Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Milling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Magnetic and mechanical properties of grain-refined Dy-free Nd-Fe-B sintered magnets

In this work, the effects of grain size on magnetic and mechanical properties of Dy-free Nd-Fe-B sintered magnets were studied. The grain size of the sintered magnets was varied by using different sized Dy-free Nd-Fe-B alloy feedstock powders which were ball milled to different extents. Increasing the ball milling time from 7 to 11 h caused the average particle size of the powders to decrease from 3.6 to 2.1 µm, while the average grain size of the corresponding sintered magnets decreased from 5.0 to 4.0 µm. The intrinsic coercivity Hcj and maximum energy product (BH) max of these magnets increased from 11.6 to 13.7 kOe and 41.6 to 43.6 MGOe, respectively. The finer grain magnets exhibited better thermal stability, as indicated by a smaller temperature coefficient of H cj (-0.71%/°C). With extending ball milling time to 15 h, the magnetic properties of the magnets deteriorate, while the flexural strengths first decrease and then increase. The flexural strength improvement is attributed to the increased Oxygen content in the magnets due to finer grains. The coercivity enhancement by reduction of grain size is a promising approach to develop Dy-free Nd-Fe-B sintered magnets with better thermal stability. It is important to control the Oxygen contents in the magnets to compromise both magnetic and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis and properties of bulk cobalt-carbide permanent magnets

Nanocrystalline bulk Co-C permanent magnets were produced by rapid hot consolidation of ball milled powder precursors. Bulk magnets with an average grain size of 20 nm and densities up to 94 percent of the theoretical density were successfully processed at pressures exceeding 1 GPa for the first time. Their microstructural and magnetic properties along with their magnetocrystalline anisotropy values are reported. Presence of iron contamination that results from the use steel milling media in milling was confirmed by elemental mapping of the bulk magnets. It is concluded that iron bonds in the form of hematite and does not adversely affect coercivity values. Here, this study shows that the Co 3 C compound does possess a sizable magnetocrystalline anisotropy, making it a suitable candidate as a rare earth free permanent magnet.

Co3 C↗
DOE OSTI2021

Non-perturbative BRST symmetry and the spectral structure of the ghost propagator

In BRST-quantised Yang-Mills theory the existence of BRST symmetry imposes significant constraints on the analytic structure of the continuum theory. In particular, the presence of this symmetry in the non-perturbative regime implies that any on-shell state with vanishing norm must have an associated partner state with identical mass, but negative inner product. In this work we demonstrate that for quantum chromodynamics (QCD) this constraint gives rise to an interconnection between the ghost and gluon spectra, and in doing so provides a non-trivial test of whether BRST symmetry is realised non-perturbatively. By analysing infrared lattice data for the minimal Landau gauge ghost propagator in pure SU(3) Yang-Mills theory, and comparing this with previous results for the gluon propagator, we show that this interconnection is violated, and hence conclude that continuum and current lattice formulations of Yang-Mills theory in Landau gauge represent two distinct realisations of the theory.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Thermal Evolution of Internal Strain in Doped PbTe

Recent improvements in the efficiency of heat-to-electricity energy conversion in lead chalcogenide thermoelectrics involve reducing the thermal conductivity by incorporating large amounts of internal strain. The extent to which typical lead chalcogenide processing techniques (such as doping, ball milling, and densification) increase internal strain and dislocation density must be quantified to improve materials design. In this study, neutron powder diffraction is leveraged to evaluate the internal strain introduced by ball milling in doped and undoped powders. Doping with Na and/or Eu increases internal strain beyond ball milling alone, with the greatest increase from combining the two dopants. Strain recovery occurs in each powder above 400 K but can be suppressed by co-doping, indicating a strong dopant–dislocation interaction in this system. Therefore, high-temperature processing of PbTe powders should be avoided if high internal strain is desired. Low-temperature densification and/or rapid pressing techniques may be key to maintaining internal strain in the final pressed pellet. The diffraction peak asymmetry and correlated elastic softening measured in pressed PbTe pellets in past studies were not observed in the precursor powders measured here, suggesting that measurements of the Debye temperature on final pressed pellets are required to examine the influence of defect-induced elastic softening on thermal conductivity. This work provides key guidance for defect engineering to maximize internal strain and thermoelectric performance in PbTe thermoelectrics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Direct Mechanochemical Synthesis, Phase Stability, and Electrochemical Performance of α-NaFeO 2

