Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FILM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Rational Regulation of Layer‐by‐Layer Processed Active Layer via Trimer‐Induced Pre‐Swelling Strategy for Efficient and Robust Thick‐Film Organic Solar Cells

Thick-film (>300 nm) organic solar cells (OSCs) have garnered intensifying attention due to their compatibility with commercial roll-to-roll printing technology for the large-scale continuous fabrication process. However, due to the uncontrollable donor/acceptor (D/A) arrangement in thick-film condition, the restricted exciton splitting and severe carrier traps significantly impede the photovoltaic performance and operability. For this work, combined with layer-by-layer deposition technology, a twisted 3D star-shaped trimer (BTT-Out) is synthesized to develop a trimer-induced pre-swelling (TIP) strategy, where the BTT-Out is incorporated into the buried D18 donor layer to enable the fabrication of thick-film OSCs. The integrated approach characterizations reveal that the exceptional configuration and spontaneous self-organization behavior of BTT-Out trimer could pre-swell the D18 network to facilitate the acceptor's infiltration and accelerate the formation of D/A interfaces. This enhancement triggers the elevated polarons formation with amplified hole-transfer kinetics, which is essential for the augmented exciton splitting efficiency. Furthermore, the regulated swelling process can initiate the favorable self-assembly of L8-BO acceptors, which would ameliorate carrier transport channels and mitigate carrier traps. As a result, the TIP-modified thin-film OSC devices achieve the champion performance of 20.3% (thin-film) and 18.8% (thick-film) with upgraded stability, among one of the highest performances reported of thick-film OSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

PFSA-Ionomer Dispersions to Thin-Films: Interplay Between Sidechain Chemistry and Dispersion Solvent

In fuel-cell catalyst layers (CLs), ionomers exists as nanoscale thin-films binding catalyst particles, wherein ionic and gaseous species transport to catalyst sites. To improve film function, ionomers have been designed based on the prototypical perfluorosulfonic acid (PFSA). Since CLs are fabricated through solution-based processing of inks, understanding how ink/dispersion solvent impacts ionomer interactions and function is important to guide future ionomer design. Herein, PFSA and its chemical derivatives are characterized from dispersion (in solvent) to thin film (cast on support) to investigate the impact of solvent water content on ionomer dispersion (structure, acidity) and resulting film properties. Dispersion characterization reveals that secondary aggregate structure depends on the sidechain chemistry, but all PFSA-based ionomers evolve similarly as dispersion becomes water-rich. The differences in aggregation alter ionomer adsorption and thin film morphology. Further, hydrophilic domain spacing and orientation are affected primarily by sidechain chemistry, and modulated by solvent composition. Thin-film conductivity correlates with hydration and nanodomain alignment, signifying the role of morphology in properties. Overall, this work provides insights into how chemistry can be used to coarse-tune structure–property relationships, while processing solvent is for fine-tuning of dispersion-film interplay for controlling CL-ionomer function, which can be translated to other chemistries and ink formulations.

25 ENERGY STORAGE↗
DOE OSTI2021

Time-Resolved Grazing Incidence X-Ray Absorption Spectroscopy for the In Situ Investigation of the Initial Stages of Sputter-Deposited Copper Thin Films

The sputter deposition and the growth of thin copper films on float glass substrates are in situ studied using grazing incidence, reflection mode X-ray absorption fine structure spectroscopy with subsecond time resolution. The experimental data are compared with model calculations, assuming the presence of crystalline, face-centered cubic metallic Cu nanostructures. From a detailed analysis of the measured spectra, the film thickness as well as the surface roughness is determined, leading to a detailed understanding of the films growth as a function of the sputter deposition time. In particular, different stages of film growth can clearly be distinguished from the fits of the experimental data. The results suggest the formation of isolated, approximately nm-sized copper clusters in the initial phase of the film deposition for the first few seconds, a coalescence phase with a nominal thickness of ≈1.5–2.8 nm, constant roughness of about 1.4 nm for the subsequent ≈5 s, and finally 3D growth of the Cu crystallites in the film for later stages of film growth. Further prospects of the methodology are given.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fe Thin Film-Coated Optics for Corrosion Monitoring: Optical and Electrochemical Studies

