SEARCH · Engineering Papers

Results for “PELLETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Evaluation of a Smoke Opacity Sensor for Improving Residential Wood Heater Combustion

Residential wood heating lacks real-time particulate matter (PM) monitoring technologies capable of measuring emissions directly from flue gases. This study evaluates the performance of the Octoring, an opacity-based smoke sensor developed to monitor wood heater emissions and provide feedback for improved combustion. The device was tested on catalytic and non-catalytic cordwood heaters and a pellet heater during startup, high-burn, and low-burn phases. Performance was assessed against reference particle instruments and gravimetric measurements using concordance, correlation, and agreement analyses. Results show that temperature-dependent drift is the primary limitation affecting sensor accuracy, with systematic drift observed across ambient and combustion conditions. Agreement with reference instruments ranged from poor to good depending on operating conditions, with the strongest performance observed during pellet heater high-burn operation. These findings establish a performance baseline for opacity-based sensing technologies and identify key areas for further development before practical deployment in residential wood combustion monitoring systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Uranium Nitride as LWR TRISO Fuel: Thermodynamic Modeling of U-C-N and Thermomechanics

A new concept for light water reactor (LWR) nuclear fuel has recently been proposed that utilizes pellets of tristructural isotropic (TRISO) fuel particles embedded in a SiC or zirconium alloy matrix, replacing sintered urania pellets. The fuel is considered significantly more accident tolerant than urania as the SiC matrix or coated/protected zirconium alloy and TRISO particles would be highly resistant to oxidation and fission product release under beyond-design-basis accident conditions. As is well understood, failed fuel rods release gaseous and volatile fission products, and that is greatly exacerbated as urania oxidizes from UO 2+x to higher oxidations states in failed fuel pin with resulting expansion, loss of integrity, and significant further release of fission products.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

Particle size of several plutonium-238 oxide fuel samples from oxalate precipitation processes

Particle size of 238 PuO 2 powders is an important factor in determining the structural integrity of fuel pellets hot-pressed from the oxide powder. Understanding the evolution of particle size during aqueous processing is a first step in assuring control of particle size throughout the pellet formation process. Measured particle sizes are reported here, and discussed in terms of measured particle size changes occurring during calcining, observed aggregation of particulate, and particle morphology. Morphology and aggregation are related to surface energy, which governs granule formation and hot pressing behavior. Results are discussed in terms of reported dependence of oxide morphology on process temperatures and reagent concentrations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Distended clads gas pressurization and material failure timescales

This document presents timescales for additional failure modes, including pressurization of void space in the pellet to the estimated tensile strength of the pellet. Because helium is known to be captured in the fuel as well as evolved as gas, previous timescales are adjusted to account for the substantial dissolution of helium in the matrix of the fuel at normal fuel temperatures. Helium arises from the decay of the 238Pu in the fuel, and can appear as a gas, creating bubbles within the fuel. The majority of helium is known to be captured within the fuel matrix at the operating temperatures of an isolated clad.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Experimental and Simulation Analysis of Binary Mixtures of Biomass and Inert Material

A literature review was conducted to identify experiments on various scales of biomass combustion specific to circulating fluidized bed (CFB) combustors. Typical feedstock and inert bed material characteristics for biomass combustion in a CFB were gathered. This information was used to design laboratory-scale, non-reacting experiments on biomass-inert bed material mixtures in a 1-in. cylindrical test rig in the Multiphase Flow Analysis Laboratory (MFAL) in Morgantown, WV. The biomass chosen was a hardwood. Pellets from the hardwood were milled and sieved to obtain three size ranges—small, medium, and large. Three mass loadings of each of the biomass samples were fluidized with glass beads as the inert bed material to study the mixing characteristics under varying fluidizing gas velocities. Hydrodynamic data including pressure drop measurements at select vertical locations and video recordings of the mixture behavior were generated in this effort.