To better understand polymorph control in transition metal oxides, the mechanochemical synthesis of NaFeO 2 was explored. In this paper, we report the direct synthesis of α-NaFeO 2 through a mechanochemical process. By milling Na 2 O 2 and γ-Fe 2 O 3 for 5 h, α-NaFeO 2 was prepared without high-temperature annealing needed in other synthesis methods. While investigating the mechanochemical synthesis, it was observed that changing the starting precursors and mass of precursors affects the resulting NaFeO 2 structure. Density functional theory calculations on the phase stability of NaFeO 2 phases show that the α phase is stabilized over the β phase in oxidizing environments, which is provided by the oxygen-rich reaction between Na 2 O 2 and Fe 2 O 3 . This provides a possible route to understanding polymorph control in NaFeO 2 . Annealing the as-milled α-NaFeO 2 at 700 °C has resulted in increased crystallinity and structural changes that improved electrochemical performance in terms of capacity over the as-milled sample.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Functionalized Silicon Particles for Enhanced Half- and Full-Cell Cycling of Si-Based Li-Ion Batteries

Vinylene carbonate (VC) and polyethylene oxide (PEO) have been investigated as functional agents that mimic the solid electrolyte interphase (SEI) chemistry of silicon (Si). VC and PEO are known to contribute to the stability of Si-based lithium-ion batteries as an electrolyte additive and as a SEI component, respectively. In this work, covalent surface functionalization was achieved via a facile route, which involves ball-milling the Si particles with sacrificial VC and PEO. Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy indicate that the additives are strongly bound to Si. In particular, MAS NMR shows Si–R or Si–O–R groups, which confirm functionalization of the Si after milling in VC or PEO. Particle size analysis by dynamic light scattering reveals that the additives facilitate particle size reduction and that the functionalized particles result in more stable dispersions based on zeta potential measurements. Raman mapping of the electrodes fabricated from the VC and PEO-coated active material with a polyacrylic acid (PAA) binder reveals a more homogenous distribution of Si and the carbon conductive additive compared to the electrodes prepared from the neat Si. Furthermore, the VC-milled Si strikingly exhibited the highest capacity in both half- and full-cell configurations, with more than 200 mAh g –1 measured capacity compared to the neat Si in the half-cell format. This is linked to an improved electrode processing based on the Raman and zeta potential measurements as well as a thinner SEI (with more organic components for the functionalized Si relative to the neat Si) based on XPS analysis of the cycled electrodes. In conclusion, the effect of binder was also investigated by comparing PAA with P84 (polyimide type), where an increased capacity is observed in the latter case.

25 ENERGY STORAGE↗
DOE OSTI2024

Bayesian stability and force modeling for uncertain machining processes

Accurately simulating machining operations requires knowledge of the cutting force model and system frequency response. However, this data is collected using specialized instruments in an ex-situ manner. Bayesian statistical methods instead learn the system parameters using cutting test data, but to date, these approaches have only considered milling stability. This paper presents a physics-based Bayesian framework which incorporates both spindle power and milling stability. Initial probabilistic descriptions of the system parameters are propagated through a set of physics functions to form probabilistic predictions about the milling process. The system parameters are then updated using automatically selected cutting tests to reduce parameter uncertainty and identify more productive cutting conditions, where spindle power measurements are used to learn the cutting force model. The framework is demonstrated through both numerical and experimental case studies. Results show that the approach accurately identifies both the system natural frequency and cutting force model.