Corrosion proxy materials integrated with an optical sensing platform enable a real-time optical corrosion sensor for natural gas pipelines to prevent methane leaks and catastrophic events. Effects of CO 2 , pH, and film thickness on corrosion of Fe thin films (25, 50, 100 nm) were studied using optical and electrochemical methods in 3.5%wt. NaCl solutions at 30 °C. An increase in light transmission (T%) corresponded to corrosion of Fe thin films. CO 2 accelerated corrosion of Fe thin films due to the lower pH and the promoted corrosion reactions, resulting in a faster increase of T% than without CO 2 or at higher pH. While the corrosion rate increased with increasing film thickness, electrochemical corrosion of Fe thin films was in good agreement with that of bulk carbon steel, verifying that Fe thin films can serve as a representative corrosion proxy when integrated with the optical sensing platform.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sputter-Deposited Mo Thin Films: Multimodal Characterization of Structure, Surface Morphology, Density, Residual Stress, Electrical Resistivity, and Mechanical Response

Multimodal datasets of materials are rich sources of information which can be leveraged for expedited discovery of process–structure–property relationships and for designing materials with targeted structures and/or properties. For this data descriptor article, we provide a multimodal dataset of magnetron sputter-deposited molybdenum (Mo) thin films, which are used in a variety of industries including high temperature coatings, photovoltaics, and microelectronics. In this dataset we explored a process space consisting of 27 unique combinations of sputter power and Ar deposition pressure. Here, the phase, structure, surface morphology, and composition of the Mo thin films were characterized by x-ray diffraction, scanning electron microscopy, atomic force microscopy, and Rutherford backscattering spectrometry. Physical properties—namely, thickness, film stress and sheet resistance—were also measured to provide additional film characteristics and behaviors. Additionally, nanoindentation was utilized to obtain mechanical load-displacement data. The entire dataset consists of 2072 measurements including scalar values (e.g., film stress values), 2D linescans (e.g., x-ray diffractograms), and 3D imagery (e.g., atomic force microscopy images). An additional 1889 quantities, including film hardness, modulus, electrical resistivity, density, and surface roughness, were derived from the experimental datasets using traditional methods. Minimal analysis and discussion of the results are provided in this data descriptor article to limit the authors’ preconceived interpretations of the data. Overall, the data modalities are consistent with previous reports of refractory metal thin films, ensuring that a high-quality dataset was generated. The entirety of this data is committed to a public repository in the Materials Data Facility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of endoglucanase and high-pressure homogenization post-treatments on mechanically grinded cellulose nanofibrils and their film performance

In this study, the effects of mechanical grinding (G) assisted by endoglucanase (E) and high-pressure homogenization (H) post-treated cellulose nanofibrils (CNFs) and its film properties were investigated. Compared to only mechanical grinding, these two post-treatment processes improved the size uniformity of CNFs in width. Additionally, the crystallinity of GECNFs was increased by 4.3 % and the resulting film exhibited low oxygen permeability rate (6.33 mL/m 2 ·day). Moreover, the combination post-treatments of enzyme and homogenization improved the tensile strength and transparency of CNFs films from 132.31 MPa, 27.52 %– to 177.99 MPa, 61.75 %, respectively. Besides, a composite of acrylic resin ABPE-10 and GEHCNFs film under negative pressure improved the transparency (85.68 %) and water contact angle (104.11°) of film. This work also provides insight on the relationship between the CNFs morphology and their film properties, which can be used to improve the CNFs film performance and promote future applications of CNFs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Thin film growth effects on electrical conductivity in entropy stabilized oxides