09 BIOMASS FUELS↗

DOE OSTI2020

Sample Preparation for 3D Characterization of Irradiated Fuel

Thorough characterization of nuclear fuel is essential when striving to understand its microstructural evolution in response to varying irradiation conditions. A detailed understanding of the microstructural evolution of irradiated fuel can be useful when predicting the fuel’s response to off-normal conditions and related phenomena such as high burnup fuel fragmentation (HBFF) and fission gas release. This sort of characterization and the study of complex phenomena like HBFF that are related to fuel performance are an important part of the US Department of Energy Office of Nuclear Energy’s Advanced Fuels Campaign (AFC). Multiple characterization techniques are commonly used to perform post-irradiation examination (PIE) analysis on an irradiated fuel sample, but many of these techniques are limited to the 2D surface analysis of the fuel pellet. Although there is a lot of useful information to be gained by analyzing the fuel pellet surface, a 2D analysis provides only an approximation of the nature of the material’s features, such as porosity and grain structure. Therefore, it is critical to analyze the 3D structure of the material, as materials exist and respond to conditions in all three dimensions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Plane-Strain Tension Testing of ATF FeCrAl Cladding (Progress Report)

Performance of advanced accident-tolerant fuel (ATF) claddings must be assessed under all relevant scenarios, including normal and off-normal operating conditions, as well as during a reactivity-initiated accident (RIA). During RIA, the fuel pellet may expand and cause significant loads on cladding, a condition known as pellet cladding mechanical interaction (PCMI), which may even lead to cladding failure. This report describes the fiscal year (FY) 2020 research activities and results from the development of separate-effects testing for ATF cladding candidate iron-chromium-aluminum (FeCrAl) tube specimens under loading conditions expected during RIA/PCMI events. To assess material performance under PCMI, a high strain rate burst test, often termed the modified burst test (MBT), is commonly employed. However, execution of such a test in a hot cell requires significant research. To overcome the complexities of performing MBTs in a hot-cell environment on irradiated samples, a plane-strain tension (PST) test was proposed by several authors as an alternative approach for PCMI testing. A new fixture was developed so that PST specimens could be tested using a more accommodating design for hot-cell manipulators. This report presents the PST fixture design, evaluates the possibility of modifying the specimen geometry, and discusses experimental results with unirradiated Al 6061 and FeCrAl tubes at various lengths. Furthermore, this report discusses the relevance and compatibility of the PST results to RIA scenarios and compares the PST and MBT results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Pitch Variation Experiments in Water-Moderated Square-Pitched U(6.90)O 2 Fuel Rod Lattices with Fuel to Water Volume Ratios Spanning 0.08 to 0.67

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Updated Estimate of Tritium Permeation from TPBAR Disposal Containers in ILV (U)

A tritium source term analysis was performed for TPBAR disposal in the E-Area Intermediate Level Vaults for the E-Area Low-Level Waste Facility Performance Assessment (PA). This analysis is based on an earlier source term analysis which treated the bulk oft he tritium residual as tightly bound by the TPBAR getter material, with only a small fraction existing as tritiated moisture in the lithium aluminate ceramic pellets. Together with atmospheric moisture trapped in the free volume, the tritiated water vapor is assumed to corrode steel surfaces inside the disposal container, covering them with a magnetite film while generating hydrogen. The carbon steel walls of the disposal container are permeable to hydrogen, providing a path way for tritium to escape containment. The rate of hydrogen generation is assumed to be limited by the rate of corrosion, which is assumed to be governed by parabolic reaction kinetics obtained from the literature. This relies on the further assumption that the water vapor consumed by the corrosion reaction is continually replaced by moisture from the lithium aluminate pellets until all of that moisture is gone. In addition to tritium permeation, the analysis also includes a slow leak through the disposal container walls at the maximum allowable leak rate, 1 x 1CH standard cm3/s. Results were obtained for four different combinations of internal and container wall temperatures, established in an earlier thermal analysis that considered two different vault loadings and two different TPBAR activity levels. Instantaneous release rates for these four cases are plotted in Figure ES-1 below

