wind tunnel metrology

The development of a moire technique suitable for the analysis of object deflections in a cryogenically cooled, transonic wind tunnel is described. The operating environment for the wind tunnel has a temperature range of 77 to 3390 k, pressure to 91390 Kgs/sq m, and noise to 150 dB SPL. Efforts were made to accomplish the following: to demonstrate projection moire as it would be used to study structural deflections; to use optical processing to multiply the sensitivity of the moire; and to investigate a system design based on the requirements of the wind tunnel geometry.

Harris, J. S.↗
NASA NTRS1982

Development of high strength, high temperature ceramics

Improvement in the high-pressure turbopumps, both fuel and oxidizer, in the Space Shuttle main engine were considered. The operation of these pumps is limited by temperature restrictions of the metallic components used in these pumps. Ceramic materials that retain strength at high temperatures and appear to be promising candidates for use as turbine blades and impellers are discussed. These high strength materials are sensitive to many related processing parameters such as impurities, sintering aids, reaction aids, particle size, processing temperature, and post thermal treatment. The specific objectives of the study were to: (1) identify and define the processing parameters that affect the properties of Si3N4 ceramic materials, (2) design and assembly equipment required for processing high strength ceramics, (3) design and assemble test apparatus for evaluating the high temperature properties of Si3N4, and (4) conduct a research program of manufacturing and evaluating Si3N4 materials as applicable to rocket engine applications.

Hall, W. B.↗
NASA NTRS1982

Influence of gravity driven convection on the directional solidification of Bi/MnBi eutectic composites

The role of gravity on Bridgman-Stockharger directional solidification of eutectic Bi/MnBi has been studied in reduced gravity aboard NASA sounding rocket SPAR flight experiments and contrasted with normal gravity investigations. The directional solidification of eutectic Bi/MnBi results in a low volume fraction, faceted/nonfaceted aligned rod eutectic whose MnBi rod size, interrod spacing, thermal and magnetic properties are sensitive functions of solidification processing conditions. The morphology of the low-gravity samples showed striking differences compared with identically processed, normal gravity samples grown in the same apparatus. The MnBi rod diameter and interrod spacing distributions were significantly smaller, approximately 50 percent, for the low gravity samples compared with identically processed one gravity samples. Accompanying the smaller MnBi rod diameters observed in the flight samples, was an increase in permanent magnet properties which reached greater than 97 percent of the theoretical maximum. Gravitationally induced thermal instabilities in one-gravity which result in irregular interface movement and associated difficulty of the faceted MnBi phase to branch are suggested to explain the morphological differences between one and low gravity solidification.

Pirich, R. G.↗
NASA NTRS1983

Spectroscopy of molecular oxygen in the atmospheres of Venus and Mars

The abundances of molecular oxygen in the atmospheres of Venus and Mars are sensitive to fundamental photochemical processes. A new upper limit is reported for the molecular oxygen mixing ratio (O2/CO2 less than 3 x 10 to the -7th) in the integrated column above the visible cloud tops of Venus, based on spectroscopic observations carried out in early spring, 1982. During the same observing period, an O2 column abundance of 8.5 cm-am for the atmosphere of Mars was measured, slightly below the O2 abundances measured a decade earlier.

Trauger, J. T.↗
NASA NTRS1984

Thermohaline circulation below the Ross Ice Shelf - A consequence of tidally induced vertical mixing and basal melting

The warmest water below parts of the Ross Ice Shelf resides in the lowest portion of the water column because of its high salinity. Vertical mixing caused by tidal stirring can thus induce ablation by lifting the warm but dense water into contact with the ice shelf. A numerical tidal simulation indicates that vertically well-mixed conditions predominate in the southeastern part of the sub-ice shelf cavity, where the water column thickness is small. Basal melting in this region is expected to be between 0.05 and 0.5 m/yr and will drive a thermohaline circulation having the following characteristics: high salinity shelf water (at - 1.8 C), formed by winter sea ice production in the open Ross Sea, flows along the seabed toward the tidal mixing fronts below the ice shelf; and meltwater (at -2.2 C), produced in the well-mixed region, flows out of the sub-ice shelf cavity along the ice shelf bottom. Sensitivity of this ablation process to climatic change is expected to be small because high salinity shelf water is constrained to have the sea surface freezing temperature.

