Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “METEOROIDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Hubble Space Telescope meteoroid-debris protection analysis

A system level failure could occur if the Hubble Space Telescope's (ST) capability to operate as a facility on-orbit is critically reduced or when a significant reduction in the quality of science data is registered. Failure could occur if a meteoroid/debris impact damages a component of a major support subsystem or if a meteoroid/debris penetration causes straylight contamination in the light shield, forward shell, aft shroud, or through the aperture door. The ST was analyzed to find the probability of no critical penetration. This probability value was found to be 92.25% for a two-year service life. A straylight leakage repair technique was recommended for the aft shroud, the region found most likely to be critically penetrated. Fozar tape and multilayer insulation blankets are suggested as posible repair materials.

Horn, J.↗
NASA NTRS1985

Examination of returned solar-max surfaces for impacting orbital debris and meteoroids

The thermal insulation of the Solar Maximum Mission launched on 14 February 1980 which consisted of 17 layers of alumized Kapton offers an excellent opportunity to obtain chemistry of impacting particles. To date, approximately 0.7 sq. met. of the insulation and 0.05 sq. met. of the aluminum louvers have been mapped by optical microscope for crater diameters larger than 40 microns. Atomic oxygen has eroded up to 20 microns of the exposed Kapton surfaces removing the older and smaller craters. The crater size distribution found on 3 different Kapton surfaces is shown. About 250 chemical spectra were recorded of particles observed in or around impact pits or in the debris pattern found on the second layer beneath impact holes in the outer layer. The debris populations are listed and discussed.

Kessler, D. J.↗
NASA NTRS1987

Ozone formation due to interaction of meteoroids with Earth's atmosphere

In a previous paper, it was shown that concentration of atomic oxygen in overdense meteor trails may exceed that of the normal atmosphere by a factor of several hundred times. This may lead to the formation of meteoric ozone. Therefore, it is imperative to estimate the concentration of ozone in the trails of meteor bodies with different masses. It seems that meteoric ozone must be taken into account when studying the balance of ionization in the meteor trails formed by particles with masses more than .01 g. The predicted levels of atomic oxygen and ozone seem sufficient to greatly influence the rate of meteoric plasma deionization.

Bibarsov, R. SH.↗
NASA NTRS1989

The detection and observation of meteoroid and space debris impact features on the Solar Max satellite

The results of optical observations on the entire population of impact pits and holes discovered on nearly all of the returned parts of the Solar Maximum Mission satellite are described. Some statistically significant new results on impact dynamics are obtained as well as new number vs. size distributions for craters and holes ranging from 40 to 900 microns. The local spacecraft geometric shielding corrections are calculated and applied to the data. Some selected compositional results are presented which indicate that the Space Shuttle can be a source of impacting debris.

Warren, J. L.↗
NASA NTRS1990

Advanced meteoroid and debris shielding concepts

The results of the shielding screening and optimization work conducted at the NASA Johnson Space Center Hypervelocity Impact Research Laboratory (HIRL) are described. The impact tests to investigate and optimize certain aspects of the aluminum mesh double-bumper concept, which was considered the best performer in the screening test, are analyzed. Preliminary results indicate that the aluminum mesh double-bumper concept shows a 30 to 40 percent weight reduction compared to an aluminum Whipple shield in the velocity range study, besides such advantages as an increased resistance to penetration and the fact that the aluminum mesh does not produce damaging secondary ejecta particles. It is suggested that the ballistic protection can be improved even more if an intermediate layer of a high-strength cloth is attached near the rear wall.

Christiansen, Eric L.↗
NASA NTRS1991

Study of meteoroid impact craters on various materials (AO 138-1). Attempt at dust debris collection with stacked detectors (AO 138-2)

Part of the Long Duration Exposure Facility (LDEF) tray allocated to French experiments, known as FRECOPA payload, was devoted to the study of dust particles. Two passive experiments were flown: one composed of a set of glass and metallic samples and one composed of multilayer thin foils detectors. In addition to these experiments, a broad variety of materials were exposed to the bombardment of microparticles and provide more data. Thick target experiment comprises selected metallic (Al, Au, Cu, W, Stainless Steel) 250 microns thick and glass surfaces 1.5 mm thick. Crater size distribution from these thick target experiments enable, with the aid of lab calibrations by solid particle accelerators, the evaluation of the incident microparticle flux in the near earth environment. The aim of the multiple foil penetration and collection experiment is primarily to study the feasibility of multilayer thin film detectors acting as energy sorters in order to collect micrometeoroids, if not in their original shape, at least as 'breakup' fragments suitable for chemical analysis. Foil thicknesses range from 0.75 to 5 microns of Al.

Mandeville, Jean Claude↗
NASA NTRS1991

Meteoroid and orbital debris record of the Long Duration Exposure Facility

The Long Duration Exposure Facility (LDEF) was recovered in January 1990 following 5.7 years exposure of approx. 130 square meters of surface area in low-Earth orbit (250-179 miles). Kennedy Space Center acquired data are currently being reduced to yield accurate impact crater depths and diameters. Presented here is a preliminary accounting of the impact record based on the approx. 15.4 square meter surface area of LDEF's 6061-T6 aluminum frame, which was exposed in 26 different directions.