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

2022 Accomplishments Report Template

Chromium-doped UO 2 fuels is an industrially important Accident Tolerant Fuel (ATF) due to the ability to increase the average grain size relative to standard UO 2 . However, there is a lack of knowledge of the thermophysical properties of these doped fuels, which is necessary for accurately modeling the in-pile performance. The work accomplished this FY focused on developing large grain Cr-doped UO 2 pellets as a function of Cr content and subsequently measuring the thermophysical and mechanical properties. The microstructural variations were also investigated to evaluate chromium formation within the microstructure of the sintered pellets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

First Principles Modeling of Tritium Trapping in γ-LiAlO 2 Nanovoids

Experimental STEM and APT investigations both indicate the presence of nanovoids in γ-LiAlO 2 pellets. While those nanovoids can affect the diffusion of tritium in pellets, first principles simulations have been conducted to evaluate the potential for tritium trapping by single and double cation and anion vacancies. It was found that tritium trapping allows to recover a significant amount of the formation energy cost of cation vacancy, while the trapping of tritium by anion vacancies further increase the energy cost of forming a vacancy. The simulations also indicated the potential for tritium to be trapped in various forms by forming bonds such as Al—T, O—T or T 2 . These results raise further questions regarding the speciation and dynamics of tritium trapped in nanovoids.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2023

Determining the 193 m Ir/ 192 Ir ratio from high-resolution X-ray measurements

Two pellets of iridium salt were irradiated at the center of the Flattop critical assembly, one at low neutron flux and the other at high flux. After that two counting samples were prepared from each pellet following a given chemical procedure. Measurements of the four counting samples were carried out with two high-resolution silicon drift detectors for over a year. Pulse height spectra of the L→M X-rays from 193 m Ir and 192 Ir were approximated with a Voigt function and the ratio of produced 193 m Ir and 192 Ir nuclei obtained. The 193 m Ir/ 192 Ir ratios from each measured spectrum are compared to identify possible systematic deviations.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2023

Tech-X contributions to the Center for Tokamak Transients (CTTS) Scientific Discovery through Advanced Computing (SciDAC) project (Final Report)

The Center for Tokamak Transients Simulations (CTTS) consists of computational plasma physicists, computer scientists, and applied mathematicians who are together developing and applying simulation software to improve our understanding of and ability to predict and control transient events in tokamak discharges, particularly those that lead to violent disruptions. We have major simulation activities concerning disruptions that are caused by violating ideal MHD stability criteria, vertical displacement events, resistive wall modes, and tearing modes. We are performing comprehensive modeling of disruption mitigation techniques, particularly by shattered pellet injection (SPI). The Center is built around two mature extended MHD codes: NIMROD and M3D-C1. These codes are being extended in a number of ways as required by the demands of disruption modeling, and are being optimized to work well for larger problem size and modern computer architectures as required to model tokamak plasmas with realistic parameters over the required timescales. The codes will be coupled to the FronTier code for state-of-the-art modeling of SPI. Validation with experimental data on DIII-D, NSTX, and JET is being facilitated by rigorous uncertainty quantification (UQ). The high-level objectives of the center are to: (1) Develop better understanding and improved predictive capability of when crossing a linear stability boundary will likely lead to a disruption, (2) Provide a tool for calculating vessel forces, both axisymmetric and non-axisymmetric, for worst case VDE and other disruptions in tokamaks, (3) Develop increased understanding and improved predictive capability for locked mode disruptions and how best to avoid them, (4) Develop, verify, and validate 3D models for disruption mitigation by shattered pellets that can be used to design and optimize a system for future tokamaks, and (5) Increase the efficiency and scalability of the M3D-C1 and NIMROD codes so that they can model disruptions in ITER scale devices using the most powerful DOE HPC hardware, and (6) Demonstrate code-coupling via FronTier coupling with NIMROD and M3D-C1 and by interfacing these codes within a WDM framework.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Development of bubble evolution model for new mechanistic transient fission gas release capability in BISON