Macayeal, D. R.↗
NASA NTRS1984

An operational system for subject switching between controlled vocabularies: A computational linguistics approach

The NASA Lexical Dictionary (NLD), a system that automatically translates input subject terms to those of NASA, was developed in four phases. Phase One provided Phrase Matching, a context sensitive word-matching process that matches input phrase words with any NASA Thesaurus posting (i.e., index) term or Use reference. Other Use references have been added to enable the matching of synonyms, variant spellings, and some words with the same root. Phase Two provided the capability of translating any individual DTIC term to one or more NASA terms having the same meaning. Phase Three provided NASA terms having equivalent concepts for two or more DTIC terms, i.e., coordinations of DTIC terms. Phase Four was concerned with indexer feedback and maintenance. Although the original NLD construction involved much manual data entry, ways were found to automate nearly all but the intellectual decision-making processes. In addition to finding improved ways to construct a lexical dictionary, applications for the NLD have been found and are being developed.

Silvester, J. P.↗
NASA NTRS1985

Using a life-cycle-cost criterion for multi-disciplinary design studies for the Manned Space Station

A life-cycle-cost measure for the Manned Space Station is suggested which considers the mass, initial cost, aerodynamic drag, electrical power, moment, required ground support, and expected life of subsystems or components. It is proposed that this life-cycle-cost measure be considered as a criterion for design trade-off studies involving controls and structures. Calculating the related sensitivities in the optimization process is discussed and then applied to specific examples. In the first example, the reaction control system is analyzed with regard to the design of its supporting structure and selection of rocket type. Values of support beam length, structural material selection, and rocket propellant selection are determined which minimize life-cycle-cost. In the second example, the alignment of solar arrays are analyzed for efficiency with regard to generating power, their drag, and their aerodynamic moment. Alignment angles are determined which again minimize life cycle cost. It seems clear from these and other examples that the proposed criterion has value for multi-disciplinary design studies for the Manned Space Station.

Taylor, L. W.↗
NASA NTRS1985

Dynamic verification of very large space structures

The dynamic verification of spacecraft relies heavily on ground-based tests. These tests usually simulate flight environments or validate analytical models used in establishing design loads and in designing control algorithms. They also provide security against failures resulting from unanticipated or unmodeled hardware behavior. Future orbital antennas, space stations, and solar power systems are likely to be of sizes difficult to test using current ground test technology. In addition to size, other factors such as low natural frequencies, lightweight construction, and the presence of many structural joints, cause significant sensitivity of the test process to the earth-gravity environment. Yet, accuracy requirements on the verification process will be more stringent because of modern flexible-structure control approaches. This paper describes some of the problems and discusses research on potential solutions. The importance of an integrated ground test, analysis, and flight test program is emphasized. An ongoing research program of this type focusing on a 60-meter, deployable, truss-beam test article is described.

Hanks, B. R.↗
NASA NTRS1989

Design sensitivity analysis of boundary element substructures

The ability to reduce or condense a three-dimensional model exactly, and then iterate on this reduced size model representing the parts of the design that are allowed to change in an optimization loop is discussed. The discussion presents the results obtained from an ongoing research effort to exploit the concept of substructuring within the structural shape optimization context using a Boundary Element Analysis (BEA) formulation. The first part contains a formulation for the exact condensation of portions of the overall boundary element model designated as substructures. The use of reduced boundary element models in shape optimization requires that structural sensitivity analysis can be performed. A reduced sensitivity analysis formulation is then presented that allows for the calculation of structural response sensitivities of both the substructured (reduced) and unsubstructured parts of the model. It is shown that this approach produces significant computational economy in the design sensitivity analysis and reanalysis process by facilitating the block triangular factorization and forward reduction and backward substitution of smaller matrices. The implementatior of this formulation is discussed and timings and accuracies of representative test cases presented.

Kane, James H.↗
NASA NTRS1989

Force/torque and tactile sensors for sensor-based manipulator control

The autonomy of manipulators, in space and in industrial environments, can be dramatically enhanced by the use of force/torque and tactile sensors. The development and future use of a six-component force/torque sensor for the Hermes Robot Arm (HERA) Basic End-Effector (BEE) is discussed. Then a multifunctional gripper system based on tactile sensors is described. The basic transducing element of the sensor is a sheet of pressure-sensitive polymer. Tactile image processing algorithms for slip detection, object position estimation, and object recognition are described.