Zolensky, Mike↗
NASA NTRS1990

Compositional range in the Canyon Diablo meteoroid

The compositional range within the Canyon Diablo (CD) iron meteorites associated with the formation of the Meteor Crater (Arizona) was examined, using the INAA to analyze a set of CD samples consisting of nine irons collected within 7 km of the Meteor Crater, four Arizona IAB irons that were identified by Wasson (1968) as transported CD fragments, and irons from Las Vegas (Nevada) and Moab (Utah) that Buchwald (1975) suggested to be transported CD fragments. Results show that the irons named Helt Township, Idaho, Las Vegas, Mamaroneck, Moab, and Pulaski County are, most likely, mislabeled CD specimens. On the other hand, meteorites named Alexander County, Allan Hills A77283, Ashfork, Fairfield, and Rifle are identified as compositionally distinct independent falls.

Wasson, John T.↗
NASA NTRS1992

Meteoroid and debris special investigation group data acquisition procedures

The entire LDEF spacecraft was examined by M&D SIG for impact (i.e., craters greater than or = 0.5 mm and penetrations greater than or = 0.3 mm in diameter) and related features (e.g., debris, secondaries). During the various detailed surveys conducted at NASA Kennedy, approx. 5,000 impact related features were photodocumented, and their locations measured and recorded; an additional approx. 30,000 smaller features were counted. The equipment and techniques used by the M&D SIG permitted the determination and recording of the locations and diameters of the 5,000 imaged features. A variety of experimental and LDEF structural hardware was acquired by the M&D SIG and is presently being examined and curated at NASA Johnson.

See, Thomas H.↗
NASA NTRS1992

Meteoroid, and debris special investigation group preliminary results: Size-frequency distribution and spatial density of large impact features on LDEF

All craters greater than or equal to 500 microns and penetration holes greater than or equal to 300 microns in diameter on the entire Long Duration Exposure Facility (LDEF) were documented. Summarized here are the observations on the LDEF frame, which exposed aluminum 6061-T6 in 26 specific directions relative to LDEF's velocity vector. In addition, the opportunity arose to characterize the penetration holes in the A0178 thermal blankets, which pointed in nine directions. For each of the 26 directions, LDEF provided time-area products that approach those afforded by all previous space-retrieved materials combined. The objective here is to provide a factual database pertaining to the largest collisional events on the entire LDEF spacecraft with a minimum of interpretation. This database may serve to encourage and guide more interpretative efforts and modeling attempts.

See, Thomas H.↗
NASA NTRS1992

Detailed examination of LDEF's frame and the A0178 thermal blankets by the meteoroid and debris special investigations group

A responsibility of the group is to define the hypervelocity particle environment encountered by LDEF during its stay in low Earth orbit. LDEF's 6061-T6 aluminum frame and the 'Teflon silver-inconel paint' thermal blankets represent large surface areas that were widely distributed around the spacecraft. The results are reported of high resolution scans of approx. 0.36 and approx. 0.31 sq m for the intercostals and thermal blankets, respectively. The findings are in qualitative agreement with existing model predictions that suggest high differential bombardment histories for surfaces pointing into specific directions relative to the velocity vector of a non-spinning platform in LEO. The production rate for craters greater than or = 50 microns in diameter in aluminum and penetration holes greater than or = 100 microns in diameter in thin foil materials differ by more than a factor of 10 between forward and rearward facing surfaces. These are substantial differences that must be considered during the design of future long duration space platforms in LEO.

See, Thomas H.↗
NASA NTRS1992

Meteoroid and debris special investigation group; status of 3-D crater analysis from binocular imagery

During the 3 month deintegration of the LDEF, the M&D SIG generated approximately 5000 digital color stereo image pairs of impact related features from all space exposed surfaces. Currently, these images are being processed at JSC to yield more accurate feature information. Work is currently underway to determine the minimum number of data points necessary to parametrically define impact crater morphologies in order to minimize the man-hour intensive task of tie point selection. Initial attempts at deriving accurate crater depth and diameter measurements from binocular imagery were based on the assumption that the crater geometries were best defined by paraboloid. We made no assumptions regarding the crater depth/diameter ratios but instead allowed each crater to define its own coefficients by performing a least-squares fit based on user-selected tiepoints. Initial test cases resulted in larger errors than desired, so it was decided to test our basic assumptions that the crater geometries could be parametrically defined as paraboloids. The method for testing this assumption was to carefully slice test craters (experimentally produced in an appropriate aluminum alloy) vertically through the center resulting in a readily visible cross-section of the crater geometry. Initially, five separate craters were cross-sectioned in this fashion. A digital image of each cross-section was then created, and the 2-D crater geometry was then hand-digitized to create a table of XY position for each crater. A 2nd order polynomial (parabolic) was fitted to the data using a least-squares approach. The differences between the fit equation and the actual data were fairly significant, and easily large enough to account for the errors found in the 3-D fits. The differences between the curve fit and the actual data were consistent between the caters. This consistency suggested that the differences were due to the fact that a parabola did not sufficiently define the generic crater geometry. Fourth and 6th order equations were then fitted to each crater cross-section, and significantly better estimates of the crater geometry were obtained with each fit. Work is presently underway to determine the best way to make use of this new parametric crater definition.