This report summarizes efforts within NEAMS to investigate the mechanisms that govern fission gas behavior in UO 2 . In particular, the focus is on understanding how fission gas behavior causes transient fission gas release and fragmentation/pulverization of high burnup structure (HBS) in UO 2 . HBS forms in the periphery of the pellet where temperatures are relatively low. Previously, MD simulations were performed to determine the reaction energies for various Xe and U defects with bubbles, as a function of Xe to vacancy ratio or, equivalently, pressure. As had been shown in FY22, it was found that the unmodified version of the Simple Integrated Fission Gas Release and Swelling (SIFGRS) model within BISON greatly over-predicted the number gas atoms per vacancy in the bubbles in the outer rim of the pellet (a ratio of > 1 million). This was due to slow grain boundary vacancy diffusivity and not accounting for the pressure-dependent reaction energy for Xe interstitials with bubbles. The application of the pressure dependent reaction energies was able to restrict Xe to vacancy ratios to 2:1, which is far more realistic than those originally obtained from SIFGRS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

THOR-aLEU Report

The advanced low enriched uranium (aLEU)-THOR experiment vehicle is designed to irradiate fresh fuel rodlet specimens containing UO 2 (uranium dioxide) in the Temperature Heat-sink Overpower Response (THOR) capsule. The goal of the experiments are to compare the behaviors of standard UO 2 pellets to an aLEU concept in which molybdenum (Mo) foils separate UO 2 wafers increasing the thermal conductivity of the fuel. This experiment is designed to be conducted in the Transient Reactor Test facility (TREAT) using the Minimal Activation Retrievable Capsule Holder (MARCH) irradiation system. The goal of these experiments is to assess the effect of thermally conductive inserts in UO 2 by measuring their net effect on radial thermal conductivity using transient nuclear heating and then to determine their power-to-melt threshold in transient overpower ramps. The objective of the aLEU-THOR fuels experiment is to determine the viability and study the performance of UO 2 fuel pellets employing newly upgraded TREAT capability. A novel transient measurement technique will be used with the THOR capsule, which has a solid heat sink to generate the transient temperature gradient for conductivity measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Performance Testing of Moving Bed Gasifier Using Biomass and Waste Fuels to Generate Low-Cost Clean Hydrogen

Our need for hydrogen is growing as the world transitions toward a low-carbon future. Hydrogen provides long-term energy storage for grid stability in a solar- and wind-dominated power market and can be used to decarbonize other sectors. One promising process for generating low-cost hydrogen that produces net-negative carbon is to gasify biomass with a mixture of legacy coal wastes, waste plastics, and other wastes with carbon capture. Use of waste fuels lowers costs and diverts waste from landfills. EPRI is leading a project, funded by the U.S. Department of Energy, to conduct performance testing of modular, moving-bed gasification for the generation of low-cost, clean hydrogen from biomass mixed with legacy coal waste, waste plastic, and/or refuse derived fuels. The work scope includes preparation of multiple pellet feedstocks using biomass (both woody biomass and corn stover) with a mixture of legacy coal waste, plastic waste (wire insulation), and refuse-derived fuel (RDF). These pelletized feedstocks are being qualified based on performance testing of selected fuel blend compositions in updraft moving-bed gasifier located in Sardinia, Italy. Testing is being conducted to obtain relevant data to advance the modular design of the moving-bed gasification process, and successfully use these feedstocks to produce a high hydrogen content raw syngas that can be shifted to produce clean hydrogen. Testing results will be used to determine the effects of the various fuels on feedstock development, the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics), and impacts on gasifier operations.

