Results for “Graphite Properties” — Page 25

NASA NTRS1985

Siloxane containing polyimides with improved processability

Siloxane containing polyimides were prepared in an effort to improve processability of linear aromatic polyimides and toughness of addition curing imide oligomers. Linear aromatic polyimides were endcapped with varying proportions of a silane; a diaminosiloxane was copolymerized with an aromatic diamine; polyimide oligomers were endcapped with reactive groups; and acetylene terminated siloxane-containing oligomers were blended with linear siloxane-containing polyimides. The resins were used to prepare moldings, titanium to titanium adhesive bonds, and graphite reinforced composites. In each case, physical properties and other characteristics were compared to those of chemically similar polyimides with no siloxane incorporation. The resins, in most cases, performed better at room temperature than the corresponding polyimide. At elevated temperatures, for high siloxane content, the performance deteriorated.

Maudgal, Shubha↗

NASA NTRS1984

Processing and flammability parameters of bismaleimide and some other thermally stable resin matrices for composites

The effect of processing variables on the flammability and mechanical properties of state-of-the-art and advanced resin matrices for graphite composites were studied. Resin matrices which were evaluated included state-of-the-art epoxy, phenolic-novolac, phenolic-Xylok, two types of bismaleimides, benzyl, polyethersulfone, and polyphenylsulfone. Comparable flammability and thermochemical data on graphite-reinforced laminates prepared with these resin matrices are presented, and the relationship of some of these properties to the anaerobic char yield of the resins is described.

Kourtides, D. A.↗

NASA NTRS1985

Homogeneity of pristine and bromine intercalated graphite fibers

Wide variations in the resistivity of intercalated graphite fibers and to use these materials for electrical applications, their bulk properties must be established. The homogeneity of the diameter, the resistivity, and the mass density of 50 graphite fibers, before and after bromine intercalation was measured. Upon intercalation the diameter was found to expand by about 5%, the resistivity to decrease by a factor of five, and the density to increase by about 6%. Each individual fiber was found to have uniform diameter and resistivity over macroscopic regions for lengths as long as 7 cm. The ratio of pristine to intercalated resistivity increases as the pristine fiber diameter increases at a rate of 0.16 micron, but decreases with the increasing ratio of intercalated diameter to pristine diameter at a rate of 0.08.

Gaier, J. R.↗

NASA NTRS1986

Apparatus for producing diamond-like carbon flakes

A vacuum arc from a spot at the face of a graphite cathode to a graphite anode produces a beam of carbon ions and atoms. A carbon coating from this beam is deposited on an ion beam sputtered target to produce diamond-like carbon flakes. A graphite tube encloses the cathode, and electrical isolation is provided by an insulating sleeve. The tube forces the vacuum arc spot to be confined to the surface on the outermost end of the cathode. Without the tube the arc spot will wander to the side of the cathode. This spot movement results in low rates of carbon deposition, and the properties of the deposited flakes are more graphite-like than diamond-like.

Banks, Bruce A.↗

NASA NTRS1986

Structure-to-property Relationships in Addition Cured Polymers 2: Resin Tg Composite Initial Mechanical Properties of Norbornenyl Cured Polyimide Resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, W. B.↗

NASA NTRS1986

Structure-to-property relationships in addition cured polymers. II - Resin Tg and composite initial mechanical properties of norbornenyl cured polyimide resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, William B.↗

NASA NTRS1988

The 700 F properties of autoclave cured PMR-2 composites

Studies were conducted to develop autoclave processing parameters for graphite reinforced PMR-2 resin composite materials intended for use in applications at temperatures up to 371 degrees (700 F). The effect of resin composition on autoclaveability was investigated. The effect of various graphite fibers and resin composition on 343 C (650 F) and 371 C (700 F) thermo-oxidative stability and mechanical properties was also investigated. The results of the processing studies show that PMR-2 resin composites can be easily fabricated under autoclave conditions. Autoclaved laminates exposed to 1 atm of air at 343 C (650 F) and 371 C (700 F) exhibited less than 5 percent weight loss after 750 hr exposure to 650 F air and 8 percent weight loss during exposure to 700 F air for 500 hr. After 500 hr exposure, autoclaved laminates exhibited greater than 90 percent retention of initial 650 and 700 F flexural and interlaminar shear strengths. The effect of resin formulated molecular weight and postcure conditions on laminate glass transition temperature is also discussed.