Vanbrussel, H.↗
NASA NTRS1989

An improved architecture for video rate image transformations

Geometric image transformations are of interest to pattern recognition algorithms for their use in simplifying some aspects of the pattern recognition process. Examples include reducing sensitivity to rotation, scale, and perspective of the object being recognized. The NASA Programmable Remapper can perform a wide variety of geometric transforms at full video rate. An architecture is proposed that extends its abilities and alleviates many of the first version's shortcomings. The need for the improvements are discussed in the context of the initial Programmable Remapper and the benefits and limitations it has delivered. The implementation and capabilities of the proposed architecture are discussed.

Fisher, Timothy E.↗
NASA NTRS1991

Laser interferometric measurement of ion electrode shape and charge exchange erosion

A projected fringe profilometry system was applied to surface contour measurements of an accelerator electrode from an ion thrustor. The system permitted noncontact, nondestructive evaluation of the fine and gross structure of the electrode. A 3-D surface map of a dished electrode was generated without altering the electrode surface. The same system was used to examine charge exchange erosion pits near the periphery of the electrode to determine the depth, location, and volume of material lost. This electro-optical measurement system allowed rapid, nondestructive, digital data acquisition coupled with automated computer data processing. In addition, variable sensitivity allowed both coarse and fine measurements of objects having various surface finishes.

Macrae, Gregory S.↗
NASA NTRS1991

Reconnection voltage as a function of IMF clock angle

Magnetic reconnection between the IMF and the geomagnetic field is thought to play a major role in the transfer of solar wind momentum and energy to the magnetosphere. Both analytic modeling and analysis of geophysical data have shown that this coupling process should be a sensitive function of the clock angle of the IMF. Results are presented from a three-dimensional, MHD, global numerical simulation code for the reconnection voltage between the closed geomagnetic field and the IMF as a function of the IMF clock angle. These results are consistent with a sin(theta/2) functional behavior.

Fedder, J. A.↗
NASA NTRS1991

Laser interferometric measurement of ion electrode shape and charge exchange erosion

A novel projected fringe profilometry system was applied to surface contour measurements of an accelerator electrode from an ion thruster. The system permitted noncontact, nondestructive evaluation of the fine and gross structure of the electrode. A 3D surface map of a dished electrode was generated without altering the electrode surface. The same system was used to examine charge exchange erosion pits near the periphery of the electrode to determine the depth, location, and volume of material lost. This electro-optical measurement system allowed rapid nondestructive digital data acquisition coupled with automated computer data-processing. In addition, variable sensitivity allowed both coarse and fine measurements of objects having various surface finishes.

Macrae, Gregory S.↗
NASA NTRS1992

Embryogenesis and organogenesis of Carausius morosus under space flight conditions (7-IML-1)

The experiment is part of a radiobiological space research program to obtain experimental data on the biological effectiveness of the structured component of cosmic radiation during spaceflight. In this proposed experiment, Carausius morosus embryos of different ages will develop under spaceflight conditions. The experiment is designed to determine the influence of galactic heavy ions of very high energy deposition in microgravity on developmental processes of different radiation sensitivity and regenerative capacity. Layers of Carausius morosus eggs are sandwiched between different track detectors (cellulose nitrate, CR39). This method allows the localization of the trajectory of each heavy ion in the biological layer and the identification of the site of the penetration inside the egg.

Buecker, D. H.↗
NASA NTRS1991

Impact of diet on the design of waste processors in CELSS

The preliminary results of a design analysis for a waste processor which employs existing technologies and takes into account the constraints of human diet are presented. The impact of diet is determined by using a model and an algorithm developed for the control and management of diet in a Controlled Ecological Life Support System (CELSS). A material and energy balance model for thermal oxidation of waste is developed which is consistent with both physical/chemical methods of incineration and supercritical water oxidation. The two models yield quantitative analysis of the diet and waste streams and the specific design parameters for waste processors, respectively. The results demonstrate that existing technologies can meet the demands of waste processing, but the choice and design of the processors or processing methods will be sensitive to the constraints of diet. The numerical examples are chosen to display the nature and extent of the gap in the available experiment information about CELSS requirements.

Waleh, Ahmad↗