Entropy stabilization has garnered significant attention as a new approach to designing novel materials. Much of the work in this area has focused on bulk ceramic processing, leaving entropy-stabilized thin films relatively under-explored. Following an extensive multi-variable investigation of polycrystalline (Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 )O thin films deposited via pulsed laser deposition (PLD), it is shown here that substrate temperature and deposition pressure have strong and repeatable effects on film texture and lattice parameter. Further analysis shows that films deposited at lower temperatures and under lower oxygen chamber pressure are 40x less electrically resistive than otherwise identical films grown at higher temperature and pressure. Annealing these films in an oxygen-rich environment increases their electrical resistivity to match that of the films grown at higher temperatures and pressures. Because of this, the electric conductivity is hypothesized to be the result of polaron hopping mediated by transition metal valence changes which compensate for oxygen off-stoichiometry.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Study of synergistic effects and compositional dependence of hydrogen evolution reaction on MoxNiy alloy thin films in alkaline media

In this paper hydrogen evolution reaction (HER) on the molybdenum-nickel thin films has been studied. The Mo x Ni y thin films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). A change in the crystal structure of the samples prepared at different temperatures was observed. The structure of the samples prepared at 25 °C are bcc or amorphous. The structure of alloys sputtered at 800 °C changed to fcc. Tafel plots were constructed for each Mo x Ni y alloy sample. The mechanism of HER was determined from Tafel slope analysis. Values of charge transfer resistance were also determined by impedance spectroscopy. The compositional dependence of activity and the stability of Mo x Ni y thin films in 1 M NaOH were determined by cycling and chronoamperometry. Our results demonstrate that Mo x Ni y thin films prepared at 800 °C show significantly improved activity compared to pure Mo and Ni metals. On the other hand, Mo x Ni y thin films sputtered at 25°C do not show increased activity in comparison to pure Ni metal. Furthermore, this points to a synergistic effect between fcc Mo and fcc Ni in thin films sputtered at elevated temperatures. Mo 63 Ni 67 thin films alloy prepared at 800 °C shows the best values of catalytic activity for HER from all investigated compositions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tunable structural, morphological and optical properties of undoped, Mn, Ni and Ag-doped CuInS 2 thin films prepared by AACVD

The preparation of high-quality copper indium sulphide, CuInS 2 photo-absorber material with tunable properties for efficient, low-cost, thin film solar cells using scalable methods remains a challenge. In order to address this, high quality off-stoichiometric undoped and Mn, Ni and Ag-doped CuInS 2 (CIS) thin films have been deposited onto glass substrates by aerosol-assisted chemical vapour deposition (AACVD) using metal diethyldithiocarbamate precursors at temperatures of 350, 400 and 450 °C. Data from powder X-ray diffraction (p-XRD), Raman spectroscopy and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS) suggest a correlation of morphology and composition of tetragonal phase (chalcopyrite and copper-gold-type) sulphur-deficient microcrystalline CIS thin films. For undoped thin films, near-infrared optical absorption and emission with tunable band gap between 1.32 and 1.42 eV are likely associated with donor-acceptor pairs involving deep or shallow electronic states such as sulphur vacancies (V S •• ), indium-copper anti-sites (In Cu •• ) and indium interstitials (In i ••• ) as donors and copper vacancies (V Cu ') as acceptors. Whilst Mn-doped thin films exhibit minimal tunable properties, Ni and Ag-doped films exhibit tunable morphology, composition and near-infrared absorption for small dopant content. Here, though further studies are required to explore the defect chemistry, these results show the utility of AACVD in tuning structural, morphological and optical properties of undoped, Mn, Ni and Ag-doped CIS thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of Polyamide Thin Films by Atomic Force Microscopy