08 HYDROGEN↗

DOE OSTI2023

Molybdenum Sleeve Experiments in Fully-Reflected Water-Moderated Triangular-Pitched U(6.90)O 2 Fuel Rod Lattices (1.55 cm Pitch)

The US Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories. The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5 % 235 U. The 7uPCX assembly is a water-moderated and -reflected array of aluminum-clad U(6.90 %)O 2 fuel rods. Other critical experiments performed in the 7uPCX assembly are documented in LEU-COMP-THERM-078, LEU-COMP-THERM-080, LEU-COMP-THERM-096, LEUCOMP-THERM-097, LEU-COMP-THERM-101, and LEU-COMP-THERM-102. The purpose of these experiments was to measure the effects of molybdenum in nearly-critical systems. The molybdenum was introduced into the fuel arrays as tubular sleeves that surrounded some of the fuel rods in the fuel arrays measured. Four hundred molybdenum tubes nominally 12.7 mm outside diameter, 498 mm long, with 0.762 mm wall thickness were provided for the experiments by the Institut de Radioprotection et de Sûreté Nucléaire (IRSN). Small polyethylene adapters at each end of the tubes were used to center each tube on a fuel rod in the assembly. The critical experiments were done using a set of triangular-pitched grid plates fabricated for these experiments. The grid plate set accommodated a fuel array of a total of 1261 fuel rod positions on a pitch of 0.610 in (1.5494 cm) in a series of 20 hexagonal rings surrounding the central fuel rod. The fuel used in these experiments was fabricated using unirradiated 6.90 % enriched UO 2 fuel pellets from fuel elements designed to be used in the internal nuclear superheater section of the Pathfinder boiling water reactor operated in South Dakota by the Northern States Power Company in the 1960s. The fuel elements were obtained from The Pennsylvania State University where they had been stored for many years. The fuel pellets in those fuel elements were removed from the original Incoloy cladding and reclad in 3003 aluminum tubes and end caps for use in the experiments reported here. The five critical experiments in this series were performed in August through December 2022, in the Sandia Critical Experiments (SCX) at the Sandia Pulsed Reactor Facility. Case 1 had no molybdenum sleeves, Case 2 had 208 molybdenum sleeves clustered at the center of the array, Case 3 had 397 molybdenum sleeves clustered at the center of the array, Case 4 had 175 molybdenum sleeves in the central position and in five alternating hexagonal rings, and Case 5 had 331 molybdenum sleeves in the central position and in seven alternating hexagonal rings. All five critical experiments are judged to be acceptable as benchmark experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Sister Rod Destructive Examinations (FY23): Appendix J: Leaching of High Burnup Used Nuclear Fuel in Deionized Water

The leaching experiment aims to understand the trends in the radiolysis-enhanced dissolution of HBU SNF when exposed to water (e.g., in-reactor or in-pool cladding failures). Specimens from a baseline M5-clad rod and a heat-treated M5 rod were cut from the fractured CIRFT specimens and placed in 100 mL deionized water for a period of 128 days. Both radial and axial sections were cut to provide different surface areas of fuel in contact with the leachate. During the four-month exposure period, aliquot samples of the leachate were analyzed using gamma spectroscopy and inductively coupled plasma - mass spectrometry (ICP-MS). The analysis quantified the amount of fuel leached into the solutions and provided individual isotopic release fractions (of 30+ isotopes) which were compared as a function of time and surface area of the fuel exposed. Consistent with existing literature, the leaching followed a trend in which isotopes of certain elements such as Cs and Mo were among the first species in the matrix to dissolve, and with the highest release rates. This was followed by a gradual matrix dissolution consisting of uranium and other actinides and a slower-than-matrix release from some isotopes, including Ru and Rh. It was also observed that the circumferential samples having less exposed fuel surface area (to begin with) leached more than the axial samples for a majority of the isotopes during the timespan of the study. Previous experiments were conducted by decladding or exposing the pellet-clad surface completely, but the samples used in this study retained the cladding. One possible explanation for the higher leaching rate of the circumferential samples is that the pellet-clad interface, which has a greater density of grain boundaries and defects, may be the most vulnerable area to leaching of fuel in the presence of water.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