42 ENGINEERING↗
DOE OSTI2025

Mechanochemical α to β phase transition of U 3 O 8

Recognized as the most stable phase of uranium oxide, α-U 3 O 8 is widely used throughout the nuclear fuel cycle for safe storage and transportation. There is, however, a lack of understanding of the thermodynamic relationship between α-U 3 O 8 and its polymorph, β-U 3 O 8 . This research contributes new knowledge regarding the kinetics and mechanism of a previously described mechanochemical phase transition between the α- and β-U 3 O 8 polymorphs to improve the understanding of their thermodynamic relationship. In this work, tumble milling of α-U 3 O 8 using different milling media shows an ingrowth of the β-phase over time, with an observed correlation between media density, percent conversion and lattice strain. Anisotropic peak broadening observed within collected X-ray diffraction powder patterns suggests the preservation of uranium polyhedral layered sheets throughout the milling process. Preservation of the sheets implies a shear-induced slip mechanism occurring through in-plane shifting of uranium polyhedra along lattice planes perpendicular to the polyhedral sheets.

Roach, Jordan M. [Oak Ridge National Laboratory (O↗
DOE OSTI2024

Effect of fabrication processes on BaTiO 3 capacitor properties

There is an increasing desire to utilize complex functional electronic materials such as ferroelectrics in next-generation microelectronics. As new materials are considered or introduced in this capacity, an understanding of how we can process these materials into those devices must be developed. Here, the effect of different fabrication processes on the ferroelectric and related properties of prototypical metal oxide (SrRuO 3 )/ferroelectric (BaTiO 3 )/metal oxide (SrRuO 3 ) heterostructures is explored. Two different types of etching processes are studied, namely, wet etching of the top SrRuO 3 using a NaIO 4 solution and dry etching using an Ar + -ion beam (i.e., ion milling). Polarization-electric-field hysteresis loops for capacitors produced using both methods are compared. For the ion-milling process, it is found that the Ar + beam can introduce defects into the SrRuO 3 /BaTiO 3 /SrRuO 3 devices and that the milling depth strongly influences the defect level and can induce a voltage imprint on the function. Realizing that such processing approaches may be necessary, work is performed to ameliorate the imprint of the hysteresis loops via ex situ “healing” of the process-induced defects by annealing the ferroelectric material in a barium-and-oxygen-rich environment via a chemical-vapor-deposition-style process. This work provides a pathway for the nanoscale fabrication of these candidate materials for next-generation memory and logic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Synthesis and transport properties of epitaxial Bi (111) films on GaAs (111) substrates

In recent decades, the growth of ultrathin epitaxial bismuth (Bi) films on various substrates has garnered interest due to their unique electronic properties. We report upon the growth and electrical transport properties of epitaxial Bi (111) films in the thickness range of 5–32 nm deposited directly on GaAs (111) substrates, without a buffer layer. The quality of Bi films is found to depend on conditions for substrate treatment using Ar + ion-milling and annealing. Substrates milled at low ion beam currents display poor surface reconstruction after annealing, which hinders the growth of high-quality films. In contrast, substrates milled under optimized conditions led to reconstructed surfaces upon annealing, resulting in epitaxial Bi films with predominantly single-domain orientation. Although epitaxial films formed in both cases, transport measurements indicated significantly higher conductivity for films grown on optimally treated substrates. Measurements at low temperatures suggest that the transport properties are dominated by a surface state with high mobility electrons. Magneto-transport measurements suggest that conductivity and mobility improve progressively with increasing film thickness. For the thinnest 5 nm film, a hole-like state emerges, presumably as the electron-like state is gapped out. These results provide a robust methodology for growing high-quality epitaxial Bi films on GaAs (111) and offer insights into their unique transport properties and our ability to tune them.