This study directly compares the mechanical behavior of novel molecular layer deposition (MLD) and analogous interfacial polymerization (IP) polyamide thin films in environments relevant to reverse osmosis (RO) membrane operation. The elastic modulus of the films was determined using atomic force microscopy (AFM) in dry, hydrated, and chlorinated states. Surface roughness characteristics were also obtained given their potential influence on AFM modulus measurements. The much smoother MLD films demonstrated a statistically higher modulus in all states as compared to their IP counterparts. The MLD films maintained a modulus ~3X and ~5X greater than that of IP films after hydration and chlorination, respectively. Such differences in behavior may be due to the higher density and correspondingly lower void content of the MLD films. Results from this study provide a rationale for future development of MLD for fabrication of polyamide films for incorporation in RO membranes.

atomic force microscopy↗
DOE OSTI2022

Toward Ideal Metal–Organic Framework Thin-Film Growth via Automated Layer-by-Layer Deposition: Examples Based on Perylene Diimide Linkers

Photoactive metal-organic framework (MOF) thin films offer an opportunity for translating the advantages of periodic, crystalline, and tailorable light-harvesting materials directly into devices such as those for photoelectrochemical solar energy conversion. In this study, we report the fabrication of light-absorbing perylene-diimide-containing pillared-paddlewheel MOF thin films using an automated layer-by-layer (LbL) deposition technique. Our focus here is on optimizing the growth of representative chromophoric MOFs as oriented films of uniform and predefined thickness. Growth was examined as a function of metal identity, pillaring ligand composition, and supporting-surface chemical functionality. Further, application of atomic force microscopy (AFM) and complementary techniques revealed that the surface-supported MOFs initially display island-type film growth (Volmer-Weber growth), resulting in comparatively rough films. Further growth is accompanied by the merging of islands, resulting in films that, depending on experimental details, can be remarkably smooth (i.e., roughness on the order of ±1 nm (one structural repeat unit in the pillaring direction)). These details include the use of 1,4-diazabicyclo[2.2.2]octane (DABCO) as a MOF pillar and ALD-grown zinc oxide as a film support (ALD = atomic layer deposition). Also helpful for mitigating island-type growth, at least in part, is the replacement of Zn 2+ by Cu 2+ as the metal component of the MOF. Notably, each of these adjustments entails replacing weaker chemical bonds with stronger ones.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Architecture-Dependent Thin Film Self-Assembly of Star Polystyrene-poly(2-vinylpyridine) Block Copolymers

Controlling the orientation of nanostructured block copolymer (BCP) thin films is essential for their use in templating, transport, and pattern transfer. Conventional efforts mainly focus on adjusting enthalpic interactions between the blocks and interfaces, while entropic contributions are often overlooked. Here, we show that the morphology of BCP thin films can be precisely tuned by the architectural design of star BCPs. Specifically, we synthesized multiarm star BCPs with a polystyrene (PS) core and poly(2-vinylpyridine) (P2VP) corona, which exhibits a lamellar microdomain morphology. The entropic penalty associated with a parallel orientation of the microdomains to the substrate is controlled by varying the number of arms comprising the star BCPs, from 2-arms (triblock) to 3-arms and 4-arms. We systematically investigated the thin film morphology at different depths using grazing incidence small-angle X-ray and neutron scattering (GISAXS and GISANS), atomic force microscopy (AFM), water contact angle (WCA), and interference microscopy. The results show that 2-arm star BCPs show a parallel orientation, the 3-arm star BCPs form a uniform PS film at the air surface with a vertical orientation of the microdomains underneath, and the 4-arm star BCPs exhibit a parallel microdomain orientation at the air surface with mixed parallel and perpendicular microdomain orientation in the bulk. Additionally, we found that the inclination angle of microdomains at the edges of islands and holes, resulting from the incommensurability between film thickness and the characteristic period of the microdomain morphology, increases with a higher number of arms. This suggests a greater grain boundary tilt angle in the microdomains of star-shaped block copolymers (BCPs). When silicon substrates were modified with PS homopolymer, the selective interaction between substrate and core blocks promotes a parallel orientation for the 4-arm star BCPs. In conclusion, this work shows that control of arm number in star BCPs affords diverse BCP thin film morphologies, offering insights into the star BCP conformations in thin films across different depths.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Surface Reconstruction in Hydrated Amphiphilic Block Copolymer Thin Films Probed by Fluid Cell Atomic Force Microscopy