Vannucci, Raymond D.↗

DOE OSTI2025

Update on R&D progress by DOE

High temperature materials and graphite and composite program review to include: Baseline for unirradiated material properties, ASTM test development, design and construction rules (ASME-based), new fuel matrix mechanical studies, Irradiation damage studies, vender irradiation capsules, graphite supply chain worries, and ceramic composite activities.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Tunable mechanical behavior of graphene nanoribbon-metal composites fabricated through an electrocharge-assisted process

This work investigates the role of a carbon nanophase on the local mechanical behavior of nanocarbon metal matrix composites (NCMCs) produced through an electrocharge-assisted process. Nanoindentation experiments on single crystal Al, Al 1350 parent alloys, and Al 1350 NCMCs revealed variable mechanical properties, caused by an interplay between microstructure and graphitic reinforcements. TEM and AFM studies also reveal nanoscale structural changes based on the incorporation of a carbon nanophase. In order to decouple the effects of the aforementioned mechanical behaviors, molecular dynamics nanoindentation simulations were performed on the (111) surface of Al and Al NCMC samples containing semi-infinite graphene nanoribbons to examine the evolution of plasticity over time. Findings indicate that the arrangement of a finite graphene nanophase within a host matrix can alter plasticity mechanisms and therefore yield strength in near-surface mechanical behavior with little effect on elastic properties. Here, this understanding enables further study into tunable bulk properties of Al-based NCMCs while isolating microstructural effects and reinforcement effects of the carbon phase. Such an understanding will lead to application-specific material geometries ranging from highperforming vehicle structures to next-generation electrical devices.

36 MATERIALS SCIENCE↗

NASA NTRS1990

Intercalated graphite fiber composites as EMI shields in aerospace structures

The requirements for electromagnetic interference (EMI) shielding in aerospace structures are complicated over that of ground structures by their weight limitations. As a result, the best EMI shielding materials must blend low density, high strength, and high elastic modulus with high shielding ability. In addition, fabrication considerations including penetrations and joints play a major role. The EMI shielding properties are calculated for shields formed from pristine and intercalated graphite fiber/epoxy composites and compared to preliminary experimental results and to shields made from aluminum. Calculations indicate that EMI shields could be fabricated from intercalated graphite composites which would have less than 12 percent of the mass of conventional aluminum shields, based on mechanical properties and shielding properties alone.

Gaier, James R.↗

NASA NTRS1976

Carbide coated fibers in graphites-aluminum composites

Research activities are described for a NASA-supported program at the Los Alamos Scientific Laboratory to develop graphite fiber-aluminum matrix composites. A chemical vapor deposition apparatus was constructed for continuously coating graphite fibers with TiC. As much as 150 meters of continuously coated fibers were produced. Deposition temperatures were varied from 1365 K to about 1750 K, and deposition time from 6 to 150 seconds. The 6 sec deposition time corresponded to a fiber feed rate of 2.54 m/min through the coater. Thin, uniform, adherent TiC coats, with thicknesses up to approximately 0.1 micrometer were produced on the individual fibers of Thornel 50 graphite yarns without affecting fiber strength. Although coat properties were fairly uniform throughout a given batch, more work is needed to improve the batch-to-batch reproducibility. Samples of TiC-coated Thornel 50 fibers were infiltrated with an aluminum alloy and hot-pressed in vacuum to produce small composite bars for flexure testing. Strengths as high as 90% of the rule-of-mixtures strength were achieved. Results of the examination of the fracture surfaces indicate that the bonding between the aluminum and the TiC-coated fibers is better than that achieved in a similar, commercially infiltrated material made with fibers having no observable surface coats. Several samples of Al-infiltrated, TiC-coated Thornel 50 graphite yarns, together with samples of the commercially infiltrated, uncoated fibers, were heated for 100 hours at temperatures near the alloy solidus. The TiC-coated samples appear to undergo less reaction than do the uncoated samples. Photomicrographs are shown.

Imprescia, R. J.↗

NASA NTRS1988

700 F properties of autoclave cured PMR-II composites

Studies were conducted to develop autoclave processing parameters for graphite reinforced PMR-2 resin composite materials intended for use in applications at temperatures up to 371 degrees (700 F). The effect of resin composition on autoclaveability was investigated. The effect of various graphite fibers and resin composition on 343 C (650 F) and 371 C (700 F) thermo-oxidative stability and mechanical properties was also investigated. The results of the processing studies show that PMR-2 resin composites can be easily fabricated under autoclave conditions. Autoclaved laminates exposed to 1 atm of air at 343 C (650 F) and 371 C (700 F) exhibited less than 5 percent weight loss after 750 hr exposure to 650 F air and 8 percent weight loss during exposure to 700 F air for 500 hr. After 500 hr exposure, autoclaved laminates exhibited greater than 90 percent retention of initial 650 and 700 F flexural and interlaminar shear strengths. The effect of resin formulated molecular weight and postcure conditions on laminate glass transition temperature is also discussed.