Sapp, Clyde A.↗
NASA NTRS1992

Ballistic limit regression analysis for Space Station Freedom meteoroid and space debris protection system

Relationships defining the ballistic limit of Space Station Freedom's (SSF) dual wall protection systems have been determined. These functions were regressed from empirical data found in Marshall Space Flight Center's (MSFC) Hypervelocity Impact Testing Summary (HITS) for the velocity range between three and seven kilometers per second. A stepwise linear least squares regression was used to determine the coefficients of several expressions that define a ballistic limit surface. Using statistical significance indicators and graphical comparisons to other limit curves, a final set of expressions is recommended for potential use in Probability of No Critical Flaw (PNCF) calculations for Space Station. The three equations listed below represent the mean curves for normal, 45 degree, and 65 degree obliquity ballistic limits, respectively, for a dual wall protection system consisting of a thin 6061-T6 aluminum bumper spaced 4.0 inches from a .125 inches thick 2219-T87 rear wall with multiple layer thermal insulation installed between the two walls. Normal obliquity is d(sub c) = 1.0514 v(exp 0.2983 t(sub 1)(exp 0.5228). Forty-five degree obliquity is d(sub c) = 0.8591 v(exp 0.0428) t(sub 1)(exp 0.2063). Sixty-five degree obliquity is d(sub c) = 0.2824 v(exp 0.1986) t(sub 1)(exp -0.3874). Plots of these curves are provided. A sensitivity study on the effects of using these new equations in the probability of no critical flaw analysis indicated a negligible increase in the performance of the dual wall protection system for SSF over the current baseline. The magnitude of the increase was 0.17 percent over 25 years on the MB-7 configuration run with the Bumper II program code.

Jolly, William H.↗
NASA NTRS1993

Corvid meteoroids are not ejecta from the Giordano Bruno impact

The study points out three difficulties with the hypothesis of Hartung (1993) that the Corvid meteor system, observed only once in 1937, may be the return of the clump of ejecta from the formation of a lunar crater, specifically, an event recorded in the chronicles of Gervase of Canterbury on June 25, 1178, which Hartung (1976) previously suggested may be an eyewitness account of the formation of the lunar crater Giordano Bruno. On the basis of this, he predicts that another Corvid shower may be observed in 2003 or 2006. This hypothesis is rejected on the contention that it is implausible that a clump of ejecta could be launched into heliocentric orbit with a low enough dispersion in velocity among separate pieces that it would produce a meteor shower in just one year and not others. Subsequent perturbations by the earth on parts of the clump passing near the earth but not impacting would destroy the coherence of the clump on a time scale much shorter than the 759-yr interval proposed. There are so many orbits that could yield a shower after 759 yr that it is unlikely that a prediction of a return in a specific year would be correct.

Harris, A. W.↗
NASA NTRS1992

Meteoroid environment near the Earth-Moon system

We undertook a research program to investigate the properties of small objects crossing the orbit of the Earth-Moon system using a unique set of data obtained during the Apollo lunar landing missions with a network of seismic stations on the surface of the Moon. The primary objectives of the study were to find out the nature of these objects, whether they were of cometary or asteroidal origin based on their orbital distributions and seismic effects upon impacts, and then to infer the role these small objects play in the evolution of the solar system. In this final technical report, we briefly summarize the results of this study. Detailed results of the study have been published in a series of papers and a dissertation, which are listed in the PUBLICATIONS section. Abstracts of the published papers and the dissertation are attached as an appendix.

Nakamura, Yosio↗
NASA NTRS1994

Morphology of meteoroid and space debris craters on LDEF metal targets

We measured the depths, average diameters, and circularity indices of over 600 micrometeoroid and space debris craters on various metal surfaces exposed to space on the Long Duration Exposure Facility (LDEF) satellite, as a test of some of the formalisms used to convert the diameters of craters on space-exposed surfaces into penetration depths for the purpose of calculating impactor sizes or masses. The topics covered include the following: targe materials orientation; crater measurements and sample populations; effects of oblique impacts; effects of projectile velocity; effects of crater size; effects of target hardness; effects of target density; and effects of projectile properties.

Love, S. G.↗
NASA NTRS1997

Measurements of micron-scale meteoroids and orbital debris with the Space Dust (SPADUS) instrument on the upcoming ARGOS P91-1 mission

The space dust (SPADUS) experiment, to be launched into a sun-synchronous polar orbit at an altitude of 833 km onboard the USAF ARGOS P91-1 mission, will provide time-resolved measurements of the intensity, size spectrum and geocentric trajectories of dust particles encountered during the nominal three year mission. The experiment uses polyvinylidene fluoride dust sensors with a total detector area of 576 sq cm. The SPADUS will measure particle sizes between 2 and 200 microns, particle velocities between 1 and 10 km/s to better than 4 percent, and the direction of incidence with a mean error of 7 percent. These data will identify the particles as being debris or of natural origin.

McKibben, R. B.↗