In many thin film materials, nuanced interplays of interfacial energies control the surface morphology and rearrangement. This work evaluates polymer−solvent interactions and solvent-driven surface reconstructions via ex situ and in situ fluid cell Atomic Force Microscopy (fc-AFM) analysis of amphiphilic block copolymer (BCP) thin films upon exposure to deionized (DI) water. We examine the differences in surface morphology, whole-film swelling, and force response in thin films of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) and polystyrene- block-poly[(allyl glycidyl ether)-co-(ethylene oxide)] (PS-b- P[AGE-co-EO]) processed into standing-up cylinder morphologies perpendicular to a silicon substrate (⊥C). Using Amplitude Modulation AFM (AM-AFM) and Amplitude-Phase Distance (APD) force spectroscopy, this work probes the mechanoresponsive nature of the dynamic surface layers of these films, unveiling surface layer stratification and surface chain rearrangement via minimal tip−sample stimulation. To help rationalize the observed reconfigurations, the energetic driving forces were estimated using the harmonic mean approximations of interfacial energies. Given the nonionizable nature of the minority P(AGE-co-EO) block and the energetic driving forces for chain mobility, this work shows how the elimination of unfavorable PS−water interfaces drives chain rearrangement and coverage of the PS surface by chains of the hydrophilic block. This work highlights considerations for increasing the heterogeneity and complexity of BCP thin films via random blocks and how those changes to local interfacial energies may drive larger scale film morphology reconstructions, with broader implications for tuning interface hydrophilicity.

Copolymers↗
DOE OSTI2020

Ion-Conducting Thermoresponsive Films Based on Polymer-Grafted Cellulose Nanocrystals

Mechanically robust, thermo-responsive, ion-conducting nanocomposite films are prepared from poly(2-phenylethyl methacrylate) grafted cellulose nanocrystals (MxG-CNC-g-PPMA). One-component nanocomposite films of the polymer grafted nanoparticle (PGN) MxG-CNC-g-PPMA are imbibed with 30 wt% imidazolium-based ionic liquid, to produce flexible ion-conducting films. These films with 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (MxG-CNC-g-PPMA/[H]) not only displays remarkable improvements in toughness (>25 times) and tensile strength (>70 times) relative to the corresponding nanocomposites consisting of the ionic liquid imbibed in the two component CNC/PPMA nanocomposite, but also shows higher ionic conductivity than the corresponding neat PPMA with the same wt.% of ionic liquid. Notably, the one-component film containing 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (MxG-CNC-g-PPMA/[E]) exhibits temperature responsive ionic conduction. The ionic conductivity decreases at around 60°C as a consequence of the lower critical solution temperature (LCST) phase transition of the grafted polymer in the ionic liquid, which leads to phase separation. Moreover, holding the MxG-CNC-g-PPMA/[E] film at room temperature for 24 hours returns the film to its original homogenous state. These materials exhibit properties relevant to thermal cutoff safety devices (e.g., thermal fuse) where a reduction in conductivity above a critical temperature is needed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Controlling the Magneto-Optical Response in Ultrathin Films of EuO 1– x via Interface Engineering with Ferroelectric BaTi 2 O 5

Utilizing pulsed laser deposition, a film of EuO 1–x was deposited onto a Si(001) substrate with MgO buffer and compared to the same heterostructure with an additional BaTi 2 O 5 thin film on top of the EuO 1–x surface. X-ray diffraction (XRD) indicates the films crystallize into a preferred EuO(111) orientation; it also reveals the clear presence of EuSi 2 , which suggests Si or Eu diffuses across the MgO buffer layer. EuO 1–x films exhibit a ferromagnetic (FM) signature and temperature-dependent exchange bias, indicated by MOKE measurements, suggesting the presence of a magnetic order well above the EuO Curie temperature with possible origins in charge carrier density near the interface. In comparison, an antiferromagnetic character persists well above the EuO Curie temperature of 69 K and the enhanced Curie temperature of 150 K for BaTi 2 O 5 films grown on the EuO 1–x films. Furthermore, the antiferromagnetic behavior is not seen in thicker EuO 1–x thin films when integrated with other ferroelectric (FE) phases of the BaO–TiO 2 system, suggesting an origin in the perturbed charge population at the BaTi 2 O 5 /EuO 1–x interface.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exceptional Electrical Detection of Trace NO 2 via Mixed Metal MOF-on-MOF Film-Based Sensors