Atomic force microscopy↗
DOE OSTI2024

Wet chemistry-synthesized Fe/mixed ferrite soft magnetic composites for high-frequency power conversion

State-of-the-art soft magnetic (SM) alloy systems such as electrical steels and permalloys exhibit large eddy current losses at high-frequency (kHz range and above), limiting their application in fast switching devices. Eddy current losses can be reduced for metallic alloys through a decrease in characteristic length scale or embedding them in an insulation layer. This work proposes the development of fine-scale core materials consisting of metallic SM nano/microparticles with magnetic, inorganic insulation layers, and their synthesis using a wet chemistry-based, scalable method for high frequency and high-power applications. More specifically, a magnetic ferrite coating (Ni 0.5-x Mn x Zn 0.5 Fe 2 O 4 , x = 0.0–0.5) was applied via deposition of ferrite powder produced using a “wet chemistry-based” co-precipitation method; the ferrite was distributed through the Fe micropowder via either ball milling or ultrasonic mixing. Powder cores were prepared by compaction of the synthesized composites. Relative magnetic permeability and core loss were measured at excitation frequencies to 200 kHz. A core loss of 127 kW/m 3 was measured at excitation frequency of 100 kHz and magnetization of 0.02 T. This value improves on the 199.3 kW/m 3 reported in literature at identical excitation conditions for a compact formed from a composite comprising Fe microparticles coated with low-permeability Ni 0.5 Zn 0.5 Fe 2 O 4 . Ultrasonic mixing resulted in slightly lower core loss than ball milling, possibly because ball milling causes loss-increasing deformation of the Fe micropowder. XRD and SEM were used to observe composite composition and core cross-section microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unraveling the origin of antiferromagnetic coupling at YIG/permalloy interface

We investigate the structural and electronic origin of antiferromagnetic (AFM) coupling in the yttrium iron garnet (YIG) and permalloy (Ni 80 ⁢Fe 20 , Py) bilayer system at the atomic level. Ferromagnetic resonance (FMR) spectra reveal unique hybrid modes in samples prepared with surface ion milling, indicative of antiferromagnetic exchange coupling at the YIG/Py interface. Using atomic resolution scanning transmission electron microscopy (STEM), we found that AFM coupling appears at the YIG/Py interface of the tetrahedral YIG surface formed with ion milling. Here, the STEM measurements suggest that the interfacial AFM coupling is predominantly driven by an oxygen-mediated superexchange coupling mechanism, which is confirmed by the density-functional theory (DFT) calculations to be energetically favorable. Thus, the combined experimental and theoretical results reveal the critical role of interfacial atomic structure in determining the type of magnetic coupling in a YIG/ferromagnet heterostructure, and prove that the interfacial structure can be experimentally tuned by surface ion milling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of Urbix Resources Natural Flake Graphite Material for Nuclear Applications (CRADA NFE-18-07340 Final Report)

Urbix Resources is a company specializing in graphite powder processing and purification. Urbix is looking to become the first domestic supplier of nuclear-grade graphite in the United States. This has led to a Cooperative Research and Development Agreement (CRADA) being established between the Oak Ridge National Laboratory (ORNL) and Urbix Resources, with the goal of characterizing a purified graphite feedstock supplied by Urbix Resources. The resulting data will then be used to determine the viability of a large-scale nuclear graphite production and qualification campaign. These characterization methods have been performed on the as-received graphite feedstock, a heat-treated batch of the feedstock, a milled batch of the feedstock, and a nuclear-grade graphite powder historically used in fuel production. The data from the heat-treated and milled feedstock will determine how different processing methods affect the powder’s physical properties, whereas the data from the nuclear grade graphite will provide information about the characteristics of a graphite previously accepted for nuclear applications. All of these powders have been characterized individually and as part of a resin-graphite blend (herein referred to as matrix) that has been used in past fuel experiments. The results of these experiments show that the Urbix powder and nuclear-grade graphite powder display notably different properties from one another in many cases, but this discrepancy may have been the result of the typical particle size of each powder. This hypothesis is supported by tests conducted on the milled powder, which showed a closer resemblance in properties to the nuclear-grade graphite than the as-received powder. The method for pressing the graphite matrix also had a noticeable effect on the measured properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Explore the Potential to Formulate Feedstock Blends from Diverse Biomass inputs for Improved Processing Performance at Lower Costs

This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat-die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of >550 kg/m3 and durability of >95. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption. Tests were also conducted on blends of pine and switchgrass using a pilot scale pellet mill by varying the blend moisture content and compression ratio of the pellet die. Pelleting tests on pure pine and switchgrass and their blends in a pilot scale ring die pellet mill with a throughput of 1 ton/h has indicated pellets with durability >500 kg/m3 and durability in the range of >90 and >95 %. The demonstration of high moisture pelleting of blends of 2- and 6-inch top pine residues and switchgrass blends indicated that good quality pellets with durability >90 % and bulk density of >500 kg/m3 can be produced.