Cifani, Diane↗

DOE OSTI2025

The role of moisture in MgCl 2 salt: A multiscale approach to TES performance

This study presents a comprehensive multiscale analysis to evaluate the influence of moisture on the thermal performance of thermal energy storage systems using magnesium chloride (MgCl 2 ) as the phase-changing material. The system uses graphite foam with 90% relative density to enhance thermal conductivity. The analysis includes thermal conductivity calculations and specific heat capacity for different hydrate phases of MgCl 2 : Anhydrous, Mono, Di, Tetra, and Hexa. These properties were evaluated for the first time using the phonon density of states from Density Functional Theory simulations. Results showed that thermal conductivity decreased, while specific heat capacity increased by a factor of two as the phase changed from anhydrous to hexahydrate. Meso-scale models were created to account for the anisotropy of graphite foam and property variations of the MgCl 2 hydrate phases. Asymptotic Expansion homogenization simulations determined the anisotropic thermal conductivity for all phases. This unique methodology improved simulation accuracy, which matched experimental data for anhydrous MgCl 2 . A parametric study examined various operating conditions and their effect on TES performance. It revealed that higher charging temperatures did not enhance exergy efficiency, but increased discharge mass flow rates improved it due to better heat transfer. Thermal performance evaluated by the exergy efficiency remained consistent across hydrate systems under the tested conditions. Furthermore, the study suggests that this uniformity is linked to missing key data, particularly latent heat and melting point for different hydrates. Overall, it highlights the importance of multiscale effects and accurate material properties in designing and optimizing TES systems.

Molten salt degradation↗

NASA NTRS1998

Hydrogen Desorption and Adsorption Measurements on Graphite Nanofibers

Graphite nanofibers were synthesized and their hydrogen desorption and adsorption properties are reported for 77 and 300 K.

graphite nanofibers catalysts hydrogen desorption ↗

NASA NTRS1979

Graphite fiber reinforced glass matrix composites for aerospace applications

The graphite fiber reinforced glass matrix composite system is described. Although this composite is not yet a mature material, it possesses low density, attractive mechanical properties at elevated temperatures, and good environmental stability. Properties are reported for a borosilicate glass matrix unidirectionally reinforced with 60 volume percent HMS graphite fiber. The flexural strength and fatigue characteristics at room and elevated temperature, resistance to thermal cycling and continuous high temperature oxidation, and thermal expansion characteristics of the composite are reported. The properties of this new composite are compared to those of advanced resin and metal matrix composites showing that graphite fiber reinforced glass matrix composites are attractive for aerospace applications.

Prewo, K. M.↗

DOE OSTI2021

Integration of a Wigner effect-based energy storage system with an advanced nuclear reactor

In this work, an innovative energy storage concept based on the purposeful creation of defects in crystalline material by neutron irradiation is presented. Lattice defects are generated when heavy particles collide with the atoms in a crystal structure, i.e., if the incoming particles have enough energy, recoil atoms are displaced from their initial lattice sites. Most of the displaced atoms will eventually combine with nearby vacancies, but some of them will come to rest in non-ideal locations. The energy held by displaced atoms is called Wigner energy. Lattice defects can migrate and form clusters, and the Wigner energy can be released from these groupings if sufficient activation energy is provided. In the nuclear industry, this effect is well-known since it represented an issue for graphite-moderated reactors. This work presents the conceptual design of an engineering system that exploits this physical process to store the energy of neutrons in advanced reactor concepts. In the first part of the paper, the theoretical performance of an energy storage system based on the Wigner effect is described. Given the lattice properties and the compatibility with the harsh reactor environment, graphite was selected as the candidate material for the irradiation targets. Both experimental data and molecular dynamics simulations confirmed that this system can achieve performance comparable with state-of-the-art batteries in terms of stored energy density. In the second part of the paper, the engineering challenges of this innovative technology and the proposed solutions are described. After defining the optimal irradiation conditions, the different steps of the operation of the proposed energy system (from energy storing to energy harvesting) were defined. Finally, the integration of this concept with advanced reactor designs, i.e., a Sodium-cooled Fast Reactor and a Molten Salt-cooled Reactor, was investigated and the corresponding performance was evaluated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

Baseline Graphite Characterization

Baseline Graphite Characterization: Purpose of Baseline, Mechanical Baseline Tests, Physical Properties Tests, Methodology, Baseline progress, Density, Ultimate Tensile Strength, PCEA Ultimate Tensile Strength, Split Disc Tests, Compression Tests, Flexural Tests, and Coefficient of Thermal Expansion.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1981

Thermal expansion properties of composite materials

Thermal expansion data for several composite materials, including generic epoxy resins, various graphite, boron, and glass fibers, and unidirectional and woven fabric composites in an epoxy matrix, were compiled. A discussion of the design, material, environmental, and fabrication properties affecting thermal expansion behavior is presented. Test methods and their accuracy are discussed. Analytical approaches to predict laminate coefficients of thermal expansion (CTE) based on lamination theory and micromechanics are also included. A discussion is included of methods of tuning a laminate to obtain a near-zero CTE for space applications.

Johnson, R. R.↗