The tunability of metal–organic frameworks (MOFs) makes them exceptional materials for the development of highly selective, low-power sensors for toxic gas detection. Herein, we demonstrate enhanced detection of NO 2 gas by a MOF-based electrical impedance sensor made using a unique mixed metal MOF-on-MOF synthesis. For this work, a combined experimental and computational study was performed using the exemplar Ni x Mg 1–x -MOF-74 to understand the fundamental structure–property relationships behind metal mixing and MOF film synthesis methods on sensor performance. Density functional theory results indicated that the presence of Ni in Mg-MOF-74 increased framework stability and increased the electron density of states at lower energies near the HOMO, as well as enhanced the NO 2 –Mg adsorption interaction. Impedance data of the Ni x Mg 1–x -MOF-74 films with larger Ni contents showed greater impedance change after exposure to 1 ppm of NO 2 gas. Furthermore, when synthesized through either a drop-cast or direct solvothermal film growth approach, the monometallic Ni-based sensors had the best performance. However, the mixed metal Ni x Mg 1–x -MOF-74 sensors synthesized through a MOF-on-MOF approach resulted in the highest impedance change, outperforming all monometallic Ni-based sensors. In particular, the mixed metal Ni-on-Mg-MOF-74 film was the best-performing sensor with an impedance change of 309 upon trace NO 2 exposure. Change in impedance response after NO 2 exposure was improved by 52% compared to the best monometallic Ni-on-Ni-MOF-74 sensor. Structural analysis of the Ni-on-Mg film showed that the first Mg-MOF-74 layer acts as a structural template controlling the structural features of the final film after metal exchange with Ni. This led to improved film quality, evidenced by the greater crystallinity and larger MOF grain sizes, and resulted in enhanced sensor performance which was not achievable through other metal mixing methods. Altogether, this study identifies structure–property relationships and synthetic templating methods that inform MOF-based sensor design, allowing for improved detection of toxic compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrathin VO 2 Films on Functional Substrates

The metal–insulator transition (MIT) in vanadium dioxide (VO 2 ) thin films is strongly affected by grain size, thickness, and interfacial properties. Typically, a minimum thickness around 50 nm is required for VO 2 to exhibit a significant MIT when functional substrates like sapphire and silicon are used. Several works have shown that thin films below 20 nm, with up to 2–3 decades of change in the resistance across the MIT, can be achieved but require complex pre- or postprocessing of the samples. We show that predeposition substrate condition control facilitates the direct growth of VO 2 ultrathin 15 nm films, exhibiting a resistance change between 3 and 4 decades across the MIT. Our findings indicate that the interface between the film and the substrate is crucial in determining the initial growth layers and the structural evolution. With appropriate substrate surface treatment, the desired VO 2 MIT can be enhanced regardless of the substrate crystallographic orientation. Moreover, we propose a novel approach to obtain large resistance changes across the MIT in ultrathin VO 2 films by incorporating a predeposited 1.5 nm vanadium oxide buffer layer, thereby eliminating the need to use different materials or complex pre- or postprocessing of the samples. Here we also demonstrate that this method improves the transition of 25–50 nm VO 2 thin films on silicon substrates. Our study reveals a simple approach for direct growth of ultrathin VO 2 films exhibiting a significant MIT, which is commonly accepted unattainable over substrates of technological importance, such as sapphire and silicon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