09 BIOMASS FUELS↗
DOE OSTI2020

Literature Review of Documented Persistent Secondary Uranium Sources at DOE LM Sites

The U.S. Department of Energy Office of Legacy Management (LM) has the responsibility to protect human health and the environment at 101 legacy uranium sites across the nation by implementing long-term surveillance and maintenance requirements. Included in these responsibilities is to provide for the safe and environmentally sound disposal, long-term stabilization, and control of uranium mill tailings in a manner that minimizes or eliminates radiation health hazards to the public at 21 Uranium Mill Tailings Radiation Control Act (UMTRCA) Title I sites; 6 UMTRCA Title II sites; and 9 Comprehensive Environmental Response, Compensation, and Liability Act/Resource Conservation and Recovery Act sites. These sites are former uranium mills (processing sites), or sites with wastes from processing sites encapsulated in engineered disposal cells (disposal sites), or sites where components of atomic weapons were manufactured. During site characterization, groundwater contamination was often discovered and evaluated or modeled for future movement with the inclusion of uranium sorption in the groundwater plume. Much of this original work did identify uranium processing wastes as the original contaminant source. However, more recent work has identified the existence and influence of persistent secondary uranium sources that may prevent uranium in groundwater from attenuating as quickly as initial evaluations or modeling indicated. By understanding these processes, better decisions can be made to choose the appropriate remediation and closure strategies, identify long-term surveillance and maintenance activities, and more accurately estimate life-cycle costs. The purpose of this report is to summarize the literature available on documented persistence secondary uranium sources at LM sites as part of the Applied Studies and Technology Persistent Secondary Contaminant Sources Project.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Report Summarizing the Mechanical Properties of a Large ODS Ferritic Alloy Ingot by Forging at High Temperatures for Future Mother Tube Production

Oxide dispersion strengthened (ODS) ferritic alloys are considered the benchmark fuel cladding and core structural material in advanced nuclear energy reactors that require high-temperature strength and creep properties and resistance to radiation damage. The ODS ferritic alloys including 14YWT are produced by mechanical alloying (MA), which is time-consuming and is associated with high manufacturing costs that are not beneficial to being used in advanced nuclear energy reactors. This report summarizes the accomplishments in FY24 in the INM program for producing an ODS ferritic alloy by high-deformation, high-temperature processing of reactive and ferritic alloy powders for advanced reactor fuel cladding applications. Following four hot forging experiments, it was concluded that several significant challenges were encountered that were difficult to overcome. These challenges were related to using high annealing temperatures for pressure assisted sintering processes to produce dense microstructures, but the high annealing temperatures result in long range diffusion of Ti through the bcc Fe lattice and react with the YIG particles that are distributed on the prior surfaces of the ferritic alloy powders. In addition, it was determined that the high deformations induced by forging at high temperatures were not very effective for fracturing the reactive YIG particles into smaller particles and distributing them into the interior of the ferritic alloy powders. Spark plasma sintering was attempted for shortening the time at high temperatures, which led to full densification but the microstructure characterization results still showed that Ti atoms diffused over long distances in the bcc Fe lattice and reacted with the YIG particles. Finally, a short 30 minute high intensity ball milling experiment was conducted on blended 14WT and YIG powders for inducing severe deformations that caused the initially spherical powders of 14WT decorated with the YIG particles on the surfaces to transform to flakes and fracturing of YIG particles into smaller particles that were incorporated into the bcc Fe lattice. Two forgings were performed with the high intensity milled powders: first annealing for 20 minutes at 850ºC followed by forging and second annealing for 20 minutes at 1,100ºC followed by forging. At 850ºC, Ti atoms are effectively immobile, thus allowing for densification albeit incomplete. The deformation by forging after annealing for 20 minutes at 1,100ºC favored dynamic recrystallization processes that led to nano-size grains with very high stored energy due to high dislocation density. The corresponding VH data showed significant hardening that correlated with estimated strengthening of ~1650 MPa. This hybrid processing approach combining high intensity ball milling of powder with annealing and forging showed the most promise for producing an oxide dispersing strengthened ferritic alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride

The difficult ignition of boron decreases the combustion efficiency of boron-loaded, fuel-rich propellants. One approach to solving this problem involves the use of magnesium diboride (MgB2), which ignites easier than boron. Magnesium tetraboride (MgB4) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures were recently recognized as promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their thermal decomposition, oxidation, and combustion. The MgB2 and MgB4 powders were fabricated by combustion synthesis in the chemical oven mode and by heating Mg/B mixtures in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by high-energy ball milling. Thermal decomposition and oxidation of the obtained MgB₂ and MgB₄ powders were investigated by conducting non-isothermal thermogravimetric analysis (TGA) at temperatures up to 1550 °C in argon and oxygen flows. Combustion of B, MgB₂, and MgB₄ powders with oxygen at atmospheric pressure was studied in a windowed chamber using laser ignition and high-speed video recording. The TGA has shown multi-step decomposition of both magnesium borides in an argon environment. The maximum oxidation rate of MgB4 in oxygen was observed at a much lower temperature than in the case of MgB2. In the combustion experiments, both magnesium borides burned much faster than submicron boron. Ball milling of the borides further increased their burning rates. It has been concluded that nanoscale magnesium tetraboride is a promising ingredient for fuel-rich propellants owing to its high energy density, efficient oxidation, and rapid combustion.

Molina, Andre [The University of Texas at El Paso]↗
DOE OSTI2024

Two-dimensional heteronuclear single quantum coherence (HSQC) NMR spectra of lignin isolated from field grown transgenic poplar

Here we present a curated dataset of a series of two-dimensional heteronuclear single quantum coherence (HSQC) nuclear magnetic resonance (NMR) spectra of lignin isolated from a field grown transgenic poplar engineered with a monolignol 4-O-methyltransferase (MOMT4). The poplar was collected from a 2-year-old rotation trees within a three-year field trial experiment. The poplar was Soxhlet-extracted with toluene/ethanol and the extractives-free poplar was then ball-milled in a Retsch PM100 planetary ball mill using a porcelain jar with ceramic balls at 600 rpm for 2 h (in 5 min on and 5 min off cycles to avoid excessive sample heating). The ball-milled materials were then subjected to enzymatic hydrolysis for 48 h followed by centrifugation and washing with deionized water. The solid residue was extracted twice with 96:4 (v/v) 1,4-dioxane/water mixture at room temperature overnight. The extracts were combined, rotary evaporated, and freeze-dried to recover the lignin. The dry lignin samples were dissolved in deuterated dimethyl sulfoxide for NMR experiments. 13C–1H HSQC experiments were performed in a Bruker Avance III HD 500 MHz NMR spectrometer operating at a frequency of 125.12 MHz for the 13C nucleus using a standard Bruker pulse sequence (hsqcetgpsisp2.2) on a Prodigy platform cryoprobe. The NMR spectra were acquired under the following acquisition conditions: 220 ppm spectral width in F1 (13C) dimension with 256 data points and 12 ppm spectral width in F2 (1H) dimension with 1024 data points, a 90° pulse, a one bond C–H coupling constant of 145 Hz, a 1.0 s pulse delay, and 64 scans. All the data was processed using the Bruker’s TopSpin 3.6 software. The NMR spectra provides structural characteristics information about lignin in field grown transgenic MOMT4 poplar. Additional meta data is embedded in the raw spectra figures.

Lignin structure, HSQC, poplar, field trial, MOMT4↗